Next Article in Journal
Architecture and Viability of the Biofilms Formed by Nine Listeria Strains on Various Hydrophobic and Hydrophilic Materials
Next Article in Special Issue
Finite Element Steady-State Vibration Analysis Considering Frequency-Dependent Soil-Pile Interaction
Previous Article in Journal
Modeling and Solution of the Routing Problem in Vehicular Delay-Tolerant Networks: A Dual, Deep Learning Perspective
Previous Article in Special Issue
Calibration Factor for ASCE 41-17 Modeling Parameters for Stocky Rectangular RC Columns
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Seismic Behavior of Steel Plate-Concrete Shear Walls with Holes

1
Department of Civil Engineering, Tianjin University, Tianjin 300072, China
2
State Key Laboratory of Hydraulic Engineering Simulation and Safety, Tianjin 300072, China
3
Research Institute of Building and Construction CO.LTD.MCC Group, Beijing 100088, China
*
Author to whom correspondence should be addressed.
Appl. Sci. 2019, 9(23), 5255; https://doi.org/10.3390/app9235255
Submission received: 11 October 2019 / Revised: 21 November 2019 / Accepted: 27 November 2019 / Published: 3 December 2019

Abstract

:
Steel plate-concrete shear walls (SPSW) are used as the containment in nuclear power stations. However, the influence of holes and axial loading on the behavior of steel plate-concrete shear walls is neglected in most studies. Thus, it is necessary to understand the seismic behavior of SPSW members with holes in order to avoid the potential risks for nuclear power stations. In this study, a series of specimens were tested by low-cycle reciprocal loading. The specimens were designed with different holes to simulate real members in nuclear power stations. A hysteretic curve of specimens was obtained from a low-cycle reciprocal test to discuss the seismic behavior of steel plate-concrete shear walls (SPSW). Moreover, effects of axial compression ratio, hole size, thickness of the steel plate, and hole position on the hysteretic performance of SPSW were analyzed. The horizontal ultimate bearing capacity of SPSW specimens was estimated using the norms of the Architecture Institute of Japan and the calculation method of Ono reduction rate. Results provide theoretical references for the design and application of SPSW with holes.

1. Introduction

Steel plate-concrete shear walls (SPSW) serve as the containment of AP1000 and CAP1400 nuclear power stations and of the stress components of the internal plants in nuclear power stations. Structures with SPSW have advantages of modular construction and strong seismic and impact resistance. In the 1960s, Japan began to apply the steel stiffening concrete seismic structural structure. A series of studies on shear capacity and the stiffness and ductility of SPSW structures have been conducted in many countries, such as the US and Japan [1]. Other relevant research is based on low-cycle reciprocal tests. Lubell et al. [2] conducted an experimental testing on two single and one four-story steel shear wall specimens under cyclic quasi-static loading. Hjjar et al. [3] performed a low-cycle reciprocal test on a 1:2 scale model of SPSW structure and found its high bearing capacity, energy-consumption mechanism, and good ductility. The test results show that the superposition principle is basically true [4]. Berman et al. [5] conducted an experiment on the light-gauge steel plate shear walls and braced frames to study the hysteretic behavior. They revealed that the energy dissipated per cycle and the cumulative energy dissipation are similar for the two structures. Later, Gan, Zhao, and Wang et al. [6,7,8] studied the seismic behavior of the steel plate-reinforced concrete shear wall by using the quasi-static test. Li and li [9] investigated the out-of-plane seismic behavior of steel plate and concrete infill composite shear walls (SCW). They found that SCW has a better ultimate capacity and lateral stiffness. Huang et al. [10] proposed an innovative concrete-filled double-skin steel plate SCW and investigated its seismic behavior. By conducting a quasi-static cyclic test, the wall is confirmed to have good seismic performance.
In recent years, various scholars have simulated the hysteretic curve and stiffness reduction rate of SPSW through finite element simulation. Rafiei et al. [11] presented and verified the finite element model to simulate the behavior of a novel SCW consisting of the two skins of profiled steel sheeting and an infill of concrete under in-plane loadings. Hu et al. [12] analyzed the moment-curvature behavior of concrete-filled steel plate SCW using refined material constitutive models. Peter et al. [13] presented the development and benchmarking of a detailed 3D nonlinear inelastic finite element model to predict the lateral load-deformation response and behavior of the 1/6th scale test structure. Nguyen et al. [14] presented a numerical study of steel-plate concrete composite walls by using the general-purpose finite element program ABAQUS. The influence of key design variables, including the reinforcement ratio, connector type, and faceplate slenderness ratio, were likewise studied. Wang et al. [15] investigated the hysteretic performance of the SPSW wall by using Open Sees software. Moreover, parameters such as the steel plate ratio, axial compressive load ratio, concrete strength, and web reinforcement ratio were analyzed. Yamatani [16] performed a low-cycle reciprocal test of SPSW with holes at the lower position under the shear-span ratio of 0.7, a distance–thickness ratio of 100, and opening area ratio of 0.3. Other scholars proposed the concept of reduction coefficient to evaluate the bearing capacity of an SPSW wall. Satou Kouichiet al. [17] conducted a numerical simulation of an SPSW structure and found that a numerical simulation is applicable for the calculation and analysis of the performance of shear walls with holes. Ishida Masatoshi [18] analyzed the seismic behavior of an SPSW structure by using theories and finite element simulation. Fujita Tomohiro and Oosuka et al. [19,20] performed anti-shear tests on SPSW structures with holes. Adding sleeves and using increased thickness surface steel plates on the shear wall were determined to be effective reinforcement methods. Some scholars also used the XFEM (the eXtended Finite Element), XIGA (the eXtended IsoGeometric Analysis) and Jaya algorithm to predict the occurrence of cracks and other defects in walls and slab [21,22,23].
So far, steel plate-concrete shear walls are studied widely. However, the influence of holes and axial loading on the behavior of steel plate-concrete shear walls are neglected in most studies. Thus, the seismic behavior of steel plate-concrete shear walls is completely different when the influences are considered. In the study, a series of low-cycle reciprocal loading tests are conducted on an SPSW structure with holes, thus obtaining the ultimate bearing capacity and failure mode of the structure. The influences of holes and reinforcing measures and axial loads of components on the seismic behavior of an SPSW structure are analyzed, thus determining the difference between theoretical and test values. The seismic behavior and stress mechanism of SPSW specimens are discussed theoretically.

