Search Results (2,918)

Background: The interaction between human immunoglobulin G (IgG)1 Fc and the Fc gamma receptor (FcγR) IIIa/CD16a elicits protective immune responses. Antibody N-glycosylation stabilizes the FcγR-binding interface and is thus essential for interaction with wildtype IgG1 Fc. Furthermore, the N-glycan introduces substantial compositional and functional heterogeneity, with distinct glycoforms providing different affinities and discrete responses in vivo. Accordingly, various engineering endeavors to improve antibody binding strive to boost the therapeutic efficacy of monoclonal antibodies but do not directly address compositional heterogeneity. Objective: Here, we describe a previously unexplored approach to engineer IgG1 Fc. We eliminated carbohydrate heterogeneity by removing the N-glycan but stabilizing the FcγR-binding interface with disulfide bonds. Conclusions: These newly generated Fc domains served as a starting point for protein engineering through yeast surface display to enhance receptor-binding affinity. We recovered Fc variants from this approach that demonstrated FcγRIIIa binding affinities comparable to the starting sequence and thus serve as a proof-of-principle for this strategy. Full article

Under low-temperature and humid conditions, icing on airfoil surfaces, such as wind turbine blades, deteriorates the aerodynamic performance and decreases the power generation efficiency. To shorten the de-icing time and reduce the de-icing energy consumption, an ultrasonic de-icing method was used by coupling the longitudinal vibration of a piezoelectric transducer and the bending deformation of an iced plate. The simulation method was used to investigate the distributions and the variations of the stresses at the bond interface. An experimental system for ultrasonic de-icing tests was developed and built, and the de-icing experiments were carried out. The experimental results showed that the present ultrasonic de-icing method had a short de-icing time and low de-icing energy consumption, and the de-icing processes agreed with the simulation results. In the present research, the ice layer with a diameter of 20 mm was removed in the shortest de-icing time and the lowest energy consumption because its diameter was close to that of the transducer, which resulted in the highest shear stress at the bond interface. The present study provides theoretical and experimental foundations for deep research on the surface anti- and de-icing method with ultrasonic techniques. Full article

Per- and polyfluoroalkyl substances (PFASs) are persistent environmental contaminants whose mobility in soil and groundwater is strongly controlled by adsorption and desorption processes. In saturated clay-rich soils, these processes are complex because PFASs interact with hydrated mineral surfaces, organic matter, metal oxides, exchangeable cations, and pore-water constituents. This review synthesizes the current literature on PFAS adsorption and desorption in saturated soils, with an emphasis on clay mineralogy, mineral–water interfaces, pore-water chemistry, and electrochemical double layer (EDL) effects. PFAS retention is influenced by molecular properties such as chain length, functional head group, and charge state, as well as soil properties such as organic carbon content, clay mineral type, surface charge, cation exchange capacity, and Fe/Al oxide content. Longer-chain PFASs and sulfonate-based compounds generally show stronger retention, while shorter-chain PFASs tend to remain more mobile. This review focuses particularly on how an EDL affects PFAS behavior in saturated clay systems. Unlike dry clay surfaces, saturated clay surfaces are covered by structured water, exchangeable ions, and diffuse counterion layers. These hydrated interfacial conditions influence how closely anionic PFASs can approach negatively charged clay surfaces, how dissolved cations reduce electrostatic repulsion or promote cation-mediated binding, and how effectively short-range interactions such as hydrophobic association, van der Waals forces, hydrogen bonding, and surface association contribute to adsorption. Desorption is also emphasized because adsorption does not necessarily represent permanent immobilization. Changes in pH, ionic strength, cation composition, dissolved organic matter, or competing solutes can weaken retention and promote PFAS release. Overall, PFAS mobility in saturated clay-rich soils should be interpreted as a coupled interfacial process rather than simple partitioning to soil solids. Future work should better connect molecular-scale mechanisms, EDL behavior, adsorption–desorption experiments, and saturated transport studies to improve predictions of PFAS retention and long-term groundwater release. Full article

To understand glycan–protein interactions at biological interfaces, designing surfaces modified with structurally controlled glycans is highly important. In particular, naturally occurring glycosaminoglycans (GAGs) possess periodic sugar arrangements that play important roles in protein recognition, highlighting the need for the development of periodic glycopolymer model systems that can serve as GAG mimics for quantitative interaction analysis. In this study, sequence-controlled periodic glycopolymers were synthesized by reversible addition–fragmentation chain-transfer (RAFT) polymerization and immobilized onto gold surfaces to construct glycan-modified interfaces. The synthesized material was a terminally functionalized periodic glycopolymer with the most basic structure, consisting of alternating maltose-containing vinyl ether (MalVE) units and ethyl maleimide (EtMI) units, with a trithiocarbonate group at the ω-terminal. This trithiocarbonate group was converted to a thiol group for immobilization through Au–S bond formation. Structural characterization by ¹H NMR spectroscopy, size exclusion chromatography (SEC), MALDI-TOF mass spectrometry, and UV–vis spectroscopy confirmed the structure as designed. Quartz crystal microbalance (QCM) measurements verified the stable immobilization of thiol-terminated periodic glycopolymers on the gold surface, and allowed for estimation of graft density and quantitative analysis of glycan-protein interactions at the modified interface. The periodic glycopolymer-modified surfaces exhibited selective binding behavior toward concanavalin A (ConA) compared to bovine serum albumin (BSA), with apparent binding constants on the order of 10⁶–10⁷ L mol⁻¹. This enhanced binding behavior indicated that specific and multivalent interactions with proteins also occurred at periodic pendant maltose residues along the main chain. These results demonstrate that the gold surface modified with end-functional periodic glycopolymers synthesized by RAFT polymerization provides a versatile platform for quantitative analysis of glycan-protein interactions and suggests potential applications for periodic glycopolymers as functional materials. Full article

Aim: The aim of this study was to comparatively evaluate the shear bond strengths between different calcium silicate-based biomaterials and glass ionomer-based restorative materials. Materials and Methods: In this in vitro study, a total of 96 acrylic blocks were prepared, each containing a standardized cylindrical cavity measuring 4 mm in diameter and 2 mm in depth. Four different calcium silicate-based biomaterials (ProRoot MTA, Biodentine, TheraCal LC, and MTA BioRep) were placed into the cavities according to the manufacturers’ instructions. Three different glass ionomer restorative materials (Fuji II LC, Equia Forte HT, and Riva Self Cure) were then applied onto the biomaterial surfaces using molds measuring 2 mm in diameter and 2 mm in height, resulting in 12 experimental groups (n = 8). After storage at 37 °C for 24 h, the shear bond strengths were measured using a universal testing machine. The data were analyzed using the Kruskal–Wallis and Mann–Whitney U tests with Bonferroni correction (p < 0.05). Results: The highest bond strength was observed in the TheraCal LC–Fuji II LC combination, whereas the lowest value was obtained in the MTA BioRep–Equia Forte HT group. Both the type of biomaterial and type of glass ionomer cement had a statistically significant effect on the bond strength (p < 0.05). Conclusions: The combination of calcium silicate-based biomaterial and glass ionomer-based restorative material influenced the early shear bond strength. These findings suggest that material selection may play an important role in early bonding behavior at the biomaterial–restorative material interface. Full article

An Al₂O₃/AlN stack deposited via Atomic Layer Deposition (ALD) methods as a gate insulator for silicon carbide (4H-SiC) has been investigated, focusing on the effects of different Al₂O₃ deposition processes on the nitride layer. In particular, dielectric stacks, consisting of a 10 nm AlN interface (001)-oriented layer directly grown on a 4H–SiC substrate and in 20 nm of additional amorphous Al₂O₃ layers were synthesized in sequential deposition runs by thermal ALD (T-ALD) or plasma-enhanced ALD (PEALD) methods. The evolution of the phenomena occurring at the Al₂O₃/AlN interfaces has been established by in situ ellipsometry measurements. Strong effects of the oxygen plasma because of the O-Al-N bond formation have been clearly observed and corroborated by ex situ structural and electrical characterizations, especially in the case of the plasma-enhanced Al₂O₃ process. In particular, the Al₂O₃/AlN bilayer grown by the Al₂O₃ T-ALD method exhibited good insulating behavior and an 8.7-high dielectric constant was measured. By contrast, the Al₂O₃/AlN bilayer grown by the Al₂O₃ PEALD method demonstrated poor insulating properties. Full article

