Search Results (8)

Cutting inserts made of ceramic materials are used in rough machining processes of Inconel 718. This article compares sintered carbide S205 inserts with 6160 ceramic inserts after finish turning of Inconel 718 with a hardness of 45 HRC. The evaluation focused on insert wear, surface topography and changes in cutting edge radius. The results show differences in the wear of S205 and 6160 inserts. S205 inserts characterize the formation of buildup on the rake face, while 6160 inserts tend to form buildup on the flank face. Furthermore, ceramic 6160 inserts are more prone to notch wear. Surface topography analysis revealed the formation of individual high peaks on surfaces machined with ceramic inserts. The Sa parameter for all cutting conditions studied did not exceed 0.45 µm. Full article

This paper features a comprehensive analysis of various multiscale selforganization processes that occur during cutting. A thorough study of entropy production during friction has uncovered several channels of its reduction that can be achieved by various selforganization processes. These processes are (1) self-organization during physical vapor deposition PVD coating deposition on the cutting tool substrates; (2) tribofilm formation caused by interactions with the environment during operation, which consist of the following compounds: thermal barriers; Magnéli phase tribo-oxides with metallic properties at elevated temperatures, tribo-oxides that transform into a liquid phase at operating temperatures, and mixed action tribo-oxides that serve as thermal barriers/lubricants, and (3) multiscale selforganization processes that occur on the surface of the tool during cutting, which include chip formation, the generation of adhesive layers, and the buildup edge formation. In-depth knowledge of these processes can be used to significantly increase the wear resistance of the coated cutting tools. This can be achieved by the application of the latest generation of complex adaptive surface-engineered systems represented by several state-of-the-art adaptive nano-multilayer PVD coatings, as well as high entropy alloy coatings (HEAC). Full article

The present study was conducted on the machinability of 396 alloy (containing approximately 11% Si) and B319.2 alloy mainly to emphasize the effects of Fe-intermetallics, i.e., α-Fe, β-Fe, and sludge. The results demonstrate that the presence of sludge in the form of hard spots has a significant effect on cutting forces and tool life, in that it decreases drill life by 50% compared to the base alloy. The formation of the α-Fe phase in the M1 base alloy has a beneficial effect on tool life in that this alloy produces the highest number of holes drilled compared to alloys containing sludge or β-Fe; this result may be explained by the fact that the formation of the α-Fe intermetallic, with its rounded Chinese script morphology and its presence within α-Al dendrites, is expected to improve matrix homogeneity via hardening of the soft α-Al dendrites. Increasing the Fe-content from 0.5% to 1% in the 396-T6 alloy containing 0.5% Mn produces a distinct improvement in alloy machinability in terms of cutting force and tool life. The addition of Fe and/or Mn appears to have no discernible effect on the build-up edge area (BUE) and chip shape. Full article

This paper presents experimental investigations of various interrelated multi-scale cyclic and temporal processes that occur on the frictional surface under severe tribological conditions during cutting with buildup edge formation. The results of the finite element modeling of the stress/temperature profiles on the friction surface are laid out. This study was performed on a multilayer coating with the top alumina ceramic layer deposited by CVD (chemical vapor deposition) on a WC/Co carbide substrate. A detailed analysis of the wear process was conducted by 3D wear evaluation, scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS) and electron backscattered diffraction (EBSD), as well as X-ray photoelectron spectroscopy (XPS) methods. The following cyclic phenomena were observed on the surface of the tribo-system during the experiments: a repetitive formation and breakage of buildups (a self-organized critical process) and a periodical increase and decrease in the amount of thermal barrier tribo-films with a sapphire structure (which is a self-organization process). These two processes are interrelated with the accompanying progression of cratering, eventually resulting in the catastrophic failure of the entire tribo-system. Full article

A new family of physical vapor deposited (PVD) coatings is presented in this paper. These coatings are deposited by a superfine cathode (SFC) using the arc method. They combine a smooth surface, high hardness, and low residual stresses. This allows the production of PVD coatings as thick as 15 µm. In some applications, in particular for machining of such hard to cut material as compacted graphite iron (CGI), such coatings have shown better tool life compared to the conventional PVD coatings that have a lower thickness in the range of up to 5 μm. Finite element modeling of the temperature/stress profiles was done for the SFC coatings to present the temperature/stress profiles during cutting. Comprehensive characterization of the coatings was performed using XRD, TEM, SEM/EDS studies, nano-hardness, nano-impact measurements, and residual stress measurements. Application of the coating with this set of characteristics reduces the intensity of buildup edge formation during turning of CGI, leading to longer tool life. Optimization of the TiAlN-based coatings composition (Ti/Al ratio), architecture (mono vs. multilayer), and thickness were performed. Application of the optimized coating resulted in a 40–60% improvement in the cutting tool life under finishing turning of CGI. Full article

