Next Article in Journal
Non-Isothermal Crystallization Kinetic of Polyethylene/Carbon Nanotubes Nanocomposites Using an Isoconversional Method
Next Article in Special Issue
Machinability, Modelling and Statistical Analysis of In-Situ Al–Si–TiB2 Composites
Previous Article in Journal
Experimental and Numerical Determination of the Local Fiber Volume Content of Unidirectional Non-Crimp Fabrics with Forming Effects
Previous Article in Special Issue
Enhancing the Fracture Toughness Properties by Introducing Anchored Nano-Architectures at the Metal–FRP Composite Interface
Article Menu

Export Article

Open AccessArticle

Fatigue Performance of Wet and Dry Pulverized Wood Flour Reinforced PP Composites

1
Department of Mechanical Engineering, Yamaguchi University, 2-16-1 Tokiwadai, Ube, Yamaguchi 755-8611, Japan
2
Department of Applied Chemistry and Chemical Engineering, Islamic University, Kushtia-7003, Bangladesh
3
Cellulose Materials Group, National Institute of Advanced Industrial Science and Technology, 3-11-32 Kagamiyama, Higashihiroshima, Hiroshima 739-0046, Japan
4
Technology Development Center, TOCLAS Co., 1370 Nishiyama-cho, Nishi-ku, Hamamatsu, Shizuoka 432-8001, Japan
5
Okayama Prefectural Research Institute for Forest and Forest Products, 1884-2 Katsuyama, Maniwa, Okayama 717-0013, Japan
*
Author to whom correspondence should be addressed.
J. Compos. Sci. 2019, 3(1), 20; https://doi.org/10.3390/jcs3010020
Received: 30 November 2018 / Revised: 18 December 2018 / Accepted: 30 January 2019 / Published: 14 February 2019
  |  
PDF [4443 KB, uploaded 14 February 2019]
  |  

Abstract

In this paper, we exclusively studied the effects of dry and wet pulverization of different wood flours on the fatigue performance of polypropylene (PP)/wood flour (WF) composites. Wood flours obtained from cypress and Scots pine trees were pulverized in both dry and wet conditions at two different mill-plate gaps, 200 µm and 350 µm, and were used as reinforcement in PP matrices. Master batches of PP with different types of pulverized WF were compounded before processing in an extruder. The PP/WF composites of initial WF were also prepared for comparison. The prepared composites were analyzed by tensile and fatigue tests. It was found that the tensile properties of wood/polypropylene composites were affected by the pulverization of WF. Fatigue test results displayed that wet pulverization of short cypress flour had a negative effect on the fatigue life of PP/WF composites, while wet pulverization of long cypress flour and pine flour had a positive effect on the fatigue life of PP/WF composites. View Full-Text
Keywords: wood–plastic composite (WPC); fatigue behavior; wood flour; polypropylene wood–plastic composite (WPC); fatigue behavior; wood flour; polypropylene
Figures

Figure 1

This is an open access article distributed under the Creative Commons Attribution License which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited (CC BY 4.0).
SciFeed

Share & Cite This Article

MDPI and ACS Style

Haque, M. .-U.; Goda, K.; Ito, H.; Ogoe, S.; Okamoto, M.; Ema, T.; Kagawa, K.; Nogami, H. Fatigue Performance of Wet and Dry Pulverized Wood Flour Reinforced PP Composites. J. Compos. Sci. 2019, 3, 20.

Show more citation formats Show less citations formats

Note that from the first issue of 2016, MDPI journals use article numbers instead of page numbers. See further details here.

Article Metrics

Article Access Statistics

1

Comments

[Return to top]
J. Compos. Sci. EISSN 2504-477X Published by MDPI AG, Basel, Switzerland RSS E-Mail Table of Contents Alert
Back to Top