Search Results (41)

This paper investigates the cold rolling (CR) deformation behavior of electrolytic nickel at room temperature. While the microstructural evolution across deformation levels ranging from 5% to 98% is systematically characterized. The deposited electrolytic nickel exhibits numerous growth twins of various lengths and thicknesses, accounting for over 70% of the microstructure. The average grain size is 0.56 μm, and the grain size distribution is relatively broad. The plastic deformation of electrolytic nickel in the early stage is governed by the interaction between high-density dislocations and abundant twins. The primary mechanism accommodating deformation is detwinning. At 70% deformation, under high strain, complete detwinning occurs. When the CR reaches 90%, the average short-axis grain size is refined to 113 nm, indicating the deformation-induced refinement limit of electrolytic nickel. The microstructure at this stage exhibits a typical lamellar morphology. At 98% deformation, the average microhardness peaks at 240.3 HV, representing a cumulative increase of 46.88%. Dynamic recovery and recrystallization are observed at both 70% and 98% deformation levels, accompanied by the formation of Σ3 {120} type incoherent twins within recrystallized grains. Under large strain, the dominant cold plastic deformation mechanism transitions to a synergistic effect of dislocation slip and stratification. Full article

A roller straightening process of a pure magnesium strip, accompanied by alternating elastic-plastic deformation, was performed through one and three passes, where one pass corresponded to 19 bending events. It was discovered that roller straightening leads to the appearance of a kink in the specimen’s tensile stress–strain curve as well as an almost twofold decrease in the yield stress. This effect was observed only on longitudinal specimens. The conducted EBSD analysis confirmed the previously stated hypothesis about the influence of twinning on the change in the shape of the roller-straightened magnesium alloy specimen’s stress–strain curve. The tensile twins {$10\overline{1}2$} formed during roller straightening facilitate the detwinning process during subsequent tensile deformation, which, along with the basal sliding, is the reason for the decrease in yield stress. The scaling factor of the tensile specimens was investigated. Full article

This study employs molecular dynamics simulations to unravel the interplay between twin spacing, temperature, and mechanical response in nanotwinned AgPd alloys. For fine-grained systems, a dual strengthening–softening transition emerges as twin spacing decreases, driven by a shift in dislocation behavior from inclined-to-twin-boundary slip to parallel-to-twin-boundary glide. In contrast, coarse-grained configurations exhibit monotonic strengthening with reduced twin spacing, governed by strain localization at grain boundaries and suppressed dislocation activity. Notably, cryogenic conditions stabilize pre-existing and nascent twins, whereas elevated temperatures intensify atomic mobility and boundary migration, accelerating twin boundary annihilation (“detwinning”). Full article

In this study, a probabilistic model within the dislotwin constitutive framework of DAMASK (the Düsseldorf Advanced Material Simulation Kit) was established to describe the cyclic loading behaviors of AZ31B magnesium alloys. Considering the detwinning procedure within the twinned region, this newly developed dislocation–twinning–detwinning model was employed to accurately simulate stress–strain behaviors of AZ31B magnesium alloys throughout tension–compression–tension (T-C-T) cycle loading. The investigations revealed that the reduction in yield stress during the reverse loading process was attributed to the active operation of twinning and detwinning modes. Furthermore, the evolution of the twin volume fraction during cycle loading scenarios was quantitatively determined. According to these results, the relative activities of plastic deformation modes during T-C-T loading were further analyzed. Full article

This study investigates the preparation of ultrahigh-strength AZ80 magnesium alloy bulks using room temperature multidirectional forging (MDF) at different strain rates. The focus is on elucidating the effects of multidirectional loading and strain rates on grain refinement and the subsequent impact on the mechanical properties of the AZ80 alloy. Unlike hot deformation, the alloy subjected to room temperature MDF exhibits a lamellar twinned structure with multi-scale interactions. The key to achieving effective room temperature MDF of the alloy lies in combining multidirectional loading with small forging strains per pass (6%). This approach not only maximizes the activation of twinning to accommodate deformation but ensures sufficient grain refinement. Microstructural analysis reveals that the evolution of the grain structure in the alloy during deformation results from the competition between {10$\overline{1}$2} twinning or twinning variant interactions and detwinning. Increasing the forging rate effectively activates more twin variants, and additional deformation passes significantly enhance twin interaction levels and dislocation density. Furthermore, at a higher strain rate, more pronounced dislocation accumulation facilitates the transformation of twin structures into high-angle grain boundaries, promoting texture dispersion and suppressing detwinning. The primary strengthening mechanisms in room temperature MDF samples are grain refinement and dislocation strengthening. While increased dislocation density raises yield strength, it reduces post-yield work hardening capacity. After two passes of MDF at a higher strain rate, the alloy achieves an optimal balance of strength and ductility, with a tensile strength of 462 MPa and an elongation of 5.1%, significantly outperforming hot-deformed magnesium alloys. Full article

