Search Results (12)

Cephalexin is a widely used antibiotic frequently detected in hospital wastewater and aquatic environments near pharmaceutical facilities, where its persistence contributes to the spread of antibiotic resistance. Mechanically driven advanced oxidation processes, including piezocatalysis and tribocatalysis, represent sustainable alternatives for pollutant removal because they operate without external light or heat sources. In this study, ZnO catalysts with controlled morphologies were synthesized via sol–gel and mechanochemical methods using different solvents and activation times (1 and 5 h). The influence of structural characteristics, surface area, and friction conditions on catalytic performance was systematically evaluated. The results demonstrated that tribocatalytic efficiency strongly depends on stirring rate and reactor material, with PTFE systems exhibiting superior performance. Mechanochemically activated ZnO (1 h) showed the highest degradation efficiency due to optimized defect density and surface accessibility. All catalysts exhibited high stability, while radical scavenging experiments identified superoxide radicals as the primary reactive species in the degradation process. Full article

The increasing presence of antibiotics in aquatic environments is a growing concern, causing ecological and public health risks. Even low concentrations of antibiotics may lead to the development of antibiotic-resistant bacteria. The interest in building new materials that can be used as templates for removing pollutants from the environment has been growing year upon year. We review the research involving adsorption processes that occur in chitosan-based materials that are employed to remove antibiotics from water. Since covering all the antibiotics that can be found in the environment would be an overwhelming task, we concentrated our efforts on describing the studies related to the removal of tetracycline, ciprofloxacin, cephalexin, and azithromycin, which are perhaps the most ubiquitous ones. We present the chemical modifications introduced into chitosan and chitosan-based materials commonly used as antibiotic adsorbents, as well as the influence of physical chemistry conditions on these processes. In addition, we also review in silico studies that have been carried out to obtain molecular-level insights into the interactions between chitosan-based adsorbents and the four mentioned antibiotics. Particular emphasis is placed on our recent computational work regarding the adsorption of tetracycline by various chitosan-based materials. Full article

Heterogeneous Mg-Fe oxide/biochar (MgFeO@BC) nanocomposites were synthesized by a co-precipitation method and used as biochar-based catalysts to activate peroxymonosulfate (PMS) for sulfamethoxazole (SMX) removal. The optimal conditions for SMX degradation were examined as follows: pH 7.0, MgFeO@BC of 0.4 g/L, PMS concentration of 0.6 mM and SMX concentration of 10.0 mg/L at 25 ℃. In the MgFeO@BC/PMS system, the removal efficiency of SMX was 99.0% in water within 40 min under optimal conditions. In the MgFeO@BC/PMS system, the removal efficiencies of tetracycline (TC), cephalexin (CEX), ciprofloxacin (CIP), 4-chloro-3-methyl phenol (CMP) and SMX within 40 min are 95.3%, 98.4%, 98.2%, 97.5% and 99.0%, respectively. The radical quenching experiments and electron spin resonance (ESR) analysis suggested that both non-radical pathway and radical pathway advanced SMX degradation. SMX was oxidized by sulfate radicals (SO₄^•−), hydroxyl radicals (•OH) and singlet oxygen (¹O₂), and SO₄^•− acted as the main active species. MgFeO@BC exhibits a higher current density, and therefore, a higher electron migration rate and redox capacity. Due to the large number of available binding sites on the surface of MgFeO@BC and the low amount of ion leaching during the catalytic reaction, the system has good anti-interference ability and stability. Finally, the intermediates of SMX were detected. Full article

In this study, three different reusable photocatalysts containing different amino acids as a source of non-metals, including L-Arginine, L-Proline, and L-Methionine, have been synthesized for the first time. Using a kinetic study and degradation efficiency test, these visible driven photocatalysts were investigated for their photocatalytic activity in removing antibiotics, including metronidazole (MNZ) and cephalexin (CEX). The morphology, structure and optical properties of the fabricated catalysts were characterized by X-ray Powder Diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), Energy Dispersive Spectrometry (EDS)/mapping, Fourier-Transform Infrared Spectroscopy (FTIR), Photoluminescence Spectroscopy (PL) and UV-Vis Diffuse Reflectance Spectroscopy (DRS) analyses. Based on the results of the PL analysis, it was confirmed that doping TiO₂ with amino acids containing C, N, and S inhibited the recombination of induced electrons and holes. Among the three catalysts, L-Arginine-TiO₂ demonstrated the highest photocatalytic activity for antibiotic degradation, followed by L-Proline-TiO₂. According to the response surface methodology (RSM), the optimum operating conditions were a concentration of 50 mg/L MNZ, pH = 4, and catalyst concentration = 1.5 g/L under 90 min of irradiation time. At this condition, 99.9% of MNZ and 81% of TOC were removed. In addition, 97.2% of CEX and 75% TOC were eliminated at the optimum conditions of 1g/L catalyst concentration, 50 mg/L CEX concentration, at neutral pH, and after 120 min irradiation. L-Arginine (1 wt.%)-TiO₂ was tested for stability and reusability, and it showed that after five cycles, 10% of its performance had been lost. The role of reactive species in photocatalysis was identified and ^•OH had the most significant impacts on MNZ and CEX photodegradation. Antibiotic degradation efficiency was adversely affected by the presence of anions and humic acid, but this reduction was not significant for inorganic anions, as only 13% of degradation was lost. Full article

