Search Results (112)

In the present study, a polarization rotation switch (PRS)-based all-optical ternary inverter circuit and ternary clocked SR flip-flop (TCSR) are proposed and discussed. The present scheme is designed by the polarization rotation of light in a waveguide coupled with a micro-ring resonator (MRR). The proposed scheme uses linear polarization-encoded light. Here, the ternary (radix = 3) logical states are expressed by the different polarized light. PRS-MRR explores the polarization-encoded methodology, which depends on polarization conversion from one state to another. All-optical ultrafast switching technology is employed to design the ternary NAND gate. We develop the ternary clocked SR flip-flop by employing the NAND gate; it produces a greater number of possible outputs as compared to the binary logic clocked SR flip-flop circuit. The performance of the proposed design is measured by the Jones parameter and Stokes parameter. The results of the polarization rotation-based ternary inverter and clocked SR flip-flop are realized using a pump–probe structure in the MRR. The numerical simulation results are confirmed by the well-known Jones vector (azimuth angle and ellipticity angle) and Stokes parameter (S₁, S₂, S₃) using Ansys Lumerical Interconnect simulation software. Full article

A kind of magnetoplasmonic resonators is numerically designed with hexagonally arrayed Au/bismuth iron garnet (BIG) bilayer nanodiscks on Au thin film layers. Multi-physics coupling calculation on their magnetoplasmonic resonance features suggest that there exists a strong resonant coupling between the surface plasmon excited by the hexagonal grating and the waveguide modes induced by Au-BIG-Au, which can significantly enhance the transverse magneto-optical Kerr effect. Interestingly, a new type of circular oscillating can be induced in the optical-transparent BIG layers as the thickness of BIG layers is between 2 nm and 22 nm. This circular oscillating exhibits a distinct thickness-dependent feature, which can be attributed to the near field interference of the excited localized plasmon resonance between the two interfaces formed by the middle BIG nanodiscs in the top Au nanodisks and the bottom Au thin film layers according to the simulation. These unique magnetoplasmonic features endow this kind of magnetoplasmonic resonators with a greatly enhanced refractive index sensing property, with a calculated figure of merit (FOM) value of up to 7527 RIU⁻¹. Full article

Despite significant progress, fabricating two-dimensional (2D) lithium niobate (LN)-based photonic crystal (PhC) cavities integrated with tapered and PhC waveguides remains challenging, due to structural imperfections. Notable, especially, are variations in hole radius (r) and inclination angle (°), which induce bandgap shifts and degrade quality factors (Q-factor). These fabrication errors underscore the critical need to address nanoscale tolerances. Here, we systematically investigate the impacts of key geometric parameters on optical performance and optimize a 2D LN-based cavity integrated with taper and PhC waveguide system. Using a 3D Finite-Difference Time-Domain (FDTD) and varFDTD simulations, we identify stringent fabrication thresholds. The a must exceed 0.72 µm to sustain Q > ${10}^7$; reducing a to 0.69 µm collapses Q-factors below ${10}^4$, due to under-coupled modes and bandgap misalignment, which necessitates ±0.005 µm precision. When an r < 0.22 µm weakens confinement, Q plummets to 2 × ${10}^4$ at r = 0.20 µm (±0.01 µm etching tolerance). Inclination angles < 70° induce 100× Q-factor losses, requiring ±2° alignment for symmetric modes. Air slot width (s) variations shift resonant wavelengths and require optimization in coordination with the inclination angle. By optimizing s and the inclination angle (at 70°), we achieve a record Q-factor of 6.21 ×${10}^6$, with, in addition, C-band compatibility (1502–1581 nm). This work establishes rigorous design–fabrication guidelines, demonstrating the potential for LN-based photonic devices with high nano-fabrication robustness. Full article

