Search Results (430)

Indonesia is among the most landslide-prone countries in the world, with thousands of fatalities and widespread infrastructure damage recorded over recent decades. Despite this high hazard level, regional-scale landslide monitoring remains constrained by the limitations of conventional bitemporal satellite imagery, which is susceptible to cloud contamination, dependent on precise acquisition timing, and unable to capture the full temporal dynamics of landslide occurrence and recovery. While the LandTrendr (Landsat-based Detection of Trends in Disturbance and Recovery) algorithm has been widely applied for detecting vegetation disturbances such as forest loss and land-use change, its potential for landslide detection in tropical environments has not been sufficiently explored. This study aims to evaluate the applicability of LandTrendr applied to long-term Landsat time series imagery for automated regional-scale landslide detection and mapping in Indonesia. The method integrates temporal segmentation of the Normalized Difference Vegetation Index (NDVI) derived from Landsat imagery spanning 2000–2022 with slope information from the Shuttle Radar Topography Mission (SRTM) Digital Elevation Model (DEM) to identify the characteristic drop-recovery spectral signature associated with landslide events. The algorithm was applied and evaluated in two geologically distinct study areas: Lombok, West Nusa Tenggara, and Pasaman, West Sumatra. Detection accuracies of 25.9% by location and 20.3% by area were achieved in Lombok and 76.3% by location and 85.3% by area in Pasaman. The lower accuracy in Lombok is primarily attributed to the predominance of small landslides below the sensor’s spatial resolution and rapid vegetation recovery. The proposed approach demonstrates the unique capability of LandTrendr to model the entire life cycle of a mass movement event, from pre-event stability through abrupt disturbance to ecological recovery within a single unified framework, providing a scalable and cost-effective tool for long-term landslide monitoring applicable to other tropical, landslide-prone regions. Full article

Global Digital Elevation Models (DEMs) exhibit systematic biases constrained by acquisition geometry and surface penetration. This study aims to evaluate whether the increasing complexity of geometric deep learning (e.g., Graph Neural Networks, GNNs) is justified by performance gains over established feature engineering paradigms (e.g., XGBoost) under the constraints of sparse altimetry supervision. We established a rigorous comparative framework across four mainstream products—ALOS World 3D, Copernicus DEM, SRTM GL1, and TanDEM-X—using Sichuan Province, China, as a representative natural laboratory. Our results reveal a fundamental scale mismatch (where the ~485 m average spacing of sampled altimetry footprints dwarfs the local terrain resolution): despite their topological complexity, Hybrid GNN models fail to establish a statistically significant accuracy advantage over the systematically optimized XGBoost baseline, demonstrating RMSE parity. Mechanistically, we uncover a critical divergence in decision logic: XGBoost relies on a stable “Physics Skeleton” consistently dominated by deterministic features (terrain aspect and vegetation density), whereas GNNs exhibit severe “Attribution Stochasticity” ($\rho \approx$ 0.63–0.77). The GNN component acts as a residual-dependent latent feature learner rather than discovering universal topological laws. We conclude that for geospatial regression tasks relying on sparse supervision, “Physics Trumps Geometry.” A “Feature-First” paradigm that prioritizes robust, domain-knowledge-based physical descriptors outweighs the indeterminate complexity of “Black Box” architectures. This study underscores the imperative of prioritizing explanatory stability over marginal accuracy gains to foster trusted Geo-AI. Full article