2. Experiment

2.1. Experimental Apparatus

A low-cycle reciprocal test of an SPSW structure with different hole sizes was conducted in the Beijing Key Laboratory of Engineering Anti-earthquake and Structural Diagnosis of the Beijing University of Technology. The test applied a horizontal servo actuator (maximum range = 2000 kN), which was fixed on the concrete counterforce wall. Test devices included a counterforce wall, counterforce frame, loading beam, bottom beam, and displacement meter. The bottom beam was strongly connected to the ground through a fixing device, and a steel ingot was used on the loading beam. On the one hand, this design prevents concrete crushing caused by excessive force. On the other hand, the vertical load is ensured to be a uniform load. In the test, the low-cycle reciprocal loading test device is composed of horizontal and vertical jacks. In this device, the jack on the transverse counterforce frame applies the vertical loads. During the whole test, these vertical loads are kept as stable as possible through the manual control of the oil pump. The horizontal jack applies the horizontal loads. One end of the jack is connected to the loading beam of the specimens, and the other end is fixed on the counterforce wall (Figure 1).

2.2. Design of Specimens and Instrumentation

To accurately reflect shielding plants and internal SPSW structures in a nuclear power station, specimens in this study were designed with reference to Japan’s Technical Regulations on Earthquake-resistant Design of Steel Plate Concrete Structure (JEAC4618-2009) [24] and design documents of AP1000 demonstration projects. According to Technical Regulations on Earthquake-resistant Design of Steel Plate Concrete Structure, the ratio between the thickness of SPSW for nuclear safety and thickness of the surface steel plate should be controlled within 30:200. On this basis, thicknesses of the shear wall and surface steel plate were set. Considering the actual welding ability in the laboratory, the thickness of the surface steel plate in the test specimens was determined to be 2.5 mm.
In this study, low-cycle reciprocal tests of nine SPSW specimens were conducted. Dimensions of SPSW specimens were 800 mm (height) × 800 mm (width) × 125 mm (thickness). SPSW specimens were divided into three types: (1) without holes, (2) with small holes, and (3) with large holes. Considering the loading capacity of the laboratory, the SPSW specimens without holes and with small holes were flat (Figure 2), whereas the SPSW specimens with large holes were I-shaped (Figure 3). The stiffening plates were spread around the hole, with a width is 90 mm, and the length determined by the perimeter of the hole. The hole size, thickness of the stiffening plate, hole position, and axial pressure ratio are listed in Table 1. In the SPSW specimens, the steel plate was made of Q235B, and the grade of the concrete strength was C35. Material properties are shown in Table 2 and Table 3. Fine aggregates with a diameter smaller than 10 mm were used.
In the test, five displacement sensors were set (Figure 1), three of which were set vertically on the wall. The first displacement sensor on the side of the loading beam of the shear wall tested the top wall displacement under reciprocal loads. The displacement sensor in the center of the shear wall examined the bottom slippage during the loading process. The displacement sensor on the side of the bottom beam tested the overall slippage of specimens to assure test accuracy. In addition, two dial indicators were installed at diagonal positions of the wall to test for outward deflection.

