Next Article in Journal
The Effects of Green Roofs on Outdoor Thermal Comfort, Urban Heat Island Mitigation and Energy Savings
Next Article in Special Issue
Health Risk Assessment of the Levels of BTEX in Ambient Air of One Urban Site Located in Leon, Guanajuato, Mexico during Two Climatic Seasons
Previous Article in Journal
Influence of Weather on the Behaviour of Tourists in a Beach Destination
Previous Article in Special Issue
PM10 and PM2.5 Qualitative Source Apportionment Using Selective Wind Direction Sampling in a Port-Industrial Area in Civitavecchia, Italy
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Review

Novel Approaches to Air Pollution Exposure and Clinical Outcomes Assessment in Environmental Health Studies

1
Negev Environmental Health Research Institute, Clinical Research Center, Soroka University Medical Center, Beer-Sheva 8457108, Israel
2
Faculty of Health Sciences, Ben-Gurion University of the Negev, Beer-Sheva 8457108, Israel
3
Department of Geography and Environmental Development, Ben-Gurion University of the Negev, Beer-Sheva 8457108, Israel
*
Author to whom correspondence should be addressed.
Atmosphere 2020, 11(2), 122; https://doi.org/10.3390/atmos11020122
Submission received: 27 November 2019 / Revised: 30 December 2019 / Accepted: 17 January 2020 / Published: 21 January 2020
(This article belongs to the Special Issue Exposure Assessment of Air Pollution)

Abstract

:
An accurate assessment of pollutants’ exposure and precise evaluation of the clinical outcomes pose two major challenges to the contemporary environmental health research. The common methods for exposure assessment are based on residential addresses and are prone to many biases. Pollution levels are defined based on monitoring stations that are sparsely distributed and frequently distanced far from residential addresses. In addition, the degree of an association between outdoor and indoor air pollution levels is not fully elucidated, making the exposure assessment all the more inaccurate. Clinical outcomes’ assessment, on the other hand, mostly relies on the access to medical records from hospital admissions and outpatients’ visits in clinics. This method differentiates by health care seeking behavior and is therefore, problematic in evaluation of an onset, duration, and severity of an outcome. In the current paper, we review a number of novel solutions aimed to mitigate the aforementioned biases. First, a hybrid satellite-based modeling approach provides daily continuous spatiotemporal estimations with improved spatial resolution of 1 × 1 km2 and 200 × 200 m2 grid, and thus allows a more accurate exposure assessment. Utilizing low-cost air pollution sensors allowing a direct measurement of indoor air pollution levels can further validate these models. Furthermore, the real temporal-spatial activity can be assessed by GPS tracking devices within the individuals’ smartphones. A widespread use of smart devices can help with obtaining objective measurements of some of the clinical outcomes such as vital signs and glucose levels. Finally, human biomonitoring can be efficiently done at a population level, providing accurate estimates of in-vivo absorbed pollutants and allowing for the evaluation of body responses, by biomarkers examination. We suggest that the adoption of these novel methods will change the research paradigm heavily relying on ecological methodology and support development of the new clinical practices preventing adverse environmental effects on human health.

1. Introduction

There is number of ways in which an air pollution may affect the biosphere, and human health in particular. Pollution is associated with the damaging of food and water supplies while reducing crops yields, damaging wildlife habitats by accelerating arctic warming, triggering climate changes, increasing energy consumption, elevating morbidity burden and millions of premature deaths. According to a global burden of disease report (GBD, 2016), air pollution was ranked as the fifth leading risk factor to disability-adjusted life-years (DALY) and responsible for 7.5% of mortality cases in the world [1].
Research programs investigating the association between air pollution and human health normally encounter two major challenges of exposure assessment and health outcomes evaluation. Methods currently in use for exposure assess have several inherent problems, affecting the way clinical studies evaluate environmental impacts. The following are the common barriers for accurate estimates of the exposure burden (Figure 1): (1) Low spatiotemporal resolution relying on sparse monitoring stations might lead to misclassification bias for patients residing distantly from the monitoring sites [2,3]; (2) lack of the assessment of the indoor air quality [4,5], as most of the models dismiss the difference between the indoor/outdoor pollution and essentially use the outdoor air pollution as a proxy for overall exposure [6,7]; (3) static spatio-temporal approach to the exposure assessment based mostly on residential address and without taking into consideration individuals’ mobility throughout the day [8,9,10,11].
Health outcomes are frequently based on medical records which poses a number of challenges (Figure 2). (1) The use of electronic medical records that might provide inaccurate data and frequently lack information on the onset and the duration of events [12,13,14]; (2) Seeking medical attention is frequently influenced by patients’ self-perception regardless of their clinical state [15,16,17]. Subclinical events, i.e., events without clinical symptoms presentation, are not routinely recorded while can be clinically important [18,19,20,21,22,23,24,25,26]; (3) The need to obtain human tissue samples for measuring of biological indicators that can reveal a plausible biological mechanism is limited due to a small sample size prospective studies plagued by high costs [27,28,29,30,31].
We aimed to review the challenges of both exposure and clinical outcomes assessment, and present novel approaches to face these challenges.

2. Exposure Assessment

Accurate exposure assessment is essential for studying the association between health outcomes and air pollutants. Relying on air pollution measurements from ground-based monitors for health exposure assessment introduces exposure misclassification due to the limited spread of monitors over space and time. The monitors are usually located in urban areas where the spatial and temporal variability in air pollution is high due to variations in human activity [32,33]. These limitations led to the development of various modeling approaches which aim to provide spatiotemporally resolved estimations of different air pollutants and allow improved exposure assessment.
Air pollution exposure models can be divided to the following main classes [6,7,34], each characterized by certain merits and limitations:
(1) Proximity-based assessments that are based on the distance between patients’ locations or their residential address and a certain emission source (e.g., distance to roads [35]), or on the mean of the monitors within a city [3], or simply from the closest monitor [36,37]. The strength of this approach is mainly its simplicity that does not require special expertise; however, its shortcoming is the difficulty to accurately assess the inter-urban variations;
(2) Statistical interpolation that provides estimations using geostatistical techniques (e.g., kriging [38], inverse distance weighting [39]) of air pollutants based on the measurements taken in a network of monitors. This approach might be too simplistic for urban areas that are characterized by high spatial variability of air pollutants derived by local sources. This limitation might be resolved by relying on more advanced geostatistical methods such as universal kriging that combines measured pollutants observations with modelled data [40];
(3) Land use regression models that provide air pollution estimations by calibrating the model using measurements from sparse air quality monitors. Multiple predictors (e.g., land use data, altitude, meteorology, traffic, and roads data) are used in a stochastic model that is applied to unsampled locations [41] in order to provide spatially continuous estimations. Although these models provide spatially resolved predictions, the land-use terms do not vary temporally, thus estimations from such models are relevant mainly for studying association with long term health outcomes [42];
(4) Chemical transport models (CTMs) that simulate dynamics of atmospheric pollutants by combining meteorological and chemical modules. Calculations from such models have shown good agreement with observations in some regions [43,44], however their development is usually computationally intensive, demands detailed input data, and requires expertise in meteorology and climatology to run such models [6]; and
(5) Hybrid models which provide spatiotemporally continuous air pollutants estimates using elements of land use regression that account for the local effect of spatial predictors [34] (e.g., land use data, proximity to roads and emission sources, roads and population density) alongside the effect of various temporal variables such as: meteorology, green space and measures of pollutants from satellite-based remote sensing, and pollutants estimates from CTMs. These models implement different statistical approaches to account for the relationship between pollutants measurements from ground-based devices (monitors or sensors) and various predictors. Both parametric and nonparametric statistical approaches have been used to model this relationship, allowing extending the estimates of air pollutants beyond the limited spread of measurements over space and time.
The models above relate to outdoor pollution exposure assessment methods, however, most of the population spends the majority of their times indoors [45]. Outdoor levels contribution to indoor levels depends on pollutants particles size, ventilation and buildings structures [46], yet indoor activities dominant the indoor pollutants levels [47,48]. This makes understanding the influence of indoor air pollution sources on human health crucial, but quantifying the influence of each source is challenging since information on indoor pollution levels is constructed of various possible sources such as ambient particles penetration to homes and generated indoors particles due to raising pets, air conditioning or heating systems, smoking, cooking, candles, or wood burning and other combustion processes [49,50]. Despite numerous attempts to establish an association function between indoor and outdoor pollution, the levels of the indoor pollution (although arguably more important to the human health) are difficult to ascertain. Our group has attempted to develop such function [51], but the overall accuracy of the approach remains questionable.

