Search Results (11)

The thermocatalytic hydrogenation of CO₂ to methanol offers a promising route for reducing greenhouse gas emissions (GHG) and producing valuable chemicals and fuels. In this study, copper–zinc bimetallic catalysts supported on a zirconium-based MOF-808 framework were synthesized via a facile deposition–precipitation method and compared to a conventional Cu/ZnO/Al₂O₃ (CZA) catalyst. MOF-808 was selected due to its high surface area and porous structure, which enhance metal dispersion. Characterization through X-ray diffraction (XRD) and N₂ physisorption showed significant changes in surface area and pore structure after Cu-Zn incorporation and calcination. The 50-CuZn MOF-808 catalyst achieved the best catalytic performance at 260 °C and 40 bar, demonstrating a high STY of 193.32 gMeOH·Kgcat⁻¹ h⁻¹ and a turnover frequency (TOF) of 47.44 h⁻¹, surpassing traditional CZA catalysts. The strong Cu-Zn-Zr interactions within the MOF-808 framework played a crucial role in promoting CO₂ activation and methanol formation. This study underscores the potential of MOF-808-supported Cu-Zn catalysts as viable alternatives to traditional systems for CO₂ hydrogenation to methanol. Full article

Cardiac ablation (CA) is an interventional electrophysiological procedure used to disrupt arrhythmic substrates in the myocardium by inducing localized scarring. Current CA training relies on the master–apprentice model. In different fields of medicine including CA, virtual and physical simulators have proven to enhance, and even outperform, conventional training modalities while providing a risk-free learning environment. Despite the benefits, high costs and operational difficulties limit the widespread use of interventional simulators. Our previous research introduced a low-cost CA simulator using a 3D-printed biatrial cardiac model, successfully recording ten ablation lesions on the phantom myocardium. In this work, we present and evaluate an enhanced version: compared to the previous version, the cardiac phantom’s electrical behavior and ablation settings were optimized to produce consistent lesions, while 3D-printed components improved the haptic and radiographic properties of the simulator. Seven cardiologists compared the experimental simulator’s performance to the leading commercial system from Heartroid in a 24-question survey on a 5-point Likert scale. The four following areas of fidelity were considered: catheter entry, anatomical correctness, radiographic appearance, and mapping and ablation. The experimental simulator significantly outperformed the commercial system (p < 0.01), particularly in radiographic appearance (p < 0.01). The results show the potential for the experimental simulator in routine CA training. Full article

The land suitability in the Ratnagiri district (India) for mango crop has been assessed using a combination of multi-criteria decision making (MCDM) with GIS-based analytic hierarchy process (AHP), and sensitivity analysis. Five criteria are applied in this study to analyze land suitability affecting the mango production, viz., topography, climate, soil properties, soil erosion risk, and soil and water conservation practices, all affecting mango production. To prepare the land suitability maps for the mango plants, weights of criteria were identified through expert opinions and a pairwise comparison matrix. A weighted overlay tool available in ArcGIS software was applied in this study for the weighted overlay analysis. The most sensitive parameters were identified by developing and testing a total of 26 weighting schemes. After analyzing the sensitivity of parameters, the parameters related to soil and erosion such as terracing, contour trenching, stone bund, etc. were found as the most significant factors, before and after implementing the conservation measures. As a result, it was observed in this study that after conservation practices were implemented, the area in the highly suitable (19.4%) and moderately suitable (68.8%) classes was expected to rise, while the area in the marginally suitable (7%) class was expected to decrease. This research revealed that combining MCDM with GIS-based AHP as well as sensitivity analysis techniques increased the reliability of MCDM output for each criterion. Full article

The last decade witnessed the emergence of a new family of 2D transition metal carbides and nitrides named MXenes, which quickly gained momentum due to their exceptional electrical, mechanical, optical, and tunable functionalities. These outstanding properties also rendered them attractive materials for biomedical and biosensing applications, including drug delivery systems, antimicrobial applications, tissue engineering, sensor probes, auxiliary agents for photothermal therapy and hyperthermia applications, etc. The hydrophilic nature of MXenes with rich surface functional groups is advantageous for biomedical applications over hydrophobic nanoparticles that may require complicated surface modifications. As an emerging 2D material with numerous phases and endless possible combinations with other 2D materials, 1D materials, nanoparticles, macromolecules, polymers, etc., MXenes opened a vast terra incognita for diverse biomedical applications. Recently, MXene research picked up the pace and resulted in a flood of literature reports with significant advancements in the biomedical field. In this context, this review will discuss the recent advancements, design principles, and working mechanisms of some interesting MXene-based biomedical applications. It also includes major progress, as well as key challenges of various types of MXenes and functional MXenes in conjugation with drug molecules, metallic nanoparticles, polymeric substrates, and other macromolecules. Finally, the future possibilities and challenges of this magnificent material are discussed in detail. Full article

Protected cropping offers a way to bolster food production in the face of climate change and deliver healthy food sustainably with fewer resources. However, to make this way of farming economically viable, we need to consider the status of protected cropping in the context of available technologies and corresponding target horticultural crops. This review outlines existing opportunities and challenges that must be addressed by ongoing research and innovation in this exciting but complex field in Australia. Indoor farm facilities are broadly categorised into the following three levels of technological advancement: low-, medium- and high-tech with corresponding challenges that require innovative solutions. Furthermore, limitations on indoor plant growth and protected cropping systems (e.g., high energy costs) have restricted the use of indoor agriculture to relatively few, high value crops. Hence, we need to develop new crop cultivars suitable for indoor agriculture that may differ from those required for open field production. In addition, protected cropping requires high start-up costs, expensive skilled labour, high energy consumption, and significant pest and disease management and quality control. Overall, protected cropping offers promising solutions for food security, while reducing the carbon footprint of food production. However, for indoor cropping production to have a substantial positive impact on global food security and nutritional security, the economical production of diverse crops will be essential. Full article

Smart Glass Film (SGF) is a glasshouse covering material designed to permit 80% transmission of photosynthetically active light and block heat-generating solar energy. SGF can reduce crop water and nutrient consumption and improve glasshouse energy use efficiency yet can reduce crop yield. The effect of SGF on the postharvest shelf life of fruits remains unknown. Two capsicum varieties, Red (Gina) and Orange (O06614), were cultivated within a glasshouse covered in SGF to assess fruit quality and shelf life during the winter season. SGF reduced cuticle thickness in the Red cultivar (5%) and decreased ascorbic acid in both cultivars (9–14%) without altering the overall morphology of the mature fruits. The ratio of total soluble solids (TSSs) to titratable acidity (TA) was significantly higher in Red (29%) and Orange (89%) cultivars grown under SGF. The Red fruits had a thicker cuticle that reduced water loss and extended shelf life when compared to the Orange fruits, yet neither water loss nor firmness were impacted by SGF. Reducing the storage temperature to 2 °C and increasing relative humidity to 90% extended the shelf life in both cultivars without evidence of chilling injury. In summary, SGF had minimal impact on fruit development and postharvest traits and did not compromise the shelf life of mature fruits. SGF provides a promising technology to block heat-generating solar radiation energy without affecting fruit ripening and marketable quality of capsicum fruits grown during the winter season. Full article

Electric, hybrid, and fuel cell vehicles are the future of the automobile industry, and power source design is one of the most crucial steps in designing these vehicles. This paper aims to design and structurally simulate a custom accumulator—which powers an electric vehicle, for a lightweight, single-seater formula-style racecar. The work is dependent on the model-based design and CAD model approach. Mathematical modeling on SCILAB is used to model equations to get the characteristics of the accumulator, such as the energy, capacity, current, voltage, state of charge, and discharge rates. The output of this model gives the configuration of the battery pack as several cells in series and parallel to adequately power the tractive system. An accumulator container is designed to safeguard the cells from external impacts and vibrational loads, which otherwise can lead to safety hazards. Following this, the Finite Element Analysis (FEA) performed on the accumulator resulted in maximum peak deformation of 0.56 mm, ensuring the safety check against various external loads. Further, the finer stability of the battery pack was virtually validated after performing the vibrational analysis, resulting in a deformation of 3.5493 mm at a 1760.8 Hz frequency. Full article

Energy management in protected cropping is critical due to the high cost of energy use in high-tech greenhouse facilities. The main purpose of this research was to investigate the optimal strategy to reduce cooling energy consumption, by regulating the settings (opening/closing) of either vents or curtains during the day, at the protected cropping facility at Western Sydney University. We measured daily changes in air temperature and energy consumption under four treatments (open/closed combinations of vents and shade screens) and developed an optimal cooling strategy for energy management using multi-temperature acquisition points at different heights within a greenhouse compartment. The optimal treatment (vents open/curtains closed) reduced energy load at the rooftop, thereby maintaining a desirable plant canopy temperature profile, and reducing cooling energy. Daily energy consumption was lowest for vents open/curtains closed (70.5 kWh) and highest for vents closed/curtains open (121 kWh). It was also found that delaying the operation of opening and closing of vents and curtains until the plant canopy temperature reached 25 °C reduced cooling energy consumption and decreased heating energy consumption in the morning (e.g., 08:00 to 10:00). The estimated savings of 1.83 kWh per 1 °C cooling between the optimal (vents open/curtains closed) and least optimal (vents closed/curtains open) conditions had the potential for significant energy savings at 494 kWh per °C over a crop cycle of nine months in warm weather conditions. However, selection of the optimal cooling strategy utilising control of vents and curtains must also account for the impact from other greenhouse environmental factors, including light, humidity, and CO₂ concentration, which may be crop specific. Full article

Aflatoxin B₁ (AFB₁) is produced by the Aspergillus flavus and Aspergillus parasiticus group of fungi which is most hepatotoxic and hepatocarcinogenic and occurs as a contaminant in a variety of foods. AFB₁ is mutagenic, teratogenic, and causes immunosuppression in animals and is mostly found in peanuts, corn, and food grains. Therefore, novel methodologies of sensitive and expedient strategy are often required to detect mycotoxins at the lowest level. Herein, we report an electrochemical impedance sensor that selectively detects AFB₁ at the lowest level by utilizing polyaniline nanofibers (PANI) coated with gold (Au) nanoparticles composite based indium tin oxide (ITO) disk electrodes. The Au-PANI nanocomposites were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) spectroscopy, and electrochemical impedance spectroscopy (EIS). The composite electrode exhibited a 14-fold decrement in |Z|_{1 Hz} in comparison with the bare electrode. The Au-PANI acted as an effective sensing platform having high surface area, electrochemical conductivity, and biocompatibility which enabled greater loading deposits of capture antibodies. As a result, the presence of AFB₁ was screened with high sensitivity and stability by monitoring the changes in impedance magnitude (|Z|) in the presence of a standard iron probe which was target specific and proportional to logarithmic AFB₁ concentrations (C_AFB1). The sensor exhibits a linear range 0.1 to 100 ng/mL with a detection limit (3σ) of 0.05 ng/mL and possesses good reproducibility and high selectivity against another fungal mycotoxin, Ochratoxin A (OTA). With regard to the practicability, the proposed sensor was successfully applied to spiked corn samples and proved excellent potential for AFB₁ detection and development of point-of-care (POC) disease sensing applications. Full article

Formalin is a hazardous chemical, yet it is the choice of fixative for diagnostic pathology. Dental surgeons routinely use formalin for preservation of oral biopsy specimens. Literature search revealed that during regular biopsy procedures, unintentional injection with formalin has occurred, and such rare seven cases have been reported till date. In addition to the literature review, the present article describes first case of accidental local infiltration with formalin into the buccal mucosa during a biopsy procedure, its damaging effect on the oral tissues, subsequent judicious management of the patient and successful tissue reconstruction with collagen membrane. Full article

With the advent of nanotechnology, by looking further deep down into the molecular level, today, we are able to understand basic and applied sciences even better than ever before. Not only has nanoscience and nanotechnology allowed us to study the composing structures of materials in detail, it has also allowed us to fabricate and synthesize such nanostructures using top-down and bottom-up approaches. One such field, which has been significantly influenced by the dawn of nanotechnology is biomimetics. With powerful spectroscopic and microscopic tools presenting us with images like double nanostructured pillars on the lotus surface for superhydrophobicity, the conical protuberances of moth eye demonstrating anti-reflection properties and nanostructured spatulae of gecko feet for high adhesivity, we are now able to fabricate these structures in the lab with properties showing close resemblance to their natural counterparts. Here, we present a review of various nanostructures that exist in nature, their fabrication techniques and some of their promising future applications. We hope this review will provide the reader with a basic understanding of what biomimetics is and how nanotechnology has significantly influenced this field. Full article