2.3. Loading Mode

The loading process is composed of pre-loading and formal loading. First, the vertical jack applied the vertical loads, and then 20kN force was pre-loaded by a horizontal actuator. Second, loads were removed to ensure contact of the loading device with the specimens. The loading protocol refer to construction standards of the China Construction Industry JGJ/T 101-2015 [25].
In the formal loading, the vertical jack also applied the vertical loads on the specimens. Before full loading, the vertical loads were applied 2–3 times according to the design value of 40–60% to eliminate the influences of the internal non-uniformity of shear wall specimens. When the vertical load was applied to the designated value and stabilized, a horizontal actuator was used to apply the horizontal low-cycle reciprocal loads to the specimens. Load control was applied in the early stage of the test. Loads in the first, second, third, and fourth cycles were 50, 100, 200, and 400 kN, respectively. Later, loads were increased by 100 kN every cycle until specimens fail. The loading system is illustrated in Figure 4. Specimens were considered a failure upon attaining one of the following cases:
(1)
The bearing capacity of specimens decreased to lower than 85%.
(2)
Serious failure occurred in specimens, such as heaving of steel plates or crushing of concrete, thereby resulting in a difficult loading.

3. Experimental Analysis

3.1. Failure Mode

Specimen SCW-1 is an SPSW without holes. The loading process of SCW-1 was relatively stable. When the cyclic loading approaches 700 kN, the concrete begins to crush, and the steel plate develops slight deformation. With the continuous increase in loads, the crushing region in the concrete and deformation of steel materials likewise continued. Heaves develop on the steel plate at the root side of the shear wall until the load reaches 1100 kN. When the cyclic loads increase to 1240 kN, heaves at the root side of the steel plate of the shear wall and surface steel plate intensify, accompanied with the crushing of concrete at root positions. Due to the processing deviation of specimens and influences of initial defects, deformations of steel plates at the two root sides of the shear wall are inconsistent but are symmetric to an extent.
In the tests of flat specimens with small holes, the horizontal loads are small in the initial loading stage, and specimens are still elastic. A linear relationship is observed between the horizontal load and vertex displacement of specimens. In the late stage, internal concrete begins to crack as horizontal loads increase. The side and surface plates yield successively. As lateral displacement increases, the steel plate begins to bend or crack. The weld joints of several specimens are pulled open, and internal concretes are crushed, resulting in failure (Figure 5). The main failure develops at the wall bottom and is evaluated as brittle failure. Several specimens develop slippage due to the lower stiffness of the bottom beams.
Figure 6 shows the failure mode of I-shaped SPSW specimens with large holes. Bending shear failure is the dominant failure mode. In the test of SCW-8, the internal concrete in SPSW begins to crack at approximately 500 kN. Furthermore, the steel plate at the holes begins to yield and pull open at approximately 800 kN. The surface steel plate yields at 1100 kN. Subsequently, the surface plate cracks and bends, accompanied with wrinkles. The internal concrete of the steel plate is crushed after losing constraints. Moreover, the steel plate at the wing wall side buckles, and the wall develops serious deformation. The bearing capacity of SPSW specimens continue to decrease, and the loading test is terminated. According to the results, SCW-8 with holes at the center and SCW-9 with holes biased to the axis have no significant differences in terms of bearing capacity and failure mode.

3.2. Effects of Axial Compression Ratio on the Hysteretic Performance of SPSW Specimens

The axial compression ratio is an important factor that influences the hysteretic performance of SPSW specimens. In this section, axial compression ratios in the low-cycle reciprocal tests of three SPSW specimens with holes (SCW-3, SCW-4, and SCW-5) are set at 0.15, 0.3, and 0.5, respectively. The ultimate loads and displacements of specimens are shown in Table 4. Figure 7 illustrates the hysteretic curves of different SPSW specimens, whereas Figure 8 shows the skeleton curves.
In the loading process of the three specimens, steel plates develop low sounds, and internal concretes begin to crack at 350 kN when the axial compression ratio is 0.5. When the axial compression ratios are 0.15 and 0.3, steel plates develop low sounds at 500 kN and 150 kN, respectively. In summary, the concrete begins to crack early under large axial compression ratios. With the continuous increase of loads, SCW-3 and SCW-4 show a reduction stage of loads and good ductility. When loads increased to 1217 kN, the root plate of SCW-4 bent, and the test was terminated. SCW-4 thus shows poor ductility, as verified from the skeleton curve. Table 4 shows that the ultimate bearing capacity of components is positively related with axial compression ratio, but deformation resistance and ductility are negatively correlated. Therefore, attention should be paid to the sudden failure of structures under high axial compression ratio.

3.3. Effects of Hole Area on the Hysteretic Performance of SPSW Specimens

Influences of hole size on lateral bearing capacity, deformation resistance, and energy consumption of SPSW specimens with different hole sizes are determined through a low-cycle reciprocal test. Ultimate strengths and displacements of SPSW specimens with different hole sizes are presented in Table 5. Figure 9 and Figure 10 respectively display the hysteretic and skeleton curves of SPSW specimens with different hole sizes.
Table 5 shows that as hole area increases, the ultimate displacement of specimens gradually increases, but the ultimate loads of specimens decrease slightly. Hysteretic curves of SCW-1, SCW-3, and SCW-7 have similar shapes. They are full but have clear twist contraction effects. Compared with the first three specimens, SCW-8 has a fuller hysteretic curve, indicating better seismic behavior.

3.4. Effects of the Thickness of the Stiffening Plate on the Seismic Behavior of SPSW Specimens

SCW-1, SCW-4, and SCW-6 have the same appearance size.SCW-1has no hole, SCW-4 and SCW-6 have the same geometric size, hole position, and hole size but are equipped with 2.5 mm and 3.5 mm stiffening plates, respectively. Table 6 shows that compared with the uncut SCW-1, the strength and stiffness of the open specimens are decreased. Compared with the ultimate strength of SCW-4, the ultimate strength of SCW-6 increased by 4% in the positive direction and 10% in the negative direction. The hysteretic curves of SCW-4 and SCW-6 are shown in Figure 11, and the skeleton curves of specimens are shown in Figure 12. The hysteretic curve of SCW-6 is S-shaped, which is attributed to slippage caused by anchoring failure. Similarly, the SCW-6 skeleton curve displays that its initial stiffness is low due to the large specimen displacement.

3.5. Effects of Hole Position on the Seismic Behavior of SPSW Specimens

Figure 13 and Figure 14 illustrate the hysteretic and skeleton curves of specimens with large holes at different positions as determined through low-cycle reciprocal tests, respectively. The ultimate strengths and displacements of specimens are presented in Table 7.
Table 7 shows that the ultimate displacement of the specimen with a hole in the center is higher than that of the specimen with an eccentric hole. Comparing the two specimens, the hysteretic curve of the specimen with a hole in the center is fuller, and its energy-dissipation capacity is larger. Hence, placing the hole in the center of SPSW structures is suggested for practical engineering.

4. Theoretical Calculation

In order to estimate the ultimate bearing capacity and lateral stiffness resistance of SPSW specimens with holes, two calculation methods are discussed. The first method is the reduction rate calculation method of the Architecture Institute of Japan (AIJ) [26], and the second method is the Ono method [27]. A comparison between the experimental results and the theoretical results are discussed.

4.1. ReductionRate Calculation Method of AIJ

The calculation methods of the reduction rates of horizontal bearing capacity ( r u ) and stiffness ( r c ) of shear wall components with holes are regulated in the structural design codes of AIJ. These two calculation formulas are as follows:
r u = 1 - η ,
r c = 1 1.25 h 0 l 0 h l ,
where h 0 and l 0 are the height and width of the hole, h is the floor height, l is the center distance of frame columns, η is the hole area ratio with value η = max { h 0 l 0 h l } , and where h 0 l 0 h l 0.4 . In AIJ codes, the application of these formulas is regulated; they are applicable to situations when the hole area is smaller than 0.4 but not for situations when the hole area is larger than 0.4. In these formulas, the shape and position of holes are not considered when calculating bearing capacity and stiffness. That is, the calculated results of bearing capacity and stiffness are the same for specimens with the same hole size.