Coffee, as a perennial commodity crop, plays a crucial role in global agricultural markets, regional livelihoods, and poverty alleviation. Yunnan Province of China (21°8′–29°15′N) represents the northernmost coffee-growing region worldwide, and its production has gained increasing attention in international markets. However, the absence of a spatially explicit and high-resolution coffee distribution dataset has constrained environmental assessment, land-use analysis, and policy-making in this subtropical and marginal growing region. In this study, we developed the first 10 m resolution Arabica coffee distribution dataset for Yunnan Province for the year 2023 using Sentinel-2 optical imagery and Shuttle Radar Topographic Mission (SRTM) terrain data within the Google Earth Engine (GEE) platform. An object-based workflow was implemented to generate spatially coherent mapping units, followed by supervised classification to identify coffee plantations. The resulting map achieved an overall accuracy (OA) of 0.87, with user accuracy (UA), producer accuracy (PA), and F1 score of 0.90, 0.96, and 0.93 for the coffee class, demonstrating its reliability for regional-scale applications. Feature contribution analysis indicates that shortwave infrared (SWIR) and red-edge information, particularly during the dry season, plays an important role in coffee discrimination. These results enhance confidence in the ecological relevance and stability of the mapping framework. The proposed workflow provides a practical and transferable approach for perennial crop mapping in complex mountainous environments. More importantly, the generated high-resolution coffee distribution dataset establishes a spatial baseline for monitoring land-use dynamics, assessing ecological impacts, and supporting sustainable coffee development in southwestern China. Full article

Forecasting monthly precipitation in mountainous terrain poses challenges that push conventional deep learning approaches to their limits: convective processes operate locally while orographic effects span entire drainage basins. We compare three architecture families on precipitation prediction across the Colombian Andes: ConvLSTM (convolutional recurrent), FNO-ConvLSTM (spectral–temporal), and GNN-TAT (graph attention LSTM). Using CHIRPS v2.0 and SRTM topography for Boyacá department (61 × 65 grid, 3965 nodes), we evaluate 39 configurations across feature bundles (BASIC, KCE elevation clusters, and PAFC autocorrelation lags) and horizons from 1 to 12 months. GNN-TAT matches ConvLSTM accuracy ($R^2$: 0.628 vs. 0.642; RMSE: 82.29 vs. 79.40 mm) with 95% fewer parameters (∼98K vs. 2.1M). Across configurations, GNN-TAT produces a lower mean RMSE (92.12 vs. 112.02 mm; $p=0.015$) and a 74.7% lower variance. The explicit graph structure, with edges weighted by elevation similarity, appears to reduce sensitivity to hyperparameter choices. Pure FNO struggles with precipitation’s spatial discontinuities ($R^2=0.206$), though adding a ConvLSTM decoder recovers much of the lost skill ($R^2=0.582$). Elevation clustering improves GNN-TAT significantly ($p=0.036$) but not ConvLSTM, suggesting that feature design should match the spatial encoding paradigm. ConvLSTM achieves peak accuracy on local patterns; GNN-TAT provides robust predictions with interpretable spatial reasoning. These complementary strengths motivate stacking ensembles that combine grid-based and graph-based representations. Full article

Two-dimensional phase unwrapping (PU) of interferometric synthetic aperture radar (InSAR) data remains difficult when steep deformation gradients and multi-source disturbances violate the Itoh condition. This study proposes FPUNet, a Fourier-enhanced encoder–decoder for joint denoising and 2-D PU, in which frequency-domain global context modeling is combined with complementary multi-scale spatial aggregation and attention-based feature refinement. Specifically, the bottleneck cascades a Fourier Mixed Residual Block (FMRB), atrous spatial pyramid pooling (ASPP), and a convolutional block attention module (CBAM) to suppress noise while preserving deformation-related fringe structures. FPUNet is trained end-to-end on realistically simulated Sentinel-1 interferograms generated from Shuttle Radar Topography Mission (SRTM) digital elevation models using a physics-informed composite loss that enforces data fidelity, gradient consistency, spectral regularization, and selective rewrapping consistency. On a synthetic benchmark of 1800 test interferograms, FPUNet achieves an RMSE of 0.79 rad, improving over a plain U-Net (1.61 rad) and producing fewer large fringe-number errors than least-squares, SNAPHU, PUNet, and DLPU. Experiments on real Sentinel-1 data over the Datong mining area and the 2022 Menyuan and Luding earthquakes further indicate improved phase closure and rewrapping consistency, particularly in high-gradient coseismic fringes, supporting FPUNet as a robust PU module for InSAR deformation monitoring. Full article