Cephalosporin enzymatic hydrolysis technology is a green technology for recovering 7-amino-3-deacetoxycephalosporanic acid (7-ADCA) from cephalosporin mother liquor. Solubility is critical for the production and purification of 7-ADCA. In this paper, the solubility of 7-ADCA and phenylglycine was measured. Solubility-temperature correlation model and solubility-pH correlation model were investigated, and Akaike information criterion (AIC) analysis was performed. The kinetic parameters of the enzymatic hydrolysis reaction of cephalexin, cefradine, and cefadroxil were determined, and the reaction rates under different substrate concentrations were measured, and the Lineweaver–Burk double-reciprocal equation was used to draw a graph. The Michaelis constants K_m/(mg/mL) were 73.98, 583.84, 38.66, V_max/(mg/mL·min) 4.20, 16.00, 1.96, respectively. The experimental results show that amphoteric compounds and buffers can prompt the reaction, low concentration of methanol promotes the reaction, while high concentration of methanol inhibits the reaction, and ethanol, isopropanol, tetrahydrofuran (THF), dimethyl sulfoxide (DMSO), ethylene glycol (EG), 1,4-dioxane all have different degrees of inhibition on the reaction speed. Finally, based on thermodynamic and kinetic studies, a process technology for the preparation of 7-ADCA by hydrolysis catalyzed of cephalexin was developed. It was confirmed that the proposed process route of preferential removal of phenylglycine by elution and/or cooling crystallization was reasonable and effective. The 7-ADCA crystal products obtained by crystallization were characterized by PXRD, thermal analysis, infrared, electron microscope, and high-performance liquid chromatography (HPLC). Full article

Increasing quantities of pharmaceutical pollutants have been found in aquatic ecosystems. The treatment of pharmaceutical pollutants has been a major task that people have been committed to in recent years. The removal of pharmaceutical pollutants can be achieved by adsorption and advanced oxidation processes (AOPs). Compared with other carbon materials, biochar has a strong adsorption capacity and persulfate activation ability, and more importantly, biochar is cheap and easy to obtain; thus, it has higher economic benefits. This study firstly reviews the application of biochar in the removal of drugs (tetracycline (TC), sulfamethoxazole (SMX), acetaminophen (ACT), cephalexin (CPX), levofloxacin (LEV), etc.) through adsorption and persulfate-based AOPs. In addition, we summarize the adsorption mechanism of biochar for various pharmaceutical pollutants and the main attack sites on different pharmaceutical pollutants in persulfate-based AOPs catalyzed by biochar. Finally, the challenges and prospects of biochar with respect to the removal of pharmaceutical pollutants are put forward. Full article

Cephalexin (CFX) residues in the environment represent a major threat to human health worldwide. Herein we investigate the use of novel approaches in deep learning in order to understand the mechanisms and optimal conditions for the sorption of cephalexin in water onto an acidic pretreated jackfruit peel adsorbent (APJPA). The interaction between the initial concentration of CFX (10–50 mg/100 mL), APJAP dosage (3–10 mg/100 mL), time (10–60 min), and the pH (4–9), was simulated using the one-factor-at-a-time method. APJPA was characterized by FESEM images showing that APJPA exhibits a smooth surface devoid of pores. FTIR spectra confirmed the presence of -C-O, C–H, C=C, and -COOH bonds within the APJPA. Maximum removal was recorded with 6.5 mg/100 mL of APJAP dosage, pH 6.5, after 35 min and with 25 mg/100 mL of CFX, at which the predicted and actual adsorption were 96.08 and 98.25%, respectively. The simulation results show that the dosage of APJAP exhibits a high degree of influence on the maximum adsorption of CFX removal (100%) between 2 and 8 mg dose/100 mL. The highest adsorption capacity of APJAP was 384.62 mg CFX/g. The simulation for the effect of pH determined that the best pH for the CFX adsorption lies between pH 5 and 8. Full article

One of the most serious effects of micropollutants in the environment is biological magnification, which causes adverse effects on humans and the ecosystem. Among all of the micro-pollutants, antibiotics are commonly present in the aquatic environment due to their wide use in treating or preventing various diseases and infections for humans, plants, and animals. Therefore, an aluminum-based electrocoagulation unit has been used in this study to remove cephalexin antibiotics, as a model of the antibiotics, from water. Computational and statistical models were used to optimize the effects of key parameters on the electrochemical removal of cephalexin, including the initial cephalexin concentration (15–55 mg/L), initial pH (3–11), electrolysis time (20–40 min), and electrode type (insulated and non-insulated). The response surface methodology-central composite design (RSM-CCD) was used to investigate the dependency of the studied variables, while the artificial neural network (ANN) and adaptive neuro-fuzzy inference system (ANFIS) methods were applied for predicting the experimental training data. The results showed that the best experimental and predicted removals of cephalexin (CEX) were 88.21% and 93.87%, respectively, which were obtained at a pH of 6.14 and electrolysis time of 34.26 min. The results also showed that the ANFIS model predicts and interprets the experimental results better than the ANN and RSM-CCD models. Sensitivity analysis using the Garson method showed the comparative significance of the variables as follows: pH (30%) > electrode type (27%) > initial CEX concentration (24%) > electrolysis time (19%). Full article

This work describes the hydroxyapatite nanoparticle (HAP) preparation from eggshell waste and their application as an adsorbent for Cephalexin (Ceph) antibiotic removal from aqueous solutions. Chemical precipitation with phosphoric acid was used to evaluate the feasibility of calcium oxide for HAP preparation. The structural properties of HAP were characterized by X-ray diffraction, which revealed the formation of the hydroxyapatite crystalline phase formation. In addition, transmitting electron spectroscopy showed an irregular shape with a variation in size. The impact of various experimental conditions on the removal efficiency such as the solution’s pH, contact time, HAP mass, solution temperature, and Ceph concentration were studied. Experimental data showed that HAP could remove most Ceph species from aqueous solutions within 1 h at pH = 7 with 70.70% adsorption efficiency utilizing 50 mg of the HAP. The removal process of Ceph species by HAP was kinetically investigated using various kinetic models, and the results showed the suitability of the pseudo-second-order kinetic model for the adsorption process description. Moreover, the removal process was thermodynamically investigated; the results showed that the removal was spontaneous endothermic and related to the randomness increase. The data confirmed that HAP had high efficiency in removing Ceph antibiotics from an aqueous solution. Full article

Pharmaceuticals and dyes are a very important part of the nonbiodegradable or hard biodegradable substances present in wastewater. Microorganisms are already known to be effective biosorbents, but the use of free microbial cells involves difficulties in their separation from effluents and limits their application in wastewater treatment. Thus, this study aimed to develop biosorbents by immobilizing Saccharomyces cerevisiae, Saccharomyces pastorianus and Saccharomyces pastorianus residual biomass on natural polymers (alginate and chitosan) and to evaluate the biosorptive potential for removal of pharmaceuticals and dyes from water. Six types of biosorbents were synthesized and characterized by Scanning Electron Microscopy and Fourier Transform Infrared Spectroscopy techniques and their biosorptive capacities for three drugs (cephalexin, rifampicin, ethacridine lactate) and two dyes (orange II and indigo carmine) were evaluated. The obtained results show that the removal efficiency depends on the polymer type used for the immobilization. In case of alginate the removal efficiency is between 40.05% and 96.41% for drugs and between 27.83% and 58.29% for dyes, while in the case of chitosan it is between 40.83% and 77.92% for drugs and between 17.17% and 44.77% for dyes. In general, the synthesized biosorbents proved to be promising for the removal of drugs and dyes from aqueous solutions. Full article

Cephalexin (CPX) is recognized as a water pollutant, and it has been listed in a number of countries with a risk factor greater than one. Herein, the present work focused on the synthesis, characterization and biosorption capacity evaluation of Saccharomyces cerevisiae immobilized in calcium alginate as a biosorbent to remove CPX from aqueous solutions. Biosorbent was characterized by SEM and FTIR techniques. Batch biosorption experiments were conducted in order to evaluate the effect of the initial pH, biosorbent dose and CPX initial concentration. The removal efficiency, in considered optimal conditions (pH = 4, CPX initial concentration = 30 mg/L, biosorbent dose = 1 g/L) was 86.23%. CPX biosorption was found to follow the pseudo–second-order kinetics. The equilibrium biosorption data were a good fit for the Langmuir model with correlation coefficient of 0.9814 and maximum biosorption capacity was 94.34 mg/g. This study showed that the synthesized biosorbent by immobilization technique is a low-cost one, easy to obtain and handle, eco-friendly, with high feasibility to remove CPX antibiotic from aqueous solution. The findings of this study indicate that the biosorbents based on microorganisms immobilized on natural polymers have the potential to be applied in the treatment of wastewater. Full article

This study aimed to understand the adsorption process of cephalexin (CPX) from aqueous solution by a biochar produced from the fiber residue of palm oil. Scanning electron microscopy, Fourier transform infrared spectroscopy, Boehm titration, and the point of zero charge were used to characterize the morphology and surface functional groups of the adsorbent. Batch tests were carried out to evaluate the effects of the solution pH, temperature, and antibiotic structure. The adsorption behavior followed the Langmuir model and pseudo-second-order model with a maximum CPX adsorption capacity of 57.47 mg g⁻¹. Tests on the thermodynamic behavior suggested that chemisorption occurs with an activation energy of 91.6 kJ mol⁻¹ through a spontaneous endothermic process. Electrostatic interactions and hydrogen bonding represent the most likely adsorption mechanisms, although π–π interactions also appear to contribute. Finally, the CPX removal efficiency of the adsorbent was evaluated for synthetic matrices of municipal wastewater and urine. Promising results were obtained, indicating that this adsorbent can potentially be applied to purifying wastewater that contains trace antibiotics. Full article