Search Results (11)

A series of experiments has been conducted to investigate the tribological properties of a TiN film sliding against GCr15 steel balls in ambient air, low vacuum and high vacuum environments. Various friction loads and sliding velocities were also applied. The TiN film displays a steady-state friction stage after the running-in stage in all the above environments, while the durations of running-in stages are different. The steady-state friction coefficients of the TiN film were around 0.56 in ambient air and 0.3 in the high vacuum environment (1 × 10⁻⁵ mbar). In the low vacuum (1 × 10⁻² mbar) environment, a low friction coefficient (around 0.19) was attained for all the friction tests on TiN film, irrespective of the applied load and sliding velocity. In the meantime, it was noticed that the applied loads and the sliding velocities would change the duration of the running-in stage before reaching the low friction coefficient. It is revealed by the analysis of wear tracks that the metal oxides induced by the tribo-chemical effect at the friction interface play an important role in affecting the tribological behaviors of the TiN films in different environments. The Raman results show that the main component of the metal oxides is hematite (α-Fe₂O₃), and the amount of iron oxide is related to the friction environment. The composition and quantity of iron oxides produced by the interfacial tribo-chemical effect affect the tribological behavior. The results also show that the mechanical wear process at the friction interface displays a polishing effect, which would reduce the surface roughness. The mechanical wear performance varies under different loads and velocities. The tribological tests results indicate that the interfacial tribo-chemical effect and mechanical wear process should be considered together rather than individually to interpret the tribological behaviors of TiN films in different environments. Full article

A nanosecond laser is used to fabricate groove-patterned textures on the upper surface of Ti-6Al-4V alloys, and then molybdic sulfide solid lubricants are filled into the grooves. The treated titanium alloy is subjected to friction and wear tests. The tribological performances of Ti-6Al-4V alloys are evaluated, and the wearing mechanism is analyzed. The combination of solid lubricants and surface texturing can effectively reduce the frictional coefficient and reduce the adhesion of Ti-6Al-4V materials on the steel balls for friction. The main wearing mechanism is the adhesive wear of the Ti-6Al-4V alloy and the adhesion of Ti-6Al-4V alloy materials on the surface of the steel balls. During the friction process, solid lubricants are squeezed from the grooves and coated at the friction interface to form a solid lubrication layer. This is the important reason why the combination of surface texturing and solid lubricants can improve the friction properties of titanium alloys effectively. The combination of solid lubricants and laser surface texturing provides an effective alternative way to improve the tribological properties of titanium alloy materials. Full article

The tribological performance of both PI- and PEI-based nanocomposites, reinforced with chopped carbon fibers (CCF) and additionally loaded with halloysite nanotubes (HNTs) as well as carbon nanotubes (CNT), was investigated. Metal (GCr15 steel) counterparts were utilized in the point (“ball-on-disk”) and linear (“block-on-ring”) tribological contacts. In the point contact, the PEI/10CCF/1HNT nanocomposite was characterized by the maximum wear resistance and the absence of microabrasive damage of the steel counterpart (R_a = 0.02 µm). The effect of tribological layer formation through creep and mixing mechanisms was proposed to make it possible to protect (shield) the contacting surfaces. In the linear contact at the higher R_a counterpart roughness of 0.2 µm, the tribological layer was formed on both PI- and PEI-based nanocomposites. This was governed by the development of both creep and mixing processes under the cyclic action of the tangential load transmitted from the sliding counterpart and being localized on the wear track. Due to the combination of both higher manufacturability and lower cost, the PEI-based nanocomposite loaded with CCFs and HNTs is a promising inexpensive material for fabricating components of metal–polymer friction units. Full article

In the present paper, the effect of mechanical ball milling time on the fretting wear of GCr15 steel balls at different displacement amplitudes is investigated. TiC powder coating was fabricated on the surface of GCr15 steel balls using various process times, and the fretting wear tests were conducted on an AISI 52100 steel disk with the applied force of 80 N. Additionally, various displacement amplitudes (10 μm, 20 μm, and 60 μm) were selected. Specimen attributes and wear scars were characterized using an inverted metallographic microscope, a microhardness tester, an X-ray diffractometry analyzer, a white light interferometer, and a scanning electron microscope. The results showed that thick and continuous coatings could be obtained at the milling time of 18 h. The specimens processed for a longer milling time demonstrated better fretting wear resistance, which we attribute to higher microhardness of the surface layer. The coefficient of friction and wear volume of specimens at each different displacement amplitude significantly decreased with increasing milling time. As the displacement amplitude increased, the three fretting states were: partial slip coordinated by elastic deformation; partial slip state coordinated by plastic deformation; and gross slip condition. Our observations indicate that mechanical ball milling could be an efficient approach to improve the fretting wear resistance of GCr15 steel balls. Full article