2.1. Remote Sensing

The integration of satellite-based remote sensing data in air pollution hybrid models became widely used over the last decade, specifically for particulate matter (PM10 and PM2.5) [7,34], and Nitrogen Dioxide (NO2) [7] assessment. Aerosol optical depth (AOD) is an example of satellite-based products available from the moderate resolution imaging spectroradiometer (MODIS) onboard the Terra and Aqua satellites. It is a measure of the extinction of the solar beam by aerosol particles in the vertical column of atmosphere over a given location and is therefore useful to estimate PM concentrations. Remote sensing data has been also used to provide a product of the total NO2 in the tropospheric column measured by the ozone-monitoring instrument (OMI) on board of the Aura satellite. The strength of remote sensing products is that they constitute real physical measurements of specific air pollutants within the atmospheric column. The availability of satellite-based products from multiple satellite platforms for a sequence of several years made them useful as inputs in air pollution models that aimed to provide spatiotemporally resolved estimations allowing for exploring associations with both short and long-term health effects. Yet, the known challenge is to integrate these products in models that aim to estimate air pollution at breathing level since they provide measurements for the entire atmospheric column between ground level and the satellite. Various statistical approaches were used to incorporate satellite-based products in ground level air pollution hybrid models. One example is the hybrid mixed effects approach that was used to model the relations between ground level measured air pollutants, satellite-based products, and various spatiotemporal predictors. This approach assumes that the relations between ground level air pollution measurements and the satellite-based observations might change on a daily level, and in some cases also by region, therefore the model allows the regression intercepts and slopes of the satellite observations to vary daily and spatially. Using spatially and temporally resolved satellite-based products as a predictor allows extending the air pollution estimates to locations and time points where ground level measurements are absent. This modelling approach was used in different regions, including Europe [52,53], United States (US) [54,55,56,57], China [58], Mexico city [59], and Israel [60,61] to estimate daily PM10 and PM2.5 concentrations in spatial resolution of 1 × 1 km2 and showed good performance with cross validated (cv) total R2 ranging between 0.70–0.92, depending on the area and the specific methodology that was applied. Similar approach was used to estimate daily NO2 concentrations in the US [62], Hong Kong [63], and Switzerland [64] with cv R2 of 0.79, 0.84, and 0.58, respectively.
Ensemble modelling is another common statistical approach [64,65,66,67], that incorporates predictions from multiple base learners, which allows combining their predictive power and creating a final model that outperforms each base learner. A recent model developed for the contiguous US used generalized additive model that accounted for geographic difference to combine PM2.5 estimates from neural network, random forest, and gradient boosting. This model showed good performance with cv R2 of 0.86 for daily PM2.5 predictions [65]. Similar ensemble modelling approach was used over Italy to estimate PM10 and PM2.5 concentrations using estimations from various models (mixed effects model, random forests, extreme gradient boosting and chemical transport model) showing improved model performance in comparison to the individual input models [68]. Random forest (RF) were successfully used to estimate PM10 and PM2.5 concentrations over Italy [67], showing promising results that outperformed previous model that was based on the mixed effects modelling approach [52].
These recent satellite-based hybrid models carried out a preliminary step of filling in using machine learning methods [52,65,67,68]. These models used simulated AOD\NO2 data from chemical transport models (e.g., GEOS-Chem, Community Multiscale Air Quality (CMAQ)) or from the Copernicus Atmosphere Monitoring Service (CAMS) Reanalysis alongside additional predictors such as land-use types, and meteorological variables, day of the year and geographical coordinates.
Some limitations and future research directions should be considered for satellite-based hybrid models. The above mentioned studies estimate daily mean (24 hour) air pollutants level using measurements taken in a spcefic time of day by sattelites with sun-syncronuch orbit. Integration of sattelite-based products from geostationary satellites that provide frequent daytime measurements might be benefical as frequent measurements can be combined and constitute a better predictor of daily (24 hour) mean air pollutants. Future research might also benefit from including satellite-based products with improved spatial and temporal resolution from the new generation of satellites (e.g., the MAIA instrument of NASA and the Sentinel-5 mission of ESA) and possibly provide additional information about the chemical composition of particles. The challenge of modelling air pollution at the ground level might be further addressed by studying the relations between ground-based measurement and products from satellites that provide information about the vertical profile of the atmospheric column. Another direction that should be taken into account in future studies is the integration of measurements from low cost air monitors that will increase their spread to rural areas or provide better spread of measurements whithin urban areas.

2.2. Low Cost Air Pollution Sensors

Several common methods for measurements of particulate matter are used for quantitative and modeling research. The gravimetric principle describes a quantitative determination of an analysis based on the mass of a solid (1405 TEOM Continuous Ambient Air Monitor). Such certified high-precision devices are typically large, stationary and expensive and therefore very sparsely deployed. Typically, only a few stations will cover large urban areas [69]. More fine-grained measurements are important, since exposure levels have been observed to vary even in close proximity during dust storm events. Despite the relatively nearby measurements of dust-PM by portable industrial instruments (such as the portable TSI DustTrak Aerosol Monitor) [70], the accuracy of the assessment for dust atmospheric distribution remains questionable.
The high cost of industrial, certified gravimetric instruments makes their use non-ideal for researches major, extensive research program. Previous studies considered the possibility of using commercial off-the-shelf (COTS) sensors for a more plausible economic solution, giving high temporal resolution along with a wider spatial one [71,72,73,74,75]. Low-cost sensors (typically mini-lasers, electrochemical sensors and metal oxide (MOx) sensors, but also passive samplers) are becoming common in air pollution assessments, although some of the sensors available on the market are delivering highly questionable results. Many of these have detection levels at PPM concentrations far beyond what is found even at pollutant hot spots, which is relevant for many high-risk environments.
Khadem et al, suggested a measurement method, utilizing a node system of spatially distributed smart COTS sensors [76]. Along with a connection to a wireless network at sink nodes, such a system has the potential to increase spatial resolution significantly with limited effects on temporal resolution.
Urban measurements have also shown great promise, when the Indian government sanctioned various experiments to monitor and reduce air pollution levels in major cities (Delhi and Mumbai), including one conducted with COTS sensors [77]. The testing, which was conducted for over a week at the end of December, showed the high temporal resolution that could be gained, while additional factors were able to be taken into consideration: from junctions with slower traffic movement which caused a spike in PM counts, up to 45,000 particles per 0.01 cubic feet (PPCF) compared to the average 20,000 PPCF count, to an empirical decrease a simple face mask could provide in inhalation of said dust (from an average of 9000 PPCF in polluted areas, a decrease of over 50% to less than 4000 PPCF). The comprehensive report has also shown the association between climatological factors to changing air pollution levels, where pollution levels increased by over 400% with rising humidity levels, while temperature levels show an inverse correlation to dust levels.
A similar attempt was made when a participatory urban sensing framework for PM2.5 monitoring with more than 2500 devices (predominantly Plantower G3) was deployed in Taiwan and 29 other countries [78]. Based on two case studies, rising dust levels were seen based on local predictions (holidays, traffic etc.) and were confirmed through mechanisms that assess the data quality based on historical data and nearby devices correlation. GIS (Geographic Information Systems) software was incorporated to spatially present all relevant data for participating cities.
A prototype called HOPES (Hone Pollution Embedded System) was created based on new indices for the indoor air quality (IAQ) criterions [79]. Under the slogan “A cheap and third-age-friendly home device for monitoring indoor air quality” the new approach based on PM and specific gases sensors is beginning to emerge. Furthermore, a recent study took personal measurements a step further, by creating a WSN (wide sensor network) that is capable of sensing different environmental factors: PM2.5, temperature, relative humidity, air pressure and UV radiation [80]. These readings can play a significant role in personal health monitoring and protection. Through the web user interface, each user can assess her ambient environment. Personalized alarms can also be set to notify users to take timely protections when PM2.5 value is above the recommended value.
Exposure assessment based on the mobile phone devices is an another promising direction Outdoor mobile measurements with COTS are still in the works, but more professional instruments have already been used on different platforms (i.e., car, van, pedestrian, bicycle, tram, airship) for mobile monitoring of the various properties of PM. In particular, mobile air quality monitoring is mainly carried out through motor vehicles that can be equipped with voluminous and moderately heavy instruments [81,82,83,84,85]. This poses another issue in data reliability due to pollution caused by said vehicles. To alleviate the disturbances caused by motorized vehicles, Hankey et al. used a bicycle-based system to develop different LUR models for particulate concentrations [86]. A similar attempt was made by Thai et al, who used an instrumented bicycle to elucidate particulate matter exposures over a 14 day period [87].

2.3. Real Time Location Activity and the Use of Smart Devices

Human activities throughout the day determine the burden of individual air pollution exposure. The great variability in human activities, together with their time spent indoors, at work or in traffic, makes the accurate determination of their exposure to air pollution extremely difficult [8,9,88,89]. New methods for ambient air pollution exposure assessment in epidemiological studies were developed in recent years, but they are still predominantly based on the static temporo-spatial approach. Thus, the most prevalent method to estimate personal exposure is based on residential addresses [7]. This method is prone to bias due to a person’s mobility throughout the day that may result in variability in exposure and thus lead to an inaccurate estimation when only home address-based concentrations are taken into account [10,11].
A study conducted in the United States (US) examined the association between residential mobility during pregnancy and possible exposure misclassifications in birth defect studies [90]. The study showed that maternal residential mobility patterns during pregnancy were associated with various socio-demographic characteristics. Their results suggest that birth defects studies that use maternal residential addresses may be subjected to non-differential exposure misclassification. Another study carried out in the US examined the effect of residential mobility of children on estimates of traffic-related air pollution (TRAP), satellite estimated greenspace and socioeconomic characteristics [91]. Estimations based on birth and last known addresses compared to annual address history revealed a significant exposure misclassification. Similarly, disregarding the type of individual daily activity may result in exposure misclassifications. Staying in indoor workplaces, industrial or recreation centers, and driving or spending time in traffic while exposed to TRAP causes the variability in exposure to air pollution [92].
These limitations demonstrate that valid and updated information on the temporal-spatial distribution correlated with the timing and the levels of exposure to air-pollution by real time location, is crucial for the estimation of environmental pollution exposure. So far, the proposed solutions for achieving this level of accuracy were either too expensive or labor intensive.
One of the modern necessities of almost every human today is an ownership of a smart phone. Almost every citizen in developed countries carries a smartphone to help in navigating, communicating, acquiring knowledge and improving the quality of life [93]. According to Ericsson Mobility Report, in 2016 there were 3.8 billion global smartphone users with estimated growing numbers of up to 6.8 billion users by 2022 [94]. The growing number of smartphones can lead to the development of computerized methods to assess individuals’ exposure to air pollution with more precise temporal-spatial resolution [95]. GPS information can also determine the velocity of individuals which can detect whether an individual is in traffic, located at work or sleeps at home, and by that, differentiate their exposure while in different activities. Real-time location tracking using smartphones enables analysis of human behavior and activities, minimizes uncertainties due to human mobility during exposure assessment.
Studies carried out in both Belgium and the US examined the exposure to NO2 [96] and PM2.5 [97] pollutants concentrations using a dynamic approach based on mobile devices and cellular networks to solve the spatial distribution and compared the results to the traditional static residential addresses evaluation method revealed significant differences between two approaches in the exposure quantitation. Another study conducted in the US on a large population scale, demonstrated that measurements of exposure to PM2.5 pollution based on data location derived from mobile devices, compared to data based on residence-only, results in more precise estimates of the particular matter [98].
Time activity patterns assessed by GPS tracking also serves as a tool for advanced personal spatiotemporal exposure assessment models [99]. GPS based individual exposure assessment models evolved from extracting spatiotemporal raw data from daily land-use individuals’ mobile devices to analyzing GPS geo-spatial data and data mining trajectories by highly sophisticated algorithms for outdoor and indoor microenvironments [100]. Assessment of time activity patterns using GPS analysis was also utilized in an experimental prospective study in which exposure to ultrafine particles (UFP) was evaluated in 24 couples (same residential address) of full-time working men and homemaker women, suited with particle counter and GPS monitor [101]. This study found different levels of exposure thus demonstrating the feasibility of the personal GPS monitoring.
Assessing time activity patterns can also be done using mobile devices such as Garmin GPS receivers that can record participants’ location several times a day. These devices were used to evaluate the association between the levels of exposure and the roads type or mode of transportation used [102]. Moreover, integrating the data from the devices with pollution sensors and objective clinical measurements gives insight about spatio-temporally resolved levels of pollution and the health effects of the exposure [103,104].
Mobile phones in recent years are increasingly used as a technological basis for air pollution sensing devices [105]. Using low-cost mobile stations connected to mobile phones enable acquisition of large data quantities and can be used by a large population in a relatively cost-effective manner [106,107]. This method of exposure assessment can provide data on the personal exposure to air pollution and help get high spatio-temporal resolution on urban air pollution assisting for example in municipal planning [108,109]. The limitation of this method is that mobile sensing devices provide data with missing values in both time and space. The missing values can be due to loss of battery power [110], loss of signal in indoor environment [100] or device misuse [111]. Dealing with missing GPS data is challenging and can be handled by methods such as data filtration like selecting days with fewer missing data, smoothing techniques [112], interpolation and imputation of the data [113]. Mendes et al., approached this limitation using kriging technique for data interpolation, showing superiority of this method to the traditional ones [114].

