Search Results (27)

Climate change is significantly affecting water availability, emphasising the need for sustainable strategies such as wastewater reuse. While this represents a promising alternative resource, insufficiently treated wastewater may pose health risks, particularly through aerosol formation during irrigation, which can facilitate Legionella transmission. This study aimed to evaluate the presence of Legionella across various stages in a wastewater treatment plant (WWTP) that reuses effluent for agricultural purposes. Samples from the influent, four treatment phases, and the final effluent were analysed using both culture-based methods and quantitative PCR (qPCR) for Legionella spp. and L. pneumophila. qPCR detected Legionella spp. in all samples and L. pneumophila in 66% of them. In contrast, the culture-based analysis showed much lower detection levels, with only one positive sample at the influent stage—likely due to microbial interference or growth inhibition. Although contamination decreased in the final effluent, Legionella was still detected in water designated for reuse (Legionella spp. in 100% and L. pneumophila in 17% of samples). No treatment stage appeared to promote Legionella proliferation, likely due to WWTP characteristics, in addition to wastewater temperature and COD. These findings underscore the importance of monitoring Legionella in reclaimed water and developing effective control strategies to ensure the safe reuse of treated wastewater in agriculture. Full article

The crystallization of soluble salts is one of the most significant agents of deterioration affecting porous building materials in historical architecture. This process not only compromises the physical integrity of the materials but also results in considerable aesthetic, structural, and economic consequences. Soluble salts involved in these processes may originate from geogenic sources—including soil leachate, marine aerosols, and the natural weathering of parent rocks—or from anthropogenic factors such as air pollution, wastewater infiltration, and the use of incompatible restoration materials. This study examines the role of capillary rise as a primary mechanism responsible for the vertical migration of saline solutions from the soil profile into historic masonry structures, especially those constructed with calcareous stones. It describes how water retained or sustained within the soil matrix ascends via capillarity, carrying dissolved salts that eventually crystallize within the pore network of the stone. This phenomenon leads to a variety of damage types, ranging from superficial staining and efflorescence to more severe forms such as subflorescence, microfracturing, and progressive mass loss. By adopting a multidisciplinary approach that integrates concepts and methods from soil physics, hydrology, petrophysics, and conservation science, this paper examines the mechanisms that govern saline water movement, salt precipitation patterns, and their cumulative effects on stone durability. It highlights the influence of key variables such as soil texture and structure, matric potential, hydraulic conductivity, climatic conditions, and stone porosity on the severity and progression of deterioration. This paper also addresses regional considerations by focusing on the context of Spain, which holds one of the highest concentrations of World Heritage Sites globally and where many monuments are constructed from vulnerable calcareous materials such as fossiliferous calcarenites and marly limestones. Special attention is given to the types of salts most commonly encountered in Spanish soils—particularly chlorides and sulfates—and their thermodynamic behavior under fluctuating environmental conditions. Ultimately, this study underscores the pressing need for integrated, preventive conservation strategies. These include the implementation of drainage systems, capillary barriers, and the use of compatible materials in restoration, as well as the application of non-destructive diagnostic techniques such as electrical resistivity tomography and hyperspectral imaging. Understanding the interplay between soil moisture dynamics, salt crystallization, and material degradation is essential for safeguarding the cultural and structural value of historic buildings in the face of ongoing environmental challenges and climate variability. Full article

Wastewater treatment plants (WWTPs) have been confirmed as reservoirs of antibiotic resistance genes (ARGs). This study systematically investigated the distribution patterns of ARGs across different treatment units in municipal WWTPs, along with the environmental drivers, dissemination characteristics, and exposure risks of aerosol-borne ARGs in aerated tank environments. The results revealed a high compositional similarity in aerosol-borne ARGs across the sampling sites, with multidrug ARGs predominating at an average relative abundance of 52%, followed sequentially by tetracycline (11%), MLS (10%), and glycopeptide resistance genes (7%). The diffusion of aerosol-borne ARGs is significantly influenced by environmental factors including temperature, relative humidity, wind speed, and total suspended particulate (TSP) concentration, with temperature being the most dominant factor affecting the dispersion of ARGs. The atmospheric dispersion model demonstrates that aerosol-borne ARGs decay with increasing downwind distance, showing potential for transport from aeration tanks to locations exceeding 1500 m along the prevailing wind direction. Both within wastewater treatment units and downwind areas, adult males had higher respiratory exposure doses but lower skin contact doses compared to females, with respiratory doses exceeding skin contact by 3–4 orders of magnitude. This study highlights the potential health risks posed by aerosol-borne ARG transmission from WWTP operations. Full article

In contemporary times, wastewater treatment plants (WWTPs) were recognized as substantial sources of odorous emissions, potentially impacting nearby communities’ sensory experience. This study investigates the half-lives (T½) of odorous compounds emitted from WWTPs and their degradation due to atmospheric hydroxyl radicals (•OH) in different environmental settings. The calculated half-lives of specific odorants in rural areas ranged from 31.36 min to 517.33 days, in urban areas from 42.50 min to 1550 days, and in the marine boundary layer from 42.50 min to 129,861 days. These results show that compounds with high reactivity and short T½, such as methanethiol and ethanethiol, degrade rapidly and are less likely to contribute to long-term odor nuisances. In contrast, compounds with longer half-lives, such as carbonyl sulfide and ammonia, persist longer in the atmosphere, with higher potential for sustained odor issues. The findings suggest that •OH plays a significant role in degrading odorous compounds. These insights into odorant–oxidant kinetics may aid in predicting atmospheric half-lives and their contribution to secondary aerosol formation, thus informing regulatory and mitigation strategies to improve air quality. Full article

Laser-induced breakdown spectroscopy (LIBS) was applied to the analysis of aerosolized Cu- and Pb-bearing particles generated from aqueous solutions. A nitrogen-driven nebulizer was utilized to aerosolize Cu- and Pb-spiked solutions. The liquid matrix of the aqueous droplets was evaporated before the LIBS analysis, and the remaining gas-phase analyte-rich aerosols were analyzed in a LIBS system that featured a 1064 nm Nd:YAG laser, a Czerny–Turner spectrometer, and an ICCD camera. The Cu and Pb concentrations in the aerosol streams were 0.26–1.29 ppm and 0.40–1.19 ppm, respectively. Laser diffraction and the particle size distributions of the aqueous aerosols were obtained to indirectly demonstrate the evaporation of the liquid matrix. Highly linear calibration curves (R² = 0.995 for Cu and R² = 0.987 for Pb) and acceptable limits of detection (2 ppb for Cu and 9 ppb for Pb) and quantification (5 ppb and 28 ppb) were obtained. The applications of the presented methodology include the near-real-time and in situ analysis of wastewater and gas-phase aerosols contaminated with heavy metals. Full article

Waterborne illnesses lead to millions of fatalities worldwide each year, particularly in developing nations. In this paper, we introduce a comprehensive system designed for the autonomous early detection of viral outbreaks transmitted through water to ensure sustainable access to healthy water resources, especially in remote areas. The system utilizes an autonomous water quality monitoring setup consisting of an airborne water sample collector, an autonomous sample processor, and an artificial intelligence-aided microscopic detector for risk assessment. The proposed system replaces the time-consuming conventional monitoring protocol by automating sample collection, sample processing, and pathogen detection. Furthermore, it provides a safer processing method against the spillage of contaminated liquids and potential resultant aerosols during the heat fixation of specimens. A morphological image processing technique of light microscopic images is used to segment images, assisting in selecting a unified appropriate input segment size based on individual blob areas of different bacterial cultures. The dataset included harmful pathogenic bacteria (A. baumanii, E. coli, and P. aeruginosa) and harmless ones found in drinking water and wastewater (E. faecium, L. paracasei, and Micrococcus spp.). The segmented labeled dataset was used to train deep convolutional neural networks to automatically detect pathogens in microscopic images. To minimize prediction error, Bayesian optimization was applied to tune the hyperparameters of the networks’ architecture and training settings. Different convolutional networks were tested in accordance with different required output labels. The neural network used to classify bacterial cultures as harmful or harmless achieved an accuracy of 99.7%. The neural network used to identify the specific types of bacteria achieved a cumulative accuracy of 93.65%. Full article