In this paper, the corrosion resistance of four GCr15 steel samples has been investigated. Three samples were initially surface-treated by ultrasonic shot peening (USP), a dry ultrasonic strengthening grinding process (DUSGP), and a wet ultrasonic strengthening grinding process (WUSGP), respectively, while another one was only polished. Then, all the processed samples were subjected to salt spray corrosion. Sample properties, such as capacitance arc, self-corrosion potential (E_corr), self-corrosion current density (I_corr), corrosion morphology, and corrosion products were analyzed. Results show that the sample treated by WUSGP has the best corrosion resistance, which can be attributed to the high dislocation density, small grain size, needle-like and lath-like shape of martensite content formed in the treatment, which hinders Cl⁻ from eroding the matrix. The obtained corrosion pits and cracks in Sample WUSGP show a width of approximately 1.4 µm and 2.1 µm, respectively, degrading 78% and 75% compared to polishing. The possible corrosion mechanism of the samples has been discussed. The findings denote that the treatment fused ceramic balls, strengthened liquid, and corundum in USP could be an efficient method to improve the corrosion resistance of some mechanical parts. Full article

The work hardening behaviour of GCr15 bearing steel during rolling contact fatigue (RCF) is investigated. Ball-on-rod RCF tests and micro-indentation tests are performed to obtain various subsurface hardness profiles in rod specimens. It is found that orthogonal shear stress is responsible for work hardening under Hertzian contact and that the extent of hardness increase is positively associated with the stress level and number of cycles. A dislocation-based work hardening model is established by combining the Kocks–Mecking theory, the bearing steel plasticity equation and the Taylor relation. The proposed model is capable of predicting hardness changes with any given rolling contact stress state and number of cycles. The modelling results are compared against the experimental results, with good agreement obtained. This research also provides a methodology for studying the work hardening of different types of bearing steels undergoing RCF, from experiment to modelling. Full article

Titanium alloys are extensively used in the aerospace, chemical, and biomedical industries. However, it has always been a challenge in the manufacturing and machining of titanium alloys because they exhibit poor friction and wear characteristics, which results in serious problems and significantly restricts their further production and application. Therefore, in the present study, the wear contact between GCr15 steel and Ti6Al4V alloy is specifically studied by considering black phosphorus nanosheets (BP-NS) as water-based lubrication additives, which is expected to have a great potential application in manufacturing and machining titanium alloys. The influence of BP nanosheet size on the coefficient of friction (COF) and wear rate of Ti6Al4V alloy has been comprehensively studied, based on comparisons among adding large BP nanosheets (L-BP) (2–4 μm), medium BP nanosheets (M-BP) (300–500 nm), and black phosphorus quantum dots (BPQDs) (6–10 nm). Compared with ultrapure water, the COF and wear rate of Ti6Al4V alloy are reduced by 42.4% and 82.3%, respectively, when BPQDs are used as water-based lubrication additives. This paper also shows that a lower COF and wear rate is achieved with the addition of BPQDs than the other two BP nanosheet sizes. Derived from the friction tests and worn surface analysis of Ti6Al4V alloy, lubrication mechanisms of different-sized BP lubricants were proposed. The interlaminar shearing between BP-NS and the adsorbed films were the main mechanisms for L-BP and M-BP lubricants, while the adsorption, repair, and ball-bearing effects were mainly presented in the BPQD lubricants. The discoveries in this paper would be beneficial to developing novel lubricants for the manufacturing and machining of titanium alloys. Full article

MoAlB ceramic coatings were prepared on a 316 steel surface by atmospheric plasma spraying with different arc power levels. The phase composition, microstructure and wear resistance of coatings against GCr15 and Si₃N₄ counterparts were studied. The MoAlB ceramic decomposed and was oxidized to form MoB and Al₂O₃ during plasma spraying. With the increase of the arc power, MoAlB experienced more decomposition, but the coatings became denser. When the arc power increased from 30 to 36 kW, the wear rates of coatings against GCr15 and Si₃N₄ balls reduced by 91% and 78%, respectively. The characterization of wear tracks shows that when against GCr15 counterparts, the main wear mechanisms are abrasive and adhesive wear, and when against Si₃N₄ counterparts, fatigue and abrasive wear are dominant. The refinement of wear resistance by increasing arc power can be attributed to the improvement of density and adhesive strength among splats. Full article

During the bearing service, a series of microstructural evolutions will arise inside the material, such as the appearance of feature microstructures. The essential reason for the microstructural evolution is the cumulative effect of cyclic stress. The Hertz Contact formula is usually adopted to calculate the internal stress, and there is a correlation between the shape and distribution of the feature microstructure and the stress distribution. But it is insufficient to explain the relationship between the morphology of feature microstructures and the rolling direction, such as specific angles in butterfly and white etching bands. The rolling phenomenon will cause the asymmetry of stress distribution in the material, which is the source of the rolling friction coefficient. Moreover, slipping or microslip will produce additional stress components, which also cause the asymmetry of the stress field. However, there is no experimental or theoretical explanation for the relationship between the asymmetry of the stress field and the feature microstructure. According to the current theory, the appearance of feature microstructures is caused by stress with or without rolling. Therefore, it is of great significance to study the formation mechanism: whether feature microstructures will appear in the uniaxial cyclic compression stress field without rolling. In this paper, uniaxial cyclic compressive stress was loaded into a plate-ball system and a cylinder system. The characteristics of microstructural change of bearing steel (GCr15) were studied. It was found that the hardness of the material increased after the cyclic compressive load, and the inclusions interacted with the matrix material. In the local microregion a white etching area was found, although the scale is very small. No large-scale feature microstructures appeared. Other phenomena in the experiment are also described and analyzed. For example, the production of oil film in the contact area and the changing law of alternating load. Full article

In order to increase the surface hardness and wear-resistance property of sled track slippers, a Ni80Al20-MoS₂ composite coating was fabricated on the surface of a stainless steel 0Cr18Ni9Ti sled track slipper via atmospheric spray and hot dipping. The microstructure, composition and surface hardness of coatings under different spraying powers were characterized and measured. The wear-resistant properties of the slipper substrate and the coating were also checked. The results showed that the higher the spraying power was, the greater the smoothness, density and hardness was of the Ni80Al20 coating, while the thickness initially increased and then decreased. When the spraying power was 18 kW, the thickness was 342.5 μm, the surface hardness was 304.1 Hv_0.2, and the coating was composed of Ni, Al, Ni₃Al, NiAl and a little Al₂O₃. The friction coefficient of the slipper substrate against GCr15 balls at room temperature in air was 0.7, while the coated substrate with MoS₂ lubrication film was 0.3 and the volume wear rate declined by 1/5. The friction coefficient of the Ni80Al20 coating was 0.5 and the Ni80Al20-MoS₂ composite coating was 0.15, while the volume wear rate declined by 1/4 and 1/3. Full article

Surface texturing-plasma nitriding duplex treatment was conducted on AISI 316 stainless steel to improve its tribological performance. Tribological behaviors of ground 316 substrates, plasma-nitrided 316 (PN-316), surface-textured 316 (ST-316), and duplex-treated 316 (DT-316) in air and under grease lubrication were investigated using a pin-on-disc rotary tribometer against counterparts of high carbon chromium bearing steel GCr15 and silicon nitride Si₃N₄ balls. The variations in friction coefficient, mass loss, and worn trace morphology of the tested samples were systemically investigated and analyzed. The results showed that a textured surface was formed on 316 after electrochemical processing in a 15 wt % NaCl solution. Grooves and dimples were found on the textured surface. As plasma nitriding was conducted on a 316 substrate and ST-316, continuous and uniform nitriding layers were successfully fabricated on the surfaces of the 316 substrate and ST-316. Both of the obtained nitriding layers presented thickness values of more than 30 μm. The nitriding layers were composed of iron nitrides and chromium nitride. The 316 substrate and ST-316 received improved surface hardness after plasma nitriding. When the tribological tests were carried out under dry sliding and grease lubrication conditions, the tested samples showed different tribological behaviors. As expected, the DT-316 samples revealed the most promising tribological properties, reflected by the lowest mass loss and worn morphologies. The DT-316 received the slightest damage, and its excellent tribological performance was attributed to the following aspects: firstly, the nitriding layer had high surface hardness; secondly, the surface texture was able to capture wear debris, store up grease, and then provide continuous lubrication. Full article