3. Assessment of Clinical Outcomes

Evaluating the outcomes of exposure to air pollution is frequently based on administrative data from health institutions, yet the variability of the medical coding, and the availability and accuracy of the health data, have well known limitations.
The most common method to evaluate the incidence of outcome in environmental studies is based on the events in which the subjects have sought medical attention (e.g., hospital visits or outpatients’ clinics visits). However, assessing the clinical outcomes using medical records poses several problems. First, medical attention is frequently delayed by the patients and is influenced by the patient characteristics such as low medical literacy, social network characteristics, socioeconomic status, severity of the condition and availability of medical services [15,16,17]. In addition, medical records might lack information on the evaluation of the onset and the duration of the event, e.g., in of the analysis of atrial fibrillation (AF) it is important to determine the start and the duration of the event [12,13,14]. Finally, subclinical events, i.e., events without clinical presentation such as elevated glucose [25,26], elevated blood pressure [23,24], subclinical AF [20,21] etc. [18,19,22], are not routinely recorded. These limitations can narrow the outcome assessment and introduce bias in the estimation of the effects of air pollution on health outcomes.

3.1. Utilization of Smart Devices

In recent years there has been a growing use of smart devices and wearable devices for assessing clinical health outcomes in different fields. The devices can be used to detect the development of diabetes [115], to monitor glucose levels [116] and levels of glycated hemoglobin [117], to record symptoms related to Chronic Obstructive Pulmonary Disease (COPD) [118] and to improve blood pressure control using self-management systems [119]. These studies have demonstrated how patients’ health can be improved by incorporating smart devices into medical practice, yet frequently the use of these devices relays on the patient collaboration and greatly depend on unbiased patient reports that can result in misclassifications of the outcome [117].
In the field of cardiovascular medicine, the implantable cardioverter defibrillator (ICD) and pacemakers can be used for detecting cardiac arrhythmias since these devices are capable of recording and analyzing abnormal heart rate events. Several studies have examined the importance of these devices for the detection of new onset of AF [120] and asymptomatic AF [121,122]. However, the inherent limitation of the health information provided by these devices is that it is pertinent to a selected group of patients in whom the use of these devices was clinically indicated.
Smart devices such as wrist bands and smart watches have been used for assessing abnormalities in cardiac rhythm [123], AF and asymptomatic AF [124], without the constrains of the subjective patients reports and without the need to constantly validate the data. A recent study used smart Apple Watches to detect cases of an irregular heart pulse in the general population, thus creating for the first time a prospective large-scale study that identifies subclinical events [125].
However, the use of the smart devices has a number of limitations: first, the efficacy of the smart watches for detecting clinical events was still not evaluated in clinical trials; furthermore, patients are frequently non-compliant with the requirement of fulfilling personal diaries, unlike in traditional studies during which patients are closely monitored for all clinical events. Additionally, use of smart devices requires a certain degree of technological literacy, thus limiting their use to younger population groups. Another limitation is the smart phones’ energy consumption and the need for frequent charging [126,127], which needs to be addressed for example by the development of the energy-efficient algorithms [128] In addition clinical and physiological data ascertainment via mobile phones poses a number of challenges: (1) Accurate, "medical grade" data acquisition. Only lately FDA approved devices capable of providing ECG tracking; (2) Data processing and optimization, which requires threshold-based methods [129]; (3) Data transfer which is usually done by third-party systems which might result in random and partial data transfers. This can be addressed by applications that provide fixed transfers times [130]; (4) Data storage, especially of the large volume longitudinal signals such as blood pressure, ECG etc. An efficient solution requires cloud storage services [131]. Lastly, although not within the scope of the current manuscript, the serious issues of the health data privacy must be addressed on the legislative level. Missing values of measured clinical parameters such as heart rates and ECG can be a consequence of lack of charging and misfunctions of the devices due to technical problems [132]. This can be handled using methods such as data interpolation [133] and imputation [134].

3.2. Human Biomonitoring

The underlying assumption of ecological research is that ambient outdoor air pollution is a valid proxy of the true individual levels of exposure. Nevertheless, the health effect of an ambient exposure is frequently confounded by socio-economic status, occupation, smoking and other factors, that are hard to account for in a standard analysis, resulting in spurious or biased associations.
We believe that measurable biological indicators sampled from human tissues are required to validate the current ecological methods of exposure assessments. Furthermore, this approach will extend our insight on the plausible biological mechanisms which contribute to the pathophysiology of the environmental health effects.
Biologic indicators or biomarkers include biochemical, molecular, genetic, immunologic, or physiologic signals [135]. Human biomonitoring (HBM) is frequently used worldwide to estimate the extent of exposure of populations to potentially dangerous chemical substances [136]. However, HBM studies have been used mainly in the occupational-health field [137,138,139]. Yet, recently the focus has changed towards the assessment of an environmental exposure in the general population. For instance, an HBM of environmental chemicals in the Canadian Health Measures Survey is a comprehensive initiative providing general population HBM data in Canada. It is an ongoing cross-sectional survey implemented in 2 year cycles with an enrollment of up to 7000 people in each cycle. Its recent 2016 report presented the information on biomonitoring results for 279 chemicals; approximately half of the chemicals measured in individual’s blood and urine samples were detected in more than 60% of the samples [140].
The Center for Disease Control (CDC) and Prevention have been providing similar information on the nationally representative biomonitoring data in the general population in the US since 1999. The CDC reports present analyses of blood, serum, and urine samples from random subsamples of 2 year surveys (National Health and Nutrition Survey–NHANES), typically including up to 6000–7000 participants at each round, and an extensive list of chemicals tested [141].
Biomarkers have an additional role related to environmental health research; validation of the causal relationship between air pollution exposure and health outcomes by revealing of a plausible biologic mechanism. Studies have examined the effect of pollutants on biomarkers expression in different human tissues such as adipose tissue [29], cardiomyocytes [30], lung epithelial cells [31], and blood [28]. For instance, the Multi-Ethnic Study of Atherosclerosis (MESA) showed that the PM2.5 exposure was correlated with an increase in blood concentration of C-reactive protein (CRP), fibrinogen and E-selectin [142], markers related to the atherogenic process [143,144,145], suggesting a plausible biological mechanism by which air pollution could contribute to the development of cardiovascular diseases.
The main problem with conducting such a survey is a potential bias introduced through the sampling design and the participant selection, e.g., subjects with higher socioeconomic status and women are more likely to participate in such studies [146]. The WHO recommends a minimum of 120 randomly selected individuals per population group to allow for the estimation of group-specific reference values with sufficient precision and meaningful comparison of population groups in surveys. Additionally, the high cost for obtaining and analyzing each sample in such studies is extremally high, ranging from less than €100 for metals to €800 for dioxins [147].

Population Biomonitoring

We recently have developed an innovative cost-effective approach to population biomonitoring based on the national blood banking system. The method is based on analyzing the blood donations collected and processed daily in Israel.
The use of blood from blood donors for research objectives is previously described; e.g., the Danish Blood Donor Study (DBDS), a large-scale research project and biobank established in 2010 [148]. Although numerous studies were conducted via the extensive database of blood donors, showing associations between risk factors, biomarkers, health effects, and diseases, to this date, the use of the blood banking for the human biomonitoring is yet to be widely established.
Based on the established blood bank system, blood samples of donors can be tested for the detection of different pollutants. Per National Blood Bank regulation, the serum separated from the unit of the blood is to be stored for the period of one year. The donors are routinely consented to the testing of the stored plasma. Levels of the pollutants’ concentration levels can then be linked with the air pollution and meteorological data assessed at the location of blood collection services (short-term exposure) and at the donors’ permanent address (medium and long-term exposure), by using satellite-based exposure models. The sampling method of donations used for such studies can be aimed to create geographically representative cohorts for different areas. Repeated testing for recurrent donors in certain regions will provide indication on changing trends in exposure in these areas.
This method has a number of advantages. First, the tested population comprised healthy volunteers who represent an ideal population for the precise assessment of the environmental exposure, as they are not treated with medications and conduct an active lifestyle; second, 80% of the blood donors are returning donors, thus, repeated testing for recurrent donors in the population will provide indication on changing trends in exposure in the area; lastly, as blood donation stations are spread all over the country, the population of donors will serve a geographically valid proxy for the general population. The method has some challenges as well with the main being the use of the collection and storage equipment not specifically designed for the measurement of the low concentrations of the potential pollutants, i.e., possibility of the contamination. In addition, the specific medium to be used for the pollutants testing can be different from the usual standard for blood banking. For instance, our preliminary experiment demonstrated that only whole blood would reflect the actual concentration of some of the heavy metals in the blood, while only the serum is routinely collected and stored in the National Blood Bank.
The important consequence of such studies is the establishment of a framework of dynamic national biomonitoring by repeatedly assessing the exposure to selected chemicals and pollutants. In the future, daily assessments of potentially hazardous elements in the donated blood will allow to map the areas of exposure. Furthermore, the information collected in proposed surveys can lead to a new paradigm of tailored environmental preventions measures.

