Search Results (8)

The pharmaceutical industry is a major source of pollution in wastewater effluents, characterized by chemical residues that are complex and difficult to degrade. Naproxen, a commonly detected drug in sewage effluents, exceeds safe concentrations for aquifers and is highly persistent, posing significant risks to aquatic life and ecosystems. This drug is known to cause long-term side effects in humans, such as gastrointestinal ulcers and nephrosis, associated with frequent and prolonged use. Additionally, the recent pandemic has led to a marked increase in drug consumption over a short period, exacerbating environmental contamination. Titanium dioxide has been extensively used as a photocatalyst in recent decades, proving effective in reducing these emerging pollutants. In this study, TiO₂ doped with cerium was synthesized using the sol–gel method, with cerium concentrations varied at 1, 3, 5, and 10% by weight. The resulting nanocatalysts were characterized through nitrogen physisorption, scanning electron microscopy (SEM), X-ray diffraction (XRD), and UV-Vis diffuse reflectance spectroscopy. Photocatalytic activity was assessed using a UV-Vis spectrophotometer to monitor the degradation of the drugs. XRD analysis confirmed the crystallinity and anatase phase of TiO₂. UV-Vis diffuse reflectance spectra indicated a decrease in bandgap energy of up to 3.00 eV compared to pure TiO₂. The materials demonstrated significant degradation of naproxen (NPX) and acetaminophen (ACTP), both prepared at 30 ppm, over a 6 h reaction period. Full article

Humidity sensing elements based on sodium-doped titanium dioxide (Na-doped TiO₂) were prepared using a sol–gel method in the presence of cerium ions and sintered at 400 °C and 800 °C. Titanium (IV) n-butoxide and a saturated solution of diammonium hexanitratocerate in isobutanol served as starting materials. Sodium hydroxide and sodium tert-butoxide were used as inorganic and organometallic sodium sources, respectively. The influence of sodium additives on the properties of the humidity sensing elements was systematically investigated. The surface morphologies of the obtained layers were examined by scanning electron microscopy (SEM). Elemental mapping was conducted by energy-dispersive X-ray (EDX) spectroscopy, and structural characterization was performed using X-ray diffractometry (XRD). Electrical properties were studied for samples sintered at different temperatures over a relative humidity range of 15% to 95% at 20 Hz and 25 °C. Experimental results indicate that sodium doping enhances humidity sensitivity compared to undoped reference samples. Incorporation of sodium additives increases the resistance variation range of the sensing elements, reaching over five orders of magnitude for samples sintered at 400 °C and four orders of magnitude for those sintered at 800 °C. Full article

Recently, aquatic life and human health are seriously threatened by the release of pharmaceutical drugs. For a sustainable ecosystem, emerging contaminants like antibiotics must be removed from drinking water and wastewater. To address this issue pure and cerium-doped titanium dioxide (CeT) nanoparticles were produced with stable tetragonal (anatase) lattices by room temperature sol–gel method and employing the inorganic titanium oxysulfate (TiOSO₄) as titanium precursor. The structural analysis by X-ray diffraction (XRD) revealed that at calcination temperature of 600 °C all (un and doped) powders were composed of crystalline anatase TiO₂ with the crystallite sizes in the range of 13.5–11.3 nm. UV–vis DRS spectroscopy revealed that the most narrowed bandgap value of 2.75 eV was calculated for the 0.5CeT sample containing the optimum dopant content of 0.5 weight ratio. X-ray spectroscopy (XPS) confirmed the presence of the impurity level Ce³⁺/Ce⁴⁺, which became responsible for the decrease in bandgap as well as for the photoinduced carriers recombination rate. Photocatalytic tests showed that the maximum decomposition of the model spiramycin (SPR) antibiotic pollutant was 88.0% and 77.0%, under UV and visible light, respectively. According to the reaction kinetics, SPR decomposition adhered to the Langmuir–Hinshelwood (L–H) model and via ROS experiments mainly hydroxyl radicals (OH^•) followed by photogenerated holes (h⁺s) become responsible for the pollutant degradation. In summary, this study elaborates on the role of xCeT nanoparticles as an efficient photocatalyst for the elimination of organic contaminants in wastewater. Full article

The increased production of biodiesel results in a corresponding rise in the production of glycerol (GLY) as a by-product. The selective oxidation of glycerol can yield relatively simple products under mild reaction conditions, offering high added value and positioning it as one of the most promising methods for industrialization. In this study, we employed black titanium dioxide (B-TiO₂) as a support and deposited platinum (Pt) to create a noble metal-supported catalyst. Lanthanum (La) or cerium (Ce) was doped into B-TiO₂ to enhance the concentration of oxygen vacancies in the support, thereby improving catalyst activity. Throughout the research process, we also investigated the impact of varying amounts of La or Ce doping on catalyst performance. Analysis of the catalytic experimental data revealed that Pt/30%Ce-B-TiO₂ exhibited the highest catalytic performance. Structural analysis of the catalysts showed that the synergistic effect between Pt⁰ and oxygen vacancies contributed to enhancing catalyst activity. Full article

