Search Results (13)

Improving photovoltaic (PV) panel performance under extreme climatic conditions is critical for advancing sustainable energy systems. In hyper-arid regions, elevated operating temperatures significantly reduce panel efficiency. This study investigates and compares three cooling techniques—air cooling, water cooling, and porous media cooling—using thermal and electrical modeling based on CFD simulations in ANSYS. The numerical model replicates a PV system operating under peak solar irradiance (900 W/m²) and realistic ambient conditions in Adrar, Algeria. Simulation results show that air cooling leads to a modest temperature reduction of 6 °C and a marginal efficiency gain of 0.25%. Water cooling, employing a top-down laminar flow, reduces cell temperature by over 35 °C and improves net electrical output by 30.9%, despite pump energy consumption. Porous media cooling, leveraging passive evaporation through gravel, decreases panel temperature by around 30 °C and achieves a net output gain of 26.3%. Mesh sensitivity and validation against experimental data support the accuracy of the model. These findings highlight the significant potential of water and porous material cooling strategies to enhance PV performance in hyper-arid environments. The study also demonstrates that porous media can deliver high thermal effectiveness with minimal energy input, making it a suitable low-cost option for off-grid applications. Future work will integrate long-term climate data, real diffuser geometries, and experimental validation to further refine these models. Full article

This study investigates the potential of low-cost, naturally available porous materials (PoMs), gravel, marble, flint, and sandstone, as thermal management for photovoltaic (PV) panels. Experiments were conducted in a controlled environment at a solar energy laboratory, where variables such as solar irradiance, ambient temperature, air velocity, and water flow were carefully regulated. A solar simulator delivering a constant irradiance of 1250 W/m² was used to replicate solar conditions throughout each 3 h trial. The test setup involved polycrystalline PV panels (30 W rated) fitted with cooling channels filled with PoMs of varying porosities (0.35–0.48), evaluated across water flow rates ranging from 1 to 4 L/min. Experimental results showed that PoM cooling significantly outperformed both water-only and passive cooling. Among all the materials tested, sandstone with a porosity of 0.35 and a flow rate of 2.0 L/min demonstrated the highest cooling performance, reducing the panel surface temperature by 58.08% (from 87.7 °C to 36.77 °C), enhancing electrical efficiency by 57.87% (from 4.13% to 6.52%), and increasing power output by 57.81% (from 12.42 W to 19.6 W) compared to the uncooled panel. The enhanced heat transfer (HT) was attributed to improved conductive and convective interactions facilitated by lower porosity and optimal fluid velocity. Furthermore, the cooling system improved I–V characteristics by stabilizing short-circuit current and enhancing open-circuit voltage. Comparative analysis revealed material-dependent efficacy—sandstone > flint > marble > gravel—attributed to thermal conductivity gradients (sandstone: 5 W/m·K vs. gravel: 1.19 W/m·K). The configuration with 0.35 porosity and a 2.0 L/min flow rate proved to be the most effective, offering an optimal balance between thermal performance and resource usage, with an 8–10% efficiency gain over standard water cooling. This study highlights 2.0 L/min as the ideal flow rate, as higher rates lead to increased water usage without significant cooling improvements. Additionally, lower porosity (0.35) enhances convective heat transfer, contributing to improved thermal performance while maintaining energy efficiency. Full article

The performance of photovoltaic (PV) cells is significantly influenced by their operating temperature. While conventional active cooling methods are limited by economic feasibility, passive cooling strategies often face challenges related to insufficient heat dissipation capacity. This study presents a bio-inspired evaporative heat sink, modeled on the transpiration and water transport mechanisms of plant leaves, which leverages porous media flow and heat transfer. The device uses capillary pressure, generated through the evaporation of the cooling medium under sunlight, to maintain continuous coolant flow, thereby achieving effective cooling. An experimental setup was developed to validate the device’s performance under a heat flux density of 1200 W/m², resulting in a maximum temperature reduction of 5 °C. This study also investigated the effects of porous medium thickness and porosity on thermal performance. The results showed that increasing the thickness of the porous medium reduces cooling efficiency due to reduced fluid flow. In contrast, the effect of porosity was temperature-dependent: at evaporation temperatures below 67 °C, a porosity of 0.4 provided better cooling, while at higher temperatures, a porosity of 0.6 was more effective. These findings confirm the feasibility of the proposed device and provide valuable insights into optimizing porous media properties to enhance the passive cooling of photovoltaic cells. Full article

The conversion efficiency of photovoltaic (PV) cells can be increased by reducing high temperatures with appropriate cooling. Passive cooling systems using air, water, ethylene glycol, and air/water+TiO₂ nano bi-fluid froth in the duct channel have been studied, but an overall assessment is essential for its possible application. In the present work, a numerical study is adopted to investigate the impact of the fluid-duct channel type on the electrical and thermal efficiency of the photovoltaic thermal (PVT) collector. Such investigation is achieved by means of a MATLAB R2022b code based on the Runge–Kutta (RK4) method. Four kinds of fluid duct channels are used to optimize the best fluid for improving the overall efficiency of the investigated PVT system. The numerical validation of the proposed model has been made by comparing the numerical and experimental results reported in the literature. The outcomes indicate that varying the duct channel nature affects mainly the electrical and thermal efficiency of the PVT collector. Our results validate that the nature of the fluid affects weakly the electrical efficiency, whereas the thermal efficiency is strongly affected. Accordingly, it is observed that PVT collectors based on nano bi-fluid air/water+TiO₂ give the best performance. In this context, an appreciable increase in the overall efficiency of 22% is observed when the water+TiO₂ fluid is substituted by air/ water+TiO₂ nano bi-fluid. Therefore, these motivating results make the PVT nano bi-fluid efficient and suitable for solar photovoltaic thermal applications since this system exhibits a daily overall efficiency of about 56.96%. The present work proves that controlling the design, cooling technique, and nature of the cooling fluid used is a crucial factor for improving the electrical, thermal, and overall efficiency of the PVT systems. Full article

The integration of photovoltaic (PV) and thermoelectric (TE) modules in PV-TE systems has shown potential for expanding the utilization of the solar spectrum, enhancing the total power output, and reducing the space that is required for PV power plants. This paper discusses the characteristics of a practical PV-TE system model. Typically, to boost the power output of the TE component, a significant temperature difference is induced across the thermoelectric generator (TEG) module using various heat removal methods. These cooling techniques not only enhance the TEG module’s efficiency but may also improve the performance of the PV component. In this study, we evaluate the efficiencies of PV-TE systems that are equipped with polycrystalline silicon solar cells and seven distinct TEGs under four different conditions. Initially, the PV-TE hybrid systems are tested without a cooling mechanism at an ambient temperature of 25 °C (Standard Test Conditions EN/IEC 61215). Subsequently, we examine the systems with a passive cooling approach, employing aluminum heat sinks to facilitate improved heat dissipation. Further tests involve an active cooling system using water and then nanofluid as coolants. The results from these assessments aim to establish a benchmark for enhancing the efficiency of future PV-TE systems. Full article

Energy and water poverty are two main challenges of the modern world. Most developing and underdeveloped countries need more efficient electricity-producing sources to overcome the problem of potable water evaporation. At the same time, the traditional way to produce energy/electricity is also responsible for polluting the environment and damaging the ecosystem. Notably, many techniques have been used around the globe, such as a photovoltaic (PV) cooling (active, passive, and combined) process to reduce the working temperature of the PV panels (up to 60 °C) to improve the system efficiency. For floating photovoltaic (FPV), water cooling is mainly responsible for reducing the panel temperature to enhance the production capacity of the PV panels, while the system efficiency can increase up to around 30%. At the same time, due to the water surface covering, the water loss due to evaporation is also minimized, and the water evaporation could be minimized by up to 60% depending on the total area covered by the water surfaces. Therefore, it could be the right choice for generating clean and green energy, with dual positive effects. The first is to improve the efficiency of the PV panels to harness more energy and minimize water evaporation. This review article focuses mainly on various PV and FPV cooling methods and the use and advantages of FPV plants, particularly covering efficiency augmentation and reduction of water evaporation due to the installation of PV systems on the water bodies. Full article

The efficiency of PV (photovoltaic) modules is highly dependent on the operating temperature. The objective of this work is to enhance the performance of PV by passive cooling using aluminum fins that have been nanocoated (like those on an automobile radiator). A rise in the cell temperature of the module PV leads to a decrease in its performance. As a result, an effective cooling mechanism is required. In this work, the performance of the PV module has been improved using natural convection, which was achieved by placing three similar PV modules next to each other in order to test them simultaneously. The first panel will be the base panel and will be used for comparison purposes. An automotive radiator (with aluminum fins) was firmly fixed onto the rear of the other two PV modules, and the fins of the third PV panel had titanium oxide (TiO₂) water-based nanofluid applied to them. The power produced by the PV modules, as well as their rear side temperatures, were recorded every 30 min over four months. A temperature reduction of 4.0 °C was attained when TiO₂ water-based nanofluid was sprayed onto the panel’s finned rear side. This was followed by the scenario where the rear side was only finned, with a temperature drop of 1.0 °C. As a result of the temperature reduction, the percentage of power produced by the coated-finned PV and the finned PV increased by 5.8 and 1.5 percent, respectively. This caused an increase in PV efficiency of 1.1 percent for coated-finned panels and 0.4 percent for finned PV. Full article

Limited reserves of fossil fuels, rising environmental concerns, and a remarkable increase in electricity demand have led to the necessity of harnessing solar energy on a large scale. For this purpose, there has been a noticeable stimulation into photovoltaic power plants (PVPPs) over the last three decades, but the land requirement for PVPPs is still a handicap in many countries since valuable lands are considered for other purposes such as agriculture and livestock. For effective conservation of valuable lands and water resources, PVPPs are preferred to be installed on various water bodies such as oceans, seas, lagoons, lakes, rivers, dams, canals, wastewater treatment plants, irrigation ponds, fish farms, wineries, reservoirs, etc. PV systems on water bodies are called floating PVPPs, and they have outstanding advantages compared with land-based PVPPs including better energy generation owing to passive cooling effects, higher system efficiency and reliability, and lower dirt and dust accumulation on PV modules thus lower operating costs. There are also some significant environmental features provided by floating PVs. Shading effects due to PV coverage reduce water losses arising from evaporation. Moreover, algae growth is limited because of mitigated solar radiation, which yields better water quality. This review presents more insight on floating PVPPs in terms of several aspects such as electricity generation, system efficiency, reliability and sustainability, experimental applications and facilities in operation, water and carbon saving as well as challenges. Full article

Our research aims to achieve dual-positive effects in the presented study by raising photovoltaic (PV) panels over the water surface. With this, target experiments were primarily conducted to evaluate the efficiency increments of the PV panel while reducing its operating temperature through passive convective cooling obtained by raising it over water. The following objective was to estimate the reduction in water evaporation due to the shading effect induced by the panel placed inside the same basin. The performance of two PV panels was analyzed, one used for tests, the other as a reference. The characteristic curves were determined under the local environmental conditions of Cagliari, Italy. The true temperature reduction and efficiency gain calculations of panel P1 due to water cooling was achieved via the measured temperatures and calculated efficiencies of panel P2 at environmental conditions. The water height inside the basin was constantly monitored and maintained at approximately 7.5 cm below panel P1, which covered about 17% of the total water surface area. The presence of water underneath P1 leads to its efficiency increment on average by 2.7% (absolute) and about 17.22% (relative). At the same time, temperature of panel P1 dropped by 2.7 °C on average. The comparative water evaporation study conducted with and without P1 inside the basin showed a 30% reduction in water evaporation. Full article

This paper presents the computational modeling of three cooling systems based on three different methods (passive, active, and hybrid), to improve the efficiency of PV panels when operating beyond the recommended temperature under standard test conditions. All simulations were implemented using the COMSOL Multiphysics software. In the passive method, through-holes were made in the solar panel, to allow the transfer of heat by convection due to the air flow. In the active method, water was used to cool the solar panel, spraying it on the front when the operating temperature reaches a threshold value. The analysis includes both fluid dynamics and heat transfer effects. In addition, a hybrid method that uses both passive and active cooling methods simultaneously was implemented. Finally, a mathematical model for the PV panel is presented, which allowed obtaining the changes in the output power from the reduction in the operating temperature. Results demonstrated improvements in the performance of the solar panel with the implementation of the three cooling systems, showing better performance in the active and hybrid methods compared to the passive method. Full article

A photovoltaic (PV) module’s electrical efficiency depends on the operating temperature of the cell. Electrical efficiency reduces with increasing PV module temperature which is one of the drawbacks of this technology. This is due to the negative temperature coefficient of a PV module which decreases its voltage significantly while the current increases slightly. This study combines both active and passive cooling mechanisms to improve the electrical output of a PV module. A heat sink made up of aluminum fins and an ultrasonic humidifier were used to cool the panel. The ultrasonic humidifier was used to generate a humid environment at the rear side of the PV module. The cooling process in the study was able to reduce the temperature of the panel averagely by 14.61 °C. This reduction led to a 6.8% improvement in the electrical efficiency of the module. The average power of 12.23 W was recorded for the cooled panel against 10.87 W for the referenced module. In terms of water consumption, a total of 1.5 L was approximately consumed during the whole experimental process due to evaporation. In effect, the proposed cooling approach was demonstrated as effective. Full article

High temperature and overheating of photovoltaic panels lead to efficiency losses and eventual degradation. For solar PV systems, this is a significant impediment for achieving economic viability. In this study, a novel Window-Integrated Concentrated Photovoltaic (WICPV) system is proposed for window integration. This offers high (50%) transparency and is fabricated and characterised indoors at an irradiance of 1000 Wm⁻². Its electrical performance is tested (a) without applied cooling (i.e., under natural ventilation) and (b) with a heat sink to accommodate passive cooling media. The results are compared to study the effects of reduction in operating temperature on system performances. The effectiveness of a sensible cooling medium (water) and two latent heat removal media, phase change materials (or PCMs, RT50 and RT28HC), is investigated. This paper reports the passive temperature regulation of this WICPV at ambient testing conditions. The results demonstrate an increase in electrical power output by (i) 17% (RT28HC), (ii) 19% (RT50), and (iii) 25 % (circulating water) compared with the naturally ventilated system. This shows that PCMs are considerably useful for thermal regulation of the WICPV. Any improvement in efficiencies will be beneficial for increasing electrical energy generation and reducing peak energy demands. Full article

Reducing the price of solar photovoltaic (PV) systems has been a constant challenge. Despite recent advances, solar PV systems are still more costly than conventional energy resources. For the first time, this study examines the effectiveness of three different structures/materials: (i) silvered glass plane mirror; (ii) convex spherical mirrors; and (iii) aluminum (Al) foil as reflector. Comparative analysis of four different cooling techniques, i.e., water sprinkling system, passive heat sink method, active air fan method, and closed loop method, for enhancement of output power was performed. A novel Bi reflector solar PV system (BRPVS) was suggested to control the working of the reflectors. The Al foil enhanced the power output compared to the others. In addition, the effect of using a reflector on the temperature of a solar PV system was studied. High operating temperatures resulted in a decrease in the maximum output power under the same solar radiation conditions. The combined enhancement of the output power by both Al foil BRPVS system and cooling system was almost 22.75–38.55%. An optimal control algorithm to use cooling and BRPVS in an efficient manner is described. Full article