4. Conclusions

The environmental health research faces the inherent problem of the balance between the desire to assess a population on a wider scale and ability to obtain an accurate exposures and outcomes data. So far, we have been forced to sacrifice one goal to achieve another; the researchers could assess large populations using an ecological design with imprecise exposure assessment of conduct personal exposure studies on a small scale. Latest development in the field of the exposure assessment together with the ability to access detailed clinical data is changing the research paradigm. Estimation of real-time location-activity using GPS tracking of cellular phones together with a high-resolution hybrid satellite model that can measure pollutants levels with a spatial resolution of up to 1 × 1 km2 allows for a precise spatio-temporal solution. Wearable devices will provide continuous real time clinical measurements altering the way the health data is being collected and assessed. Smart devices combined with real time location activity retain information on exact locations and timeframes in which populations were exposed to different hazards. Human biomonitoring samples can help better understand both the dose of pollutants the body absorbs and the plausible biological mechanisms which contribute to the health outcome. Finally, the use of advanced computational and statistical approaches incorporating the elements of the machine learning can provided the new analytical framework. We believe that the described approaches will allow us to develop novel diagnostic and treatment tools to address the environmental effects on human health, which in turn, will be adopted by the clinical community.

Author Contributions

Conceptualization, L.N., I.K. (Itzhak Katra), I.K. (Itai Kloog), and V.N.; investigation, S.Y., L.H., A.S., and D.L.; writing—original draft preparation, S.Y.; writing—review and editing, L.N. and V.N.; visualization, S.Y.; supervision, V.N. All authors have read and agreed to the published version of the manuscript.