In this study, original titanium dioxide (TiO₂) and cerium (Ce)-doped TiO₂ nanorod array photoanodes are prepared by hydrothermal method combined with high-temperature annealing, and their morphology, photoelectrochemical properties, and photocatalytic hydrogen production ability are systematically evaluated. X-ray diffraction (XRD) analysis shows that as the Ce content increases, the diffraction peak of the rutile phase (110) shifts towards lower angles, indicating the successful doping of different contents of Ce into the TiO₂ lattice. Photoelectric performance test results show that Ce doping significantly improves the photocurrent density of TiO₂, especially for the 0.54wt% Ce-doped TiO₂ (denoted as CR5). The photocurrent density of CR5 reaches 1.98 mA/cm² at a bias voltage of 1.23 V (relative to RHE), which is 2.6 times that of undoped TiO₂ (denoted as R). Photoelectrochemical hydrolysis test results show that the hydrogen yield performance under full-spectrum testing conditions of Ce-doped TiO₂ photoanodes is better than that of original TiO₂ as well, which are 37.03 and 12.64 µmol·cm⁻²·h⁻¹ for CR5 and R, respectively. These results indicate that Ce doping can effectively promote charge separation and improve hydrogen production efficiency by reducing resistance, accelerating charge transfer, and introducing new electronic energy levels. Our findings provide a new strategy for designing efficient photocatalysts with enhanced photoelectrochemical (PEC) water-splitting performance. Full article

Deoxynivalenol (DON) is a major mycotoxin with high toxicity that often contaminates grains, foods and feeds. The traditional approaches for DON removal are difficult to meet industry and agriculture demands due to the high stability of the DON molecule. Therefore, there is an urgent need to develop green and effective strategies for DON degradation. In this study, a batch of photocatalytic nanomaterials of cerium (Ce) doped titanium dioxide (TiO₂) were successfully prepared by sol-gel method. The catalysts were systematically characterized by XRD, HRTEM, FT-IR, UV-Vis and XPS. The catalyst 0.5Ce-TiO₂ showed superior photocatalytic activity for DON degradation in aqueous solution under ultraviolet light irradiation, better than that of traditional photocatalyst pure TiO₂, and 96% DON with initial concentration of 5.0 mg/L could be degraded in 4 h. In addition, the two possible degradation intermediate products C₅H₈O₃ and C₁₇H₁₈O₆ were identified, the photocatalytic degradation mechanism and degradation pathway were studied. The results indicate that Ce doped TiO₂ photocatalyst can be used to reduce DON effectively. Full article

Reliable and predictive in vitro assays for hazard assessments of manufactured nanomaterials (MNMs) are still limited. Specifically, exposure systems which more realistically recapitulate the physiological conditions in the lung are needed to predict pulmonary toxicity. To this end, air-liquid interface (ALI) systems have been developed in recent years which might be better suited than conventional submerged exposure assays. However, there is still a need for rigorous side-by-side comparisons of the results obtained with the two different exposure methods considering numerous parameters, such as different MNMs, cell culture models and read outs. In this study, human A549 lung epithelial cells and differentiated THP-1 macrophages were exposed under submerged conditions to two abundant types of MNMs i.e., ceria and titania nanoparticles (NPs). Membrane integrity, metabolic activity as well as pro-inflammatory responses were recorded. For comparison, A549 monocultures were also exposed at the ALI to the same MNMs. In the case of titania NPs, genotoxicity was also investigated. In general, cells were more sensitive at the ALI compared to under classical submerged conditions. Whereas ceria NPs triggered only moderate effects, titania NPs clearly initiated cytotoxicity, pro-inflammatory gene expression and genotoxicity. Interestingly, low doses of NPs deposited at the ALI were sufficient to drive adverse outcomes, as also documented in rodent experiments. Therefore, further development of ALI systems seems promising to refine, reduce or even replace acute pulmonary toxicity studies in animals. Full article

Pesticides have revolutionized the modern day of agriculture and substantially reduced crop losses. Synthetic pesticides pose a potential risk to the ecosystem and to the non-target organisms due to their persistency and bioaccumulation in the environment. In recent years, a light-mediated advanced oxidation processes (AOPs) has been adopted to resolve pesticide residue issues in the field. Among the current available semiconductors, titanium dioxide (TiO₂) is one of the most promising photocatalysts. In this study, we investigated the photocatalytic degradation of profenofos and triazophos residues in Chinese cabbage, Brassica chinensis, using a Cerium-doped nano semiconductor TiO₂ (TiO₂/Ce) under the field conditions. The results showed that the degradation efficiency of these organophosphate pesticides in B. chinensis was significantly enhanced in the presence of TiO₂/Ce. Specifically, the reactive oxygen species (ROS) contents were significantly increased in B. chinensis with TiO₂/Ce treatment, accelerating the degradation of profenofos and triazophos. Ultra-performance liquid chromatography–mass spectroscopy (UPLC-MS) analysis detected 4-bromo-2-chlorophenol and 1-phenyl-3-hydroxy-1,2,4-triazole, the major photodegradation byproducts of profenofos and triazophos, respectively. To better understand the relationship between photodegradation and the molecular structure of these organophosphate pesticides, we investigated the spatial configuration, the bond length and Mulliken atomic charge using quantum chemistry. Ab initio analysis suggests that the bonds connected by P atom of profenofos/triazophos are the initiation cleavage site for photocatalytic degradation in B. chinensis. Full article