Search Results (1,151)

Zinc oxide (ZnO) is a semiconductor with photocatalytic activity, although it presents limitations due to its band gap and the rapid recombination of the electron–hole pair; therefore, strategies such as doping have been explored. In this work, ZnO nanoparticles doped with 3% and 5% silver (Ag) were synthesized using a Cylindropuntia cholla root extract as a reducing and stabilizing agent. The structural, chemical, and optical properties of the synthesized nanoparticles were investigated using Fourier Transform Infrared Spectroscopy (FT-IR), X-ray Diffraction (XRD), Cathodoluminescence (CL), X-ray Photoelectron Spectroscopy (XPS), and Energy-Dispersive X-ray Spectroscopy (EDS). FT-IR shows that the nanoparticles have peaks between 400 cm⁻¹ and 406 cm⁻¹, attributed to the Zn–O bond. XRD characterization confirmed the formation of the wurtzite crystalline phase of ZnO, as well as the cubic phase of Ag. CL reveals two peaks: one attributed to the ultraviolet (UV) region and another in the visible region, which is associated with defects in the lattice. XPS and EDS confirm the presence of Zn, O, and Ag in the samples. The degradation of methylene blue was 90.9%, 96.4%, and 97.0% for ZnO, 3AgZnO, and 5AgZnO, respectively, demonstrating an improvement in dye degradation efficiency when doping ZnO nanoparticles with Ag. Full article

Poly(9,9-di-n-octylfluorene) (PFO) suffers from interchain aggregation, which degrades its blue spectral stability and charge transport. To address this, a series of rod-coil diblock copolymers (PFO-b-PMMAs) with varying poly(methyl methacrylate) (PMMA) chain lengths were synthesized via Steglich coupling. The non-conjugated PMMA blocks act as bulky steric spacers in the solid state, effectively suppressing detrimental PFO aggregation and enhancing pure blue emission stability. Furthermore, moderate PMMA blocks (PFO-b-PMMA1 and PFO-b-PMMA2) promote favorable β-phase formation and ordered crystalline packing. This microstructural optimization yields a maximum electron mobility of 1.98 × 10⁻⁶ cm²/(V·s) for PFO-b-PMMA2, markedly higher than the PFO-2 homopolymer (4.13 × 10⁻⁷ cm²/(V·s)). However, an overlong PMMA block (PFO-b-PMMA3) introduces excessive steric hindrance (T_g = 66 °C) that disrupts crystallization, acting as an insulating barrier that reduces mobility. Thus, precisely tuning the non-conjugated block length effectively maximizes both the blue spectral stability and electron transport capabilities of PFO-based materials. Full article

Elaeocarpus sylvestris (Lour.) Poir., an evergreen tree native to East and Southeast Asia, has gained increasing scientific attention owing to its broad pharmacological properties. Traditionally used in East Asian medicine to treat inflammation, fever, and infectious diseases, modern research has revealed diverse bioactivities, including potent antioxidant, anti-inflammatory, antiviral, anticancer, antidiabetic, and immunomodulatory effects. This therapeutic potential is primarily attributed to its rich phytochemical composition, particularly polyphenols such as geraniin, 1,2,3,4,6-penta-O-galloyl-β-D-glucose and quercetin. This review particularly focuses on the chemistry of E. sylvestris, summarizing structurally elucidated compounds, including hydrolysable tannins, flavonoids, and triterpenoids, along with recent insights into the structure–activity relationships that underpin these antiviral, antioxidant, and anticancer activities. Recent studies have demonstrated substantial antiviral efficacy of E. sylvestris extracts and isolated compounds against major human pathogens, including herpesviruses, influenza A virus, and SARS-CoV-2, supported by in silico, in vitro, in vivo, and early-phase clinical evaluations. Its cosmeceutical applications, including antioxidant, skin-whitening, and blue-light protective effects, further highlight its multifunctional potential. To our knowledge, this is the first comprehensive review summarizing the phytochemistry, pharmacological activities, therapeutic potential, and cosmeceutical applications of E. sylvestris. Despite these promising findings, challenges remain in elucidating precise molecular mechanisms, pharmacokinetics, and clinical validation. This review identifies current research gaps and future directions necessary to advance E. sylvestris as a scientifically validated natural therapeutic resource. Full article