Funding

This research received no external funding.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Gakidou, E.; Afshin, A.; Abajobir, A.A.; Abate, K.H.; Abbafati, C.; Abbas, K.M.; Abd-Allah, F.; Abdulle, A.M.; Abera, S.F.; Aboyans, V.; et al. Global, regional, and national comparative risk assessment of 84 behavioural, environmental and occupational, and metabolic risks or clusters of risks, 1990–2016: A systematic analysis for the Global Burden of Disease Study 2016. Lancet 2017, 390, 1345–1422. [Google Scholar] [CrossRef] [Green Version]
  2. Zeger, S.L.; Thomas, D.; Dominici, F.; Samet, J.M.; Dockery, D.; Cohen, A. Exposure measurement error in time-series studies of air pollution: Concepts and consequences. Environ. Health Perspect. 2000, 108, 419–426. [Google Scholar] [CrossRef] [PubMed]
  3. Pope, C.A.; Burnett, R.T.; Thun, M.J.; Calle, E.E.; Krewski, D.; Ito, K.; Thurston, G.D. Lung cancer, cardiopulmonary mortality, and long-term exposure to fine particulate air pollution. J. Am. Med. Assoc. 2002, 287, 1132–1141. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  4. Baek, S.O.; Kim, Y.S.; Perry, R. Indoor air quality in homes, offices and restaurants in Korean urban areas—Indoor/outdoor relationships. Atmos. Environ. 1997, 31, 529–544. [Google Scholar] [CrossRef]
  5. Leung, D.Y.C. Outdoor-indoor air pollution in urban environment: Challenges and opportunity. Front. Environ. Sci. 2015, 2, 69. [Google Scholar] [CrossRef]
  6. Jerrett, M.; Arain, A.; Kanaroglou, P.; Beckerman, B.; Potoglou, D.; Sahsuvaroglu, T.; Morrison, J.; Giovis, C. A review and evaluation of intraurban air pollution exposure models. J. Expo. Anal. Environ. Epidemiol. 2005, 15, 1–20. [Google Scholar] [CrossRef]
  7. Hoek, G. Methods for Assessing Long-Term Exposures to Outdoor Air Pollutants. Curr. Environ. Health Rep. 2017, 4, 450–462. [Google Scholar] [CrossRef]
  8. Pas, E.I.; Koppelman, F.S. An examination of the determinants of day-to-day variability in individuals’ urban travel behavior. Transportation 1987, 14, 3–20. [Google Scholar] [CrossRef]
  9. Wu, X.; Bennett, D.H.; Lee, K.; Cassady, D.L.; Ritz, B.; Hertz-Picciotto, I. Longitudinal variability of time-location/activity patterns of population at different ages: A longitudinal study in California. Environ. Health 2011, 10, 80. [Google Scholar] [CrossRef] [Green Version]
  10. Setton, E.; Marshall, J.D.; Brauer, M.; Lundquist, K.R.; Hystad, P.; Keller, P.; Cloutier-Fisher, D. The impact of daily mobility on exposure to traffic-related air pollution and health effect estimates. J. Expo. Sci. Environ. Epidemiol. 2011, 21, 42–48. [Google Scholar] [CrossRef] [Green Version]
  11. Park, Y.M.; Kwan, M.P. Individual exposure estimates may be erroneous when spatiotemporal variability of air pollution and human mobility are ignored. Health Place 2017, 43, 85–94. [Google Scholar] [CrossRef] [PubMed]
  12. Majeed, A.; Car, J.; Sheikh, A. Accuracy and completeness of electronic patient records in primary care. Fam. Pract. 2008, 25, 213–214. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  13. Hogan, W.R.; Wagner, M.M. Accuracy of Data in Computer-based Patient Records. J. Am. Med. Inf. Assoc. 1997, 4, 342–355. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  14. Stewart, A.L.; Lynch, K.J. Identifying discrepancies in electronic medical records through pharmacist medication reconciliation. J. Am. Pharm. Assoc. 2012, 52, 59–68. [Google Scholar] [CrossRef]
  15. Matthews, K.A.; Siegel, J.M.; Kuller, L.H.; Thompsonk, M.; Varat, M. Determinants of decisions to seek medical treatment by patients with acute myocardial infarction symptoms. J. Personal. Soc. Psychol. 1983, 44, 1144–1156. [Google Scholar] [CrossRef]
  16. Berkanovic, E.; Telesky, C.; Reeder, S. Structural and social psychological factors in the decision to seek medical care for symptoms. Med. Care 1981, 19, 693–709. [Google Scholar] [CrossRef]
  17. Berkanovic, E.; Telesky, C. Social networks, beliefs, and the decision to seek medical care: An analysis of congruent and incongruent patterns. Med. Care 1982, 20, 1018–1026. [Google Scholar] [CrossRef]
  18. Haentjens, P.; van Meerhaeghe, A.; Poppe, K.; Velkeniers, B. Subclinical thyroid dysfunction and mortality: An estimate of relative and absolute excess all-cause mortality based on time-to-event data from cohort studies. Eur. J. Endocrinol. 2008, 159, 329–341. [Google Scholar] [CrossRef] [Green Version]
  19. Aichner, F.T.; Topakian, R.; Alberts, M.J.; Bhatt, D.L.; Haring, H.P.; Hill, M.D.; Montalescot, G.; Goto, S.; Touzé, E.; Mas, J.L.; et al. High cardiovascular event rates in patients with asymptomatic carotid stenosis: The REACH registry. Eur. J. Neurol. 2009, 16, 902–908. [Google Scholar] [CrossRef]
  20. Roche, F.; Gaspoz, J.M.; Da Costa, A.; Isaaz, K.; Duverney, D.; Pichot, V.; Costes, F.; Lacour, J.R.; Barthélémy, J.C. Frequent and prolonged asymptomatic episodes of paroxysmal atrial fibrillation revealed by automatic long-term event recorders in patients with a negative 24-hour Holter. Pace—Pacing Clin. Electrophysiol. 2002, 25, 1587–1593. [Google Scholar] [CrossRef] [Green Version]
  21. Page, R.L.; Wilkinson, W.E.; Clair, W.K.; McCarthy, E.A.; Pritchett, E.L.C. Asymptomatic arrhythmias in patients with symptomatic paroxysmal atrial fibrillation and paroxysmal supraventricular tachycardia. Circulation 1994, 89, 224–227. [Google Scholar] [CrossRef] [Green Version]
  22. Matsui, Y.; Eguchi, K.; Ishikawa, J.; Hoshide, S.; Shimada, K.; Kario, K. Subclinical Arterial Damage in Untreated Masked Hypertensive Subjects Detected by Home Blood Pressure Measurement. Am. J. Hypertens. 2007, 20, 385–391. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  23. Allen, N.B.; Siddique, J.; Wilkins, J.T.; Shay, C.; Lewis, C.E.; Goff, D.C.; Jacobs, D.R.; Liu, K.; Lloyd-Jones, D. Blood pressure trajectories in early adulthood and subclinical atherosclerosis in middle age. J. Am. Med. Assoc. 2014, 311, 490–497. [Google Scholar] [CrossRef] [PubMed]
  24. McEvoy, J.W.; Chen, Y.; Rawlings, A.; Hoogeveen, R.C.; Ballantyne, C.M.; Blumenthal, R.S.; Coresh, J.; Selvin, E. Diastolic Blood Pressure, Subclinical Myocardial Damage, and Cardiac Events: Implications for Blood Pressure Control. J. Am. Coll. Cardiol. 2016, 68, 1713–1722. [Google Scholar] [CrossRef] [PubMed]
  25. Catalano, P.M.; Bernstein, I.M.; Wolfe, R.R.; Srikanta, S.; Tyzbir, E.; Sims, E.A.H. Subclinical abnormalities of glucose metabolism in subjects with previous gestational diabetes. Am. J. Obstet. Gynecol. 1986, 155, 1255–1262. [Google Scholar] [CrossRef]
  26. Saydah, S.H.; Loria, C.M.; Eberhardt, M.S.; Brancati, F.L. Subclinical states of glucose intolerance and risk of death in the U.S. Diabetes Care 2001, 24, 447–453. [Google Scholar] [CrossRef] [Green Version]
  27. Balti, E.V.; Echouffo-Tcheugui, J.B.; Yako, Y.Y.; Kengne, A.P. Air pollution and risk of type 2 diabetes mellitus: A systematic review and meta-analysis. Diabetes Res. Clin. Pract. 2014, 106, 161–172. [Google Scholar] [CrossRef]
  28. Schwartz, J. Air pollution and blood markers of cardiovascular risk. Environ. Health Perspect. 2001, 109, 405–409. [Google Scholar]
  29. Hassan, L.; Pecht, T.; Goldstein, N.; Haim, Y.; Kloog, I.; Yarza, S.; Sarov, B.; Novack, V. The effects of ambient particulate matter on human adipose tissue. J. Toxicol. Environ. Health Part A Curr. 2019. [Google Scholar] [CrossRef]
  30. Yang, X.; Feng, L.; Zhang, Y.; Hu, H.; Shi, Y.; Liang, S.; Zhao, T.; Fu, Y.; Duan, J.; Sun, Z. Cytotoxicity induced by fine particulate matter (PM 2.5) via mitochondria-mediated apoptosis pathway in human cardiomyocytes. Ecotoxicol. Environ. Saf. 2018, 161, 198–207. [Google Scholar] [CrossRef]
  31. Carter, J.D.; Ghio, A.J.; Samet, J.M.; Devlin, R.B. Cytokine production by human airway epithelial cells after exposure to an air pollution particle is metal-dependent. Toxicol. Appl. Pharmcol. 1997, 146, 180–188. [Google Scholar] [CrossRef] [PubMed]
  32. Zhu, Y.; Hinds, W.C.; Kim, S.; Shen, S.; Sioutas, C. Study of ultrafine particles near a major highway with heavy-duty diesel traffic. Atmos. Environ. 2002, 36, 4323–4335. [Google Scholar] [CrossRef]
  33. Eeftens, M.; Tsai, M.Y.; Ampe, C.; Anwander, B.; Beelen, R.; Bellander, T.; Cesaroni, G.; Cirach, M.; Cyrys, J.; De Hoogh, K.; et al. Spatial variation of PM2.5, PM10, PM2.5 absorbance and PMcoarse concentrations between and within 20 European study areas and the relationship with NO2—Results of the ESCAPE project. Atmos. Environ. 2012, 62, 303–317. [Google Scholar] [CrossRef]
  34. Sorek-Hamer, M.; Just, A.C.; Kloog, I. Satellite remote sensing in epidemiological studies. Curr. Opin. Pediatr. 2016, 28, 228–234. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  35. Hoek, G.; Brunekreef, B.; Goldbohm, S.; Fischer, P.; van den Brandt, P.A. Association between mortality and indicators of traffic-related air pollution in the Netherlands: A cohort study. Lancet 2002, 360, 1203–1209. [Google Scholar] [CrossRef] [Green Version]
  36. Ostro, B.; Lipsett, M.; Reynolds, P.; Goldberg, D.; Hertz, A.; Garcia, C.; Henderson, K.D.; Bernstein, L. Long-term exposure to constituents of fine particulate air pollution and mortality: Results from the California Teachers Study. Environ. Health Perspect. 2010, 118, 363–369. [Google Scholar] [CrossRef] [Green Version]
  37. Hoek, G.; Pattenden, S.; Willers, S.; Antova, T.; Fabianova, E.; Braun-Fahrländer, C.; Forastiere, F.; Gehring, U.; Luttmann-Gibson, H.; Grize, L.; et al. PM10, and children’s respiratory symptoms and lung function in the PATY study. Eur. Respir. J. 2012, 40, 538–547. [Google Scholar] [CrossRef] [Green Version]
  38. Künzli, N.; Jerrett, M.; Mack, W.J.; Beckerman, B.; LaBree, L.; Gilliland, F.; Thomas, D.; Peters, J.; Hodis, H.N. Ambient air pollution and atherosclerosis in Los Angeles. Environ. Health Perspect. 2005, 113, 201–206. [Google Scholar] [CrossRef]
