Search Results (18)

In this paper we present a detailed study of bonded knots and their related structures, integrating recent developments into a single framework. Bonded knots are classical knots endowed with embedded bonding arcs modeling physical or chemical bonds. We consider bonded knots in three categories (long, standard, and tight) according to the type of bonds, and in two categories, topological vertex and rigid vertex, according to the allowed isotopy moves, and we define invariants for each category. We then develop the theory of bonded braids, the algebraic counterpart of bonded knots. We define the bonded braid monoid, with its generators and relations, and formulate the analogues of the Alexander and Markov theorems for bonded braids in the form of L-equivalence for bonded braids. Next, we introduce enhanced bonded knots and braids, incorporating two types of bonds (attracting and repelling) corresponding to different interactions. We define the enhanced bonded braid group and show how the bonded braid monoid embeds into this group. These models capture the topology of chains with inter and intra-chain bonds and suggest new invariants for classifying biological macromolecules. Full article

Background: Despite the large variety of retainer wires available, no studies could be found comparing the micromechanical properties and surface roughness of different retainer wires. Such characteristics affect the survival of the fixed retainer in terms of both fracture resistance and resistance to debonding from the tooth. Therefore, the aim of the present study was to examine and compare those characteristics in popular retainer wires. Methods: six different popular orthodontic retainer wires were subjected to instrumental indentation based on the Oliver and Pharr method. The geometric surface structure was analysed using a non-contact profilometer. Results: stainless steel wires had a higher hardness and a higher elastic modulus compared to titanium wires and white gold chain. The titanium wire and the white gold chain showed much more roughness than other wires. Conclusions: stainless steel wires are the most resistant, considering both the shape retention capacity and the ability to resist abrasive wear. The titanium wire showed the lowest hardness and, thus, the highest susceptibility to deformation. Bond-a-braid, Retainium and Orthoflex white gold are more resistant to fracture than other steel wires. Titanium wire and chain retainer wires have more roughness, which is a great advantage in terms of mechanical adhesion to composite materials. Full article

Easy maintenance and high durability are expected in structures made with fiber-reinforced cementitious composite (FRCC) reinforced with fiber-reinforced polymer (FRP) bars. In this study, we focused on the bond and cracking characteristics of polyvinyl alcohol (PVA)-FRCC reinforced with braided AFRP bars (AFRP/PVA-FRCC). Pullout tests on specimens with varying bond lengths were conducted. Beam specimens were also subjected to four-point bending tests. In the pullout tests, experimental parameters included the cross-sectional dimensions and the fiber volume fractions of PVA-FRCC. A trilinear model for the bond constitutive law (bond stress–loaded-end slip relationship) was proposed. In the pullout bond test with specimens of long bond length, bond strength was found to increase with increases in both the fiber volume fraction and the cross-sectional dimension of the specimens. Bond behavior in specimens of long bond length was analyzed numerically using the proposed bond constitutive law. The calculated average bond stress–loaded-end slip relationships favorably fitted the test results. In bending tests with AFRP/PVA-FRCC beam specimens, high ductility was indicated by the bridging effect of fibers. The number of cracks increased with increases in the fiber volume fraction of PVA-FRCC. In specimens with a fiber volume fraction of 2%, the load reached its maximum value due to compression fracture of the FRCC. The crack width in PVA-FRCC calculated by the predicted formula, considering the bond constitutive law and the fiber bridging law, showed good agreement with the reinforcement strain–crack width relationship obtained from the tests. Full article

Fiber materials have advantages such as light weight and high strength, corrosion resistance, fatigue resistance, and easy processing and production, and they are widely applied in the repair and renovation of concrete structures. To promote the construction convenience of fiber materials, fiber raw yarn is continuously braided to form fiber-belt-bars. Based on the existing research, the performance of bonding between fiber-belt-bars and a concrete interface was investigated, and pull-out tests were performed to systematically investigate the effects of the fiber-belt-bar cross-sectional size, anchorage length, concrete strength, and fiber type on the bonding performance. The experimental results show that the bond strength reduces with an increase in the anchorage length, increase in cross-sectional size, and decrease in concrete strength, and the effect of fiber type on the bond strength is not obvious. On this basis, a formula for calculating the average bond strength of fiber-belt-bars is proposed. Experiments and calculations determined that the average bond strength between fiber-belt-bar and concrete with a cross-sectional size of 12 mm × 3 mm is 10–30% higher than that with a cross-sectional size of 20 mm × 3 mm for the same anchorage length. Finally, the minimum anchorage length of the fiber-belt-bar is proposed to provide a valuable reference for the use of fiber-belt-bar in concrete projects. Full article

