Next Article in Journal
Experimental Tests and Reliability Analysis of the Cracking Impact Resistance of UHPFRC
Previous Article in Journal
An Experimental Investigation on Optimizing Liquid Repellency of Fluorochemical Urethane Finish and Its Effect on the Physical Properties of Polyester/Cotton Blended Fabric
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Acetylation Treatment for the Batch Processing of Natural Fibers: Effects on Constituents, Tensile Properties and Surface Morphology of Selected Plant Stem Fibers

by
Isiaka Oluwole Oladele
1,*,
Omokafe Seun Michael
1,*,
Adeolu Adesoji Adediran
2,*,
Oluwayomi Peter Balogun
3 and
Folorunso Ojo Ajagbe
1
1
Departments of Metallurgical and Materials Engineering, Federal University of Technology, Akure, Ondo State PMB 704, Nigeria
2
Department of Mechanical Engineering, Landmark University, Omu-Aran, Kwara State PMB 1001, Nigeria
3
Prototype Engineering Materials Development Institute, Ilesa, Osun Sate PMB 5025, Nigeria
*
Authors to whom correspondence should be addressed.
Fibers 2020, 8(12), 73; https://doi.org/10.3390/fib8120073
Submission received: 18 September 2020 / Revised: 2 November 2020 / Accepted: 3 November 2020 / Published: 1 December 2020

Abstract

This work was on the comparative evaluation of the property effects obtainable when acetylation is applied to parts of selected agro fibers that are obtainable within common localities. The fibers were subjected to different concentrations of acetylation treatment at ambient temperature for 3 h. The physico-chemical, morphological, and tensile properties of the fibers were examined after the treatment. It was discovered from the results that the procedures variedly influenced the constituents of the fibers, their resulting tensile properties as well as their post-acetylation treatment surface morphology. The proportion of crystalline cellulose in the starting fibers greatly influenced their post treatment composition, behaviour and properties. The results show that plantain fibers had the highest aspect ratios, followed by banana fibers with values of about 1000 and 417, respectively. These fibers exhibited the least density and are thus potential plant fibers for composite development. Banana fiber had the least density of about 1.38 g/cm3 while that of DombeyaBuettneri fiber possessed the highest value of 1.5 g/cm3. There was significant enhancement in the hemicellulose content of Combretum Racemosum, while the lignin content of the plantain fibers was highly reduced. The treatment favoured the enhancement of the tensile properties in Combretum Racemosum fibers, which had enhanced tensile strength and strain at all compositions of the treatment. Optimum tensile strength and strain values of 155 MPa and 0.046, respectively, are achieved at 4% composition. Dombeya Buettneri fibers showed the highest ultimate tensile strength among the plant fibers in the untreated condition, which was gradually decreased as the concentration of the reagents was increased. Overall, 4% acetylation treatment is optimum for tensile properties’ enhancement for most of the natural fibers evaluated.
Keywords: environment impact; chemical treatment; cellulose; sustainable materials environment impact; chemical treatment; cellulose; sustainable materials
Graphical Abstract

Share and Cite

MDPI and ACS Style

Oladele, I.O.; Michael, O.S.; Adediran, A.A.; Balogun, O.P.; Ajagbe, F.O. Acetylation Treatment for the Batch Processing of Natural Fibers: Effects on Constituents, Tensile Properties and Surface Morphology of Selected Plant Stem Fibers. Fibers 2020, 8, 73. https://doi.org/10.3390/fib8120073

AMA Style

Oladele IO, Michael OS, Adediran AA, Balogun OP, Ajagbe FO. Acetylation Treatment for the Batch Processing of Natural Fibers: Effects on Constituents, Tensile Properties and Surface Morphology of Selected Plant Stem Fibers. Fibers. 2020; 8(12):73. https://doi.org/10.3390/fib8120073

Chicago/Turabian Style

Oladele, Isiaka Oluwole, Omokafe Seun Michael, Adeolu Adesoji Adediran, Oluwayomi Peter Balogun, and Folorunso Ojo Ajagbe. 2020. "Acetylation Treatment for the Batch Processing of Natural Fibers: Effects on Constituents, Tensile Properties and Surface Morphology of Selected Plant Stem Fibers" Fibers 8, no. 12: 73. https://doi.org/10.3390/fib8120073

APA Style

Oladele, I. O., Michael, O. S., Adediran, A. A., Balogun, O. P., & Ajagbe, F. O. (2020). Acetylation Treatment for the Batch Processing of Natural Fibers: Effects on Constituents, Tensile Properties and Surface Morphology of Selected Plant Stem Fibers. Fibers, 8(12), 73. https://doi.org/10.3390/fib8120073

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop