Search Results (12)

Cotton is a preferred textile fiber for apparel textiles and is used primarily for summer wear. However, cotton has drawbacks, such as poor wrinkle resistance, and therefore, blends of cotton with other fibers have gained acceptance in the industry. In this study, a novel 90:10 cotton–cork blended fabric was studied for its physical and performance properties and benchmarked against a 100% cotton fabric. Fabric samples were analyzed to determine the wrinkle recovery angle, tenacity, abrasion resistance, shrinkage, CLO value, moisture absorption, and dyeability. The samples were further analyzed using SEM, DSC, and FTIR. The results showed significant differences between the two fabrics. Cotton–cork blended textile fabric had higher performance properties with the potential to be a viable, sustainable apparel textile. Full article

The vinyl phytic acid (GPA) was prepared using biophytic acid (PA) and glycidyl methacrylate (GMA), in which double bonds were introduced into the phytic acid molecule to increase the active groups in the phytic acid molecule. Furthermore, itaconic acid (IA) containing two unsaturated double bonds and GPA was polymerized in situ and crosslinked on the surface of cotton fabrics, and flame retardant and crease-proofed fabrics were obtained. The effects of GPA, IA, and the initiator on the flame-retardant and crease-proofing properties of the fabrics were analyzed by a single-factor and double-dip double-nip experiment. A flame-retardant and wrinkle-resistant fabric was obtained when the limiting oxygen index (LOI) and wrinkle recovery angle (WRA) were 28% and 270°, respectively. During combustion, the thermal properties of the fabrics changed; typically, the extrapolated initial temperature (Te) decreased, and moisture release increased. After burning, the fabrics had good shape retention, and the carbon residue content increased to 48%, which effectively inhibited or slowed down the combustion and heat release of the textiles. However, the whiteness, mechanical properties, and washability of the products need to be further improved. Full article

Silk, a natural protein fiber, is widely used in the textile industry and biomedical materials for its excellent properties. However, its application in some fields is seriously restricted due to its poor anti-wrinkle behavior. In this study, 2,4,6-trichloropyrimidine (TLP) was used in the production of anti-wrinkle silk fabrics. The optimum finishing conditions were as follows: 3-g/L 2,4,6-trichloropyrimidine, 6-g/L NaHCO₃, 8-g/L Na₂SO₄, finishing temperature of 65 °C, and finishing time of 40 min. The crease recovery angle of the finished fabric is 16–20% higher than the unfinished fabric, and the finishing process has a small effect on the whiteness of silk while achieving some degree of washing resistance. The morphology and chemical structures of the finished silk fabric were characterized by scanning electron microscopy and Fourier transform infrared spectroscopy. The K/S value of the finished silk fabric dyed with reactive dyes increased compared with the silk fabric only dyed, indicating that the dyeability of the finished fabric was improved. This technology provides a new method for fabricating silk color crease-resistant fabrics. Full article

The single light oil regenerating agent has certain limitations on the performance recovery of aged asphalt. In this study, tung oil, dioctyl phthalate (DOP), C9 petroleum resin, and organic montmorillonite (OMMT) were used to prepare the composite regenerating agent, and its optimal mix proportion was determined by the orthogonal experimental design. The rheological properties and anti-aging performance of reclaimed asphalt were studied by the dynamic shear rheometer (DSR) and bending beam rheometer (BBR); and the Fourier transform infrared (FTIR) spectrometer, gel permeation chromatography (GPC), and scanning electron microscope (SEM) were adopted to explore its microstructure, morphology, and mechanism of action. The results show that with the addition of tung oil composite regenerating agent, the rheological properties of aged asphalt can be effectively recovered, even better than that of base asphalt. By using the complex modulus aging index (CMAI) and phase angle aging index (PMAI) it is found that the anti-aging performance of reclaimed asphalt is better than that of base asphalt. With the optimal content of the tung oil composite regenerating agent, the contents of characteristic functional groups and macromolecular asphaltenes in the aged asphalt can be reduced, indicating that the composite regenerating agent is beneficial to the dispersion and dissolution of polar substances in the aged asphalt. After aging, a large number of wrinkles appear on the surface of the asphalt. However, the addition of the tung oil composite regenerating agent can make the asphalt surface smooth, which indicates that the tung oil composite regenerating agent can restore the microstructure and morphology of aged asphalt to a certain extent. Full article

To break the trade-off effect between permeability and selectivity in separation, wrinkled carbon nanotubes@polylactic acid (CNTs@PLLA) composite membranes were successfully fabricated in this work. On pre-deformed PLLA membranes, CNTs were loaded by filtrating their suspension, followed by releasing the PLLA upon heating based on its shape memory effect. The asynchronous deformations of CNTs and PLLA layers produced wrinkled CNTs@PLLA composite membranes. Relative to the reference without wrinkles, the attained wrinkled composite membranes exhibit much higher flux (~12 times) without any loss of rejection ratio during the separation of water-in-hexadecane emulsion. The significant improvement of separation performance can be attributed to the following issues: Firstly, the existence of wrinkles results in higher surface roughness, providing an additional driving force for separation resulting from the enlarged contact-angle difference between water and oil; Secondly, the shrinkage of the supporting PLLA layer during recovery induces the preferred alignment of CNTs along the wrinkle direction, which is the reason for the orientated slit pores with enhanced overlap of neighboring pores in the film-thickness direction; Finally, a wrinkled surface significantly increases the available area for separation. The synergism of the effects discussed above contributes to much higher permeability and comparable selectivity relative to the reference. Full article

In this paper, we explore the self-cleaning and washing durability of green-prepared ZnO NPs combined with cotton fabrics. Honeysuckle extract was used to prepare ZnO NPs with an average particle size of 15.3 nm. Cotton fabrics were then treated with oxalic acid (OA), tartaric acid (TA), and succinic acid (SA) as cross-linking agents, sodium hypophosphite as a catalyst, and after that, the ZnO NPs were applied to the cross-linked cotton fabrics by the padding to prepare the self-cleaning cotton fabrics. The morphology and structure of the fabric samples were characterized using FTIR, scanning electron microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDS), and XRD. The optical properties of the cotton fabric samples were discussed by UV-vis diffuse reflectance spectrum, and the self-cleaning performance, wrinkle recovery angle and ultraviolet protection performance of the cotton fabric samples were analyzed. The results showed that the carboxyl groups of TA, OA, and SA were esterified with hydroxyl groups of the cotton fiber and formed a film on the surface of the cotton fabrics. ZnO NPs were successfully loaded onto the cotton fabrics by strong electrostatic interaction, causing the improvement of the washing resistance of the cross-linked fabrics. In addition, compared with uncross-linked fabrics, the wrinkle recovery performance of the cross-linked fabrics had also been greatly improved, and the UV protection factor reached 50+, thus obtaining an excellent self-cleaning, multifunctional cotton-based textile with anti-wrinkle and anti-ultraviolet properties. Full article

Cotton fabrics were dyed with the madder and compounds of citric acid (CA) and dicarboxylic acids [tartaric acid (TTA), malic acid (MLA), succinic acid (SUA)] as cross-linking agents and sodium hypophosphite (SHP) as the catalyst. The molecular structures and crystal structures of the dyed cotton fabrics were analyzed using Fourier-transform infrared spectroscopy (FTIR) and X-ray diffractometry (XRD), respectively. The results showed that the polycarboxylic acids esterified with the hydroxyl groups in the dye and cellulose, respectively, and the reaction mainly occurred in the amorphous region of the cotton fabric. Compared with the direct dyed cotton fabric, the surface color depth (K/S) values of the CA, CA+TTA, CA+MLA, CA+SUA cross-linked dyed cotton fabrics increased by approximately 160%, 190%, 240%, 270%, respectively. The CA+SUA cross-linked dyed cotton fabric achieved the biggest K/S value due to the elimination of the negative effect by α-hydroxyl in TTA and MLA on esterification reaction, and the cross-linked dyed cotton fabrics had great levelness property. The washing and rubbing fastness of the cross-linked cotton fabrics were above four levels. The light resistance stability and the antibacterial property of the cross-linked dyed cotton fabrics was obviously improved. The sum of warp and weft wrinkle recovery angle (WRA) of the CA+SUA cross-linked dyed cotton fabric was 55° higher than that of raw cotton fabric, and its average UV transmittance for UVA was less than 5% and its UPF value was 50+, showing a great anti-wrinkle and anti-ultraviolet properties. Full article

In the anti-wrinkle finishing of cotton fabrics, the decreased dyeability of the finished fabrics has always been a difficult problem. A new anti-wrinkle finishing mode was developed to solve this problem by changing the finishing sequence of fabric dyeing and anti-wrinkle. In this research, the partial oxidization of raffinose with sodium periodate generated multiple aldehydes, which acted as multifunctional cross-linkers and endowed cotton fabrics with anti-wrinkle and hydrophilic properties. The structural characteristics of oxyRa were analyzed by FTIR and ¹³C-NMR. Through response surface methodology (RSM), the finishing model of oxyRa was established from the influencing factors of catalyst concentration, pH, curing temperature and time, and the optimized finishing process: the catalyst concentration was 20.12 g/L, pH was 4.32, curing temperature was 150 °C and curing time was 120 s. Under this condition, the predicted wrinkle recovery angle (WRA) of the finished fabric was up to 249.76°, Tensile strength (TS) was 75.62%, Whiteness index (WI) was 70.69. Importantly, comparing the anti-wrinkle and dyeing performance of the fabric with anti-wrinkle and then dyeing and anti-wrinkle after dyeing, the oxyRa-treated fabrics showed better dyeing properties compared with previously reported dimethyldihydroxyethylene urea (DMDHEU), glutaraldehyde (GA), and 1,2,3,4-butanetetracarboxylic acid (BTCA). Analysis of the combined mechanism of different finishing agents and cellulose, demonstrated the reason why oxyRa can be used to change the order of dyeing and anti-wrinkle finishing. Full article

In anti-wrinkle finishing, the crosslinking degree of fabric is mainly determined by wrinkle recovery angle, stiffness, and viscosity, these indicators can only reflect the finishing effect from a macro perspective, which cannot reflect whether the crosslinking is sufficient, and it is difficult to quantify the crosslinking degree. In this paper, we combined the Kjeldahl method with the Arrhenius formula and proposed a method to analyze the crosslinking degree of dimethyloldihydroxyethyleneurea (two-dimensional (2D) resin) with cotton cellulose during delayed-cure finishing for the first time. The nitrogen content of completed fabrics during storage was measured by the Kjeldahl method, and the reaction rate equation of the 2D resin and cellulose under normal temperature conditions was calculated. The results show that the nitrogen content is more suitable to indicate the crosslinking degree, and the apparent activation energy was 28.271 kJ/mol and the pre-finger factor was 0.622, which indicated that the 2D resin was prone to cross-linking with cotton fabrics during storage. During long-term storage, the relative errors between the calculated and measured values of the nitrogen content were within ±5%, and the accuracy was higher than the traditional evaluation method. The stability of 2D resins during the storage of delayed-curing finishing was also analyzed through this method. Full article

To explore the combination of silver nanoparticles (Ag NPs) prepared in a green manner with cotton fabrics and the washing durability of the fabric after the combination. In this paper, the natural material, honeysuckle extract, was used as a reducing agent to prepare the Ag NPs’ solution. The structure and size of Ag NPs were analyzed using ultraviolet–visible spectrophotometry (UV–vis), transmission electron microscopy (TEM), dynamic light scattering (DLS), X-ray powder diffraction (XRD), and Fourier transform infrared (FT-IR) spectroscopy characterization. The results showed that Ag⁺ was successfully reduced to Ag⁰ by the honeysuckle extract, the particle size was about 10.59 nm, and the potential was −42.9 mV, so it had strong electrostatic repulsion and good stability. Meanwhile, it was found that the synthesized Ag NPs were well coated by the honeysuckle extract, so they would not aggregate. Then, the cotton fabric was finished with Ag NPs’ solution by the dipping method using a complex of polymaleic acid (PMA) and citric acid (CA) as a cross-linking agent to fix Ag NPs on the cotton fabric. The structures of cotton fabrics before and after finishing were characterized using FT-IR, scanning electron microscopy (SEM), XRD, X-ray photoelectron spectroscopy (XPS), and thermogravimetric (TG) analysis, and the multifunctional properties of the finished cotton fabrics were explored by measuring the antibacterial rate, the wrinkle recovery angle (WRA), and the UV protection factor (UPF) value. The results show that Ag NPs were successfully loaded onto cotton fabric, and the PMA + CA compound was successfully cross-linked to the fabric. The cross-linked Ag NPs’ cotton fiber was rougher than that before cross-linking, and its TG stability improved. The PMA + CA compound fixed Ag NPs on the cotton fabric through chemical bonds, so it still had a 99% antibacterial effect against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) after 50 washings. Compared with unfinished cotton fabric, the UPF value and WRA of the cross-linked Ag NPs cotton increased by 34.09 and 98°, respectively, and its color did not change much. Full article

Multifunctionalization of cotton using a single product has not been made until now. Such a product was synthesized using compounds with multiple functions (glyoxal, ethylenediamine (ED) and monochlorotriazinyl-β–cyclodextrin (MCT-β-CD)), under different mass ratios. Obtaining this multifunctional derivative has been confirmed by spectroscopic analyses (¹H-NMR and FTIR) and a scanning electron microscope (SEM). Treatment of cotton with the MCT-β-CD derivative (D-CD) has been realized with the pad dry-cure technology. The presence of this multifunctional derivative on cotton was highlighted with spectroscopic (FTIR, EDAX, XRD) and thermoanalytical (DSC) methods. The objective of treating cotton with D-CD was to achieve four simultaneous effects: large wrinkle recovery angle (WRA), hydrophilicity, antibacterial capacity and a good breaking resistance. This objective has been achieved, so the garments that will be manufactured with such multifunctional cotton will be more comfortable. The efficiency of treatments with D-CD was marked out by multiple linear regression (MLR) and certain quality indices. Using MLR, the behavior of the treated cotton was mathematically modeled and the stationary/optimal points corresponding to each effect were calculated. Quality indices have been calculated and all final samples had values higher than 1, which confirmed the positive effects exerted by D-CDs on cotton. Full article

In this article, we report a simple approach to generate micropillars (whose top portions are covered by sub-micron wrinkles) on the inner surfaces of polystyrene (PS) microchannels, as well as on the top surface of the PS substrate, based on strain-recovery deformations of the PS and oxygen reactive ion etch (ORIE). Using this approach, two types of micropillar-covered microchannels are fabricated. Their widths range from 118 μm to 132 μm, depths vary from 40 μm to 44 μm, and the inclined angles of their sidewalls are from 53° to 64°. The micropillars enable these microchannels to have super-hydrophobic properties. The contact angles observed on the channel-structured surfaces are above 162°, and the tilt angles to make water drops roll off from these channel-structured substrates can be as small as 1°. Full article