Textile reinforcements have established themselves as a convincing alternative to conventional steel reinforcements in the building industry. In contrast to ribbed steel bars that ensure a stable mechanical interlock with concrete (form fit), the bonding force of smooth carbon rovings has so far been transmitted primarily by an adhesive bonding with the concrete matrix (material fit). However, this material fit does not enable the efficient use of the mechanical load capacity of the textile reinforcement. Solutions involving surface-profiled rods promise significant improvements in the bonding behavior by creating an additional mechanical interlock with the concrete matrix. An initial analysis was carried out to determine the effect of a braided rod geometry on the bonding behavior. For this purpose, novel braided rods with defined surface profiling consisting of several carbon filament yarns were developed and characterized in their tensile and bond properties. Further fundamental examinations to determine the influence of the impregnation as well as the application of a pre-tension during its consolidation in order to minimize the rod elongation under load were carried out. The investigations showed a high potential of the impregnated surface-profiled braided rods for a highly efficient application in concrete reinforcements. Hereby, a complete impregnation of the rod with a stiff polymer improved the tensile and bonding properties significantly. Compared to unprofiled reinforcement structures, the specific bonding stress could be increased up to 500% due to the strong form-fit effect of the braided rods while maintaining the high tensile properties. Full article

This case report presents a study of unwanted tooth movements during the retention phase after orthodontic treatment. The early recognition of these unwanted tooth movements is paramount for patients and clinicians to prevent the associated negative consequences. A 21-year-old male presented with aesthetic complaints regarding his upper front teeth. He underwent orthodontic treatment at the age of 9 years and 11 months and finished his treatment 2 years and 11 months later. Flexible spiral wires (FSW) were bonded to the anterior segment of the upper and lower jaws to stabilize the end result. The failure of the fixed retainers had never occurred previously. The diagnostic assessment demonstrated a previously orthodontically treated class I malocclusion with excessive angulation and torque differences in the maxillary anterior segment. To correct the position of the maxillary anterior segment and prevent further misalignment, the patient received orthodontic re-treatment. Thereafter, the result was retained with fixed braided-rectangular-wire (BRW) retainers located at 12–22 and 33–43 and a vacuum-formed retainer (VFR) in the maxilla. The end result appeared to be stable after 28 months of retention. Unwanted tooth movements can occur during the orthodontic retention phase and might result from the use of fixed flexible spiral wire retainers. Follow-up appointments are recommended to monitor the stability and recognize these movements. Full article

Background: During the last decade, there has been an increased demand for non-metallic materials in orthodontics due to allergies, compatibility with medical imaging devices such as MRI, and aesthetic reasons. Monolithic poly-ether-ether-ketone material could address medical issues such as allergies and MRI compatibility. Moreover, nickel–titanium (NiTi) archwires covered in PEEK, either by a tube or electrophoretic deposition, could address esthetic concerns. This scoping review aims to summarize the available evidence in the literature to provide an overview of the applications and material properties of PEEK in orthodontics. Methods: This scoping review was conducted according to the Joanna Briggs Institute Manual for Evidence Synthesis for scoping reviews and the Preferred Reporting Items for Systematic Review and Meta-Analyses Protocols extension for Scoping Reviews (PRISMA-ScR). We searched for relevant publications in MEDLINE (via PubMed), Embase, Web of Science, Cochrane Library, CENTRAL, ProQuest, and SCOPUS. A gray literature search was conducted on Google Scholar. Results: Six studies were included. In three studies, the authors investigated the feasibility of developing a composite PEEK-NiTi wire, while in two other studies, the authors investigated the feasibility of monolithic PEEK wires. In the final study, the authors investigated the feasibility of PEEK as a bonded retainer. Conclusions: The included studies show promising results in developing monolithic and composite (PEEK-NiTi) materials. Further research on the robustness of PEEK composites in the oral cavity, the status of cytotoxicity and roughness values, and the (bio)-mechanical behavior of the composites is needed. A homogenously set up comparative study of clinically relevant, evenly sized, monolithic PEEK wires versus conventional orthodontic wires for their biomechanical, mechanical, and material properties would clarify the possibilities of developing monolithic PEEK wires. Missing data in the retainer study suggest more research on the mechanical properties and points of failure of PEEK-bonded retainers, and a comparative study comparing the failure and mechanical properties of PEEK-bonded retainers to flat braided metallic bonded retainers is needed. Full article

The lightweight property of helical composite spring (HCS) applied in the transportation field has attracted more and more attention recently. However, it is difficult to maintain stiffness and fatigue resistance at the same time. Herein, inspired by collagen fibers in bone, a bionic basalt fiber/epoxy resin helical composite spring is manufactured. The collagen fibers consist of nanoscale hydroxyapatite (increases stiffness) and collagen molecules composed of helical amino acid chains (can increase fatigue resistance). Such a helical structure of intercalated crystals ensures that bone has good resistance to fracture. Specifically, we first investigated the effect of adding different contents of NS to basalt fibers on the stiffness and fatigue properties of an HCS. The results show that the optimal NS content of 0.4 wt% resulted in 52.1% and 43.5% higher stiffness and fatigue properties of an HCS than those without NS, respectively. Then, two braided fiber bundles (TS-BFB) and four braided fiber bundles (FS-BFB) were designed based on the helical structure of amino acid chains, and the compression tests revealed that the maximum load resistance of TS-BFB and FS-BFB was increased by 29.2% and 44%, respectively, compared with the conventional single fiber bundle (U-BFB). The superior mechanical performance of TS-BFB and FS-BFB is attributed to the more adequate bonding of 0.4 wt% NS to the epoxy resin and the multi-fiber bundles that increase the transverse fiber content of the spring. The findings in this work introduce the bionic collagen fiber structure into the design for an HCS and provide a new idea to improve the spring performance. Full article

Background: Fixed retainers assist in maintaining the outcomes of orthodontic treatment. Fixed retention may be affected by bruxism. Objective: Evaluate two adhesives (an ormocer and a flowable composite) used for fixed orthodontic retention in simulated bruxism settings, compared to regular mastication, using a dual axis chewing simulator. Methods: Eighty human teeth were used. Periodontal tissues were simulated and exposed to 120,000 mechanical cycles, corresponding to 6 months of clinical service. Each set of two teeth was supplied with a pre-shaped, fixed, multi-braided, stainless steel wire retainer, in 1.5 cm portions, to establish passive contact with the lingual surface of the teeth. The Adhesive Remnant Index (ARI) was used to evaluate the shear bond strength. A stereomicroscope was used to assess the micro-infiltration. Results: There was no significant difference in the mean value of micro-infiltration between adhesives in the mastication group but in the bruxism group. During testing, one composite sample (ARI score 1) was broken in the mastication group, while three ormocer samples (ARI score 2) and one composite sample (ARI score 1) were broken in the bruxism group. Conclusions: The mean value for micro-infiltration in composite (0.31) was more than double that in ormocer (0.13). Full article

Anterior Cruciate Ligament (ACL) injuries are becoming more prevalent in athletes. Anterior Cruciatum Ligament Reconstruction (ACLR) surgery was used to treat ACL injuries and resulted in a recurrence rate of 94% due to the biomechanically repaired tissue being weaker than the original tissue. As a result, biodegradable artificial ligaments must be developed that can withstand mechanical stress during neoligament formation and stabilize the ACL. The purpose of this study is to determine the effect of composition variations in polylactic acid (PLA) and polycaprolactone (PCL) used as ACL nanofiber scaffolds on ultimate tensile strength (UTS) and modulus of elasticity, fiber diameter, cytotoxicity level, and degradation level, as well as the PLA-PCL concentration that provides the best value as an ACL scaffold. Electrospinning was used to fabricate the nanofiber scaffold with the following PLA-PCL compositions: A (100:0), B (85:15), C (80:20), D (70:30), and E (0:100) (wt%). The functional group test revealed no new peaks in any of the samples, and the ester group could be identified in the C-O bond at wave numbers 1300–1100 cm⁻¹ and in the C=O bond at wave numbers 1750–1730 cm⁻¹. The average fiber diameter, as determined by SEM morphology, is between 1000 and 2000 nm. The unbraided sample had a UTS range of 1.578–4.387 MPa and an elastic modulus range of 8.351–141.901 MPa, respectively, whereas the braided sample had a range of 0.879–1.863 MPa and 2.739–4.746 MPa. The higher the PCL composition, the lower the percentage of viable cells and the faster the sample degrades. All samples had a cell viability percentage greater than 60%, and samples C, D, and E had a complete degradation period greater than six months. The ideal scaffold, Sample C, was composed of PLA-PCL 80:20 (wt%), had an average fiber diameter of 827 ± 271 nm, a living cell percentage of 97.416 ± 5.079, and a degradation time of approximately 219 days. Full article

Natural gas is an important and fast-growing energy resource in the world and its purification is important in order to reduce environmental hazards and to meet the required quality standards set down by notable pipeline transmission, as well as distribution companies. Therefore, membrane technology has received great attention as it is considered an attractive option for the purification of natural gas in order to remove impurities such as carbon dioxide (CO₂) and hydrogen sulphide (H₂S) to meet the usage and transportation requirements. It is also recognized as an appealing alternative to other natural gas purification technologies such as adsorption and cryogenic processes due to its low cost, low energy requirement, easy membrane fabrication process and less requirement for supervision. During the past few decades, membrane-based gas separation technology employing hollow fibers (HF) has emerged as a leading technology and underwent rapid growth. Moreover, hollow fiber (HF) membranes have many advantages including high specific surface area, fewer requirements for maintenance and pre-treatment. However, applications of hollow fiber membranes are sometimes restricted by problems related to their low tensile strength as they are likely to get damaged in high-pressure applications. In this context, braid reinforced hollow fiber membranes offer a solution to this problem and can enhance the mechanical strength and lifespan of hollow fiber membranes. The present review includes a discussion about different materials used to fabricate gas separation membranes such as inorganic, organic and mixed matrix membranes (MMM). This review also includes a discussion about braid reinforced hollow fiber (BRHF) membranes and their ability to be used in natural gas purification as they can tackle high feed pressure and aggressive feeds without getting damaged or broken. A BRHF membrane possesses high tensile strength as compared to a self-supported membrane and if there is good interfacial bonding between the braid and the separation layer, high tensile strength, i.e., upto 170Mpa can be achieved, and due to these factors, it is expected that BRHF membranes could give promising results when used for the purification of natural gas. Full article

The aim of the study was to analyze retention protocols and materials for fixed retainers used by clinicians providing orthodontic treatment in Poland. The survey was carried out from February to April 2021. The questionnaire was designed using the Google Forms tool. After validation, the questionnaire was delivered to verified active orthodontists gathered in a closed social media group of 615 members. Finally, 104 answers were received. Answers to individual questions were provided in percentages and tabularized. A chi-squared test of proportion was used to compare: the proportion of clinicians using retainers of different characteristics and the proportions of clinicians indicating the superiority of a given clinical solution. Rectangular steel braided wire was rated as most reliable. However, doctors who declared to use gold chain were mostly solely using this type of wire. Multistranded round wire was rated the worst. Fiber-reinforced composite was mainly used in periodontal patients. The protocols used by Polish orthodontic practitioners relied on double long-term retention with regular follow-up. The most popular material was stainless steel braided rectangular wire bonded with a flowable composite. Most clinicians believed they could maintain the treatment results, but they declared that patients’ cooperation was a challenge. Full article

Poor interfacial bonding between stainless steel wire and the inner and outer layer resin matrix significantly affects the mechanical performance of braid-reinforced composite hollow fiber tube, especially torsion control. In this work, a coating of thermoplastic polyurethane (TPU) deposited on the surface of stainless steel wire greatly enhanced the mechanical performance of braid-reinforced composite hollow fiber tube. This method takes advantage of the hydrogen bonding between polyether block amide (PEBA) and thermoplastic polyurethane (TPU) for surface modification of stainless steel wire, as well as the good compatibility between PEBA and TPU. The mechanical properties of composited tubes demonstrate that the interlaminar shear strength, modulus of elasticity, and torque transmission properties were enhanced by 27.8%, 42.1%, and 41.4%, respectively. The results indicating that the interfacial adhesion between the coated stainless steel wire and the inner and outer matrix was improved. In addition, the interfacial properties of composite hollow fiber tube before and after coating was characterized by the optical microscope, and results show that the interfacial adhesion properties of the modified stainless steel wire reinforced resin matrix composites were greatly improved. Full article

Hydroxyapatite (HA) coating is successfully prepared by electrodeposition on the surface of polyvinyl alcohol (PVA)/polylactic acid (PLA) braid which serves as a potential biodegradable bone scaffold. The surface morphology, element composition, crystallinity and chemical bonds of HA coatings at various deposition times (60, 75, 90, 105 and 120 min) are characterized by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR), respectively. Average Surface roughness (Ra) of HA coating is observed by confocal microscopy. The results reveal that the typical characteristic peaks of the FTIR spectrum confirm that HA coating is successfully prepared on the rugged surface of the PVA/PLA braid. The XRD results indicate that the crystallinity of HA can be improved by increasing deposition time. In the 90 min-deposition, hydroxyapatite has a dense and uniform coating morphology, Ca/P ratio of 1.7, roughness of 0.725 μm, which shows the best electrodeposition performance. The formation mechanism of granular and plate-like hydroxyapatite crystals is explained by the structural characteristics of a hydroxyapatite unit cell. This study provides a foundation for a bone scaffold braided by biodegradable fibers. Full article

A kind of composite was designed and additive manufacturing (AM) technology was utilized in the braiding structure fabrication. The printed polylactic acid (PLA) braiding structures were integrated with two types of resins (Epon 828 resin and urethane dimethacrylate/triethylene glycol dimethacrylate (UDMA/TEDGMA) resin) used as the matrix to make composite specimens. The compression test of the composite specimens showed that the printed PLA braiding structures had the effect of varying the compression properties of pure resins: it decreased the compression properties of Epon 828 resin, but increased those of UDMA/TEGDMA resin. Observing scanning electron microscope (SEM) images, it was noted that the decreasing and increasing in the compression properties of the specimens were related to the bonding compactness between the printed braiding structure and resins. Our results may suggest a new methods for the fast manufacturing of AM-based composites, further research directions, and potential applications of this kind of composites. Full article