In arid-zone water resource management and water-security assessment, changes in water-body volume are key indicators of water availability and regulation performance. However, arid-zone lakes often lack sufficient bathymetric information to constrain geometry under low lake-level conditions. Shrinkage-driven hydrological disconnection can destabilize extrapolation of water level–storage relationships. This increases uncertainty in quantifying long-term storage changes. Here, we develop a multi-digital elevation model (DEM) hypsometry framework to reconstruct near-monthly lake storage for 1993–2024, recovering storage during low-level periods without bathymetric surveys. Reconstructed changes agree with independent satellite altimetry (r = 0.93 for level and 0.90 for storage), outperforming above-water-only (r ≈ 0.637 for water level) and conventional model-selection base-lines (r ≈ 0.753 for water level). The framework was quantified across three scenarios: expanding lakes, lake systems and reservoirs, and terminally shrinking lakes. For the persistently shrinking Big Aral Sea, under the whole-lake modeling assumption, the Copernicus-based reconstruction provides a cumulative storage change of −214.3 km³, closest to the satellite altimetry estimate of −210.68 km³ among the tested DEMs. In contrast, other DEMs overestimate the 1993–2024 cumulative loss by 66.15–141.01 km³. Sub-lake modeling further adjusts the Shuttle Radar Topography Mission (SRTM)-based cumulative change to −248.38 km³, substantially reducing structural bias caused by lake disconnection. This study provides a transferable technical framework for lake storage reconstruction in arid regions under degraded low lake-level conditions and hydrological disconnection. Full article

We assessed the vertical accuracy of six global digital elevation models—FABDEM (SRTM-enhanced), SRTM, ASTER GDEM, ALOS AW3D30, DeltaDTM and GEDTM—against a local photogrammetry-derived DEM as a benchmark in a flat coastal plain of the Colombian Caribbean. Using GNSS-RTK ground points and a high-accuracy reference DEM, we computed BIAS, RMSE, and MAE. Errors were analyzed by land cover class and along transverse profiles relative to the reference DEM. We also evaluated hydrologic suitability by comparing flow accumulation and drainage patterns derived from each model, treating the photogrammetry-derived model as the control and the global DEMs as treatments to gauge their ability to represent hydraulic/hydrologic behavior. DeltaDTM, GEDTM and FABDEM showed the best overall performance, with the lowest vertical error (particularly in non-urban areas with sparse vegetation) and the highest drainage agreement, along with their flood extent sensitivity to a 0.5 m water level rise, all of which were comparable to the benchmark. These results provide practical guidance for selecting and preprocessing topographic models for risk management and territorial planning in flat regions. Full article

Land degradation (LD) is an emerging threat of the decade that is not only deteriorating arable lands globally but also threatening global ecosystem sustainability. Therefore, the intensification of LD has stimulated global governing bodies and researchers to undertake initiatives against this dilemma through sustainable and eco-friendly approaches. Geographical mapping is critical in analysing land formation, soil composition and land use patterns, subsequently facilitating data-driven planning for soil conservation. In this review, Geographic Information System (GIS) technology, combined with Shuttle Radar Topography Mission (SRTM) data, is used to explore soil properties and land use patterns across Saudi Arabia, with a focus on soil types, soil thickness, and soil uses. Spatial analyses indicate that the most predominant soil type in the country is sandy, followed by loam and sandy loam. The soil depth distribution exhibits a notably bimodal pattern, with large areas characterized by shallow soils (0–4 m) and deep soils (43–50 m). These spatial visualizations provide valuable insights into soil heterogeneity, supporting evidence-based, site-specific strategies for sustainable land management. This study also outlines the major land degradation pathways affecting arable lands in Saudi Arabia and describes how these pathways can be used to assess the extent of land loss. Besides land loss pathways, the current study also explains the most suitable mitigation strategies, including mulching, cover cropping, and agroforestry, as well as how international governing bodies like the UNDP, UNEP, FAO, and World Bank can contribute to the mitigation of LD in Saudi Arabia. However, further studies are required to assess the intensity of these solutions for each soil type and thickness under different climatic conditions. Full article