The precipitation behavior of Cu-bearing ultra-low carbon steel after step quenching and tempering at 923 K for 0.5–2.5 h was investigated. The size, quantity, and characteristic distribution of nano-precipitates were analyzed using transmission electron microscopy, and the microstructure of B2 (an ordered structure belonging to the body-centered cubic structure), 9R (a special triclinic lattice that has characteristics of rhombohedral structure), 3R (a special triclinic lattice like 9R), and FCT (face-centered tetragonal lattices) were accurately determined. The relationship between nano-precipitates and mechanical properties under different heat treatment processes was obtained, revealing that nano-precipitates effectively enhanced the yield strength of Cu-bearing ultra-low carbon steel. There were two forms of crystal structure evolution sequence of precipitation: B2→multi twin 9R→detwined 9R→FCT→FCC and B2→multi-twin 9R→detwinned 9R→3R→FCT→FCC. The morphology of the precipitated particles during the growth process changed from spherical to ellipsoidal and finally to rod-shaped. It was proven that a stable 3R structure existed due to the coexistence of 9R, 3R, and FCT structures in the same precipitate particle. Full article

In the present study, the mechanical response and deformation behavior of a Mg AZ31 plate with different types of pre-twins was systematically investigated under biaxial tension along the normal direction (ND) and transverse direction (TD) with different stress ratios. The results show that significant hardening was observed under biaxial tension. The yield values in the direction of larger stress values were higher than those under uniaxial loading conditions, and the solute atom segregation at twin boundaries generates more obvious strengthening effect. Noting that, for TRH (with cross compression along the rolling direction (RD) and TD and annealing at 180 °C for about 0.5 h) sample, the strength effect of the RD yield stress ${\mathsf{\sigma }}_{\mathrm{RD}}:{\mathsf{\sigma }}_{\mathrm{ND}}$ = 2:1 was higher than that of the ND yield stress under stress ratio ${\mathsf{\sigma }}_{\mathrm{RD}}:{\mathsf{\sigma }}_{\mathrm{ND}}$ = 1:2. There is a complex competition between twinning and detwinning under biaxal tension along the ND and TD of the pre-twinned samples with the variation in the stress ratio along the TD and RD. The variation in the twin volume fractions for all samples under biaxial firstly decreases and then increases with a higher stress ratio along the ND. As for the TDH sample (precompression along the TD and annealing), the changes of the twin volume fraction were lower than that of the TR sample (cross compression along the TD and RD). However, the amplitude of variation in twin volume fraction of the TRH sample is higher than that of the TR sample. This is because the relative activity of detwinning decreases and that of twinning increases, as the ND stress mainly leads to the growth of pre-twins and the TD stress often promotes detwinning of primary twins. With a higher stress ratio along the ND, the activity of twinning deformation increases and that of detwinning decreases. Full article

The deformation behavior of a high-strength Mg-Al-Sn-Zn alloy under loading reversals has been thoroughly examined through a combination of experimental measurements and crystal plasticity modeling. We focused on an age-treated alloy fortified by distributed Mg₂Sn particles and Mg₁₇Al₁₂ precipitates, which underwent two distinct loading cycles: tension-compression-tension (TCT) and compression-tension-compression (CTC), aligned with the extrusion direction (ED). The initial and deformed microstructures of the alloy were analyzed using the electron backscattering diffraction (EBSD) technique. Notably, the alloy displays tensile and compressive yield strengths (YS) of 215 MPa and 160 MPa, respectively, with pronounced anelastic behavior observed during unloading and reverse loading phases. Utilizing the elasto-viscoplastic self-consistent model incorporating a twinning–detwinning scheme (EVPSC-TDT), the cyclic stress–strain responses and resultant textures of the alloy were accurately captured. The predicted alternation between various slip and twinning modes during plastic deformation was used to interpret the observed behaviors. It was found that prismatic <a> slip plays an important role during the plastic deformation of the studied alloy, and its relative activity in tensile loading processes accounts for up to ~66% and ~67% in the TCT and CTC cases, respectively. Moreover, it was discerned that detwinning and twinning behaviors are predominantly governed by stresses within the parent grain, and they can concurrently manifest during the reverse tensile loading phase in the TCT case. After cyclic deformation, the area fractions of residual twins were determined to be 7.51% and 0.93% in the TCT and CTC cases, respectively, which is a result of the varied twinning–detwinning behavior of the alloy in different loading paths. Full article

Magnesium alloys, being the lightest structural metals, have garnered significant attention in various fields. The characterization of inelastic behavior has been extensively investigated by researchers due to its impact on structural component performance. However, the occurrence of twinning in the absence of any applied driving force during unloading has lacked reasonable explanations. Moreover, the influence of deformation mechanisms other than twinning on inelastic behavior remains unclear. In this study, uniaxial tension and compression tests were conducted on hot-rolled magnesium alloy plates, and neutron diffraction experiments were employed to characterize the evolution of macroscopic mechanical response and microscopic mechanisms. Additionally, a twinning and detwinning (TDT) model based on the elastic visco-plastic self-consistent (EVPSC) model has been proposed, incorporating back stress to describe the deformation behavior during stress relaxation. This approach provides a comprehensive understanding of the inelastic behavior of magnesium alloys from multiple perspectives and captures the influence of microscale mechanisms. A thorough understanding of the inelastic behavior of magnesium alloys and a reasonable explanation for the occurrence of twinning under zero-stress conditions offer valuable insights for the precise design of magnesium alloy structures. Full article

Under strain control tests and cyclic loading, extruded magnesium alloys exhibit a special mechanism of plastic deformation (“twinning” and “de-twining”). As a result, magnesium alloys exhibit an asymmetric material behavior that cannot be fully characterized with the typical numerical tools used for steels or aluminum alloys. In this sense, a new phenomenological model, called hypo-strain, has been developed to correctly predict the cyclic stress–strain evolution of magnesium alloys. On this basis, this work aims to accurately describe the local cyclic elastic–plastic behavior of AZ31B-F magnesium alloy under multiaxial cyclic loading with Abaqus incremental plasticity. The phenomenological hypo-strain model was implemented in the UMAT subroutine of Abaqus/Standard to be used as a design tool for mechanical design. To evaluate this phenomenological approach, the results were correlated with the uniaxial and multiaxial proportional and non-proportional experimental tests. In addition, the estimates were also correlated with the Armstrong–Frederick nonlinear kinematic hardening model. The results show a good correlation between the experiments and the phenomenological hypo strain approach. The model and its implementation were validated in the strain range studied. Full article

In this article, a microstructural model of the Heusler alloy with the shape memory effect caused by the application of an external magnetic field is constructed. The dynamics of the magnetization process are described using the Landau–Lifshitz–Gilbert equation. For the numerical implementation of the model using the finite element method, the variational equations corresponding to the differential formulation of the magnetic problem are used. Such an approach makes it possible to reduce (weaken) the requirements for the smoothness of the sought solution. The problem of magnetization of single crystals of the Ni₂MnGa alloy, which has a “herringbone”-type martensitic structure (a twinned variant of martensite), is considered. In each element of the twin, the magnetic domains with walls of a certain thickness are formed. The motion and interaction of these walls and the rotation of magnetization vector in the walls and domains under the action of the external differently directed magnetic fields are studied. These processes in the Heusler alloy are also accompanied by the detwinning process. A condition for the detwinning of a ferromagnetic shape memory alloy in a magnetic field is proposed, and the effect of the reorientation (detwinning) of martensitic variants forming a twin on the magnetization of the material and the occurrence of structural (detwinning) deformation in it are taken into account. First, the processes of magnetization and structural deformation in a single grain are considered at different angles between the anisotropy axes of twinned variants and the external magnetic field. For these cases, the magnetization curves are constructed, and the deformed states are identified. The model described such experimental facts as the detwinning process and the jump in magnetization on these curves as a result of this process. It was shown that the jump occurred at a certain magnitude of the strength of the applied external magnetic field and a certain direction of its action relative to the twinning system. Then, based on the obtained results, deformed states arising due to the detwinning process were determined for various (isotropic and texture-oriented) polycrystalline samples, and magnetization curves taking into account this process were constructed for these materials. Full article