4.2. Ono Reduction Rate Calculation

Ono Masasyuki, a Japanese scholar, proposed the calculation method of Ono reduction rate through a series of experiments wherein the influences of hole positions are considered [27] (Figure 15).
r u = A e i / h l ,
when 0.1 γ 0.53 ,
r e = ( 0.025 0.0303 γ ) × α β + ( 0.6 0.55 γ ) / ( 1.55 γ 2 ) k ,
when 0.53 γ 1.00 ,
r e = ( 5.24 717.24 γ ) × α β + ( 0.6 0.55 γ ) / ( 1.55 γ 2 ) k ,
where A e i is the area of shadow part, h is the floor height, and l is the center distance of frame columns. α β = 2 b D / t l ; where b D is the sectional area of columns, t is the wall thickness, and l is the net span. γ = 2 l w / l ; and where l w is the length of the wall after the hole is removed. κ = h 0 / h , where h 0 is the height of the hole and h is the net height of the wall.
In this study, the horizontal ultimate bearing capacity of SPSW members with holes can be obtained by multiplying the reduction rate by that of the corresponding members without holes. The lateral stiffness of SPSW members with holes can be obtained with the same method. Change of the concrete compression zone is considered in the method of Ono reduction rates. The reduction rates are different in different directions for the specimen with biased holes.
Table 8 displays the comparison between the test results of horizontal ultimate loads and the calculated results based on strength reduction rate. Table 9 compares the test results of lateral stiffness and calculated results based on the stiffness reduction rate. This test has no effective lateral stiffness of I-shaped SPSW structures without holes, and only the comparisons between the calculated and test results of SCW-4 and SCW-6 are presented. According to the average ratio, the calculated value of the Ono formula is closer to the experimental value than that of the code formula.
Table 9 shows that the calculated results of AIJ codes are relatively safe. Moreover, the difference of bearing capacity along different loading directions under eccentric holes is neglected, thus resulting in the low accuracy. The Ono calculation formula considers the influences of loading direction and reflects the effects of hole position on horizontal bearing capacity along different loading directions. The calculation accuracy of the Ono calculation formula is thus higher than that of AIJ codes with respect to specimens with small holes (SCW-4 and SCW-6) and with large holes (SCW-8 and SCW-9). With respect to stiffness, the bottom slippage of the wall can influence the test results to a certain extent, resulting in the difference in stiffness along the two loading directions. Therefore, the calculation method may differ. In summary, the calculation formulas of AIJ codes and Ono are feasible in determining the influences of holes on the horizontal bearing capacity of SPSW structures. Compared with the calculation results of AIJ codes, those of the Ono formula are closer to the actual test results, indicating its high calculation accuracy. Due to the bottom slippage of walls, the rigidity in the negative direction is lower than the calculated values. In the positive direction, the calculated values are lower than the test results, which is due to the fact that the AIJ code and Ono formula are used for structure design and the result are relatively safer.

5. Conclusions

Steel plate-concrete shear walls are studied widely. However, the influence of holes and axial loading on the behavior of steel plate-concrete shear walls are neglected in most studies. Thus, the seismic behavior of steel plate-concrete shear walls is completely different when the influences are considered. Thus, a series of low-cycle reciprocal loading tests were conducted on SPSW specimens with holes in this study. The failure modes and hysteretic curves of SPSW structures under different working conditions were also studied. On the basis of failure modes and hysteretic curves, the seismic behavior of SPSW structures was discussed. Influences of axial compression ratio, hole size, hole position, and the thickness of stiffening plate on the seismic behavior of SPSW structures were considered in the tests. The ultimate bearing capacity of SPSW structures with holes was estimated by AIJ codes and Ono reduction rate calculation methods. The major conclusions are indicated as follows:
(1)
SPSW structures without holes mainly develop failures at the roots of shear walls, accompanied with the concrete and bending failures of steel plates. SPSW structures with small holes also develop failures at the roots, but several steel plates crack along the corners of the holes. The failure mode is brittle to a certain extent. SPSW structures with large holes develop significant deformation and better ductility than SPSW structures with small holes but low ultimate loads.
(2)
Concrete cracks early under high axial compression ratio. The ultimate strength of SPSW structures increases, but the deformation capacity and ductility decrease to a certain extent. Deformation capacity is enhanced, but the ultimate bearing capacity decreases as hole size increases. With an increase in the thickness of stiffening plates, the ultimate bearing capacity of SPSW specimens increases. Eccentric holes decrease the earthquake-resistant energy-dissipation capacity of SPSW structures, and such a reduction is disadvantageous to seismic design. Therefore, eccentric holes on SPSW structures should be avoided.
(3)
The calculated results of AIJ codes are safe, but those of the Ono formula have high accuracy because it considers the influences of loading directions. In summary, both calculation formulas are feasible to calculate the ultimate shear capacity of SPSW structures with holes.

Author Contributions

Z.C. and J.W. carried out the experimental research and the academic paper writing. H.L. provided assistance during the experimental research.

Funding

This research received no external funding.

Conflicts of Interest

There is no conflict of interest.

References

  1. Akiyama, H.; Sekimoto, H.; Tanaka, M.; Inoue, K.; Fukihara, M.; Okuda, Y. 1/10th scale model test of inner concrete structure composed of concrete filled steel bearing wall. In Proceedings of the 10th SMi RT Conference H73, SMiRT 10, Anaheim, CA, USA, 22–27 August 1989; pp. 73–78. [Google Scholar]
  2. Lubell, A.S.; Prion, H.G.; Ventura, C.E.; Rezai, M. Unstiffened steel plate shear wall performance under cyclic loading. J. Struct. Eng. 2000, 124, 453–460. [Google Scholar] [CrossRef]
  3. USNRC Regulatory Guide 1.142 Revision 2. In Safety-Related Concrete Structures for Nuclear Power Plants (Other than Reactor Vessels and Containments); NRC: Washington, DC, USA, 2001.
  4. Japanese Association of Architectural Technicians. 100 Typical Examples of Japanese Structural Technology; Architecture and Building Press: Beijing, China, 2005. [Google Scholar]
  5. Berman, J.W.; Celik, O.C.; Bruneau, M. Comparing hysteretic behavior of light-gauge steel plate shear walls and braced frames. Eng. Struct. 2005, 27, 475–485. [Google Scholar] [CrossRef]
  6. Gan, C.; Lu, X.; Wang, W. Experimental study on the steel plate reinforced concrete shear walls. In Proceedings of the International Conference on Advances in Experimental Structural Engineering, Tongji University, Shanghai, China, 4–6 December 2007; pp. 176–188. [Google Scholar]
  7. Zhao, W.Y.; Guo, Q.Q.; Huang, Z.Y.; Tan, L.; Chen, J.; Ye, Y. Hysteretic model for steel–concrete composite shear walls subjected to in-plane cyclic loading. Eng. Struct. 2016, 106, 461–470. [Google Scholar] [CrossRef]
  8. Wang, W.; Wang, Y.; Lu, Z. Experimental study on seismic behavior of steel plate reinforced concrete composite shear wall. Eng. Struct. 2018, 160, 281–292. [Google Scholar] [CrossRef]
  9. Li, X.H.; Li, X.J. Steel plates and concrete filled composite shear walls related nuclear structural engineering: Experimental study for out-of-plane cyclic loading. Nucl. Eng. Des. 2017, 315, 144–154. [Google Scholar] [CrossRef]
  10. Huang, S.T.; Huang, Y.S.; He, A.; Tang, X.; Chen, Q.; Liu, X.; Cai, J. Experimental study on seismic behavior of an innovative composite shear wall. J. Construct. Steel Res. 2018, 148, 165–179. [Google Scholar] [CrossRef]
  11. Rafiei, S.; Hossain, K.M.A.; Lachemi, M.; Behdinan, K.; Anwar, M.S. Finite element modeling of double skin profiled composite shear wall system under in-plane loadings. Eng. Struct. 2013, 56, 46–57. [Google Scholar] [CrossRef]
  12. Hu, H.S.; Nie, J.G.; Eatherton, M.R. Deformation capacity of concrete-filled steel plate composite shear walls. J. Constr. Steel Res. 2014, 103, 148–158. [Google Scholar] [CrossRef]
  13. Booth, P.N.; Varma, A.H.; Sener, K.C.; Mori, K. Seismic behavior and design of a primary shield structure consisting of steel-plate composite (SC) walls. Nucl. Eng. Des. 2015, 295, 829–843. [Google Scholar] [CrossRef]
  14. Nguyen, N.H.; Whittaker, A.S. Numerical modelling of steel-plate concrete composite shear walls. Eng. Struct. 2017, 150, 1–11. [Google Scholar] [CrossRef]
  15. Wang, B.; Jiang, H.; Lu, X. Seismic performance of steel plate reinforced concrete shear wall and its application in China Mainland. J. Construct. Steel Res. 2017, 131, 132–143. [Google Scholar] [CrossRef]
  16. Sato, K. Kitano Masato Experimental Study on Steel Plate Reinforced Concrete Structure Part 23 Bending Shear Tests (Test Results for SC Wall with Opening). In Summary of Academic Speeches; Japanese Architectural Society: Toyko, Japan, 1999; pp. 1227–1228. [Google Scholar]
  17. Satou, K. Experimental Study on Steel Plate Reinforced Concrete Structure Part 24 Bending Shear Tests (Analysis of SC wall with Opening). In Summary of Academic Speeches; Japanese Architectural Society: Toyko, Japan, 1999; pp. 1229–1230. [Google Scholar]
  18. Ishida, M. Experimental Study on Steel Plate Reinforced Concrete Structure Part 25 Bending Shear Tests (Evaluation Method for SC wall with Opening). In Summary of Academic Speeches; Japanese Architectural Society: Toyko, Japan, 1999; pp. 1231–1232. [Google Scholar]
  19. Fujita, T. Experimental Study on Steel Plate Reinforced Concrete Structure Part 26 Shear Tests (Outline of the Experimental Study on SC Panels having Opening). In Summary of Academic Speeches; Japanese Architectural Society: Toyko, Japan, 1999; pp. 123–1234. [Google Scholar]
