Search Results (195)

Validating the potential of multi-frequency synthetic aperture radar (SAR) data for multi-layer and profile soil moisture (SM) estimation modeling, we conducted an airborne multi-frequency SAR joint observation experiment (AMFSEX) over the Liao River Basin in China. The experiment simultaneously acquired airborne high spatial resolution quad-polarization (quad-pol) SAR data at five frequencies, including the Ka-, X-, C-, S-, and L-band. A preliminary “vegetation–soil” parameter estimation model based on the multi-frequency SAR data was established. Theoretical penetration depths of the multi-frequency SAR data were analyzed using the Dobson empirical model and the Hallikainen modified model. On this basis, a water cloud model (WCM) constrained by multi-polarization weighted and penetration depth weighted parameters was used to analyze the estimation accuracy of the multi-layer and profile SM (0–50 cm depth) under different vegetation types (grassland, farmland, and woodland). Overall, the estimation error (root mean square error, RMSE) of the surface SM (0–5 cm depth) ranged from 0.058 cm³/cm³ to 0.079 cm³/cm³, and increased with radar frequency. For multi-layer and profile SM (3 cm, 5 cm, 10 cm, 20 cm, 30 cm, 40 cm, 50 cm depth), the RMSE ranged from 0.040 cm³/cm³ to 0.069 cm³/cm³. Finally, a multi-input multi-output regression model (Gaussian process regression) was used to simultaneously estimate the multi-layer and profile SM. For surface SM, the overall RMSE was approximately 0.040 cm³/cm³. For multi-layer and profile SM, the overall RMSE ranged from 0.031 cm³/cm³ to 0.064 cm³/cm³. The estimation accuracy achieved by coupling the multi-source data (multi-frequency SAR data, multispectral data, and soil parameters) was superior to that obtained using the SAR data alone. The optimal SM penetration depth varied across different vegetation cover types, generally falling within the range of 10–30 cm, which holds true for both the scattering model and the regression model. This study provides methodological guidance for the development of multi-layer and profile SM estimation models based on the multi-frequency SAR data. Full article

Deep learning has shown significant potential in multi-band Polarimetric Synthetic Aperture Radar (PolSAR) land cover classification. However, the existing methods face two main challenges: accurately modeling the complex nonlinear relationships between multiple bands and balancing classifier parameter efficiency with classification accuracy. To address these challenges, this paper proposes a novel decision-level multi-band fusion framework that leverages the synergistic optimization of the Vision Transformer (ViT) and Kolmogorov–Arnold Network (KAN). This innovative architecture effectively captures global spatial–spectral correlations through ViT’s cross-band self-attention mechanism and achieves parameter-efficient decision-level probability space mapping using KAN’s spline basis functions. The proposed method significantly enhances the model’s generalization capability across different band combinations. The experimental results on the quad-band (P/L/C/X) Hainan PolSAR dataset, acquired by the Aerial Remote Sensing System of the Chinese Academy of Sciences, show that the proposed framework achieves an overall accuracy of 96.24%, outperforming conventional methods in both accuracy and parameter efficiency. These results demonstrate the practical potential of the proposed method for high-performance and efficient multi-band PolSAR land cover classification. Full article

Multi-aspect synthetic aperture radar (SAR) is an emerging observation mode in SAR. Through multi-aspect observations, along with coherent and incoherent image processing, multi-aspect SAR effectively addresses issues like layovers, shadows, and foreshortening in conventional SAR. It can obtain multi-aspect scattering images of the observed scene. Modeling the statistical distribution characteristics of multi-aspect SAR images is crucial for its processing and applications. Currently, there is no comprehensive and systematic study on the statistical distribution characteristics of multi-aspect SAR images. Therefore, this paper conducts qualitative and quantitative analyses of these characteristics. Furthermore, we investigate the applicability and limitations of five single-parametric models commonly used in conventional SAR for modeling the statistical distribution characteristics of multi-aspect SAR images. The experimental results show that none of these models could accurately model the multi-aspect SAR images. To address this issue, we propose a finite mixture model (FMM) and evaluate its feasibility to accurately model the statistical distribution characteristics of multi-aspect SAR on X-band GOTCHA data and C-band Zhuhai data. The experimental results demonstrate that, compared with the single-parametric models, our method can accurately model the statistical distribution characteristics of various types of targets in multi-aspect SAR images from different observation aspects and aperture angles in various bands. Full article

Synthetic aperture radar (SAR) technology is one of the imaging radar technologies receiving the most attention worldwide. The main purpose is to detect targets in the area of interest in different settings, such as day/night, various weather conditions, etc. Phase gradient autofocusing (PGA) algorithms have been widely used for autofocus in SAR imaging. Conventional PGA methods in stripmap SAR apply dechirping to switch the range-compressed phase history-domain signal to a form equivalent to that in spotlight mode. However, this switching method has inherent limitations in phase error estimation, leading to degraded autofocusing performance. To address this issue, we introduce an FrFT-based switching method that provides more precise and fast autofocus. Additionally, this method enables effective detection and extraction of moving targets in the environment where moving targets are present. Moving targets introduce additional phase errors that hinder accurate autofocus, making it essential to isolate and process them separately. We carried out practical experiments with an X-band chirp pulse SAR system to verify the proposed method and mount the system on an automobile. Full article

Spaceborne Synthetic Aperture Radar (SAR) is extensively used in maritime surveillance due to its ability to monitor vast oceanic regions regardless of weather conditions and sun illumination. Over the years, numerous automatic ship detection algorithms have been developed, utilizing either single-polarimetric data (i.e., intensity) or leveraging additional information provided by polarimetric sensors. One of the main challenges in automatic ship detection using SAR is that sea clutter, influenced primarily by sea conditions and image acquisition angles, can exhibit strong backscatter, reducing the signal-to-clutter ratio (that is, the contrast) between ships and their surroundings. This leads inevitably to detection errors, which can be either false alarms or miss-detections. A potential solution to this issue is to develop methodologies that suppress backscattered signals from the sea while preserving the radar returns from ships. In this work, we analyse a contrast enhancement method which is designed to suppress unwanted sea clutter while preserving signals from potential ships. A key advantage of this method is that it is fully analytical, eliminating the need for numerical optimization and enabling the rapid generation of an enhanced image better suited for automatic detection. This technique, based on polarimetric orthogonality, was originally formulated for quad-polarimetric data, and here the adaptation for dual-polarimetric SAR images is also detailed. To demonstrate its effectiveness, a comprehensive set of results using both quad- and dual-polarimetric images acquired by various sensors operating at L-, C-, and X-band is presented. Full article

Aboveground biomass (AGB) is crucial in forest ecosystems and is intricately linked to the carbon cycle and global climate change dynamics. This study investigates the efficacy of synthetic aperture radar (SAR) data from the X, C, and L bands, combined with Sentinel-2 optical imagery, vegetation indices, gray-level co-occurrence matrix (GLCM) texture metrics, and topographical variables in estimating AGB in the Küre Mountains National Park, Türkiye. Four machine-learning regression models were employed: partial least squares (PLS), least absolute shrinkage and selection operator (LASSO), multivariate linear, and ridge regression. Among these, the PLS regression (PLSR) model demonstrated the highest accuracy in AGB estimation, achieving an R² of 0.74, a mean absolute error (MAE) of 28.22 t/ha, and a root mean square error (RMSE) of 30.77 t/ha. An analysis across twelve models revealed that integrating ALOS-2 PALSAR-2 and SAOCOM L-band satellite data, particularly the SAOCOM HV and ALOS-2 PALSAR-2 HH polarizations with optical imagery, significantly enhances the precision and reliability of AGB estimations. Full article

This paper describes a flexible and seamless processor for Unmanned Aerial Vehicle (UAV)-borne Synthetic Aperture Radar (SAR) imagery. When designing a focusing algorithm for large-scale and high-resolution SAR images, efficiency and accuracy are two mandatory aspects to consider. The proposed processing scheme is based on a modified version of Fast Factorized Back-Projection (FFBP), in which the factorization procedure is interrupted on the basis of a computational cost analysis to reduce the number of complex operations at its minimum. The algorithm gains efficiency in the case of low-altitude platforms, where there are significant variations in azimuth resolution, but not in the case of conventional airborne missions, where the azimuth resolution can be considered constant in the swath. The algorithm’s performance is derived by assessing the number of complex operations required to focus an SAR image. Two scenarios are tackled in a numerical simulation: a UAV-borne SAR with a short synthetic aperture and a wide field of view, referred to as the ground-based-like (GBL) scenario, and a classical stripmap scenario. In both cases, we consider mono-static and bi-static radar configurations. The results of the numerical simulations show that the proposed algorithm outperforms FFBP in the stripmap scenario while achieving the same performance as FFBP in the GBL scenario. In addition, the algorithm is validated thanks to an experimental UAV-borne SAR campaign in the X-band. Full article

The Interferometric Synthetic Aperture Radar (InSAR) has significantly advanced in its usage for analyzing surface information such as displacement or elevation. In this study, we evaluated a digital elevation model (DEM) constructed using X-band KOMPSAT-5 interferometric datasets provided by the Korea Aerospace Research Institute (KARI). The 28-day revisit cycle of KOMPSAT-5 poses challenges in maintaining interferometric correlation. To address this, four KOMPSAT-5 images were employed in a multi-baseline interferometric approach to mitigate temporal decorrelation effects. Despite the slightly longer temporal baselines, the analysis revealed sufficient coherence (>0.8) in three interferograms. The height of ambiguity ranged from 59 to 74 m, which is a moderate height of sensitivity to extract topography over the study area of San Francisco in the USA. Unfortunately, only ascending acquisition mode datasets were available for this study. The derived DEM was validated against three reference datasets: Copernicus GLO-30 DEM, ICESat-2, and GEDI altimetry. A high coefficient of determination (R² > 0.9) demonstrates the feasibility of the interferometric application of KOMPSAT-5. Full article

The exchange of water, sediment, and nutrients in wetlands occurs through a complex network of channels and overbank flow. Although optical sensors can map channels at high resolution, they fail to identify narrow intermittent channels colonized by vegetation. Here we demonstrate an innovative application of rapid-repeat interferometric synthetic aperture radar (InSAR) to study hydrologic connectivity and tidal influences in Louisiana’s coastal wetlands, which can provide valuable insights into water flow dynamics, particularly in vegetation-covered and narrow channels where traditional optical methods struggle. Data used were from the airborne UAVSAR L-band sensor acquired for the Delta-X mission. We applied interferometric techniques to rapid-repeat (~30 min) SAR imagery of the southern Atchafalaya basin acquired during two flights encompassing rising-to-high tides and ebbing-to-low tides. InSAR coherence is used to identify and differentiate permanent open water channels from intermittent channels in which flow occurs underneath the vegetation canopy. The channel networks at rising and ebbing tides show significant differences in the extent of flow, with vegetation-filled small channels more clearly identified at rising-to-high tide. The InSAR phase change is used to identify locations on channel banks where overbank flow occurs, which is a critical component for modeling wetland hydrodynamics. This is the first study to use rapid-repeat InSAR to monitor tidal impacts on water flow dynamics in wetlands. The results show that the InSAR method outperforms traditional optical remote sensing methods in monitoring water flow in vegetation-covered wetlands, providing high-resolution data to support hydrodynamic models and critical support for wetland protection and management. Full article

In this work, we present the results of a comparative analysis between the first-generation Advanced Synthetic Aperture Radar (ASAR) sensor mounted on board the ENVISAT platform and the novel ICEYE micro-satellite synthetic aperture radar (SAR) sensor in measuring the radial velocity of ocean currents through the Doppler Centroid Anomaly (DCA) technique. First, the basic principles of DCA and the theoretical precision of the Doppler Centroid (DC) estimates are introduced. Subsequently, the role of the DC measurements in retrieving the sea surface current velocity is addressed. To achieve this goal, two sets of SAR data gathered by ASAR (C-band) and from the X-band ICEYE instruments, respectively, are exploited. The standard deviation of DCA measurements is derived and tested against what is expected by theory. The presented analysis results are beneficial to evaluate the pros and cons of the new-generation X-band to the first-generation ASAR/ENVISAT system, which has been extensively exploited for ocean currents monitoring applications. As an outcome, we find that with inherently selected methods for DC estimates, the performance offered by ICEYE is comparable to, or even better than (with specific parameters selection), the consolidated approaches based on the ASAR sensor. Nonetheless, new SAR constellations offer an undoubted advantage regarding improved spatial resolution and time repeatability. Full article

In the field of target detection using synthetic aperture radar (SAR) images, deep learning-based supervised learning methods have demonstrated outstanding performance. However, the effectiveness of deep learning methods is largely influenced by the quantity and diversity of samples in the dataset. Unfortunately, due to various constraints, the availability of labeled image data for training SAR vehicle detection networks is quite limited. This scarcity of data has become one of the main obstacles hindering the further development of SAR vehicle detection. In response to this issue, this paper collects SAR images of the Ka, Ku, and X bands to construct a labeled dataset for training Stable Diffusion and then propose a framework for data augmentation for SAR vehicle detection based on the Diffusion model, which consists of a fine-tuned Stable Diffusion model, a ControlNet, and a series of methods for processing and filtering images based on image clarity, histogram, and an influence function to enhance the diversity of the original dataset, thereby improving the performance of deep learning detection models. In the experiment, the samples we generated and screened achieved an average improvement of 2.32%, with a maximum of 6.6% in $mA{P}_{75}$ on five different strong baseline detectors. Full article

Urban areas face an imminent risk of collapse due to structural deficiencies and gradual ground subsidence. Therefore, monitoring surface movements is crucial for detecting abnormal behavior, implementing timely preventive measures, and minimizing the detrimental effects of this phenomenon in residential regions. In this context, interferometric synthetic aperture radar (InSAR) has emerged as a highly effective technique for monitoring slow and long-term ground hazards and surface motions. The first goal of this study is to explore the potential applications of persistent scatterer interferometry (PSI) and small baseline subset (SBAS) algorithms in collapse hotspot detection, utilizing a dataset consisting of 144 Sentinel-1 images. The experimental results from three areas with a history of collapses demonstrate that the SBAS algorithm outperforms PSI in uncovering behavior patterns indicative of collapse and accurately pinpointing collapse points near real collapse sites. In the second phase, this research incorporated an additional dataset of 36 TerraSAR-X images alongside the Sentinel-1 data to compare results based on radar images with different spatial resolutions in the C and X bands. The findings reveal a strong correlation between the TerraSAR-X and Sentinel-1 time series. Notably, the analysis of the TerraSAR-X time series for one study area identified additional collapse-prone points near the accident site, attributed to the higher spatial resolution of these data. By leveraging the capabilities of InSAR and advanced algorithms, like SBAS, this study highlights the potential to identify areas at risk of collapse, enabling the implementation of preventive measures and reducing potential harm to residential communities. Full article