  39. Beelen, R.; Hoek, G.; Van den Brandt, P.A.; Goldbohm, R.A.; Fischer, P.; Schouten, L.J.; Jerrett, M.; Hughes, E.; Armstrong, B.; Brunekreef, B. Long-term effects of traffic-related air pollution on mortality in a Dutch cohort (NLCS-AIR study). Environ. Health Perspect. 2008, 116, 196–202. [Google Scholar] [CrossRef]
  40. Schneider, P.; Castell, N.; Vogt, M.; Dauge, F.R.; Lahoz, W.A.; Bartonova, A. Mapping urban air quality in near real-time using observations from low-cost sensors and model information. Environ. Int. 2017, 106, 234–247. [Google Scholar] [CrossRef]
  41. Hoek, G.; Beelen, R.; De Hoogh, K.; Vienneau, D.; Gulliver, J.; Fischer, P.; Briggs, D. A review of land-use regression models to assess spatial variation of outdoor air pollution. Atmos. Environ. 2008, 42, 7561–7578. [Google Scholar] [CrossRef]
  42. De Hoogh, K.; Gulliver, J.; Donkelaar, A.V.; Martin, R.V.; Marshall, J.D.; Bechle, M.J.; Cesaroni, G.; Pradas, M.C.; Dedele, A.; Eeftens, M.; et al. Development of West-European PM2.5 and NO2 land use regression models incorporating satellite-derived and chemical transport modelling data. Environ. Res. 2016, 151, 1–10. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  43. Manders, A.M.M.; Builtjes, P.J.H.; Curier, L.; Denier van der Gon, H.A.C.; Hendriks, C.; Jonkers, S.; Kranenburg, R.; Kuenen, J.J.P.; Segers, A.J.; Timmermans, R.M.A.; et al. Curriculum vitae of the LOTOS-EUROS (v2.0) chemistry transport model. Geosci. Model Dev. 2017, 10, 4145–4173. [Google Scholar] [CrossRef] [Green Version]
  44. Hertel, O.; Jensen, S.S.; Ketzel, M.; Becker, T.; Peel, R.G.; Ørby, P.V.; Skjøth, C.A.; Ellermann, T.; Raaschou-Nielsen, O.; Sørensen, M.; et al. Utilizing monitoring data and spatial analysis tools for exposure assessment of atmospheric pollutants in Denmark. ACS Symp. Ser. 2013, 1149, 95–122. [Google Scholar]
  45. Klepeis, N.E.; Nelson, W.C.; Ott, W.R.; Robinson, J.P.; Tsang, A.M.; Switzer, P.; Behar, J.V.; Hern, S.C.; Engelmann, W.H. The National Human Activity Pattern Survey (NHAPS): A resource for assessing exposure to environmental pollutants. J. Expo. Anal. Environ. Epidemiol. 2001, 11, 231–252. [Google Scholar] [CrossRef] [Green Version]
  46. Chen, C.; Zhao, B. Review of relationship between indoor and outdoor particles: I/O ratio, infiltration factor and penetration factor. Atmos. Environ. 2011, 45, 275–288. [Google Scholar] [CrossRef]
  47. Massey, D.; Masih, J.; Kulshrestha, A.; Habil, M.; Taneja, A. Indoor/outdoor relationship of fine particles less than 2.5 μm (PM2.5) in residential homes locations in central Indian region. Build. Environ. 2009, 44, 2037–2045. [Google Scholar] [CrossRef]
  48. Jones, N.C.; Thornton, C.A.; Mark, D.; Harrison, R.M. Indoor/outdoor relationships of particulate matter in domestic homes with roadside, urban and rural locations. Atmos. Environ. 2000, 34, 2603–2612. [Google Scholar] [CrossRef]
  49. Lee, S.C.; Li, W.M.; Ao, C.H. Investigation of indoor air quality at residential homes in Hong Kong—Case study. Atmos. Environ. 2002, 36, 225–237. [Google Scholar] [CrossRef]
  50. Chao, C.Y.H.; Tung, T.C.W.; Burnett, J. Influence of different indoor activities on the indoor particulate levels in residential buildings. Indoor Built Environ. 1998, 7, 110–121. [Google Scholar] [CrossRef]
  51. Krasnov, H.; Katra, I.; Novack, V.; Vodonos, A.; Friger, M.D. Increased indoor PM concentrations controlled by atmospheric dust events and urban factors. Build. Environ. 2015, 87, 169–176. [Google Scholar] [CrossRef]
  52. Stafoggia, M.; Schwartz, J.; Badaloni, C.; Bellander, T.; Alessandrini, E.; Cattani, G.; De’ Donato, F.; Gaeta, A.; Leone, G.; Lyapustin, A.; et al. Estimation of daily PM10 concentrations in Italy (2006–2012) using finely resolved satellite data, land use variables and meteorology. Environ. Int. 2017, 99, 234–244. [Google Scholar] [CrossRef] [PubMed]
  53. De Hoogh, K.; Héritier, H.; Stafoggia, M.; Künzli, N.; Kloog, I. Modelling daily PM2.5 concentrations at high spatio-temporal resolution across Switzerland. Environ. Pollut. 2018, 233, 1147–1154. [Google Scholar] [CrossRef] [PubMed]
  54. Chudnovsky, A.A.; Koutrakis, P.; Kloog, I.; Melly, S.; Nordio, F.; Lyapustin, A.; Wang, Y.; Schwartz, J. Fine particulate matter predictions using high resolution Aerosol Optical Depth (AOD) retrievals. Atmos. Environ. 2014, 89, 189–198. [Google Scholar] [CrossRef] [Green Version]
  55. Beckerman, B.S.; Jerrett, M.; Serre, M.; Martin, R.V.; Lee, S.J.; van Donkelaar, A.; Ross, Z.; Su, J.; Burnett, R.T. A hybrid approach to estimating national scale spatiotemporal variability of PM2.5 in the contiguous United States. Environ. Sci. Technol. 2013, 47, 7233–7241. [Google Scholar]
  56. Lee, M.; Kloog, I.; Chudnovsky, A.; Lyapustin, A.; Wang, Y.; Melly, S.; Coull, B.; Koutrakis, P.; Schwartz, L. Spatiotemporal prediction of fine particulate matter using high-resolution satellite images in the Southeastern US 2003-2011. J. Exp. Sci. Environ. Epidemiol. 2016, 26, 377–384. [Google Scholar] [CrossRef] [Green Version]
  57. Kloog, I.; Nordio, F.; Coull, B.A.; Schwartz, J. Incorporating local land use regression and satellite aerosol optical depth in a hybrid model of spatiotemporal PM2.5 exposures in the mid-atlantic states. Environ. Sci. Technol. 2012, 46, 11913–11921. [Google Scholar] [CrossRef] [Green Version]
  58. Ma, Z.; Liu, Y.; Zhao, Q.; Liu, M.; Zhou, Y.; Bi, J. Satellite-derived high resolution PM2.5 concentrations in Yangtze River Delta Region of China using improved linear mixed effects model. Atmos. Environ. 2016, 133, 156–164. [Google Scholar] [CrossRef]
  59. Just, A.C.; Wright, R.O.; Schwartz, J.; Coull, B.A.; Baccarelli, A.A.; Tellez-Rojo, M.M.; Moody, E.; Wang, Y.; Lyapustin, A.; Kloog, I. Using High-Resolution Satellite Aerosol Optical Depth to Estimate Daily PM2.5 Geographical Distribution in Mexico City. Environ. Sci. Technol. 2015, 49, 8576–8584. [Google Scholar]
  60. Shtein, A.; Karnieli, A.; Katra, I.; Raz, R.; Levy, I.; Lyapustin, A.; Dorman, M.; Broday, D.M.; Kloog, I. Estimating daily and intra-daily PM10 and PM2.5 in Israel using a spatio-temporal hybrid modeling approach. Atmos. Environ. 2018, 191, 142–152. [Google Scholar] [CrossRef]
  61. Kloog, I.; Sorek-Hamer, M.; Lyapustin, A.; Coull, B.; Wang, Y.; Just, A.C.; Schwartz, J.; Broday, D.M. Estimating daily PM2.5 and PM10 across the complex geo-climate region of Israel using MAIAC satellite-based AOD data. Atmos. Environ. 2015, 122, 409–416. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  62. Lee, H.J.; Koutrakis, P. Daily ambient NO2 concentration predictions using satellite ozone monitoring instrument NO2 data and land use regression. Environ. Sci. Technol. 2014, 48, 2305–2311. [Google Scholar] [PubMed]
  63. Anand, J.S.; Monks, P.S. Estimating daily surface NO2 concentrations from satellite data—A case study over Hong Kong using land use regression models. Atmos. Chem. Phys. 2017, 17, 8211–8230. [Google Scholar] [CrossRef] [Green Version]
  64. De Hoogh, K.; Saucy, A.; Shtein, A.; Schwartz, J.; West, E.A.; Strassmann, A.; Puhan, M.; Röösli, M.; Stafoggia, M.; Kloog, I. Predicting Fine-Scale Daily NO2 for 2005–2016 Incorporating OMI Satellite Data Across Switzerland. Environ. Sci. Technol. 2019, 53, 10279–10287. [Google Scholar] [CrossRef] [PubMed]
  65. Di, Q.; Amini, H.; Shi, L.; Kloog, I.; Silvern, R.; Kelly, J.; Sabath, M.B.; Choirat, C.; Koutrakis, P.; Lyapustin, A.; et al. An ensemble-based model of PM2.5 concentration across the contiguous United States with high spatiotemporal resolution. Environ. Int. 2019, 130, 104909. [Google Scholar] [CrossRef] [PubMed]
  66. Murray, N.; Chang, H.H.; Holmes, H.; Liu, Y. Combining Satellite Imagery and Numerical Model Simulation to Estimate Ambient Air Pollution: An Ensemble Averaging Approach. arXiv 2018, arXiv:1802.03077. [Google Scholar] [CrossRef]
  67. Stafoggia, M.; Bellander, T.; Bucci, S.; Davoli, M.; de Hoogh, K.; De’ Donato, F.; Gariazzo, C.; Lyapustin, A.; Michelozzi, P.; Renzi, M.; et al. Estimation of daily PM10 and PM2.5 concentrations in Italy, 2013–2015, using a spatiotemporal land-use random-forest model. Environ. Int. 2019, 124, 170–179. [Google Scholar] [CrossRef]
  68. Shtein, A.; Kloog, I.; Schwartz, J.; Silibello, C.; Michelozzi, P.; Gariazzo, C.; Viegi, G.; Forastiere, F.; Karnieli, A.; Just, A.C.; et al. Estimating daily PM2.5 and PM10 over Italy using an ensemble model. Environ. Sci. Technol. 2019, 54, 120–128. [Google Scholar] [CrossRef]
  69. Budde, M.; el Masri, R.; Riedel, T.; Beigl, M. Enabling low-cost particulate matter measurement for participatory sensing scenarios. In Proceedings of the 12th International Conference on Mobile and Ubiquitous Multimedia, Lulea, Sweden, 2–5 December 2013. [Google Scholar]
  70. Krasnov, H.; Kloog, I.; Friger, M.; Katra, I. The spatio-temporal distribution of particulate matter during natural dust episodes at an urban scale. PLoS ONE 2016, 11, e0160800. [Google Scholar] [CrossRef]
  71. Li, L.; Zheng, Y.; Zhang, L. Demonstration abstract: PiMi air box—A cost-effective sensor for participatory indoor quality monitoring. In Proceedings of the 13th International Symposium on Information Processing in Sensor Networks, Berlin, Germany, 15–17 April 2014; pp. 327–328. [Google Scholar]
  72. Hera, M.R.; Rahman, A.; Afrin, A.; Uddin, M.Y.S.; Venkatasubramanian, N. AQBox: An air quality measuring box from COTS gas sensors. In Proceedings of the 2017 International Conference on Networking, Systems and Security, Dhaka, Bangladesh, 5–8 January 2017; pp. 191–194. [Google Scholar]
  73. Budde, M.; Busse, M.; Beigl, M. Investigating the use of commodity dust sensors for the embedded measurement of particulate matter. In Proceedings of the 9th International Conference on Networked Sensing Systems, INSS 2012, Antwerp, Belgium, 11–14 June 2012. [Google Scholar]
  74. Chung, W.Y.; Oh, S.J. Remote monitoring system with wireless sensors module for room environment. Sens. Actuators B Chem. 2006, 113, 64–70. [Google Scholar] [CrossRef]