  20. Osuka. Experimental Study on Steel Plate Reinforced Concrete Structure Part 27 Shear Tests (Discussion of Analytical Results and Experimental ones on SC Panels having Opening). In Summary of Academic Speeches; Japanese Architectural Society: Toyko, Japan, 1999; pp. 1235–1236. [Google Scholar]
  21. Khatir, S.; Wahab, M.A. A computational approach for crack identification in plate structures using XFEM, XIGA, PSO and Jaya algorithm. Theor. Appl. Fract. Mech. 2019, 103, 102240. [Google Scholar] [CrossRef]
  22. Liang, Y.C.; Sun, Y.P. Hole/Crack Identification in Circular Piezoelectric Plates. Procedia Eng. 2014, 79, 194–203. [Google Scholar] [CrossRef] [Green Version]
  23. Khatira, S.; Wahabb, M.A. Fast simulations for solving fracture mechanics inverse problems using POD-RBF XIGA and Jaya algorithm. Eng. Fract. Mech. 2019, 205, 285–300. [Google Scholar] [CrossRef]
  24. Japanese Code (JEAC 4618-2009). Technical Specification for Seismic Design of Steel Plate Concrete Structures; Japan Electric Association: Toyko, Japan, 1999.
  25. Industrial Standard of the People’s Republic of China. Specification for Seismic Test of Building: JGJ/T 101-2015; Ministry of Housing and Urban-Rural Development of the People’s Republic of China: Beijing, China, 2015.
  26. Japanese Architectural Society (AIJ). The Calculation Standards and Specification for Reinforced Concrete Structure; Japan Electric Association: Toyko, Japan, 1999. [Google Scholar]
  27. Ono, M. NISIYAMA taku. Experimental Study on Reinforced Concrete Opening Wall above Opening Periphery Ratio 0.4: Part 2. Area Expansion, Ultimate Strength. In Summary of Academic Speeches; Japanese Architectural Society: Japan, Tokyo, 1995; pp. 147–150. [Google Scholar]
Figure 1. Loading device (a) and measurement arrangement (b).
Figure 1. Loading device (a) and measurement arrangement (b).
Applsci 09 05255 g001
Figure 2. Typical flat specimens.
Figure 2. Typical flat specimens.
Applsci 09 05255 g002
Figure 3. Typical I-shaped specimens.
Figure 3. Typical I-shaped specimens.
Applsci 09 05255 g003
Figure 4. Loading system.
Figure 4. Loading system.
Applsci 09 05255 g004
Figure 5. Bucklingof side plates, pulling failure of weld joints, and concrete crushing of flat steel plate-concrete shear wall (SPSW) specimens with small holes.
Figure 5. Bucklingof side plates, pulling failure of weld joints, and concrete crushing of flat steel plate-concrete shear wall (SPSW) specimens with small holes.
Applsci 09 05255 g005
Figure 6. Failuremodes of I-shaped SPSW specimens with large holes.
Figure 6. Failuremodes of I-shaped SPSW specimens with large holes.
Applsci 09 05255 g006aApplsci 09 05255 g006b
Figure 7. Hysteretic curve of specimens under different stress ratios. (a) SCW-3, (b) SCW-4, and (c) SCW-5.
Figure 7. Hysteretic curve of specimens under different stress ratios. (a) SCW-3, (b) SCW-4, and (c) SCW-5.
Applsci 09 05255 g007
Figure 8. Comparison of the skeleton curves of specimens of the same size under different axial compression ratios.
Figure 8. Comparison of the skeleton curves of specimens of the same size under different axial compression ratios.
Applsci 09 05255 g008
Figure 9. displacement curves of SPSW specimens with different hole sizes. (a) SCW-1, (b) SCW-3, (c) SCW-7, and (d) SCW-8.
Figure 9. displacement curves of SPSW specimens with different hole sizes. (a) SCW-1, (b) SCW-3, (c) SCW-7, and (d) SCW-8.
Applsci 09 05255 g009
Figure 10. Skeleton curves of SPSW specimens with different hole sizes.
Figure 10. Skeleton curves of SPSW specimens with different hole sizes.
Applsci 09 05255 g010
Figure 11. Load displacement curve of specimens reinforced by different thicknesses of plates. (a) SCW-4 and (b) SCW-6.
Figure 11. Load displacement curve of specimens reinforced by different thicknesses of plates. (a) SCW-4 and (b) SCW-6.
Applsci 09 05255 g011
Figure 12. Skeleton curves of specimens reinforced by different thicknesses of plates.
Figure 12. Skeleton curves of specimens reinforced by different thicknesses of plates.
Applsci 09 05255 g012
Figure 13. Hysteretic curves of specimens with holes at different positions. (a) SCW-8 and (b) SCW-9.
Figure 13. Hysteretic curves of specimens with holes at different positions. (a) SCW-8 and (b) SCW-9.
Applsci 09 05255 g013
Figure 14. Skeleton curves of specimens with holes at different positions.
Figure 14. Skeleton curves of specimens with holes at different positions.
Applsci 09 05255 g014
Figure 15. Effective supporting area in the Ono reduction rate calculation method.
Figure 15. Effective supporting area in the Ono reduction rate calculation method.
Applsci 09 05255 g015
Table 1. Parameters of specimens.
Table 1. Parameters of specimens.
Specimen Flange Size (mm)Thickness of Steel Plate (mm)Hole Size (mm)Hole PositionThickness of Stiffening PlateAxial Compression RatioWall Type
WidthThickness
SCW-12.50.3Flat
SCW-22.5125 × 125Center0.15Flat
SCW-32.5125 × 125Center2.50.15Flat
SCW-42.5125 × 125Center2.50.3Flat
SCW-52.5125 × 125Center2.50.5Flat
SCW-62.5125 × 125Center3.50.3Flat
SCW-72.5180 × 180Center2.50.15Flat
SCW-83951102.5430 × 600Center2.50.15I-shaped
SCW-93951102.5430 × 600Eccentricity2.50.15I-shaped
Table 2. Mechanical properties of the steel plate.
Table 2. Mechanical properties of the steel plate.
Thickness of Steel Plate (mm)Yield Strength (MPa)Tensile Strength (MPa)Elasticity Modulus (MPa)Maximum Elongation (%)
2.53694862.02 × 10528.5
Table 3. Mechanical properties of the concrete.
Table 3. Mechanical properties of the concrete.
Material NumberAxial Compressive Strength (MPa)Axial Tension Strength (MPa)Elasticity Modulus (MPa)
C3525.982.333.25 × 104
Table 4. Ultimate loads and displacements of specimens.
Table 4. Ultimate loads and displacements of specimens.
SpecimensUltimate Loads (kN)Ultimate Displacements (mm)
PositiveNegativePositiveNegative
SCW-31100−107418.09−27.05
SCW-41217−118518.46−28.60
SCW-51362−130116.56−13.88
Table 5. Ultimate loads and displacements of specimens.
Table 5. Ultimate loads and displacements of specimens.
SpecimensHole Size (mm)Ultimate Loads (kN)Ultimate Displacements (mm)
PositiveNegativePositiveNegative
SCW-11277−131023.15−19.27
SCW-3125 × 1251100−107418.09−27.05
SCW-7180 × 1801190−110537.43−27.45
SCW-8430 × 6001055−100751.94−43.49
Table 6. Ultimate loads and displacements of specimens.
Table 6. Ultimate loads and displacements of specimens.
SpecimensUltimate Loads (kN)Ultimate Displacements (mm)
PositiveNegativePositiveNegative
SCW-11277−131023.15−19.27
SCW-41217−118518.46−28.60
SCW-61260−130221.41−28.11
Table 7. Ultimate loads and displacements of specimens.
Table 7. Ultimate loads and displacements of specimens.
SpecimensUltimate Loads (kN)Ultimate Displacements (mm)
PositiveNegativePositiveNegative
SCW-81055−100751.94−43.49
SCW-91103−103134.14−44.41
Table 8. Comparison of ultimate loads.
Table 8. Comparison of ultimate loads.
SpecimenStress State Q t e s t   / kN Q c o d e   / kN Q c o d e / Q t e s t Q o n o   / kN Q o n o / Q t e s t Axial Compression/kNType of Walls
SCW-4Stressed118511270.9511350.96950Flat
Tensioned121710980.9011060.91Flat
SCW-6Stressed130211270.8712690.98950Flat
Tensioned126010980.8712370.98Flat
SCW-8Stressed10077340.738200.81320I-shaped
Tensioned10557340.708570.81I-shaped
SCW-9Stressed10317340.718360.81320I-shaped
Tensioned11037340.678360.76I-shaped
Average ratio 0.80 0.88
Notes: Q t e s t is the test result of horizontal ultimate loads. Q c o d e and Q o n o are horizontal ultimate bearing capacities calculated by AIJ codes and the Ono calculation formula.
Table 9. Comparison of lateral stiffness.
Table 9. Comparison of lateral stiffness.
Specimens K t e s t K c o d e K c o d e / K t e s t K o n o K   o n o / K t e s t Axial Compression/kN
SCW-4Negative 41.4356.111.3567.641.63950
Positive65.9045.510.6954.870.83
SCW-6Negative 46.3156.111.2167.641.46950
Positive58.8645.510.7754.870.93
Notes: K t e s t is the test result of lateral stiffness. K c o d e and K o n o are stiffness calculated by AIJ codes and the Ono calculation formula.

Share and Cite

MDPI and ACS Style

Chen, Z.; Wu, J.; Liu, H. Seismic Behavior of Steel Plate-Concrete Shear Walls with Holes. Appl. Sci. 2019, 9, 5255. https://doi.org/10.3390/app9235255

AMA Style

Chen Z, Wu J, Liu H. Seismic Behavior of Steel Plate-Concrete Shear Walls with Holes. Applied Sciences. 2019; 9(23):5255. https://doi.org/10.3390/app9235255

Chicago/Turabian Style

Chen, Zhihua, Jingshu Wu, and Hongbo Liu. 2019. "Seismic Behavior of Steel Plate-Concrete Shear Walls with Holes" Applied Sciences 9, no. 23: 5255. https://doi.org/10.3390/app9235255

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop