Search Results (30)

This study explored the enzymatic formation of gel-like polymeric matrices through carbonate precipitation for dust suppression in Yellow River silt. The hydrogel-modified EICP method effectively enhanced the compressive strength and resistance to wind–rain erosion by forming a reinforced bio-cemented crust. The optimal cementation solution, consisting of urea and CaCl₂ at equimolar concentrations of 1.25 mol/L, was applied to improve CaCO₃ precipitation uniformity. A spraying volume of 4 L/m² (first urea-CaCl₂ solution, followed by urease solution) yielded a 14.9 mm thick hybrid gel-CaCO₃ crust with compressive strength exceeding 752 kPa. SEM analysis confirmed the synergistic interaction between CaCO₃ crystals and the gel matrix, where the hydrogel network acted as a nucleation template, enhancing crystal bridging and pore-filling efficiency. XRD analysis further supported the formation of a stable gel-CaCO₃ composite structure, which exhibited superior resistance to wind–rain erosion and mechanical wear. These findings suggest that gel-enhanced EICP represents a novel bio-gel composite technology for sustainable dust mitigation in silt soils. Full article

Waste nanomaterials pose environmental and human health concerns and they need to be urgently and efficiently managed. In this study, a fungal biotemplate was used to accumulate and recover nano-Fe₂O₃ materials from an aqueous solution. Then, recovered nano-Fe₂O₃ materials were activated to form a high-performance magnetic porous carbon composite (FePC) for energy storage and organic pollutant removal. The results indicate that high concentrations (500 mg/L) of 50 nm Fe₂O₃ particles can be completely recovered using a cross-linked Neurospora crassa fungus (NC), primarily because of its encapsulation function. In addition, the surface area, degree of graphitization, and heteroatom content of the FePC materials can be boosted by the catalytic effects of the incorporated Fe atoms. The developed FePC materials exhibit potential as high electrical double-layer capacitors as well as strong retention capabilities, excellent stability, and efficient adsorption of triclosan (TCS, ~526 mg/g). Additionally, these FePC materials exhibit superior capacities for energy storage and pollutant reduction compared to commercial and reported carbon materials. These results reveal a sustainable route for the recovery and reutilization of nanomaterials. Full article

Biotemplating technique allows the synthesis of catalysts, recreating the sophisticated structure of nature templates. In this work, some biotemplated TiO₂ semiconductors were synthesized using Olea europaea leaves as templates. Then, g-C₃N₄ was coupled to materials to later incorporate Pt on the surface or as dopant in the structure to evaluate the efficiency of the solids in two photocatalytic applications to valorize biomass: hydrogen production through glycerol photoreforming, and photoacetalization of cinnamaldehyde with 1,2-propanediol. In glycerol photoreforming, the presence of Pt (superficial or dopant) enhanced hydrogen production, being Pt@AOLCN (a heterojunction containing biotemplated TiO₂, g-C₃N₄, and Pt) the system that exhibited the highest efficiency (3053.4 µmol·g_cat⁻¹·h⁻¹). For photoacetalization, while Pt reduced cinnamaldehyde conversion, it improved selectivity when incorporated on TiO₂. Notably, carbon nitride (CN) exhibited the highest yield after 16 h of testing. The study emphasizes the importance of tailoring catalyst selection to specific reactions, as efficiency is closely tied to the structural and chemical properties of the materials. These findings contribute to the development of efficient photocatalysts for sustainable biomass valorization processes. Full article

In this study, TiO₂/P, K-containing grapefruit peel biochar (TiO₂/P, K-PC) composites were synthesized in situ biomimetically using grapefruit peel as the bio-template and carbon source and tetrabutyl titanate as the titanium source. This was achieved using the two-step rotary impregnation–calcination method. Adjusting the calcination temperature of the sample in an air atmosphere could regulate the mass ratio of TiO₂ to carbon. The prepared samples were subjected to an analysis of their compositions, structures, morphologies, and properties. It demonstrated that the prepared samples were complexes of anatase TiO₂ and P, K-containing carbon, with the presence of graphitic carbon. They possessed a unique morphological structure with abundant pores and a large surface area. The grapefruit peel powder played a crucial role in the induction and assembly of TiO₂/P, K-PC composites. The sample PCT-400-550 had the best photocatalytic activity, with the degradation rate of RhB, MO, and MB dye solutions reaching more than 99% within 30 min, with satisfactory cyclic stability. The outstanding photocatalytic activity can be credited to its unique morphology and the efficient collaboration between TiO₂ and P, K-containing biochar. Full article

The advancement of both porous materials and nanomaterials has brought about porous nanomaterials. These new materials present advantages both due to their porosity and nano-size: small size apt for micro/nano device integration or in vivo transport, large surface area for guest/target molecule adsorption and interaction, porous channels providing accessibility to active/surface sites, and exposed reactive surface/active sites induced by uncoordinated bonds. These properties prove useful for the development of different porous composition types (metal oxides, silica, zeolites, amorphous oxides, nanoarrays, precious metals, non-precious metals, MOFs, carbon nanostructures, MXenes, and others) through different synthetic procedures—templating, colloidal synthesis, hydrothermal approach, sol-gel route, self-assembly, dealloying, galvanostatic replacement, and so—for different applications, such as catalysis (water-splitting, etc.), biosensing, energy storage (batteries, supercapacitors), actuators, SERS, and bio applications. Here, these are presented according to different material types showing the evolution of the structure design and development towards the formation of hierarchical porous structures, emphasizing that the formation of porous nanostructures came about out of the desire and need to form hierarchical porous nanostructures. Common trends observed across these different composition types include similar (aforementioned) applications and the use of porous nanomaterials as templates/precursors to create novel ones. Towards the end, a discussion on the link between technological advancements and the development of porous nanomaterials paves the way to present future perspectives on these nanomaterials and their hierarchical porous architectures. Together with a summary, these are given in the conclusion. Full article

The presented study demonstrates the capability of the template-based electrokinetic assembly (TEA) and guidance to manipulate and capture individual biological cells within a microfluidic platform. Specifically, dielectrophoretic (DEP) focusing of K-562 cells towards lithographically-defined “wells” on the microelectrodes and positioning singles cells withing these “wells” was demonstrated. K-562 lymphoblast cells, are widely used in immunology research. The DEP guidance, particularly involving positive DEP (pDEP), enables the controlled guidance and positioning of conductive and dielectric particles, including biological cells, opening new directions for the accurate and efficient microassembly of biological entities, which is crucial for single cell analysis and other applications in biotechnology. The investigation explores the use of glassy carbon and gold as electrode materials. It was established previously that undiluted physiological buffer is unsuitable for inducing positive DEP (pDEP); therefore, the change of media into a lower ionic concentration is necessary. After pDEP was observed, the cells are resubmerged in the Iscove’s modified Dulbecco’s medium (IMEM), a cell culturing media, and incubated. A dead/alive staining assay was performed on the cells to determine their survival in the diluted buffer for the period required to capture them. The staining assay confirmed the cells’ survival after being immersed in the diluted biological buffer necessary for electrokinetic handling. The results indicate the promise of the proposed electrokinetic bio-sorting technology for applications in tissue engineering, lab-on-a-chip devices, and organ-on-a-chip models, as well as contributing to the advancement of single cell analysis. Full article

Nature provides various templates for integrating organic and inorganic materials to create high-performance composites. Biological structures such as nacre and the structural elements of the glass sponge are built up in layers, leading to remarkable fracture toughness. In this work, the brick-and-mortar and layer-by-layer structures found in these biological examples have been abstracted and implemented by using an aqueous polymer dispersion in combination with nanoclay particles and sodium water glass. These dispersions were used as impregnation of carbon rovings in order to form bio-inspired contact zones towards the concrete matrix. The bonding behavior was investigated using the Yarn Pull-Out (YPO) test, and a beneficial behavior of the layered polymer–nanoclay dispersions was observed. Thermogravimetric analysis (TGA) was used to determine the organic impregnation content of the roving. Further, light microscopy of the roving cross-sections prior to YPO and visual analyses of the fractured contact zone of split concrete specimens provided information on the quality of the impregnation and the interaction with the concrete matrix. Full article

Nowadays, commercial electric double-layer supercapacitors mainly use porous activated carbons due to their high specific surface area, electrical conductivity, and chemical stability. A feature of carbon materials is the possibility of obtaining them from renewable plant biomass. In this study, fungi (Fomes fomentarius) were used as a bio-template for the preparation of carbon fibers via a combination of thermochemical conversion approaches, including a general hydrothermal pre-carbonization step, as well as subsequent carbonization, physical, or chemical activation. The relationships between the preparation conditions and the structural and electrochemical properties of the obtained carbon materials were determined using SEM, TEM, EDAX, XPS, cyclic voltammetry, galvanostatic measurements, and EIS. It was shown that hydrothermal pretreatment in the presence of phosphoric acid ensured the complete removal of inorganic impurities of raw fungus hyphae, but at the same time, saved some heteroatoms, such as O, N, and P. Chemical activation using H₃PO₄ increased the amount of phosphorus in the carbon material and saved the natural fungus’s structure. The combination of a hierarchical pore structure with O, N, and P heteroatom doping made it possible to achieve good electrochemical properties (specific capacitance values of 220 F/g) and excellent stability after 25,000 charge/discharge cycles in a three-electrode cell. The electrochemical performance in both three- and two-electrode cells exceeded or was comparable to other biomass-derived porous carbons, making it a prospective candidate as an electrode material in symmetrical supercapacitors. Full article

Hexagonal SBA-15 mesoporous material was used as a catalytic template for impregnation, with the transition metals Fe, Co, and Ni as catalysts for chemical transformation. Nitrogen adsorption/desorption isotherms, scanning electron microscopy, and transmission electron microscopy were conducted to better understand the physicochemical properties of the metal oxide-impregnated SBA-15. The specific surface area of the original SBA-15 was approximately 680 m²/g, and the abundances of the catalysts impregnated ranged from 2 to 8%, corresponding to specific surface areas of 560–470 m²/g for Fe-SBA-15, 440–340 m²/g for Ni-SBA-15, and 410–340 m²/g for Co-SBA-15. The increase in impregnated metal loadings filled the pores and collapsed the silica walls during the metal oxides impregnation on SBA-15 and calcination procedures, resulting in a decrease in the specific surface area and pore volume of the templates. The results showed that the order of nitrogen adsorbed was SBA-15 > Fe-SBA-15 > Ni-SBA-15 > Co-SBA-15 when the metal loading was 5%. In addition, the metal oxides on SBA-15 increased the wall thickness compared with raw SBA-15. Based on the XRD spectrum analysis, Fe₂O₃, Co₃O₄, and NiO were the stable crystals on the Fe-SBA-15, Co-SBA-15, and Ni-SBA-15, respectively. The sequence of the average grain size of metal oxides on SBA-15 was Co-SBA-15 > Fe-SBA-15 > Ni-SBA-15, according to XRD spectra and Scherrer’s equation. Isopropanol could be decomposed by metal oxide-impregnated SBA-15 to form carbon filament materials. Therefore, these materials have the potential to be employed for pollutant removal, catalytic reactions for organic solvent and bio-oil/biomass reforming, and recycling waste into high-value materials. Full article

In terms of new-generation energy-storing devices, aqueous zinc-ion batteries (AZIBs) are becoming the prime candidates because of their inexpensive nature, inherent safety, environmental benignity and abundant resources. Nevertheless, due to a restrained selection of cathodes, AZIBs often perform unsatisfactorily under long-life cycling and high-rate conditions. Consequently, we propose a facile evaporation-induced self-assembly technique for preparing V₂O₃@carbonized dictyophora (V₂O₃@CD) composites, utilizing economical and easily available biomass dictyophora as carbon sources and NH₄VO₃ as metal sources. When assembled in AZIBs, the V₂O₃@CD exhibits a high initial discharge capacity of 281.9 mAh g⁻¹ at 50 mA g⁻¹. The discharge capacity is still up to 151.9 mAh g⁻¹ after 1000 cycles at 1 A g⁻¹, showing excellent long-cycle durability. The extraordinary high electrochemical effectiveness of V₂O₃@CD could be mainly attributed to the formation of porous carbonized dictyophora frame. The formed porous carbon skeleton can ensure efficient electron transport and prevent V₂O₃ from losing electrical contact due to volume changes caused by Zn²⁺ intercalation/deintercalation. The strategy of metal-oxide-filled carbonized biomass material may provide insights into developing high-performance AZIBs and other potential energy storage devices, with a wide application range. Full article

The high-temperature sintering of CaO-based materials leads to the serious decay of energy storage performance during the calcination/carbonation cycle. To overcome the loss in porosity problem, an efficient CaO-based material for thermal energy storage was synthesized using bamboo fiber as the biotemplate. The synthesis parameters (bamboo fiber addition, pyrolysis, Al₂O₃ loading) and the energy storage reaction characteristics of CaO-based energy storage material were optimized on the basis of cyclic calcination/carbonation experiments. The results show that the sacrificed biotemplate enhances the porosity of the synthetic material, denoting improved energy storage density. The cumulative energy storage density of the templated material over 50 cycles is 24,131.44 kJ/kg higher than that of limestone. The carbonation conversion and energy storage density of the templated CaO-based material doped with 5 wt.% Al₂O₃ and 0.5 g bamboo fiber reach 0.75 mol/mol and 2368.82 kJ/kg after 10 cycles, respectively, which is 2.7 times as high as that of original limestone. The maximum apparent carbonation rate of the templated CaO-based materials in the 1st cycle corresponds to a 240% increment compared to limestone. The maximum calcination rate of the synthetic CaO-based material in the 12th cycle remains 93%, as compared with the initial cycle. The microstructure analysis reveals that the hierarchically-stable structure during the cycle is beneficial for a more effective exposure of surface reactive sites for CaO and inward/outward diffusion for CO₂ molecules through CaO. The method using the sacrificed biological template provides an advanced approach to fabricate porous materials, and the composite CaO-based material provides high-return solar energy storage for a potential application in industrial scale. Full article

MoS₂/bio-template carbon composite materials with outstanding photocatalytic degradation performance were constructed and synthesized by an impregnation–hydrothermal–calcination (IHC) method. Composites of the same type were synthesized by a direct-impregnation–calcination (DIC) method for comparison. The results showed that calcination process was obtained from biotemplate carbon with preserved structure. IHC method obtained petal-like MoS₂, while DIC method obtained needle-like MoS₂. The composite material exhibits adsorption–catalytic degradation performance. Driven by visible light, the photocatalytic degradation efficiency of the composites synthesized by IHC method for humic acid reached 98.73% after 150 min of illumination. Full article

In this report, we demonstrated the formation of a biomimetic mineralizing layer obtained on the surface of dental enamel (biotemplate) using bioinspired nanocrystalline carbonate-substituted calcium hydroxyapatite (ncHAp), whose physical and chemical properties are closest to the natural apatite dental matrix, together with a complex of polyfunctional organic and polar amino acids. Using a set of structural, spectroscopy, and advanced microscopy techniques, we confirmed the formation of a nanosized ncHAp-based mineralized layer, as well as studying its chemical, substructural, and morphological features by means of various methods for the pretreatment of dental enamel. The pretreatment of a biotemplate in an alkaline solution of Ca(OH)₂ and an amino acid booster, together with the executed subsequent mineralization with ncHAp, led to the formation of a mineralized layer with homogeneous micromorphology and the preferential orientation of the ncHAp nanocrystals. It was shown that the homogeneous crystallization of hydroxyapatite on the biotemplate surface and binding of individual nanocrystals and agglomerates into a single complex by an amino acid booster resulted in an increase (~15%) in the nanohardness value in the enamel rods area, compared to that of healthy natural enamel. Obtaining a similar hierarchy and cleavage characteristics as natural enamel in the mineralized layer, taking into account the micromorphological features of dental tissue, is an urgent problem for future research. Full article

Cellulose is the most abundant natural polymer and deserves the special attention of the scientific community because it represents a sustainable source of carbon and plays an important role as a sustainable energent for replacing crude oil, coal, and natural gas in the future. Intense research and studies over the past few decades on cellulose structures have mainly focused on cellulose as a biomass for exploitation as an alternative energent or as a reinforcing material in polymer matrices. However, studies on cellulose structures have revealed more diverse potential applications by exploiting the functionalities of cellulose such as biomedical materials, biomimetic optical materials, bio-inspired mechanically adaptive materials, selective nanostructured membranes, and as a growth template for inorganic nanostructures. This article comprehensively reviews the potential of cellulose structures as a support, biotemplate, and growing vector in the formation of various complex hybrid hierarchical inorganic nanostructures with a wide scope of applications. We focus on the preparation of inorganic nanostructures by exploiting the unique properties and performances of cellulose structures. The advantages, physicochemical properties, and chemical modifications of the cellulose structures are comparatively discussed from the aspect of materials development and processing. Finally, the perspective and potential applications of cellulose-based bioinspired hierarchical functional nanomaterials in the future are outlined. Full article

Hollow carbon nitride nanosphere (HCNS) was synthesized via the hard template method to improve the fluorescence characteristics, drug delivery ability, and photocatalytic activity. Blue fluorescent HCNS was utilized as a quenching agent and an internal reference to combine with Cy5-labelled aptamer (Cy5-Apt), resulting in an off-on fluorescence aptasensing method for the detection of Salmonella typhimurium (S. typhimurium). Under optimum conditions, this fluorescence assay presented a linear range from 30 to 3 × 10⁴ CFU mL⁻¹ with a detection limit of 13 CFU mL⁻¹. In addition, HCNS was also used as a drug carrier to load chloramphenicol (Cap) molecules. The Cap-loading amount of HCNS could reach 550 μg mg⁻¹ within 24 h, whereas the corresponding Cap-release amount is 302.5 μg mg⁻¹ under acidic and irradiation conditions. The integration of photocatalyst with antibiotic could endow HCNS-Cap with better disinfection performance. The bactericidal efficiency of HCNS-Cap (95.0%) against S. typhimurium within 12 h was better than those of HCNS (85.1%) and Cap (72.9%). In addition, selective disinfection of S. typhimurium was further realized by decorating aptamer. Within 4 h, almost all S. Typhimurium were inactivated by HCNS-Cap-Apt, whereas only 13.3% and 48.2% of Staphylococcus aureus and Escherichia coli cells were killed, respectively. Therefore, HCNS is a promising bio-platform for aptamer-based fluorescence detection and selective disinfection of S. typhimurium. Full article