3D-printed continuous carbon fiber-reinforced polylactic acid (CF/PLA) composites combine the high load-bearing capability of continuous fibers with the structural design freedom of additive manufacturing, showing broad application prospects in lightweight complex structures. However, the chemically inert surface of carbon fibers and their insufficient interfacial compatibility with the PLA matrix lead to inefficient interfacial load transfer, thereby limiting the mechanical performance of the composites. In this study, a waterborne polyurethane (WPU)-based sizing treatment was applied to carbon fibers to enhance the fiber–matrix interface of 3D-printed continuous CF/PLA composites. The WPU sizing layer increased fiber-bundle cohesion and introduced a transition region between CF and PLA through possible hydrogen bonding, dipolar interactions, and physical adhesion. When the nominal WPU concentration was 5 wt%, the apparent interfacial shear strength reached 1.31 MPa, representing an improvement of approximately 65% compared with ACF/PLA. The three-point flexural strength reached 69.76 MPa, which was 55.3% higher than that of the ACF/PLA composite. These results indicate that WPU sizing is an effective and scalable interfacial regulation strategy for improving the mechanical properties of 3D-printed continuous CF/PLA composites. Full article

Although the long-term behavior of ground anchors depends fundamentally on interfacial behavior, the independent effect of the strand–grout interface on load loss has not been comprehensively investigated. This study establishes a physical model testing method that isolates the strand–grout interface and systematically investigates both short-term and long-term load loss behavior. Pull-out tests and long-term monitoring tests were conducted using grout uniaxial compressive strength ($q_u$ = 18–30 MPa) and bond length ($L_b$ = 900–1500 mm) as primary design variables. Long-term monitoring confirmed that prestress loss at the strand–grout interface is induced by the progressive pull-out displacement of the strand over time, following a logarithmic decay pattern. The load reduction coefficient n was significantly more sensitive to $L_b$ than to $q_u$; n increased sharply from 0.015 to 0.069 as $L_b$ decreased. Anchors with insufficient bond length exhibited secondary load reduction behavior that disrupted the stable log-linear decay, posing significant risk to long-term performance. Based on RMSE analysis of the fitted logarithmic model, a minimum monitoring period of approximately 50 days is recommended for reliable long-term prediction when bond length is adequate. These findings identify $q_u$ and $L_b$ as the governing parameters, providing a quantitative basis for optimizing prestress design and enhancing the long-term reliability of anchor systems. Full article

This work presents an enhanced photomechanical optical sensor inspired by our previously reported bio-inspired uncooled infrared detector. Performance improvement is achieved by strengthening the interfacial bond between the photothermal dendrite—polydopamine nanoparticle (PDA NP)/polydimethylsiloxane (PDMS) composite—and the piezoresistive laser-induced nanocarbon film, with a flexible PDMS substrate that provides both thermal insulation and mechanical stability. The resulting sensor exhibits a responsivity of 51.6 W⁻¹ under 808 nm irradiation, an order-of-magnitude enhancement over the unmodified device. Wavelength-dependent characterization (455–1550 nm) shows responsivity decreasing from 93.1 W⁻¹ at 455 nm to 14.4 W⁻¹ at 1550 nm, with response times on the order of seconds across this range. Extending this trend into the longer-wavelength region of blackbody radiation, the mechanism transitions to a predominantly bolometric mode. The device also demonstrates stable detection of several hundred microwatts and robust durability at 455 nm. These results validate interface engineering strategy as a viable pathway toward high-performance uncooled optical detection, advancing bio-inspired detectors from functional mimicry toward an application-ready platform. These findings confirm PDA NPs as effective photothermal converters primarily at shorter wavelengths, while the wavelength-dependent response suggests future tailoring of spectral sensitivity using long-wavelength-absorbing materials. Full article

Modern prosthetic dentistry has been significantly reshaped by adhesive dentistry, CAD/CAM technologies, and advanced ceramic materials, leading to the development of minimally invasive all-ceramic restorative approaches. However, the longevity of the adhesive interface is fundamental to the long-term effectiveness of these restorations. With a focus on bond durability and clinical performance, this narrative review aims to evaluate modern adhesive strategies, tooth preparation requirements, and cementation techniques in all-ceramic minimally invasive restorations. Methods: A narrative review of the literature was performed using Google Scholar, Web of Science, and PubMed/MEDLINE databases. Publications from 2000 to 2026 were analysed. In vitro research, narrative reviews, and systematic reviews related to adhesive systems, resin cements, CAD/CAM materials, and minimally invasive prosthodontic principles were the core subjects of the research. Results: The findings indicate that material selection, surface conditioning techniques, and cementation methods have a significant impact on the clinical effectiveness of all-ceramic restorations. Retention and marginal sealing are greatly enhanced by resin-based adhesive systems. Nevertheless, hydrolytic degradation, procedure sensitivity, and substrate-related factors remain a challenge to the adhesive interface. Advances in CAD/CAM and ultra-conservative designs, like occlusal veneers and partial-coverage restorations, have increased treatment alternatives while ensuring acceptable functional and aesthetic results. Conclusions: Minimally invasive all-ceramic restorations represent a conservative and clinically effective treatment approach in modern prosthodontics. Their long-term performance is primarily dependent on adhesive interface stability and adherence to evidence-based clinical protocols. Continued developments in adhesive materials and ceramic systems are expected to improve bond durability and broaden clinical indications. Full article

Ferroelectric (FE) diodes configured in the metal–ferroelectric–metal (MIFM) structure are promising candidates for non-volatile memory. While recent studies emphasized bulk FE properties, interfacial characteristics have not been carefully considered. In this work, we investigate the HfO₂/Al_0.8Sc_0.2N interface by examining its impact on switching and rectifying characteristics in MIFM FE diodes with variable HfO₂ thicknesses (2/4/6 nm). Electrical characterization reveal that the increased HfO₂ thickness raises the coercive field (E_C) due to enhanced electrostatic effects and progressive interfacial oxidation from Sc-N to Sc-O bonds. This resulting oxygen substitutional defect (O_N) which may contribute to domain-wall pinning and reduced rectifying efficiency. Cycling tests clarify operating regime-dependent phenomena, including O_N redistribution-induced wake-up and eventual breakdown. Moreover, enhanced retention is observed after pre-cycling, originating from the stabilization of the interfacial defects rather than bulk properties. These findings underscore that E_C and device reliability are likely influenced by interfacial engineering, which is critical for the reliable operation of AlScN-based FE diodes. Full article

Circular tunnel linings are geometrically symmetric structures, whereas non-uniform external pressure and different steel–concrete layer arrangements may induce asymmetric stress redistribution. To distinguish the axisymmetric response from the asymmetric harmonic response, this study develops an analytical solution for a two-layer corrugated steel–concrete composite tunnel lining subjected to equivalent external pressure. The concrete layer is modeled as an isotropic elastic material, while the corrugated steel layer is represented as an equivalent cylindrically orthotropic material. The governing equations are formulated in polar coordinates under plane-strain conditions, and the solution is obtained by superposing the axisymmetric component and the harmonic component. Perfect bonding is assumed at the steel–concrete interface, where displacement, radial stress, and shear stress are continuous. The proposed analytical solution is verified using finite element models for three cases: a single-layer homogeneous lining under uniform pressure, a two-layer composite lining under uniform pressure, and a two-layer composite lining under non-uniform pressure. The analytical and finite element results show good agreement, confirming the mathematical consistency and implementation accuracy of the proposed formulation. Based on the verified solution, the effects of layer arrangement, corrugated steel stiffness ratio, and burial depth are investigated. The results show that the corrugated steel layer carries the dominant hoop stress in both layer arrangements. The inner corrugated steel arrangement may be more relevant to internal strengthening of existing tunnels, whereas the outer corrugated steel arrangement provides a useful reference for new composite linings dominated by external ground pressure. Increasing the stiffness ratio transfers more hoop stress to the steel layer and reduces the elastic stress and displacement responses of the concrete layer, although improvement becomes less significant at large stiffness ratios. Increasing burial depth mainly amplifies the response magnitude without changing the overall symmetry pattern. The proposed solution provides a closed-form benchmark for evaluating symmetry-related stress redistribution in corrugated steel–concrete composite tunnel linings within the linear-elastic range. Full article

Lead sulfide quantum dots (PbS QDs), as a functional-layer coating, enable non-volatile integration and neuromorphic computing in memristive structures to address the von Neumann bottleneck. Herein, the dual-interface mechanism of PbS QDs in the memristor film structure is reviewed. First, the local electric field enhancement effect generates tip electrode-like structures in the coating film through QD-mediated spatial charge gradients, thereby enabling precise control over the nucleation and growth of conductive filaments (CFs). As a result, the consistency of switching voltages and the thermal stability at elevated temperatures are significantly improved. Conversely, the anion reservoir effect exploits surface dangling bonds on QDs to efficiently capture anions from the dielectric layer, thereby synergistically regulating vacancy migration kinetics. This process enables zero-initialization behavior and ultra-low-power operation. In addition, the spatial distribution design and density modulation of QDs further reinforce both mechanisms. The structural optimization of QD/dielectric interface engineering can simultaneously improve cycling endurance and resistive switching uniformity. Furthermore, modification of QD surface chemistry through ligand decoration and passivation suppresses the stochasticity of ionic diffusion while improving the linearity of synaptic weight updates. This interfacial engineering strategy utilizing QDs as coating films advances the development of high-performance photonic–electronic systems for memory–computing convergence. Full article

Achieving efficient demulsification of water-in-heavy oil (W/HO) emulsions remains a critical issue that urgently needs to be addressed in the heavy oil industry. Despite being a new generation of green demulsification materials, magnetic carbon nanoparticles still suffer from low demulsification efficiency when applied to water-in-heavy oil emulsions. Herein, polyethyleneimine-modified magnetic carbon nanoparticles (P-MCNs) were successfully prepared via a surface functionalization strategy. The demulsification performance of P-MCN in water-in-heavy oil (W/HO) emulsions was evaluated via the standard bottle test. The results demonstrated that P-MCN (500 ppm) achieved effective water removal within 60 min at 50 °C. Microscopic visualization characterization revealed that the efficient water removal from W/HO emulsions by P-MCN is attributed to its high interfacial activity. Specifically, P-MCN can rapidly migrate to the heavy oil–water interface and effectively disrupt the interfacial film through electrostatic interactions and hydrogen bonding, thereby achieving efficient demulsification of W/HO emulsions. This study provides a solid theoretical foundation for the further development of magnetic carbon nanoparticles with higher demulsification efficiency for applications in the petroleum industry. Full article

The design of the overall thickness and thickness ratio in multilayered composites is vital because it affects interfacial microstructures and mechanical properties. These elements are significant in the application of multilayered composites in diverse scenarios. This study systematically investigated the interfacial microstructure, mechanical properties, and fracture mechanisms of Cu/Al/Cu trilayered composites with varying overall thicknesses and copper thickness ratios. The microstructure results showed that the distribution and thickness of intermetallic compounds (IMCs) at the Cu/Al interface changed significantly with different thickness designs. As the Cu thickness ratio increased from 20% to 35%, the intermetallic layer transitioned from a continuous structure to a fragmented one in both the 1 mm and 2 mm composites. Additionally, the bonding mechanism evolved from primarily metallurgical bonding to a combination of metallurgical and mechanical bonding. In the 4 mm composite with a 35% Cu thickness ratio, the interfacial intermetallic layer comprised three sublayers identified as Al₄Cu₉, AlCu, and Al₂Cu. Tensile results indicated that increasing the Cu thickness ratio markedly enhanced strength and ductility: the 1 mm composite showed increases of 22.3% in ultimate tensile strength and 70.9% in elongation, while the 2 mm composite exhibited increases of 32.4% and 38.7%, respectively. In contrast, increasing the overall thickness had only a limited effect. Fractography revealed ductile fracture features in both the Al and Cu layers, characterized by more compact interfaces, deeper dimples, and more pronounced tear ridges at higher Cu thickness ratios. These findings demonstrate that optimizing the Cu thickness ratio is an effective strategy for enhancing interfacial bonding strength and overall mechanical performance in Cu/Al/Cu composites. Full article