The accuracy of forest canopy height estimation is crucial for forest resource management and ecosystem carbon sequestration. However, existing approaches often face limitations in effectively integrating multisource remote sensing data, feature representation, and model learning strategies. To enhance the prediction performance of the model in complex terrain and multisource data environments, this study comprehensively used ICESat-2/ATLAS photon point clouds, Sentinel-2/MSI multispectral imagery, and SRTM-DEM to construct a remote sensing-driven multisource feature system, which eliminated redundant interference using permutation feature importance analysis. Additionally, a self-attention (SA) mechanism was introduced to strengthen high-dimensional feature representation. Three heterogeneous models, incorporating deep neural network (DNN), extreme gradient boosting (XGBoost), and residual network (ResNet), were independently applied for forest canopy height estimation and were further used as base learners, with a random forest as the meta-learner, and an SA-Blending heterogeneous ensemble model that combines a blending technique with an SA mechanism was proposed to enhance the accuracy of forest canopy height estimation. To evaluate the SA optimization strategy and the role of multisource fusion, this study used the original features, SA-optimized features, and multisource fusion features (i.e., the concatenation and fusion of original features and self-attention mechanism features) as inputs to comprehensively compare the performance of each single model and the integrated model. The results show that: (1) The self-attention mechanism significantly improves the prediction performance of heterogeneous models. Compared with original features inputs, the R² of DNN (SA-Only) and XGBoost (SA-Only) increased to 0.706 and 0.708, respectively, and the RMSE decreased to 1.691 m and 1.613 m. Although the R² for ResNet (SA-Only) decreased slightly to 0.699 and the RMSE increased to 1.712 m, the overall impact was not significant. (2) Under the condition of multisource fusion feature input, DNN+SA, XGBoost+SA, and ResNet+SA all demonstrated higher fitting accuracy and stability, verifying the enhancing effect of the SA mechanism on the association expression of multisource information. (3) The SA-Blending model achieved the best overall performance, with R² of 0.766 and RMSE of 1.510 m. It outperformed individual models and the SA-optimized model in terms of overall accuracy, stability, and robustness. The results can provide technical support for high-precision forest canopy height mapping and are of great significance for ecological monitoring applications. Full article

Understanding landform evolution is essential for assessing how terrain responds to geomorphic drivers such as weathering, fluvial erosion, hillslope processes, and tectonic uplift. This is particularly important in applications such as constructed post-mining landform rehabilitation, where predicting long-term erosional stability is vital for sustainable closure planning. In addition to long-term average erosion rates, the spatial patterns of gullies, rills, and channels are critical for assessing landform stability. This review examines Digital Elevation Model (DEM)—driven, process-based Landform Evolution Models (LEMs), with a primary focus on SIBERIA, CAESAR-Lisflood, and SSSPAM, which are widely used to evaluate the erosional behaviour of constructed post-mining landforms, each with distinct characteristics. These models are systematically compared in terms of input requirements, process representations, parameterisation, and predictive capabilities. Recent advances in high-spatial resolution DEMs (e.g., LiDAR, SRTM), along with digital soil and rainfall databases and satellite-derived vegetation indices, have improved the parameterisation of erosion, hydrological, and sediment-transport processes of the LEMs. A brief comparative case study is presented to demonstrate how these LEMs simulate 1000-year erosional behaviour along a linear hillslope. This review synthesises the current capabilities and limitations of DEM-driven LEMs, providing guidance for researchers, land managers, and practitioners in selecting appropriate models to support sustainable post-mining landform management, as well as outlining potential future advancements. Full article