The nanoscopic deformation of ⟨111⟩ nanotwinned copper nanopillars under strain rates between 10⁻⁵/s and 5 × 10⁻⁴/s was studied by using in situ transmission electron microscopy. The correlation among dislocation activity, twin boundary instability due to incoherent twin boundary migration and corresponding mechanical responses was investigated. Dislocations piled up in the nanotwinned copper, giving rise to significant hardening at relatively high strain rates of 3–5 × 10⁻⁴/s. Lower strain rates resulted in detwinning and reduced hardening, while corresponding deformation mechanisms are proposed based on experimental results. At low/ultralow strain rates below 6 × 10⁻⁵/s, dislocation activity almost ceased operating, but the migration of twin boundaries via the 1/4 ⟨$10\overline{1}$ ⟩ kink-like motion of atoms is suggested as the detwinning mechanism. At medium strain rates of 1–2 × 10⁻⁴/s, detwinning was decelerated likely due to the interfered kink-like motion of atoms by activated partial dislocations, while dislocation climb may alternatively dominate detwinning. These results indicate that, even for the same nanoscale twin boundary spacing, different nanomechanical deformation mechanisms can operate at different strain rates. Full article

Owing to the excellent mechanical properties of the Ti₃Al alloy, the study of its microstructure has attracted the extensive attention of researchers. In this study, a Ti₃Al alloy was grown based on molecular dynamics using a decahedral precursor. Face centered cubic nanocrystals with tetrahedral shapes were formed and connected by twin boundaries (TBs) to form penta twins. To understand the shear response of the Ti₃Al alloy with multiple and penta twins, a shear load perpendicular to the Z-axis was applied to the quenched sample. The TBs slipped as Shockley dislocations commenced and propagated under shear loading, causing the detwinning of the penta twins and the failure of the system, indicating that the plastic deformation had been due to Shockley dislocations. The slip mechanism of multi-twinned structures in the Ti₃Al alloy is discussed in detail. This study would serve as a useful guide for the design and development of advanced alloy materials. Full article

In this article, based on the theory of micromagnetism, a microstructural model of the behavior of the Heusler alloy in a magnetic field is constructed. The dynamics of the magnetic process is described by the Landau–Lifshitz–Gilbert equation. Using the Galerkin procedure, variational equations corresponding to the differential relations of the magnetic problem are written out. For numerical simulation, we consider the problem of magnetization of a Ni${}_2$MnGa alloy polytwin crystals, each grain of which is a twinned variant of martensite and has pronounced anisotropic properties. First, we consider the process of magnetization of a single grain, when an external magnetic field is applied at different angles to the anisotropy axes of twinned variants, and then, based on the results obtained, we plot magnetization curves for various (isotropic and texture-oriented) polycrystalline samples. This paper does not consider the process of detwinning, which can occur in such a material during the magnetization at a sufficiently high external field strength. Full article

Shape memory alloy (SMA) is one of the potential driving devices for morphing aircraft due to its advantages of pseudoelasticity, superelasticity, and shape memory effect. Precise and fast analysis of SMA has simultaneously become a key requirement for industrial applications. In this study, a user-defined material subroutine (UMAT) was implemented and successfully applied in a three-dimensional numerical simulation in ABAQUS based on the extended Boyd–Lagoudas model. In addition to the conventional detwinned martensite (M_d) and austenite (A), twinned martensite (M_t) was also considered to model the practical transformation accurately. Then, the equivalent thermal strain approach was adopted to simplify the simulation complexity with UMAT. By resetting the thermal expansion coefficient, the thermal strain equivalent to the original phase transformation strain was generated. The approach was validated in two cases, showing consistent results with the extended Boyd–Lagoudas model and reduction in time consumption by 89.1%. Lastly, an active morphing skin integrating the single-range SMA and a stainless-steel plate was designed to realize two-way morphing. The calculated arc height variation of the skin was 3.74 mm with a relative error of 1.84% compared to the experimental result of 3.81 mm. The coupled use of UMAT and the equivalent thermal stress approach helped to reduce the challenge in modeling SMA. Full article