Tribological phenomena and tool wear mechanisms during machining of hard-to-cut TiAl6V4 aerospace alloy have been investigated in detail. Since cutting tool wear is directly affected by tribological phenomena occurring between the surfaces of the workpiece and the cutting tool, the performance of the cutting tool is strongly associated with the conditions of the machining process. The present work shows the effect of different machining conditions on the tribological and wear performance of TiB₂-coated cutting tools compared to uncoated carbide tools. FEM modeling of the temperature profile on the friction surface was performed for wet machining conditions under varying cutting parameters. Comprehensive characterization of the TiB₂ coated vs. uncoated cutting tool wear performance was made using optical 3D imaging, SEM/EDX and XPS methods respectively. The results obtained were linked to the FEM modeling. The studies carried out show that during machining of the TiAl6V4 alloy, the efficiency of the TiB₂ coating application for carbide cutting tools strongly depends on cutting conditions. The TiB₂ coating is very efficient under roughing at low speeds (with strong buildup edge formation). In contrast, it shows similar wear performance to the uncoated tool under finishing operations at higher cutting speeds when cratering wear predominates. Full article

In this paper, we will develop a strategy for controlling the self-organized critical process using the example of extreme tribological conditions caused by intensive build-up edge (BUE) formation that take place during machining of hard-to-cut austentic superduplex stainless steel SDSS UNS32750. From a tribological viewpoint, machining of this material involves intensive seizure and build-up edge formation at the tool/chip interface, which can result in catastrophic tool failure. Built-up edge is considered to be a very damaging process in the system. The periodical breakage of the build-ups may eventually result in tool tip breakage and, thereby, lead to a catastrophe (complete loss of workability) in the system. The dynamic process of build-up edge formation is similar to an avalanche. It is governed by stick-slip phenomenon during friction and associated with the self-organized critical process. Investigation of wear patterns on the frictional surfaces of cutting tools using Scanning Electron Microscope (SEM), combined with chip undersurface characterization and frictional (cutting) force analyses, confirms this hypothesis. The control of self-organized criticality is accomplished through application of a nano-multilayer TiAl60CrSiYN/TiAlCrN thin film Physical Vapor Deposition (PVD) coating containing elevated aluminum content on a cemented carbide tool. The suggested coating enhanced the formation of protective nano-scale tribo-films on the friction surface under operation. Moreover, machining process optimization contributed to further enhancement of this beneficial process, as evidenced by X-ray Photoelectron Spectroscopy (XPS) studies of tribo-films. This resulted in a reduction of the scale of the build ups leading to overall wear performance improvement. A new thermodynamic analysis is proposed concerning entropy production during friction in machining with buildup edge formation. This model is able to predict various phenomena and shows a good agreement with experimental results. In the presented research we demonstrated a novel experimental approach for controlling self-organized criticality using an example of the machining with buildup edge formation, which is similar to avalanches. This was done through enhanced adaptive performance of the surface engineered tribo-system, in the aim of reducing the scale and frequency of the avalanches. Full article

This manuscript summarizes the failure mechanisms found in inorganic fullerene-type tungsten disulfide (IF-WS₂) nanoparticles treated with diverse pressure loading methods. The approaches utilized to induce failure included: the use of an ultrasonic horn, the buildup of high pressures inside a shock tube which created a shock wave that propagated and impinged in the sample, and impact with military rounds. After treatment, samples were characterized using electron microscopy, powder X-ray diffraction, energy dispersive X-ray spectroscopy, and surface area analysis. The microstructural changes observed in the IF-WS₂ particulates as a consequence of the treatments could be categorized in two distinct fracture modes. The most commonly observed was the formation of a crack at the particles surface followed by a phase transformation from the 3D cage-like structures into the 2D layered polymorphs, with subsequent agglomeration of the plate-like sheets to produce larger particle sizes. The secondary mechanism identified was the incipient delamination of IF-WS₂. We encountered evidence that the IF-WS₂ structure collapse initiated in all cases at the edges and vertices of the polyhedral particles, which acted as stress concentrators, independent of the load application mode or its duration. Full article