This study utilizes Digital Elevation Models (DEMs) with different spatial resolutions (SRTM 90 m, ASTER DEM 30 m, and ALOS PALSAR 12.5 m), Landsat-8 satellite imagery, and the Bouguer WGM-12 gravity model to analyze morphotectonic features in the Upper Guajira region of Colombia, a desert area in northern South America, area that is composed by low-relief serranías of Cabo de la Vela, Carpintero, Cosinas, Simarua, Jarara, and Macuira. Three DEMs were used to extract and map morphotectonic lineaments, drainage networks, and morphological features. Lineaments were characterised by azimuth frequency, length, density, lithological distributions, and geological timeframes, with support from a digitized geological map from the Colombian Geological Service (SGC). The analysis of the east–west (E-W) Cuisa fault, using the Riedel shear model, suggests a transtensional/transpressional tectonic regime influenced by the Caribbean and South American plates, characterised by NE-SW and E-W fault orientations. Lineaments were grouped into five geochronological categories based on the geological map, revealing a shift from NE-SW to E-W orientations from the Cretaceous period onward, reflecting the ongoing movement of the Caribbean plate. Folds and faults from this tectonic activity were enhanced using Landsat-8 band combinations. The WGM-12 model was separated into regional and residual signals, with the latter highlighting the serranías subregions. Residual gravity analysis revealed significant negative anomalies, suggesting lower-density lithologies surrounded by higher-density blocks. This pattern aligns with the regional geological framework and may reflect a crustal root or terrain dragging linked to the tectonic processes that shaped the serranías. Derivative residual gravity data also revealed lineaments oriented NE–SW, whose distribution extends beyond the morphometric boundaries of the subregions. The study found a strong correlation between structural and drainage patterns, demonstrating structural control over geomorphology. This study establishes a solid morphotectonic and geophysical framework for the Upper Guajira region, demonstrating how multi-resolution DEM analysis combined with gravity data can resolve regional deformation patterns, crustal architecture, and tectonic development along the Caribbean–South American plate boundary. Full article

High-resolution TIR missions require sustained and well-characterized radiometric accuracy to support applications such as land surface temperature retrieval, drought monitoring, and surface energy budget analysis. To address this need, we develop an operational and automated ground-based vicarious radiometric calibration framework for TIR sensors and demonstrate its performance using the Wide-swath Thermal Infrared Imager (WTI) onboard Gaofen-5 01A (GF-5A). Three arid Gobi calibration sites were selected by integrating Moderate Resolution Imaging Spectroradiometer (MODIS) cloud products, Shuttle Radar Topography Mission (SRTM)-derived topography, and WTI-based radiometric uniformity metrics to ensure low cloud cover, flat terrain, and high spatial homogeneity. Automated ground stations deployed at Golmud, Dachaidan, and Dunhuang have continuously recorded 1 min contact surface temperature since October 2023. Field-measured emissivity spectra, Integrated Global Radiosonde Archive (IGRA) radiosonde profiles, and MODTRAN (MODerate resolution atmospheric TRANsmission) v5.2 simulations were combined to compute top-of-atmosphere (TOA) radiances, which were subsequently collocated with WTI imagery. After data screening and gain-stratified regression, linear calibration coefficients were derived for each TIR band. Based on 189 scenes from February–July 2024, all four bands exhibit strong linearity (R-squared greater than 0.979). Validation using 45 independent scenes yields a mean brightness–temperature root-mean-square error (RMSE) of 0.67 K. A full radiometric-chain uncertainty budget—including contact temperature, emissivity, atmospheric profiles, and radiative transfer modeling—results in a combined standard uncertainty of 1.41 K. The proposed framework provides a low-maintenance, traceable, and high-frequency solution for the long-term on-orbit radiometric calibration of GF-5A WTI and establishes a reproducible pathway for future TIR missions requiring sustained calibration stability. Full article