This study aims to reduce the phase transition temperature (PTT) of W-doped vanadium dioxide (VO₂) multilayer thin films. We designed and fabricated two asymmetric multilayer thin film structures; namely, TiO₂/VO₂-5%W/ITO and ITO/VO₂-5%W/TiO₂. The W-doped VO₂-based Trilayer thin films were deposited using an electron beam evaporation combined with the ion-assisted deposition (IAD) technique. An experimental study was conducted on the temperature-dependent residual stress and optical properties of the two asymmetric VO₂-based three-layer structures. The VO₂-based thin films were characterized using UV–Vis–NIR spectrophotometry, Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and an improved Twyman–Green interferometer combined with fast Fourier transform (FFT) analysis for residual stress measurement. The trilayer structures incorporated a ~60 nm thick W-doped VO₂ middle layer, which plays a critical role in modulating thermochromic behavior and residual stress evolution. The results show that both trilayer thin films demonstrated excellent optical performance in transmission spectra. Raman spectral analysis revealed a blue shift in the characteristic W-doped VO₂ peaks, accompanied by a decrease in peak intensity as the temperature increased. Heating experiments on asymmetric W-doped VO₂ trilayer thin films revealed that the critical transition temperature of the ITO/VO₂-5%W/TiO₂/B270 trilayer film structure was significantly reduced to 45 °C. This demonstrates the effectiveness of our proposed multilayer film design in improving the PTT of W-doped VO₂ thin films. Analysis of the changes in residual stress of the trilayer thin films during heating experiments revealed that the residual stress shifted from compressive to tensile in the temperature range of 40 °C to 50 °C. The thermal expansion coefficient and biaxial modulus of the TiO₂/VO₂-5%W/ITO trilayer film structure were 5.37 × 10⁻⁶ °C⁻¹ and 295.7 GPa, respectively. In addition, the thermal expansion coefficient and biaxial modulus of the ITO/VO₂-5%W/TiO₂ trilayer film structure were 6.65 × 10⁻⁶ °C⁻¹ and 745.0 GPa. Full article

The current work aims to enhance the structural, optical, photocatalytic, and cytotoxic properties of CuO NPs at varied rGO concentrations of 5% and 10%. In the present work, a one-step hydrothermal method was successfully applied to prepare rGO/CuO NCs at different concentrations of RGO. The novelty of this work was to enhance the structural, optical, photocatalytic, and cytotoxic properties of CuO using the addition of rGO sheets. XRD, TEM, SEM-EDX, XPS, FTIR, UV-vis, PL, and DLS techniques were used to characterize the prepared samples. XRD data confirmed the formation of the monoclinic phase of CuO with a decrease in crystallite size, from 21.14 nm for CuO to 16.94 nm for the 10% rGO/CuO NCs nanocomposite. SEM and TEM images verified the uniform anchoring and excellent dispersion of CuO nanoparticles on the rGO sheets, and the EDX spectra showed the presence of Cu, O, and C elements in the obtained rGO/CuO NCs. DLS measurements showed that the hydrodynamic radius dropped from 69.98 ± 17.81 nm for CuO to 51.72 ± 10.48 nm for 10% rGO/CuO NCs. The zeta potential values remained negative for all samples, ranging from −20.50 ± 8.69 mV for CuO to −25.60 ± 9.08 mV for 10% rGO/CuO NCs, suggesting enhanced colloidal stability with rGO incorporation. Furthermore, FTIR and XPS analyses confirmed that Cu–O–C bonding formed between CuO and rGO. UV-Vis analysis revealed a redshift in the absorption edges as rGO content increased, reducing the band gap from 3.65 eV to 3.60 eV. Additionally, PL spectra showed a marked reduction in emission intensity due to a decrease in the recombination rate between electron (e⁻)–holes (h⁺) pairs. The CuO/(10%)rGO NCs showed the best photocatalytic performance with a 93.56% degradation of methylene blue (MB) after 120 min under UV irradiation, and followed pseudo-first-order kinetics with k = 0.0203 min⁻¹. Cytotoxicity studies on HT1080 cells showed a dose-dependent decrease in viability. 10% rGO/CuO NCs exhibited the highest cytotoxicity effect, resulting in 58% and 50% viability at 1.4 mg/mL, respectively. The presented results showed that the presence of rGO in CuO NPs played a role in enhancing the structural stability, charge mobility, and biological reactivity of Cu NPs. This study highlighted that the rGO/CuO NCs are a promising multi-functional material for environmental and biomedical applications. Full article

Stevia is a natural source of high-intensity sweeteners, collectively known as steviol glycosides (SG), which are approximately 300 times sweeter than sucrose and widely used as sugar substitutes. This study examines the impact of five different red-to-blue (R:B) light ratios on SG content and yield in hydroponic Stevia across four growth stages. Results indicate that the highest and lowest leaf dry weights were recorded in the R1B0 (R:B = 1:0) and R0B1 (R:B = 0:1) groups, at 2.88 and 1.98 g/plant, respectively, reflecting a 45.45% difference. The total SG content in dried leaves was highest in R0B1 (196.32 mg/g) and lowest in R1B0 (115.16 mg/g), with a 70.48% variation. The highest and lowest total SG yields (YSG) per square meter were observed in R0B1 (46.56 g/m²) and R50B37 (35.70 g/m²), differing by 30.42%. Stage-specific optimal YSG values were identified, with designated growth stages P1 (early vegetative growth phase), P2 (early leaf development phase), and P3 (late leaf development phase) favoring R4B1 and P4 (leaf senescence phase) favoring R0B1. These findings suggest an optimized lighting strategy for the four growth stages of hydroponic Stevia, sequentially applying R4B1, R4B1, R4B1 and R0B1 to enhance biomass accumulation and SG production at different developmental stages. Full article

After major disruptive events, particularly natural and human-made disasters, community leaders face the challenge of rebuilding societal infrastructure and managing the allocation of funds, which can affect the duration of recovery periods. Decision-makers must quickly determine how to allocate financial resources while minimizing population distress. Conventional methods of assessing damage and evaluating relief requirements fall short of meeting the urgent recovery needs after a disaster, potentially leading to negative effects on communities, such as involuntary relocation and neighborhood gentrification. The study evaluates current methods and technologies to propose a new approach that leverages low-cost consumer drones and modern image analysis techniques to support initial damage assessments and track recovery progress, thereby promoting the dynamic allocation of limited resources. Using low-cost drone imagery enables rapid, cost-effective data collection and dynamic analysis through iterative reviews during the disaster response and recovery phases that can adjust baseline disaster funding allocations. The study investigates the potential of temporary blue tarp roofs (“blue roofs”) as a metric for recovery progress during the 2020 tornado in Middle Tennessee and conducts an R-squared and error analysis. The goal of this research is to evaluate an affordable and efficient data analysis method (e.g., modern image analysis; artificial intelligence; low-cost drones) that can improve post-disaster resource allocation and inform decision-making for governmental and planning officials. Full article

This study presents a comparative analysis of the effect of methylene blue (MB) loading strategy on the physicochemical and colloidal properties of ethosomes prepared by the cold method. Two synthesis protocols differing in the phase of introduction of the cationic hydrophilic dye were investigated: a classical approach with MB loading into the aqueous phase and an alternative approach involving MB incorporation into the ethanolic lipid phase. It is shown that the loading strategy is a critical technological factor determining vesicle size, encapsulation efficiency, loading capacity, and electrokinetic properties of the systems. The alternative method results in the formation of smaller ethosomes (R_h ≈ 78 nm) compared to the classical protocol (R_h ≈ 96 nm), but is accompanied by a lower encapsulation efficiency (EE ≈ 36% versus 48%). The results indicate that a reduction in vesicle size does not necessarily lead to higher encapsulation of hydrophilic cationic MB and may be associated with a decrease in the total internal aqueous volume as well as an increased contribution of a weakly bound surface-associated dye fraction. Spectral analysis indicates the preservation of a predominantly monomeric form of MB within ethosomes, while differences in ζ-potential suggest distinct localization of the dye within the vesicular systems. Overall, the results highlight the importance of optimizing the loading protocol in the development of ethosomal drug delivery systems for photodynamic therapy and topical applications. Full article

The two-spotted spider mite, Tetranychus urticae Koch, is a major agricultural pest that causes economic losses in the cultivation of most crops worldwide. Pesticide resistance and the phase-out of many active pesticidal substances have accelerated research into alternative methods for pest management. The effects of light-emitting diodes (LEDs) on plants, as well as their potential use in pest management, have attracted the attention of researchers for the last 25 years. In this study, the repellent effects of UV-A, blue, and red LEDs on T. urticae were investigated using choice tests in laboratory conditions. The lethal effect of red LED light on adult individuals was determined by a no-choice test. Importantly, red LED caused 67.0 ± 4.5% (mean ± SE) mortality in adults in the no-choice test. Second, the UV-A LED clearly had a strong repellent effect on T. urticae in the choice tests. In the “UV-A vs. white LED” and “UV-A vs. darkness” choice tests, the egg-laying percentage in the UV-A part remained below 0.55%. Furthermore, UV-A also had a significant repellent effect on T. urticae larvae. In the choice tests, the larval ratio in the UV-A part was less than 5%. The results of laboratory experiments indicated that red and UV-A LEDs have significant lethal and repellent effects on T. urticae. Comprehensive investigations should be performed in greenhouses using different strategies to optimize how these potential effects can be used in pest management. Full article

In this study, CuCr50Ni_X (X = 0, 0.1, 0.5, and 0.9 wt.%) coatings were successfully fabricated on a pure copper substrate via infrared-blue hybrid laser cladding. The effects of Ni addition on the microstructure, mechanical and electrical properties, and arc erosion resistance under 24 V/30 A conditions were systematically investigated. The results demonstrate that Ni refines the Cr phase and promotes the formation of a (Cr, Ni) solid solution and nanoscale Cr₇Ni₃ precipitates during non-equilibrium solidification. The coating with 0.5 wt.% Ni exhibits optimal comprehensive performance. It achieves a high microhardness of 174.2 HV_0.5, representing a 149% increase compared to the copper substrate (72 HV_0.5). Simultaneously, it maintains a good electrical conductivity of 29.8% IACS. Arc erosion morphology transforms from localized deep pits (CuCr50) to uniform, shallow characteristics (CuCr50Ni_0.5), accompanied by reduced cathode mass loss. This enhanced performance is attributed to the refined and dispersed Cr distribution, which facilitates dynamic arc root movement, together with improved phase boundary stability conferred by the (Cr, Ni) solid solution and Cr₇Ni₃ precipitates. This work provides a novel strategy for developing high-performance, long-life electrical contact components through surface alloying design and laser additive manufacturing. Full article

Mastitis, a disease associated with milk production with multiple etiologies, causes significant economic losses among dairy farmers worldwide. This study aimed to detect mastitis using thermal images of the udder obtained during the milking phase from 500 Holstein dairy cows with the aid of an Artificial Neural Network (ANN). Mastitis levels were classified based on the California Mastitis Test (CMT) scores using somatic cell count (SCC) as the output variable. The dataset was divided into training (70%), validation (15%), and test (15%) subsets. RGB (Red, Green, Blue) thermal images were used to construct the input matrices. The model achieved correlation coefficients (R) of 0.91, 0.97, and 0.97 for the training, validation, and test datasets, respectively. The close agreement between validation and test performances indicates the absence of overfitting and demonstrates strong generalization capability of the proposed model. These findings suggest that artificial neural networks combined with thermal imaging can provide high-quality and reliable results for mastitis detection. Full article

Hybrid nanomaterials integrating magnetic and semiconductor phases offer promising multifunctional platforms for wastewater remediation; however, their stabilization and recovery remain challenging. In this study, Fe₃O₄ and ZnTiO₃/TiO₂ nanoparticles were incorporated into a rice husk ash-based geopolymer matrix to develop hybrid nanocomposites for synergistic adsorption–photodegradation of methylene blue (MB) and methyl orange (MO). The materials were synthesized via alkaline activation followed by nanoparticle incorporation, and characterized by XRD, XRF, FTIR, SEM, EDX, BET surface area analysis, and pHPZC determination. XRD confirmed the presence of nanocrystalline Fe₃O₄ and ZnTiO₃/TiO₂ phases while preserving the amorphous aluminosilicate framework. Modified powders exhibited higher specific surface areas (up to 198 m² g⁻¹) compared to the unmodified geopolymer. Adsorption followed the Langmuir isotherm and pseudo-second-order kinetics, with spontaneous and exothermic behavior. Under UV irradiation, the ZnTiO₃/TiO₂-modified composite achieved photodegradation efficiencies up to 94% for MB and 92% for MO, whereas the Fe₃O₄-modified material combined adsorption capacity with magnetic recoverability. These results demonstrate that nanoparticle incorporation enables multifunctional performance while maintaining structural integrity of the geopolymeric matrix. Full article

This study aims to evaluate the use of Tectona grandis sawdust (Teak) and activated carbons (ACs) prepared from Teak and modified with urea on the removal of methylene blue (MB) from the aqueous phase. Activation is performed with potassium hydroxide (KOH), and urea is added during chemical activation to increase nitrogen content in the AC matrix and improve textural properties. ACs are physiochemically characterized by elemental and Fourier Transform Infrared (FTIR) spectroscopy analysis, with the determination of the point of zero charge (pHpzc) and nitrogen adsorption at 77 K. The addition of urea allows for obtaining ACs with a higher pHpzc and carbon and nitrogen content, with improved textural properties when compared with the original AC. The addition of urea also promotes an increase in surface area and porous volume (1246 m² g⁻¹ and 0.64 cm³ g⁻¹). The modifications slightly affect the performance of the ACs in removing MB from water. While the original AC (AC_Teak_KOH_1_2) has a maximum MB adsorption capacity of 270.2 mg g⁻¹, the modified one (AC_Teak_KOH_urea (1_2_1)) has a maximum adsorption capacity of 281.7 mg g⁻¹. MB adsorption isotherms fit well with the Freundlich equation. Kinetic data fit well with the pseudo-second-order model, and the Weber–Morris representation shows that MB adsorption is described as a succession of two diffusion steps. The results make clear that it is possible to recover Teak waste through its transformation into ACs, presenting high application in the removal of dyes from water. Full article

Regional anaesthesia of the equine anogenital tract is limited to local infiltration, extradural, blind palpation and nerve stimulator-guided techniques which risk iatrogenic damage, recumbency and ataxia. This study aimed to describe and assess the feasibility of transcutaneous ultrasound-guided (USG) pudendal nerve staining in equine cadavers. An initial pilot phase used two fresh equine cadavers and one standing unsedated horse to image the intrapelvic anatomy using ultrasound. One fixed equine cadaver specimen was also dissected to identify the pudendal nerve and refine the dissection approach. The main study of six fresh equine cadavers used ultrasound to identify the landmarks of pelvic brim, pelvic urethra, rectum and semimembranosus musculature. Bilateral USG injection of 15 mL of methylene blue dye was performed, followed by anatomical dissection. The pudendal nerve was stained in 41.7% of injections, with an average staining length of 8.26 cm. Landmarks guiding dye injection were reliably imaged in all cadavers. Imaging of the pudendal nerve was not possible. Staining of the sciatic nerve did not occur. Transcutaneous USG pudendal nerve staining with methylene blue dye (15 mL) is possible in equine cadavers. However, this technique cannot be currently recommended. Further refinement in cadavers is necessary to improve the staining success rate. Full article

Carotenoproteins from marine sponges represent an underexplored class of pigment–protein complexes with distinctive structural and functional properties. Here, we report the isolation and biophysical characterization of a blue carotenoprotein from the sponge Tedania ignis, termed Ti-CP. The protein was purified and shown to consist of two closely related isoforms with molecular masses of approximately 27–29 kDa. Reverse-phase chromatography enabled separation of the apoprotein (ApoTi-CP) and its associated carotenoids, which were identified as oxygenated carotenoids consistent with astaxanthin and mytiloxanthin. Circular dichroism analysis revealed that both Ti-CP and ApoTi-CP are dominated by β-sheet secondary structure and display highly similar conformational profiles. In contrast, dynamic light scattering demonstrated that carotenoid binding is critical for protein stability, as the native form exhibited a compact and monodisperse organization, whereas ApoTi-CP showed pronounced aggregation. Isothermal titration calorimetry revealed that Ti-CP, but not ApoTi-CP, interacts with tetracycline, oxacillin, and streptomycin, indicating that pigment-mediated stabilization modulates ligand binding. Both Ti-CP and ApoTi-CP reduced bacterial viability and biofilm formation in a strain-dependent manner and enhanced antibiotic activity, including synergistic effects against resistant bacteria. Together, these results provide a comprehensive description of a previously uncharacterized sponge carotenoprotein and highlight the dual role of carotenoids in structural stabilization and antimicrobial modulation, reinforcing the biotechnological relevance of marine pigment–protein complexes. Full article