This article introduces a small microwave remote sensing satellite weighing 310 kg, operating in low earth orbit (LEO). It is equipped with an X-band synthetic aperture radar (SAR) antenna, capable of a maximum imaging resolution of 0.6 m. To achieve the objectives of lower cost, reduced weight, minimized power consumption, and enhanced temperature stability, an optimized thermal design method tailored for satellites has been developed, with a particular focus on SAR antennas. The thermal control method of the antenna is closely integrated with structural design, simplifying the thermal design and its assembly process, reducing the resource consumption of thermal control systems. The distribution of thermal interface material (TIM) in the antenna assembly has been carefully calculated, achieving a zero-consumption thermal design for the SAR antenna. And the temperature difference of the entire antennas when powered on and powered off would not exceed 17 °C, meeting the specification requirements. In addition, to ensure the accuracy of antenna pointing, the support plate of antennas requires stable temperature. The layout of the heaters on the board has been optimized, reducing the use of heaters by 30% while ensuring that the temperature variation of the support board remains within 5 °C. Then, an on-orbit thermal simulation analysis of the satellite was conducted to refine the design and verification. Finally, the thermal test of the SAR satellite under vacuum conditions was conducted, involving operating the high-power antenna, verifying that the peak temperature of T/RM is below 29 °C, the temperature fluctuation amplitude during a single imaging task is 10 °C, and the lowest temperature point of the support plate is 16 °C. The results of the thermal simulation and test are highly consistent, verifying the correctness and effectiveness of the thermal design. Full article

In this work, the airborne Synthetic Aperture Radar (SAR) infrastructure developed at the Institute for Electromagnetic Sensing of the Environment (IREA) of the National Research Council of Italy (CNR) is described. This infrastructure allows IREA-CNR to plan and execute airborne SAR campaigns and to process the acquired data with a twofold aim. On one hand, the aim is to develop research activities; on the other hand, the aim is to support the emergency prevention and management activities of the Department of Civil Protection of the Italian Presidency of the Council of Ministers, for which IREA-CNR serves as National Centre of Competence. Such infrastructure consists of a flight segment and a ground segment that include a multi-frequency airborne SAR sensor based on the Frequency-Modulated Continuous Wave (FMCW) technology and operating in the X- and L-bands, an Information Technology (IT) platform for data storage and processing and an airborne SAR data processing chain. In this work, the technical aspects related to the flight and ground segments of the infrastructure are presented. Moreover, a discussion on the response times and characteristics of the final products that can be achieved with the infrastructure is provided with the aim of showing its capabilities to support the monitoring activities required in a possible emergency scenario. In particular, as a case study, the acquisition and subsequent interferometric processing of airborne SAR data relevant to the Stromboli volcanic area in the Sicily region, southern Italy, are presented Full article

The range–Doppler (R–D) model is extensively employed for the geometric processing of synthetic aperture radar (SAR) images. Refining the sensor motion state and imaging parameters is the most common method for achieving high-precision geometric processing using the R–D model, comprising a process that involves numerous parameters and complex computations. In order to reduce the specialization and complexity of parameter optimization in the classic R–D model, we introduced a novel approach called ICRD (image compensation-based range–Doppler) to improve the positioning accuracy of the R–D model, implementing a low-order polynomial to compensate for the original imaging errors without altering the initial positioning parameters. We also designed low-order polynomial compensation models with different parameters. The models were evaluated on various SAR images from different platforms and bands, including spaceborne TerraSAR-X and Gaofen3-C images, manned airborne SAR-X images, and unmanned aerial vehicle-mounted miniSAR-Ku images. Furthermore, image positioning experiments involving the use of different polynomial compensation models and various numbers and distributions of ground control points (GCPs) were conducted. The experimental results demonstrate that geometric processing accuracy comparable to that of the classical rigorous positioning method can be achieved, even when applying only an affine transformation model to the images. Compared to classical refinement models, however, the proposed image-compensated R–D model is much simpler and easy to implement. Thus, this study provides a convenient, robust, and widely applicable method for the geometric-positioning processing of SAR images, offering a potential approach for the joint-positioning processing of multi-source SAR images. Full article