Mountain Excavation and Land Creation Projects (MELCPs) have emerged as a critical strategy for expanding urban development space in mountainous regions facing land scarcity. Dynamic monitoring and risk management of these projects are essential for promoting sustainable urban development. This study develops an integrated monitoring framework for MELCPs by combining ascending and descending Sentinel-1 SAR data, Sentinel-2 optical imagery, SRTM digital elevation models (DEM), and field survey data. The framework incorporates multi-temporal change detection, random forest classification, and time-series InSAR analysis to systematically capture the spatiotemporal evolution and subsidence mechanisms associated with MELCPs. Key findings include: (1) The use of dual-orbit SAR data significantly improves the detection accuracy of excavation areas, achieving an overall accuracy of 87.1% (Kappa = 0.85) and effectively overcoming observation limitations imposed by complex terrain. (2) By optimizing the combination of spectral, texture, topographic, and polarimetric features using a random forest algorithm, the classification accuracy of MELCPs is enhanced to 91.2% (Kappa = 0.889). This enables precise annual identification of MELCP progression from 2017 to 2022, revealing a three-stage evolution pattern: concentrated expansion, peak activity, and restricted slowdown. Specifically, the reclaimed area increased from 2.66 km² (pre-2018) to a peak of 12.61 km² in 2021, accounting for 34.56% of the total area of the study region, before decreasing to 2.69 km² in 2022. (3) InSAR monitoring from 2017 to 2023 indicates that areas with only filling experience minor shallow subsidence (<50 mm), whereas subsequent building loads and underground engineering activities lead to continuous deep soil consolidation, with maximum cumulative subsidence reaching 333.8 mm. This study demonstrates that subsidence in MELCPs follows distinct spatiotemporal patterns and is predictable, offering important theoretical insights and practical tools for engineering safety management and territorial spatial optimization in mountainous cities. Full article

Vegetation degradation in arid and semi-arid regions is intensifying due to rising temperatures, declining rainfall, soil exposure, and persistent human pressures. Drylands cover over 41% of the global land surface and support nearly two billion people, making their degradation a major environmental and socio-economic concern. However, many remote sensing and GIS-based assessment approaches remain fragmented and difficult to reproduce. This study proposes a Computational Sustainability Framework for vegetation degradation assessment that integrates multi-source satellite data, biophysical indicators, automated geospatial preprocessing, and the Analytical Hierarchy Process (AHP) within a transparent and reproducible workflow. The framework comprises four phases: data preprocessing, indicator extraction and normalization, AHP-based modeling, and spatial classification with qualitative validation. The framework was applied to the Al-Khunfah and Harrat al-Harrah Protected Areas in northern Saudi Arabia using multi-source datasets for the January–April 2023 period, including Sentinel-2, Landsat-8, CHIRPS precipitation, ESA-CCI land cover, FAO soil data, and SRTM DEM. High degradation zones were associated with low NDVI (<0.079), high BSI (>0.276), and elevated LST (>49 °C), whereas low degradation areas were concentrated near wadis and relatively more fertile soils. Overall, the proposed framework provides a scalable and interpretable tool for early-stage vegetation degradation screening in arid environments, supporting the prioritization of areas for ecological investigation and restoration planning. Full article

The Synthetic Aperture Radar Interferometry (InSAR) technique enables researchers to generate Digital Elevation Models (DEMs) from SAR data, which researchers widely apply in multi-temporal analyses, including ground deformation monitoring, susceptibility mapping, and analysis of spatial changes in erosion basins. In this study, we generated two interferometric DEMs from Sentinel-1 (S1, VV polarization) and TerraSAR-X (TSX, HH polarization, ascending orbit) data, processed in SNAP, over a mountainous sector of the central Andes in Chile. We assessed the accuracy of the DEMs against two reference datasets: the SRTM DEM and a high-resolution LiDAR-derived DEM. We selected 150 randomly distributed points across different slope classes to compute statistical metrics, including RMSE and MedAE. Relative to the LiDAR DEM, both sensors yielded rMSE values of approximately 20 m, increasing to 23–24 m when compared with the SRTM DEM. The MedAE, a metric less sensitive to outliers, was 3.97 m for S1 and 3.26 m for TSX with respect to LiDAR, and 7.07 m for S1 and 7.49 m for TSX relative to SRTM. We observed a clear positive correlation between elevation error and terrain slope. In areas with slopes greater than 45°, the MedAE exceeded 14 m relative to the LiDAR DEM and reached ~15 m relative to the SRTM for both S1 and TSX. Full article