Antimicrobial resistance (AMR) has emerged as a conspicuous global public health threat. The World Health Organization (WHO) has launched the “One-Health” approach, which encourages the assessment of antibiotic resistance genes (ARGs) within an environment to constrain and alleviate the development of AMR. The prolonged use and overuse of antibiotics in treating human and veterinary illnesses, and the inability of wastewater treatment plants to remove them have resulted in elevated concentrations of these metabolites in the surroundings. Microbes residing within these settings acquire resistance under selective pressure and circulate between the air–land interface. Initial evidence on the indoor environments of wastewater treatment plants, hospitals, and livestock-rearing facilities as channels of AMR has been documented. Long- and short-range transport in a downwind direction disseminate aerosols within urban communities. Inhalation of such aerosols poses a considerable occupational and public health risk. The horizontal gene transfer (HGT) is another plausible route of AMR spread. The characterization of ARGs in the atmosphere therefore calls for cutting-edge research. In the present review, we provide a succinct summary of the studies that demonstrated aerosols as a media of AMR transport in the atmosphere, strengthening the need to biomonitor these pernicious pollutants. This review will be a useful resource for environmental researchers, healthcare practitioners, and policymakers to issue related health advisories. Full article

Studies on bioaerosol bacterial biodiversity have relevance in both ecological and health contexts, and molecular methods, such as 16S rRNA gene-based barcoded sequencing, provide efficient tools for the analysis of airborne bacterial communities. Standardized methods for sampling and analysis of bioaerosol DNA are lacking, thus hampering the comparison of results from studies implementing different devices and procedures. Three samplers that use gelatin filtration, swirling aerosol collection, and condensation growth tubes for collecting bioaerosol at an aeration tank of a wastewater treatment plant in Trieste (Italy) were used to determine the bacterial biodiversity. Wastewater samples were collected directly from the untreated sewage to obtain a true representation of the microbiological community present in the plant. Different samplers and collection media provide an indication of the different grades of biodiversity, with condensation growth tubes and DNA/RNA shield^TM capturing the richer bacterial genera. Overall, in terms of relative abundance, the air samples have a lower number of bacterial genera (64 OTUs) than the wastewater ones (75 OTUs). Using the metabarcoding approach to aerosol samples, we provide the first preliminary step toward the understanding of a significant diversity between different air sampling systems, enabling the scientific community to orient research towards the most informative sampling strategy. Full article

Pollution by plastic microparticles is rising rapidly. One avenue of human exposure to nanoparticles is through inhalation. The main source of microplastics in indoor environments, leading to unintended inhalation, is synthetic fabric used in clothing. Other sources include curtains, carpets, furniture, wall paints, and floor finishes. Occupational exposure is particularly significant in waste management and recycling operations, during exposure to high heat, during high-energy treatment of polymer composites, and during 3D printing. In outdoor environments, exposure can happen through breathing in contaminated aerosols from ocean waves or airborne particles from dried wastewater treatments. Airborne particles affect human health in various ways, including via direct interactions with the epithelium and its mucus layer after deposition in the mouth and respiratory system. Exposure due to the ingestion of microplastics present in various environmental compartments may occur either directly or indirectly via the food chain or drinking water. This study aimed to determine the effects of plastic microparticles on the rheology of mucus and saliva, and, thus, their functioning. The experiments used artificial mucus, saliva, and plastic nanoparticles (namely, PS—polystyrene and PE—polyethylene). The rheological properties of saliva and mucus were determined via the use of an oscillatory rheometer at various temperatures (namely, 36.6 °C and 40 °C, which correspond to healthy and ill humans). The results were compared with those obtained for pure saliva and mucus. An increase in apparent viscosity was observed for saliva, which is behavior typical of for solid particle suspensions in liquids. In contrast, for mucus, the effect was the opposite. The influence of the presence of the particles on the parameters of the constitutive viscosity equations was studied. Plastic micro- and nanoparticles in the saliva and mucus may interfere with their physiological functions. Full article

Due to their unique properties, iron nanoparticles find diverse applications across various fields, including catalysis, electronics, wastewater treatment, and energy storage. Nano-iron particles are mostly sub-micrometer particles that are highly reactive to both air (oxygen) and water, and in nanoparticles (size below 100 nm), it is even more rapid than the bulk material. This characteristic limits its use in inert environments. Iron nanoparticles are not toxic and are mostly used for wastewater treatment. Understanding the hydrogen reduction mechanisms and conditions that lead to the formation of metallic iron particles from iron (III)-nitrate from an aerosol is crucial for enabling their effective utilization. In this work, we studied the hydrogen reduction behavior of Fe₂O₃ in the absence and presence of additives (SiO₂ or Pt). The particles were prepared via ultrasonic spray pyrolysis and hydrogen reduction. The characterization was performed with a scanning electron microscope, energy-dispersive X-ray spectroscopy, and X-ray diffraction. In the absence of additives, the oxygen content of iron oxide particles decreased with increasing temperature from 700 to 950 °C but significantly increased with the doping of 10 mL (40 wt.%) of SiO₂. The inhibitory effect of Si on the hydrogen reduction of Fe₂O₃ formed was more pronounced at 950 °C than at 700 °C. In contrast, the doping of only 5 mL (15 wt.%) of Pt significantly decreased the oxygen concentration in the synthesized particles by catalyzing the reduction reaction of iron oxides at 700 °C. The metallic iron (Fe) product, obtained in the undoped iron oxides run at only 950 °C, was also formed at 700 °C in the Pt-doped Fe₂O₃ run. Full article

Wastewater treatment plants (WWTPs) are a crucial source of bioaerosols, which account for both environmental and health hazards. Although various culture-based studies on bioaerosols have been reported, little knowledge remains about distribution and potential risks for more omnipresent non-culturable bacterial aerosols. Here, in summer, an eight-stage Andersen air sampler was applied to capture particles of various sizes from the atmospheric environment of eight treatment units from two WWTPs in northeastern China. Particles of various sizes in aeration tank (AT) were sampled in autumn and winter. The abundance and community composition of the bacterial aerosols were investigated using 16S rRNA gene sequencing. In order to explore the importance of particle size on community composition of bacterial aerosols, this study investigated the particle size distribution of bacterial aerosols in different treatment units. The results indicated that the sludge dewatering room was the major source of bacterial aerosols in both WWTPs, with the abundance of stage VII (0.65–1.1 μm) demonstrating a 4-fold to 9-fold increase when compared to any other treatment unit. The highest relative abundance of bacterial aerosols was in autumn, while the lowest was found in winter. However, most particles detected in autumn were larger than 4.7 µm in diameter, while submicron particles (less than 1.1 µm, over 40%) were detected primarily in winter. The most 15 dominant bacterial aerosol genera in were observed at submicron level, and about half of the genera (6 and 8) were detected as human pathogens, suggesting their easier penetration to human respiratory tracts. This study demonstrates that size distribution characteristics should be crucial information for the comprehensive assessment of the potential health risks of bacterial aerosols from WWTPs. Full article

Wastewater treatment plants (WWTPs) are confirmed sources of bioaerosols and can be a hotspot for both antibiotic-resistant bacteria and antibiotic-resistant genes (ARGs). Bioaerosols can be a source of dispersion for bacteria and ARGs into the environment. Biofiltration is one of the most effective technologies to mitigate odors from WWTPs. The objective of this study was to evaluate the capacity of an odor biofiltration system designed to remove volatile compounds, to influence the airborne bacterial diversity and to reduce the aerosolized microbial and ARG concentrations. In total, 28 air samples were collected before and after treatment of an interior WWTP. Overall, air samples collected upstream had higher total bacterial concentrations, and a shift in bacterial diversity was observed. Legionella and Mycobacterium were detected in low abundance upstream and downstream, whereas Legionella pneumophila was detected but not quantifiable in two samples. Of the 31 ARGs and mobile genetic elements detected by quantitative polymerase chain reaction, 15 exhibited a significant reduction in their relative abundance after biofiltration, and none were significantly higher in the effluent. Overall, these results show the benefits of odor biofiltration systems to reduce bacterial and antimicrobial resistance in treated air, a promising application to limit environmental dispersion. Full article

The appearance of SARS-CoV-2 represented a new health threat to humanity and affected millions of people; the transmission of this virus occurs through different routes, and one of them recently under debate in the international community is its possible incorporation and spread by sewage. Therefore, the present work’s research objectives are to review the presence of SARS-CoV-2 in wastewater throughout the world and to analyze the coverage of wastewater treatment in Mexico to determine if there is a correlation between the positive cases of COVID-19 and the percentages of treated wastewater in Mexico as well as to investigate the evidence of possible transmission by aerosol sand untreated wastewater. Methodologically, a quick search of scientific literature was performed to identify evidence the presence of SARS-CoV-2 RNA (ribonucleic acid) in wastewater in four international databases. The statistical information of the positive cases of COVID-19 was obtained from data from the Health Secretary of the Mexican Government and the Johns Hopkins Coronavirus Resource Center. The information from the wastewater treatment plants in Mexico was obtained from official information of the National Water Commission of Mexico. The results showed sufficient evidence that SARS-CoV-2 remains alive in municipal wastewater in Mexico. Our analysis indicates that there is a low but significant correlation between the percentage of treated water and positive cases of coronavirus r = −0.385, with IC (95%) = (−0.647, −0.042) and p = 0.030; this result should be taken with caution because wastewater is not a transmission mechanism, but this finding is useful to highlight the need to increase the percentage of treated wastewater and to do it efficiently. In conclusions, the virus is present in untreated wastewater, and the early detection of SAR-CoV-2 could serve as a bioindicator method of the presence of the virus. This could be of great help to establish surveillance measures by zones to take preventive actions, which to date have not been considered by the Mexican health authorities. Unfortunately, wastewater treatment systems in Mexico are very fragile, and coverage is limited to urban areas and non-existent in rural areas. Furthermore, although the probability of contagion is relatively low, it can be a risk for wastewater treatment plant workers and people who are close to them. Full article

In recent years, due to the production and use of per- and poly-fluoroalkyl substances (PFASs), the research on the pollution characteristics and sources of PFASs in surface water and precipitation in China has attracted increasing attention. In this study, the related published articles with sampling years from 2010 to 2020 were reviewed, and the concentration levels, composition characteristics and possible sources of PFASs in surface water (rivers and lakes) and precipitation in China were summarized, including those in the Tibetan Plateau region. The results show that the concentrations of PFASs in surface water in different areas of China vary greatly, ranging from 0.775 to 1.06 × 10⁶ ng/L. The production processes of fluorinated manufacturing facilities (FMFs) and sewage discharge from wastewater treatment plants (WWTPS) were the main sources of PFASs in surface water in China, and the concentrations of PFASs in water flowing through cities with high urbanization increased significantly compared with those before water flowed through cities with high urbanization. The compositions of PFASs in surface water gradually changed from long-chain PFASs, such as per-fluoro-octanoic acid (PFOA) and per-fluoro-octanesulfonic acid (PFOS) to short-chain PFASs, such as per-fluorobutanoic acid (PFBA), per-fluorobutanesulfonic acid (PFBS), perfluorohexanoic acid (PFHxA) and per-fluoropentanoic acid (PFPeA). The concentrations of PFASs in precipitation in China ranged from 4.2 to 191 ng/L, which were lower than those of surface water. The precipitation concentrations were relatively high around a fluorination factory and in areas with high urbanization levels. PFASs were detected in the surface water and precipitation in the Tibetan Plateau (TP), which is the global “roof of the world”, but the concentrations were low (0.115–6.34 ng/L and 0.115–1.24 ng/L, respectively). Local human activities and surface runoff were the main sources of PFASs in the surface water of the Tibetan Plateau. In addition, under the influence of the Southeast Asian monsoon in summers, marine aerosols from the Indian Ocean and air pollutants from human activities in Southeast Asia and South Asia will also enter the water bodies through dry and wet depositions. With the melting of glaciers caused by global warming, the concentration of PFASs in the surface water of the TP was higher than that before the melting of glaciers flowed into the surface water of the TP. Generally, this study summarized the existing research progress of PFAS studies on surface water and precipitation in China and identified the research gaps, which deepened the researchers’ understanding of this field and provided scientific support for related research in the future. The concentrations of PFASs in the water bodies after flowing through FMFs were significantly higher than those before water flowed through FMFs, so the discharge of the FMF production process was one of the main sources of PFASs in surface water. Full article

Based on the data from a French outbreak of legionellosis, a probabilistic approach was developed to analyze and assess the potential role of several suspected sources of contamination. Potential dates of exposure of all cases were determined using back-calculation, using two probability distribution functions to model incubation period. A probabilistic analysis and risk assessment were then used to determine the most probable sources of contamination for each wave of the outbreak. The risk assessment was based on parameters representing emission and dispersion of Legionella: level and duration of emission; aerosol dispersion capacity; and probability of potential exposure for each patient. Four types of facilities containing the Legionella epidemic strain were analyzed: cooling towers, aerated wastewater basins, high pressure water cleaners, and car wash stations. The results highlighted the potential role of an aerated wastewater basin in the outbreak in addition to cooling towers. The role of high-pressure water cleaners and car wash stations appeared to be non-significant. This study also reveals the lack of knowledge on facility parameters that can be useful for microbial risk assessments. This type of probabilistic analysis can be used to quantitatively assess the risk for various facilities in order to manage a legionellosis outbreak. Full article