Nanoplasmonic structures have emerged as a promising approach to address light trapping limitations in thin-film optoelectronic devices. This study investigates the integration of metallic nanoparticle arrays onto nanocrystalline silicon (nc-Si:H) thin films to enhance optical absorption through plasmonic effects. Using finite-difference time-domain (FDTD) simulations, we systematically optimize key design parameters, including nanoparticle geometry, spacing, metal type (Ag and Al), dielectric spacer material, and absorber layer thickness. The results show that localized surface plasmon resonances (LSPRs) significantly amplify near-field intensities, improve forward scattering, and facilitate coupling into waveguide modes within the active layer. These effects lead to a measurable increase in integrated quantum efficiency, with absorption improvements reaching up to 30% compared to bare nc-Si:H films. The findings establish a reliable design framework for engineering nanoplasmonic architectures that can be applied to enhance performance in photovoltaic devices, photodetectors, and other optoelectronic systems. Full article

We investigate integrated silicon ring resonators with regard to the influence of design parameters and intra-wafer variations. First, we show the effect of different ring radii and gaps between ring and bus waveguide on optical properties (peak width, finesse, Q factor, and extinction ratio), from which we calculate the resonators’ coupling and loss coefficients. The dependence on the gap of these properties is discussed at the wafer scale. Second, by incorporating the spectra of 2242 resonators from 59 nominally identical dies on a 200 mm wafer, we show how these properties depend on the resonators’ position on the wafer. Third, we demonstrate how curve fitting of loss and coupling coefficients as a function of the gaps can be used to estimate the optimal gap that realizes critical coupling with a significantly reduced number of manufactured test structures needed to find optimal design parameters. Full article

Plasmon waveguide resonances (PWRs) have been widely used to enhance the interaction between light and matter. PWRs have been used for chemical and biological sensing, molecular detection, and boosting other optical phenomena, such as Raman scattering and fluorescence. However, the performances of plasmon-waveguide-based structures have been investigated in the angular interrogation mode, and their potential in different spectral regions has hardly been explored. Moreover, the applications of PWRs have been limited to the weak light–matter coupling regime. In this study, we investigate leaky coupled waveguide plasmon resonances (LCWPRs) and explore their potential to enhance light–matter interaction in different spectral regions. In the weak coupling regime, we demonstrate the potential of LCWPRs for sensing in the near-IR region by detecting heavy water (D₂O) and ethanol in water. The experimental results show spectral sensitivity of 15.2 nm/% and 1.41 nm/% for ethanol and D₂O detection, respectively. Additionally, we show that LCWPRs can be used to achieve vibrational strong coupling (VSC) with organic molecules in the mid-IR region. We numerically show that the coupling between LCWPRs and the C=O stretching vibration of hexanal yields a Rabi splitting of 210 cm⁻¹, putting the system in the VSC regime. We anticipate that LCWPRs will be a promising platform for enhanced spectroscopy, sensing, and strong coupling. Full article

We propose a simple and innovative configuration consisting of a quantum dot and micro-optical resonator that emits single photons with good directionality in a plane parallel to the substrate. In this device, a single quantum dot is placed as a light source between the slits of a triangular split-ring micro-optical resonator (SRR) supported in an optical polymer film with an air-bridge structure. Although most of the previous single photon emitters in solid-state devices emitted photons upward from the substrate, operation simulations confirmed that this configuration realizes lateral light emission in narrow regions above, below, left, and right in the optical polymer film, despite the absence of a light confinement structure such as an optical waveguide. This device can be fabricated using silica-coated colloidal quantum dots, focused ion beam (FIB) lithography, and wet etching using an oxide layer on a silicon substrate as a sacrificial layer. The device has a large tolerance to the variation in the position of the SRR in the optical polymer film and the height of the air-bridge. We confirmed that Pt-SRRs can be formed on the optical polymer film using FIB lithography. This simple lateral photon emitter is suitable for coupling with optical fibers and for fabricating planar optical quantum solid-state circuits, and is useful for the development of quantum information processing technology. Full article

Terahertz is one of the most promising technologies for high-speed communication and large-scale data transmission. As a classical optical component, ring resonators are extensively utilized in the design of band-pass and frequency-selective devices across various wavebands, owing to their unique characteristics, including optical comb generation, compactness, and low manufacturing cost. While substantial progress has been made in the study of ring resonators, their application in terahertz surface wave systems remains less than fully optimized. This paper presents several spoof surface plasmon polariton-based devices, which were realized using ring resonators at terahertz frequencies. The influence of both the radius of the ring resonator and the width of the waveguide coupling gap on the coupling coefficient are investigated. The band-stop filters based on the cascaded ring resonator exhibit a 0.005 THz broader frequency bandwidth compared to the single-ring resonator filter and achieve a minimum stopband attenuation of 28 dB. The add–drop multiplexers based on the asymmetric ring resonator enable selective surface wave outputs at different ports by rotating the ring resonator. The devices designed in this study offer valuable insights for the development of on-chip terahertz components. Full article

With the rapid advancement of information technology, the data demands in transmission rates, processing speed, and storage capacity have been increasing significantly. However, silicon electro-optic modulators, characterized by their weak electro-optic effect, struggle to balance modulation efficiency and bandwidth. To overcome this limitation, we propose an electro-optic modulator based on an all-fiber micro-ring resonator and a p-Si/n-ITO heterojunction, achieving high modulation efficiency and large bandwidth. ITO is introduced in this design, which exhibits an ε-near-zero (ENZ) effect in the communication band. The real and imaginary parts of the refractive index of ITO undergo significant changes in response to variations in carrier concentration induced by the reverse bias voltage, thereby enabling efficient electro-optic modulation. Additionally, the design of the all-fiber micro-ring eliminates coupling losses associated with spatial optical-waveguide coupling, thereby resolving the high insertion loss of silicon waveguide modulators and the challenges of integrating MZI modulation structures. The results demonstrate that this modulator can achieve significant phase shifts at low voltages, with a modulation efficiency of up to 3.08 nm/V and a bandwidth reaching 82.04 GHz, indicating its potential for high-speed optical chip applications. Full article

The integration of a photodetector that converts optical signals into electrical signals is essential for scalable integrated lithium niobate photonics. Two-dimensional materials provide a potential high-efficiency on-chip detection capability. Here, we demonstrate an efficient on-chip photodetector based on a few layers of MoTe₂ on a thin film lithium niobate waveguide and integrate it with a microresonator operating in an optical telecommunication band. The lithium-niobate-on-insulator waveguides and micro-ring resonator are fabricated using the femtosecond laser photolithography-assisted chemical–mechanical etching method. The lithium niobate waveguide-integrated MoTe₂ presents an absorption coefficient of 72% and a transmission loss of 0.27 dB µm⁻¹ at 1550 nm. The on-chip photodetector exhibits a responsivity of 1 mA W⁻¹ at a bias voltage of 20 V, a low dark current of 1.6 nA, and a photo–dark current ratio of 10⁸ W⁻¹. Due to effective waveguide coupling and interaction with MoTe₂, the generated photocurrent is approximately 160 times higher than that of free-space light irradiation. Furthermore, we demonstrate a wavelength-selective photonic device by integrating the photodetector and micro-ring resonator with a quality factor of 10⁴ on the same chip, suggesting potential applications in the field of on-chip spectrometers and biosensors. Full article

A novel 4-to-2 photonic crystal encoder is proposed by modulating the intensity of four input optical signals, and four distinct output states are achieved. Nonlinear rods are employed to couple input waves into resonant cavities, directing the light to the desired output waveguides. The proposed design, with a footprint of 114 µm², demonstrates efficient encoding operation at a wavelength of 1550 nm and is highly suitable for integrated photonics applications. A comprehensive comparative analysis revealed that the proposed 4-to-2 encoder exhibits a time response 176 fs faster than previously presented encoders. Furthermore, the contrast ratio of the designed structure is as high as 13.78 dB to distinguish between logic 0 and 1. These advancements hold significant potential for enhancing the performance of compact, high-speed digital circuits. Full article

We propose two types of structures to achieve the control of Fano and electromagnetically induced transparency (EIT) line shapes, in which dual one-dimensional (1D) photonic crystal nanobeam cavities (PCNCs) are side-coupled to a bus waveguide with different gaps. For the proposed type Ⅰ and type Ⅱ systems, the phase differences between the nanobeam periodic structures of the two cavities are π and 0, respectively. The whole structures are theoretically analyzed via the coupled mode theory and numerically demonstrated using the three-dimensional finite-difference time-domain (3D FDTD) method. The simulation results show that the proposed structure can achieve several kinds of spectra, including Fano, EIT and asymmetric EIT line shapes, which is dependent on the width of the bus waveguide. Compared to the previously proposed Fano resonator with 1D PCNCs, the proposed structures have the advantages of high transmission at the resonant peak, low insertion loss at non-resonant wavelengths, a wide free spectral range (FSR) and a high roll-off rate. Therefore, we believe the proposed structure can find broad applications in optical switches, modulators and sensors. Full article

Integrated optical amplifiers are the building blocks of on-chip photonic systems, and they are often accompanied by a narrowband filter to limit noise. In this sense, a bandwidth-tunable optical amplifier with narrowband filtering function is crucial for on-chip optical circuits and radio frequency systems. The intrinsic loss and coupling coefficients between resonator and waveguide inherently limit the bandwidth. The parity-time symmetric coupled microresonators operating at exceptional points enable near zero bandwidth. In this study, we propose a parity-time symmetric coupled microresonators system operating near EPs to achieve a bandwidth of 46.4 MHz, significantly narrower than bandwidth of 600.0 MHz and 743.2 MHz achieved by two all-pass resonators with identical gain/loss coefficients. This system also functions as an optical bandwidth-tunable filter. The bandwidth tuning ranges from 175.7 MHz to 7.8 MHz as gain coefficient adjusts from 0.2 dB/cm to 0.4 dB/cm. Our scheme presents a unique method to obtain narrow bandwidth from two broadband resonators and serves as an optical bandwidth-tunable filter, thereby paving a new avenue for exploring non-Hermitian light manipulation in all-optical integrated devices. Full article

The intrinsic third-order nonlinearity in silicon has proven it to be quite useful in the field of quantum optics. Silicon is suitable for producing time-correlated photon pairs that are sources of heralded single-photon states for quantum integrated circuits. A quantum signal source in the form of single photons is an inherent requirement for the principles of quantum key distribution technology for secure communications. Here, we present numerical simulations of a silicon ring with a 6 μ m radius side-coupled with a bus waveguide as the source for the generation of single photons. The photon pairs are generated by exploring the process of degenerate spontaneous four-wave mixing (SFWM). The free spectral range (FSR) of the ring is quite large, simplifying the extraction of the signal/idler pairs. The phase-matching condition is considered by studying relevant parameters like the dispersion and nonlinearity. We optimize the ring for a high quality factor by varying the gap between the bus and the ring waveguide. This is the smallest ring studied for photon pair generation with a quality factor in the order of 10 5 . The width of the waveguides is chosen such that the phase-matching condition is satisfied, allowing for the propagation of fundamental modes only. The bus waveguide is pumped at one of the ring resonances with the minimum dispersion (1543.5 nm in our case) to satisfy the principle of energy conservation. The photon pair generation rate achieved is comparable to the state of the art. The photon pair sources exploiting nonlinear frequency conversion/generation processes is a promising alternative to atom-like single-photon emitters in the field of integrated photonics. Such miniaturized structures will benefit future on-chip architectures where multiple single-photon source devices are required on the same chip. Full article