  75. Warneke, B.A.; Pister, K.S.J. An Ultra-Low Energy Microcontroller for Smart Dust Wireless Sensor Networks. In Proceedings of the Digest of Technical Papers—IEEE International Solid-State Circuits Conference, San Francisco, CA, USA, 15 February 2004; p. 47. [Google Scholar]
  76. Mokhloss, V.S.; Khadem, I. Dust Monitoring Systems. In Proceedings of the Sixth International Conference on Systems and Networks Communications, Barcelona, Spain, 23–28 October 2011. [Google Scholar]
  77. Nath, V.; Nath, A. Environment Monitoring Using Commercial Off-the-Shelf (COTS) Technologies. In Proceedings of the IFIP World Information Technology Forum, San José, Costa Rica, 12–14 September 2016; pp. 37–44. [Google Scholar]
  78. Chen, L.J.; Ho, Y.H.; Lee, H.C.; Wu, H.C.; Liu, H.M.; Hsieh, H.H.; Huang, Y.T.; Lung, S.C.C. An Open Framework for Participatory PM2.5 Monitoring in Smart Cities. IEEE Access 2017, 5, 14441–14454. [Google Scholar] [CrossRef]
  79. Gugliermetti, L.; Garcia, D.A. A cheap and third-age-friendly home device for monitoring indoor air quality. Int. J. Environ. Sci. Technol. 2018, 15, 185–198. [Google Scholar] [CrossRef]
  80. Tse, R.T.; Xiao, Y. A portable Wireless Sensor Network system for real-time environmental monitoring. In Proceedings of the17th International Symposium on a World of Wireless, Mobile and Multimedia Networks, WoWMoM 2016, Coimbra, Portugal, 21–24 June 2016. [Google Scholar]
  81. Westerdahl, D.; Fruin, S.; Sax, T.; Fine, P.M.; Sioutas, C. Mobile platform measurements of ultrafine particles and associated pollutant concentrations on freeways and residential streets in Los Angeles. Atmos. Environ. 2005, 39, 3597–3610. [Google Scholar] [CrossRef]
  82. Wang, M.; Zhu, T.; Zheng, J.; Zhang, R.Y.; Zhang, S.Q.; Xie, X.X.; Han, Y.Q.; Li, Y. Use of a mobile laboratory to evaluate changes in on-road air pollutants during the Beijing 2008 summer olympics. Atmos. Chem. Phys. 2009, 9, 8247–8263. [Google Scholar] [CrossRef] [Green Version]
  83. Padró-Martínez, L.T.; Patton, A.P.; Trull, J.B.; Zamore, W.; Brugge, D.; Durant, J.L. Mobile monitoring of particle number concentration and other traffic-related air pollutants in a near-highway neighborhood over the course of a year. Atmos. Environ. 2012, 61, 253–264. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  84. Levy, I.; Mihele, C.; Lu, G.; Narayan, J.; Hilker, N.; Brook, J.R. Elucidating multipollutant exposure across a complex metropolitan area by systematic deployment of a mobile laboratory. Atmos. Chem. Phys. 2014, 14, 7173–7193. [Google Scholar] [CrossRef] [Green Version]
  85. Shi, Y.; Lau, K.K.L.; Ng, E. Developing Street-Level PM 2.5 and PM 10 Land Use Regression Models in High-Density Hong Kong with Urban Morphological Factors. Environ. Sci. Technol. 2016, 50, 8178–8187. [Google Scholar] [CrossRef] [PubMed]
  86. Hankey, S.; Marshall, J.D. Land Use Regression Models of On-Road Particulate Air Pollution (Particle Number, Black Carbon, PM2.5, Particle Size) Using Mobile Monitoring. Environ. Sci. Technol. 2015, 49, 9194–9202. [Google Scholar] [CrossRef] [PubMed]
  87. Thai, A.; McKendry, I.; Brauer, M. Particulate matter exposure ong designated bicycle routes in Vancouver, British Columbia. Sci. Total Environ. 2008, 405, 26–35. [Google Scholar] [CrossRef] [PubMed]
  88. Dons, E.; Int Panis, L.; Van Poppel, M.; Theunis, J.; Willems, H.; Torfs, R.; Wets, G. Impact of time-activity patterns on personal exposure to black carbon. Atmos. Environ. 2011, 45, 3594–3602. [Google Scholar] [CrossRef]
  89. Song, C.; Qu, Z.; Blumm, N.; Barabási, A.L. Limits of predictability in human mobility. Science 2010, 327, 1018–1021. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  90. Canfield, M.A.; Ramadhani, T.A.; Langlois, P.H.; Waller, D.K. Residential mobility patterns and exposure misclassification in epidemiologic studies of birth defects. J. Expo. Sci. Environ. Epidemiol. 2006, 16, 538–543. [Google Scholar] [CrossRef] [PubMed]
  91. Brokamp, C.; Lemasters, G.K.; Ryan, P.H. Residential mobility impacts exposure assessment and community socioeconomic characteristics in longitudinal epidemiology studies. J. Expo. Sci. Environ. Epidemiol. 2016, 26, 428–434. [Google Scholar] [CrossRef] [Green Version]
  92. Ragettli, M.S.; Phuleria, H.C.; Tsai, M.Y.; Schindler, C.; de Nazelle, A.; Ducret-Stich, R.E.; Ineichen, A.; Perez, L.; Braun-Fahrländer, C.; Probst-Hensch, N.; et al. The relevance of commuter and work/school exposure in an epidemiological study on traffic-related air pollution. J. Expo. Sci. Environ. Epidemiol. 2015, 25, 474–481. [Google Scholar] [CrossRef] [PubMed]
  93. Wang, D.; Xiang, Z.; Fesenmaier, D.R. Smartphone Use in Everyday Life and Travel. J. Travel Res. 2016, 55, 52–63. [Google Scholar] [CrossRef]
  94. Ericsson. 5G Subscriptions to Reach Half a Billion in 2022: Ericsson Mobility Report. Press Release. 2016. Available online: https://www.ericsson.com/en/press-releases/2016/11/5g-subscriptions-to-reach-half-a-billion-in-2022-ericsson-mobility-report (accessed on 8 July 2019).
  95. Larkin, A.; Hystad, P. Towards Personal Exposures: How Technology Is Changing Air Pollution and Health Research. Curr. Environ. Health Rep. 2017, 4, 463–471. [Google Scholar] [CrossRef]
  96. Dewulf, B.; Neutens, T.; Lefebvre, W.; Seynaeve, G.; Vanpoucke, C.; Beckx, C.; Van de Weghe, N. Dynamic assessment of exposure to air pollution using mobile phone data. Int. J. Health Geogr. 2016, 15, 1–14. [Google Scholar] [CrossRef] [Green Version]
  97. Nyhan, M.; Grauwin, S.; Britter, R.; Misstear, B.; McNabola, A.; Laden, F.; Barrett, S.R.; Ratti, C. “Exposure Track”. The Impact of Mobile-Device-Based Mobility Patterns on Quantifying Population Exposure to Air Pollution. Environ. Sci. Technol. 2016, 50, 9671–9681. [Google Scholar] [CrossRef] [Green Version]
  98. Nyhan, M.M.; Kloog, I.; Britter, R.; Ratti, C.; Koutrakis, P. Quantifying population exposure to air pollution using individual mobility patterns inferred from mobile phone data. J. Expo. Sci. Environ. Epidemiol. 2019, 29, 238–247. [Google Scholar] [CrossRef]
  99. Steinle, S.; Reis, S.; Sabel, C.E. Quantifying human exposure to air pollution-Moving from static monitoring to spatio-temporally resolved personal exposure assessment. Sci. Total Environ. 2013, 443, 184–193. [Google Scholar] [CrossRef] [Green Version]
  100. Dias, D.; Tchepel, O. Modelling of human exposure to air pollution in the urban environment: A GPS-based approach. Environ. Sci. Pollut. Res. 2014, 21, 3558–3571. [Google Scholar] [CrossRef]
  101. Buonanno, G.; Stabile, L.; Morawska, L. Personal exposure to ultrafine particles: The influence of time-activity patterns. Sci. Total Environ. 2014, 468–469, 903–907. [Google Scholar] [CrossRef] [Green Version]
  102. Morabia, A.; Amstislavski, P.N.; Mirer, F.E.; Amstislavski, T.M.; Eisl, H.; Wolff, M.S.; Markowitz, S.B. Air Pollution and Activity During Transportation by Car, Subawy, and Walking. Am. J. Prev. Med. 2009, 37, 72–77. [Google Scholar] [CrossRef]
  103. Apparicio, P.; Apparicio, D.; Mathieu, M.-È. Turtle Sport: An Open-Source Software for Communicating with GPS Sport Watches. J. Open Res. Softw. 2018, 6, 25. [Google Scholar] [CrossRef] [Green Version]
  104. Apparicio, P.; Gelb, J.; Carrier, M.; Mathieu, M.È.; Kingham, S. Exposure to noise and air pollution by mode of transportation during rush hours in Montreal. J. Transp. Geogr. 2018, 70, 182–192. [Google Scholar] [CrossRef]
  105. Hasenfratz, D.; Saukh, O.; Sturzenegger, S.; Thiele, L. Participatory Air Pollution Monitoring Using Smartphones. Mob. Sens. 2012, 1, 1–5. [Google Scholar]
  106. Mendez, D.; Pérez, A.J.; Labrador, M.A.; Marron, J.J. P-Sense: A participatory sensing system for air pollution monitoring and control. In Proceedings of the 2011 IEEE International Conference on Pervasive Computing and Communications Workshops, PERCOM Workshops, Seattle, WA, USA, 21–25 March 2011; pp. 344–347. [Google Scholar]
  107. Brienza, S.; Galli, A.; Anastasi, G.; Bruschi, P. A low-cost sensing system for cooperative air quality monitoring in urban areas. Sensors 2015, 15, 12242–12259. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  108. Mendez, D.; Diaz, S.; Kraemer, R. Wireless technologies for pollution monitoring in large cities and rural areas. In Proceedings of the 24th Telecommunications Forum, TELFOR 2016, Belgrade, Serbia, 22–23 Novomber 2016. [Google Scholar]
  109. Hu, K.; Sivaraman, V.; Luxan, B.G.; Rahman, A. Design and Evaluation of a Metropolitan Air Pollution Sensing System. IEEE Sens. J. 2016, 16, 1448–1459. [Google Scholar] [CrossRef]
  110. De Nazelle, A.; Seto, E.; Donaire-Gonzalez, D.; Mendez, M.; Matamala, J.; Nieuwenhuijsen, M.J.; Jerrett, M. Improving estimates of air pollution exposure through ubiquitous sensing technologies. Environ. Pollut. 2013, 176, 92–99. [Google Scholar] [CrossRef] [Green Version]
  111. Krenn, P.J.; Titze, S.; Oja, P.; Jones, A.; Ogilvie, D. Use of global positioning systems to study physical activity and the environment: A systematic review. Am. J. Prev. Med. 2011, 41, 508–515. [Google Scholar] [CrossRef] [Green Version]
  112. Kerr, J.; Duncan, S.; Schipperjin, J. Using global positioning systems in health research: A practical approach to data collection and processing. Am. J. Prev. Med. 2011, 41, 532–540. [Google Scholar] [CrossRef] [PubMed]
  113. Feng, T.; Narayanan, S. Imputing Missing Data In Large-Scale Multivariate Biomedical Wearable Recordings Using Bidirectional Recurrent Neural Networks With Temporal Activation Regularization. In Proceedings of the 2019 41st Annual International Conference of the IEEE Engineering in Medicine and Biology Society (EMBC) 2019, Berlin, Germany, 23–27 July 2019; pp. 2529–2534. [Google Scholar]
  114. Mendez, D.; Labrador, M.; Ramachandran, K. Data interpolation for participatory sensing systems. Pervasive Mob. Comput. 2013, 9, 132–148. [Google Scholar] [CrossRef]
  115. Hao, Y.; Cheng, F.; Pham, M.; Rein, H.; Patel, D.; Fang, Y.; Feng, Y.; Yan, J.; Song, X.; Yan, H.; et al. A noninvasive, economical, instant-result method to diagnose and monitor type 2 diabetes using pulse wave: Case-Control study. J. Med. Internet Res. 2019, 7, e11959. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  116. Årsand, E.; Tatara, N.; Østengen, G.; Hartvigsen, G. Mobile phone-based self-management tools for type 2 diabetes: The few touch application. J. Diabetes Sci. Technol. 2010, 4, 328–336. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  117. Greenwood, D.A.; Blozis, S.A.; Young, H.M.; Nesbitt, T.S.; Quinn, C.C. Overcoming clinical inertia: A randomized clinical trial of a telehealth remote monitoring intervention using paired glucose testing in adults with type 2 diabetes. J. Med. Internet Res. 2015, 17, 1–16. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  118. Ding, H.; Karunanithi, M.; Kanagasingam, Y.; Vignarajan, J.; Moodley, Y. A pilot study of a mobile-phone-based home monitoring system to assist in remote interventions in cases of acute exacerbation of COPD. J. Telemed. Telecare 2014, 20, 128–134. [Google Scholar] [CrossRef]
  119. Bengtsson, U.; Kjellgren, K.; Hallberg, I.; Lindwall, M.; Taft, C. Improved Blood Pressure Control Using an Interactive Mobile Phone Support System. J. Clin. Hypertens. 2016, 18, 101–108. [Google Scholar] [CrossRef]
  120. Boriani, G.; Glotzer, T.V.; Ziegler, P.D.; De Melis, M.; Mangoni di S Stefano, L.; Sepsi, M.; Landolina, M.; Lunati, M.; Lewalter, T.; Camm, A.J. Detection of new atrial fibrillation in patients with cardiac implanted electronic devices and factors associated with transition to higher device-detected atrial fibrillation burden. Hear. Rhythm 2018, 15, 376–383. [Google Scholar] [CrossRef]
  121. Gorenek, B.; Bax, J.; Boriani, G.; Chen, S.A.; Dagres, N.; Glotzer, T.V.; Healey, J.S.; Israel, C.W.; Kudaiberdieva, G.; Levin, L.Å.; et al. Device-detected subclinical atrial tachyarrhythmias: Definition, implications and management—An European Heart Rhythm Association (EHRA) consensus document, endorsed by Heart Rhythm Society (HRS), Asia Pacific Heart Rhythm Society (APHRS) and Sociedad L. Europace 2017, 19, 1556–1578. [Google Scholar] [CrossRef]
  122. Wong, J.A.; Conen, D.; Van Gelder, I.C.; McIntyre, W.F.; Crijns, H.J.; Wang, J.; Gold, M.R.; Hohnloser, S.H.; Lau, C.P.; Capucci, A.; et al. Progression of Device-Detected Subclinical Atrial Fibrillation and the Risk of Heart Failure. J. Am. Coll. Cardiol. 2018, 71, 2603–2611. [Google Scholar] [CrossRef]
  123. Koshy, A.N.; Sajeev, J.K.; Nerlekar, N.; Brown, A.J.; Rajakariar, K.; Zureik, M.; Wong, M.C.; Roberts, L.; Street, M.; Cooke, J.; et al. Smart watches for heart rate assessment in atrial arrhythmias. Int. J. Cardiol. 2018, 266, 124–127. [Google Scholar] [CrossRef] [PubMed]
  124. Hochstadt, A.; Chorin, E.; Viskin, S.; Schwartz, A.L.; Lubman, N.; Rosso, R. Continuous heart rate monitoring for automatic detection of atrial fibrillation with novel bio-sensing technology. J. Electrocardiol. 2019, 52, 23–27. [Google Scholar] [CrossRef] [PubMed]
  125. Turakhia, M.P.; Desai, M.; Hedlin, H.; Rajmane, A.; Talati, N.; Ferris, T.; Desai, S.; Nag, D.; Patel, M.; Kowey, P.; et al. Rationale and design of a large-scale, app-based study to identify cardiac arrhythmias using a smartwatch: The Apple Heart Study. Am. Heart J. 2019, 207, 66–75. [Google Scholar] [CrossRef] [PubMed]
  126. Mortazavi, B.; Nemati, E.; VanderWall, K.; Flores-Rodriguez, H.G.; Cai, J.Y.; Lucier, J.; Naeim, A.; Sarrafzadeh, M. Can smartwatches replace smartphones for posture tracking? Sensors 2015, 15, 26783–26800. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  127. Bang, M.; Solnevik, K.; Eriksson, H. The Nurse Watch: Design and Evaluation of a Smart Watch Application with Vital Sign Monitoring and Checklist Reminders. In Proceedings of the AMIA Annual Symposium Proceedings 2015, San Francisco, CA, USA, 14–18 November 2015; Volume 2015, pp. 314–319. [Google Scholar]
  128. Rawassizadeh, R.; Tomitsch, M.; Nourizadeh, M.; Momeni, E.; Peery, A.; Ulanova, L.; Pazzani, M. Energy-efficient integration of continuous context sensing and prediction into smartwatches. Sensors 2015, 15, 22616–22645. [Google Scholar] [CrossRef] [Green Version]
  129. Banaee, H.; Ahmed, M.U.; Loutfi, A. Data mining for wearable sensors in health monitoring systems: A review of recent trends and challenges. Sensors 2013, 13, 17472–17500. [Google Scholar] [CrossRef] [Green Version]
  130. De Arriba-Pérez, F.; Caeiro-Rodríguez, M.; Santos-Gago, J.M. Collection and processing of data from wrist wearable devices in heterogeneous and multiple-user scenarios. Sensors 2016, 16, 1538. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  131. Ma, J.; Ovalle, A.; Woodbridge, D.M.K. Medhere: A Smartwatch-based Medication Adherence Monitoring System using Machine Learning and Distributed Computing. In Proceedings of the 2018 40th Annual International Conference of the IEEE Engineering in Medicine and Biology Society (EMBC), Honolulu, HI, USA, 17–21 July 2018; pp. 4945–4948. [Google Scholar]
  132. Reeder, B.; David, A. Health at hand: A systematic review of smart watch uses for health and wellness. J. Biomed. Inf. 2016, 63, 269–276. [Google Scholar] [CrossRef]
  133. Apiletti, D.; Baralis, E.; Bruno, G.; Cerquitelli, T. Real-time analysis of physiological data to support medical applications. IEEE Trans. Inf. Technol. Biomed. 2009, 13, 313–321. [Google Scholar] [CrossRef]
  134. Haescher, M.; Matthies, D.J.; Krause, S.; Bieber, G. Presenting a Data Imputation Concept to Support the Continuous Assessment of Human Vital Data and Activities. In Proceedings of the 12th ACM International Conference on PErvasive Technologies Related to Assistive Environments 2019, Island of Rhodes, Greece, 5–7 June 2019; pp. 587–592. [Google Scholar]
  135. Schulte, P.F. Molecular Epidemiology: Principles and Practice; Academic Press: New York, NY, USA, 1993. [Google Scholar]
  136. Crinnion, W.J. The CDC fourth national report on human exposure to environmental chemicals: What it tells us about our toxic burden and how it assists environmental medicine physicians. Altern. Medi. Rev. 2010, 15, 101–108. [Google Scholar]
  137. Angerer, J.; Gündel, J. Biomonitoring and occupational medicine. Possibilities and limitations. Annali dell’Istituto Superiore di Sanita 1996, 32, 199–206. [Google Scholar] [PubMed]
  138. Rüdiger, H.W. Biomonitoring in Occupational Medicine. In Toxicology; Elsevier: Amsterdam, The Netherlands, 1999; pp. 1027–1040. [Google Scholar]
  139. Bartolucci, G.B.; de Rosa, E.; Gori, G.P.; Corona, P.C.; Perbellini, L.; Brugnone, F. Biomonitoring of occupational exposure to styrene. Appl. Ind. Hyg. 1986, 1, 125–131. [Google Scholar] [CrossRef]
  140. Haines, D.A.; Saravanabhavan, G.; Werry, K.; Khoury, C. An overview of human biomonitoring of environmental chemicals in the Canadian Health Measures Survey: 2007–2019. Int. J. Hyg. Environ. Health 2017, 220, 13–28. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  141. Centers for Disease Control and Prevention. Fourth National Report on Human Exposure to Environmental Chemicals; updated tables; Department of Health and Human Services: Atlanta, GA, USA, 2012. [Google Scholar]
  142. Hajat, A.; Allison, M.; Diez-Roux, A.V.; Jenny, N.S.; Jorgensen, N.W.; Szpiro, A.A.; Vedal, S.; Kaufman, J.D. Long-term exposure to air pollution and markers of inflammation, coagulation, and endothelial activation a repeat-measures analysis in the multi-ethnic study of atherosclerosis (MESA). Epidemiology 2015, 26, 310–320. [Google Scholar] [CrossRef]
  143. Ernst, E. The role of fibrinogen as a cardiovascular risk factor. Atherosclerosis 1993, 100, 1–12. [Google Scholar] [CrossRef]
  144. Abou-Raya, A.; Abou-Raya, S. Inflammation: A pivotal link between autoimmune diseases and atherosclerosis. Autoimmun. Rev. 2006, 5, 331–337. [Google Scholar] [CrossRef]
  145. Hwang, S.J.; Ballantyne, C.M.; Sharrett, A.R.; Smith, L.C.; Davis, C.E.; Gotto, A.M.J.; Boerwinkle, E. Circulating adhesion molecules VCAM-1, ICAM-1, and E-selectin in carotid atherosclerosis and incident coronary heart disease cases: The Atherosclerosis Risk In Communities (ARIC) study. Circulation 1997, 96, 4219–4225. [Google Scholar] [CrossRef]
  146. Galea, S.; Tracy, M. Participation Rates in Epidemiologic Studies. Ann. Epidemiol. 2007, 17, 643–653. [Google Scholar] [CrossRef]
  147. World Health Organization. Human Biomonitoring: Facts and Figures; Regional Office for Europe: Copenhagen, Denmark, 2015. [Google Scholar]
  148. Pedersen, O.B.; Erikstrup, C.; Kotzé, S.R.; Sørensen, E.; Petersen, M.S.; Grau, K.; Ullum, H. The Danish Blood Donor Study: A large, prospective cohort and biobank for medical research. Vox Sanguinis 2012, 102, 271. [Google Scholar] [CrossRef]
Figure 1. Exposure assessment challenges and their novel solutions.
Figure 1. Exposure assessment challenges and their novel solutions.
Atmosphere 11 00122 g001
Figure 2. Outcome assessment challenges and their novel solutions.
Figure 2. Outcome assessment challenges and their novel solutions.
Atmosphere 11 00122 g002

Share and Cite

MDPI and ACS Style

Yarza, S.; Hassan, L.; Shtein, A.; Lesser, D.; Novack, L.; Katra, I.; Kloog, I.; Novack, V. Novel Approaches to Air Pollution Exposure and Clinical Outcomes Assessment in Environmental Health Studies. Atmosphere 2020, 11, 122. https://doi.org/10.3390/atmos11020122

AMA Style

Yarza S, Hassan L, Shtein A, Lesser D, Novack L, Katra I, Kloog I, Novack V. Novel Approaches to Air Pollution Exposure and Clinical Outcomes Assessment in Environmental Health Studies. Atmosphere. 2020; 11(2):122. https://doi.org/10.3390/atmos11020122

Chicago/Turabian Style

Yarza, Shaked, Lior Hassan, Alexandra Shtein, Dan Lesser, Lena Novack, Itzhak Katra, Itai Kloog, and Victor Novack. 2020. "Novel Approaches to Air Pollution Exposure and Clinical Outcomes Assessment in Environmental Health Studies" Atmosphere 11, no. 2: 122. https://doi.org/10.3390/atmos11020122

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop