Search Results (29)

Surface functionalization is a key enabler that imparts solid materials with excellent chemoselectivity. With this aim, halloysite and sepiolite clay particles were functionalized with carboxyethylsilanetriol sodium salt (CES) and 3-aminopropyltriethoxysilane (APTES), affording carboxy-terminated and amino-terminated clay, respectively. In the case of halloysite, the grafting occurs at Al-OH groups of the lumen surface (tube inner surface) and Al-OH and Si-OH groups at the edges and external surface defects of the nanotubes. For sepiolite, silanol groups located on the edges of the structural channels were at the origin of a chemical reaction between this fibrous clay and the terminal alkoxysilane. The resulting modified clays were examined for removal of Congo red (CR) and malachite green (MG) as anionic and cationic dyes, respectively. Clay bearing only carboxylic groups display more affinity towards cationic dye (MG), recording 926 mg·g⁻¹ and 387 mg·g⁻¹ for HNT-CES and SEP-CES, respectively, while amino-functionalized clays show very high adsorption for anionic dye (CR), reaching 1232 and 1228 mg·g⁻¹ for HNT-APTES and SEP-APTES, respectively. Simultaneous grafting of the two silyl coupling reagents was also attempted through one-pot and sequential grafting method, with the latter being more appropriate to access amphoteric clay featuring both carboxylic and amino groups. The behavior of the bifunctional adsorbents was investigated with respect to pristine and monofunctional clay. The obtained results provide insights to fulfill the requirement for handling complex water effluent containing both anionic and cationic pollutants, towards more sustainable development. Full article

Renal function refers to the combined actions of the glomerulus and tubular system to achieve homeostasis in bodily fluids. While the glomerulus is essential in the first step of urine formation through a coordinated filtration mechanism, the tubular system carries out active mechanisms of secretion and reabsorption of solutes and proteins using specific transporters in the epithelial cells. The assessment of renal function usually focuses on glomerular function, so the tubular function is often underestimated as a fundamental part of daily clinical practice. Therefore, it is essential to properly understand the tubular physiological mechanisms and their clinical association with prevalent human pathologies. This review discusses the primary solutes handled by the kidneys, including glucose, amino acids, sodium, potassium, calcium, phosphate, citrate, magnesium and uric acid. Additionally, it emphasizes the significance of physicochemical characteristics of urine, such as pH and osmolarity. The use of a concise methodology for the comprehensive assessment of urine should be strengthened in the basic training of nephrologists when dealing with problems such as water and electrolyte balance disorders, acid-base disorders, and harmful effects of commonly used drugs such as chemotherapy, antibiotics, or diuretics to avoid isolated replacement of the solute without carrying out comprehensive approaches, which can lead to potentially severe complications. Full article

Water regeneration in PVC production is a key issue to consider, given the high freshwater consumption rate of the process. This research evaluates the inherent safety of poly(vinyl chloride) (PVC) production via suspension polymerization by implementing mass and energy integration strategies in combination with wastewater regeneration under a zero-liquid-discharge (ZLD) approach. The impact of these integrations on process safety was examined by considering the risks associated with the handling of hazardous materials and critical operations, as well as the reduction in waste generation. To this end, the Inherent Safety Index (ISI) methodology was employed, which quantifies hazards based on factors such as toxicity and flammability, enabling the identification of risks arising from system condition changes due to the implementation of sustainable water treatment technologies. Although the ISI methodology has been applied to various chemical processes, there are few documented cases of its specific application in PVC plants that adopt circular production strategies and water resource sustainability. Therefore, in this study, ISI was used to thoroughly evaluate each stage of the process, providing a comprehensive picture of the safety risks associated with the use of sustainable technologies. The assessment was carried out using simulation software, computer-aided process engineering (CAPE) methodologies, and information obtained from safety repositories and expert publications. Specifically, the Chemical Safety Index score was 22 points, with the highest risk associated with flammability, which scored 4 points, followed by toxicity (5 points), explosiveness (2 points), and chemical interactions, with 4 points attributed to vinyl chloride monomer (VCM). In the toxicity sub-index, both VCM and PVC received 5 points, while substances such as sodium hydroxide (NaOH) and sodium chloride (NaCl) scored 4 points. In the heat of reaction sub-index, the main reaction scored 3 points due to its high heat of reaction (−1600 kJ/kg), while the secondary reactions from PVA biodegradation scored 0 points for the anoxic reaction (−156.5 kJ/kg) and 3 points for the aerobic reaction (−2304 kJ/kg), significantly increasing the total index. The Process Safety Index scored 15 points, with the highest risk found in the inventory of hazardous substances within the inside battery limits (ISBL) of the plant, where a flow rate of 3241.75 t/h was reported (5 points). The safe equipment sub-index received 4 points due to the presence of boilers, burners, compressors, and reactors. The process structure scored 3 points, temperature 2, and pressure 1, reflecting the criticality of certain operating conditions. Despite sustainability improvements, the process still presented significant chemical and operational risks. However, the implementation of control strategies and safety measures could optimize the process, balancing sustainability and safety without compromising system viability. Full article

Background: Abnormal sodium-dependent hexose reabsorption in the proximal tubule, accompanied by a functional decrease in sodium and water reabsorption under conditions of increased volemia, may be attributed to a dysfunction of primary transporters related to a genetic defect in the Na,K-ATPase gamma subunit. Methods: We examined two sisters, aged 6 and 8 years, who presented with hypercalciuria, glucosuria, fructosuria, galactosuria, and atypical proteinuria. Primary diabetes, galactosemia, and fructosemia were excluded, suggesting a defect in cellular hexose transport in the proximal tubule. We conducted tests on the family members to assess the impact of gradually increasing volemia, using a water-loading test, on tubular H⁺ transport and urinary excretion of calcium, citrate, endothelin-1 (ET-1), and atypical proteins. Whole-exome sequencing was performed in the affected patients to identify the genetic basis of this phenotype. Results: Extended investigations revealed a complex defect in tubular H⁺ transport, calcium and citrate handling, and atypical proteinuria, resulting from water load-driven overproduction of endothelin-1 (ET-1). Genetic analysis identified a heterozygous pathogenic variant, c.80G>A, p.(Arg27His), in the FXYD2 gene, which encodes the gamma subunit of sodium/potassium-transporting ATPase. Conclusions: Our findings provide evidence that a defect in FXYD2 (splice form a) leads to functional impairment of proximal tubular hexose reabsorption. This is the first report on the metabolic consequences of a pathogenic FXYD2 variant affecting the gamma subunit of sodium/potassium-transporting ATPase in humans. The genotype–phenotype correlation in two siblings with a sodium-dependent defect in fructose, galactose, and glucose renal reabsorption allowed us to characterize a disease with a distinct clinical course and biochemical profile, not previously reported in the medical literature or genetic databases. Analysis of this condition was crucial for the early introduction of reno-protective treatment aimed at slowing the progression of nephropathy and for risk assessment in family members, which was essential for genetic counseling. Full article

Alternative means of control are becoming increasingly relevant to the improvement of safety and the reduction of postharvest losses and waste of fruit and vegetables, especially in view of the application of the EU Greed Deal. A previous study from our research group that focused on the electrolysis process of water and was conducted using NaCl and NaHCO₃ as electrolytes proved to efficiently reduce pathogen inoculum in packinghouse washing water. In the present study, we examined the effect of the electrolyzed salt solutions (eNaCl and eNaHCO₃) produced in the same experimental conditions previously reported to be used as postharvest treatments during handling and commercialization, and/or at the consumer’s site. We tested the electrolyzed solutions, obtained in the presence or absence of the salts, against five relevant fungal pathogens in terms of conidia viability, and on various hosts in terms of rot incidence/severity. Chemical parameters of electrolyzed and non-electrolyzed solutions were also assessed. Although a different susceptibility to treatments was observed among pathogens, electrolyzed sodium chloride (eNaCl) was the most efficient treatment for preventing spore germination, as well as for minimizing fruit rot. However, a consistent control of fungal viability and consequent rot was also achieved using electrolyzed tap water (eW). The eNaHCO_3, although less efficient on fungal viability, provided a significant effect against fruit rot. The investigated electrolyzed solutions seem promising for reducing the waste of fresh fruit and vegetables. Full article

Ink-jet-printed silk, a premium textile material, was achieved by utilizing a bio-based gardenia blue dye. However, the sharpness of the printing pattern is difficult to control due to the limited water-retention capacity of silk. To address this issue, three polysaccharide derivatives, namely, sodium alginate (SA), low-viscosity hydroxypropyl methyl cellulose (HPMC-I), and high-viscosity hydroxypropyl methyl cellulose (HPMC-II), were employed as thickeners to modify the silk by the dipping–padding method. Firstly, the preparation of the gardenia blue ink and the rheology assessment of the thickener solution were conducted. Furthermore, the impacts of different thickeners on the micro-morphology, element composition, and hydrophilicity of the silk, along with the wetting behavior of the ink on the silk, were analyzed comparatively in order to identify an appropriate thickener for preserving pattern outlines. Lastly, the color features, color fastness, and wearing characteristics of the printed silk were discussed to evaluate the overall printing quality. Research results showed that the optimized ink formulation, comprising 12% gardenia blue, 21% alcohols, and 5.5% surfactant, met the requirements for ink-jet printing (with a viscosity of 4.48 mPa·s, a surface tension of 34.12 mN/m, and a particle size of 153 nm). The HPMC-II solution exhibited prominent shear-thinning behavior, high elasticity, and thixotropy, facilitating the achievement of an even modification effect. The treatment of the silk with HPMC-II resulted in the most notable decrease in hydrophilicity. This can be attributed to the presence of filled gaps and a dense film on the fibers’ surface after the HPMC-II treatment, as observed by scanning electron microscopy. Additionally, X-ray photoelectron spectroscopy analysis confirmed that the HPMC-II treatment introduced the highest content of hydrophobic groups on the fiber surface. The reduced hydrophilicity inhibited the excessive diffusion and penetration of gardenia blue ink, contributing to a distinct printing image and enhanced apparent color depth. Moreover, the printed silk demonstrated qualified color fastness to rubbing and soaping (exceeding grade four), a soft handle feeling, an ignorable strength loss (below 5%), and a favorable air/moisture penetrability. In general, the surface modification with the HPMC-II treatment has been proven as an effective strategy for upgrading the image quality of bio-based dye-printed silk. Full article

With the advent of the COVID-19 pandemic, the global consumption of single-use surgical masks has risen immensely, and it is expected to grow in the coming years. Simultaneously, the disposal of surgical masks in the environment has caused plastic pollution, and therefore, it is exigent to find innovative ways to handle this problem. In this study, surgical masks were processed in a laboratory using the mechanical grinding method to obtain recycled surgical masks (RSM). The RSM was added in doses of 0%, 1%, 2%, 3%, and 4% by volume of geopolymer bricks, which were synthesized with ground granulated blast furnace slag (GGBS), rice husk ash (RHA), sand, and sodium silicate (Na₂SiO₃) at ambient conditions for a duration of 28 days. The developed bricks were tested for compressive strength, flexural strength, density, water absorption, efflorescence, and drying shrinkage. The results of the study reveal that compressive strength and flexural strength improved with the inclusion of RSM in the bricks. The highest values of compressive strength and flexural strength were 5.97 MPa and 1.62 MPa for bricks with 4% RSM, respectively. Further, a reduction in the self-weight of the bricks was noticed with an increase in RSM. There was no pronounced effect of RSM on the water absorption and efflorescence properties. However, the RSM played a role in reducing the drying shrinkage of the bricks. The sustainability analysis divulges the catalytic role of RSM in improving material performance, thereby proving to be a potential candidate for low-carbon material in the construction industry. Full article

Hypertension is an important morbidity factor. The prognostic consequences of the white-coat effect have been studied extensively. The repercussion on the circadian rhythm of urinary water and salt excretion in the same subgroup remain, conversely, among the open topics. Postulating an impaired diurnal sodium and volume excretion we decided to investigate both, in subjects with or without a white-coat effect, in the general population. A sample of 1023 subjects, has been considered. We collected 24-h urine samples, divided in day and night, and we measured the blood pressure with an Ambulatory Blood Pressure Monitoring (ABPM). ABPM values were then compared with physician collected in-office values to assign subjects to the group with or without the white-coat effect. Concerning the circadian pattern of urinary sodium excretion, we found no significant differences between the groups. There was instead in the white-coat effect group a higher night/day ratio of urinary water excretion. The white-coat effect, has been considered a potential hypertension precursor, and its consequent handling could be prospectively relevant in hypertension prevention. The absence of repercussions on the urinary circadian sodium excretion pattern and on the potentially related risk factors in subjects with a white coat effect is reassuring. The clinical significance of the impact on the night/day ratio of water excretion needs to be further investigated. Full article

Water is a resource that is essential to almost all phases of industrial and manufacturing operations globally. It is important to handle the wastewater generated professionally. The textile industry is one of the major global polluters, with textile producers responsible for one-fifth of all industrial water pollution worldwide. In contrast, heavy metal contamination has developed into a critical, expanding global environmental problem. Geopolymer is a cementitious constituent of amorphous aluminosilicates derived from natural or industrial wastes. It is produced using the polymerization of aluminosilicate raw ingredients in an alkaline atmosphere. The aim of this study is to evaluate the application of eco-friendly geopolymer cement in the immobilization technique for the treatment of wastewater including heavy metals and dyes. Geopolymer cement pastes were organized using slag and fly ash as an aluminosilicate source, (1:1) sodium silicate and sodium hydroxide 15 wt.% as an alkali activator in the presence of organic dye pollutant reactive red 195, and Cu²⁺ ions (700 ppm) at different hydration times for up to 28 days. The physicochemical and mechanical properties of the prepared geopolymer cement mixes were further examined in relation to reactive dye pollutant and Cu²⁺ ions. The hydration characteristic was examined using the compressive strength and % of total porosity tests, as well as FTIR and XRD studies. Our findings support the 100% immobilization of both Cu²⁺ ions and organic dye pollutants in prepared geopolymer pastes for up to 28 days of hydration. Additionally, adding both Cu²⁺ ions and dye pollutants to the prepared geopolymer paste improves its mechanical properties, which is also supported by FTIR data. XRD and FTIR studies showed that the Cu²⁺ ions and dying bath effluent addition have no influence on the kind of hydration products that are produced. On the other hand, the geopolymerization process is negatively impacted by the presence of Cu²⁺ ions alone in the geopolymer paste. Full article

Chronic wound treatment accounts for a substantial percentage of the medical expenses worldwide. Improving and developing novel wound care systems can potentially help to handle this problem. Wound dressings loaded with antiseptics may be an important tool for wound care, as they inhibit bacterial growth at the wound site. The goal of the present work was to investigate the potential of using casein hydrogel dressings loaded with two antiseptic drugs, Octiset^® or polyhexanide, to treat chronic wounds. Casein-based hydrogels are inexpensive and have several properties that make them suitable for biomedical applications. Two types of casein were used: casein sodium salt and acid casein, with the formulations being labelled CS and C, respectively. The hydrogels were characterised with respect to their physical properties (swelling capacity, water content, morphology, mechanical resistance, and stability), before and after sterilisation, and they showed adequate values for the intended application. The hydrogels of both formulations were able to sustain controlled drug-release for, at least, 48 h. They were demonstrated to be non-irritant, highly haemocompatible, and non-cytotoxic, and revealed good antimicrobial properties against Staphylococcus aureus and Pseudomonas aeruginosa. Steam-heat sterilisation did not compromise the material’s properties. The in vivo performance of C hydrogel loaded with Octiset^® was evaluated in a case study with a dog. The efficient recovery of the wounds confirms its potential as an alternative for wound treatment. To our knowledge, this is the first time that wound dressings loaded with Octiset^®, one of the most efficient drugs for wound treatment, were prepared and tested. Full article

Nuclear accidents and decommissioning in the nuclear industry would release a large number of radioactive aerosols which endangers the natural environment and the health of workers. Therefore, there is an urgent need for environment-friendly aerosol suppressants to control and handle environmental pollution problems caused by radioactive aerosols. In this paper, sodium alginate (SA), a type of polyphenol material (TP), and alkyl glycosides (APGs) were selected as the components of the compound aerosol suppressant and the optimal proportion was generated via the method of D-optimal mixture design. Furthermore, the cesium aerosol sedimentation effect of the optimized compound aerosol suppressants was evaluated via sedimentation efficiency, the change in particle concentration cumulative concentration fraction of the cesium aerosol sedimentation process. The results showed that the aerosol sedimentation efficiency was 99.82% which was much higher than nature settlement, 18.6% and water spraying sedimentation, 43.3%. Moreover, after spraying the compound suppressant, it displayed a good effect on settling the cesium aerosol particles with a diameter of less than 1 µm, as the concentration of particles was reduced from 55.49% to 44.53%. Finally, the sedimentation mechanism of the compound aerosol suppressant and cesium aerosol particles, such as the coagulation effect, was analyzed using the particle size distribution. Full article

Bone is a large and dynamic tissue and its maintenance requires high amounts of energy as old or damaged bone structures need to be replaced during the process of bone remodeling. Glucose homeostasis is an essential prerequisite for a healthy bone and vice versa, the skeleton can act as an endocrine organ on energy metabolism. We recently showed that hypothyroidism in mice leads to an almost complete arrest of bone remodeling. Here, we aimed to investigate whether the profound suppression of bone remodeling affects whole-body glucose homeostasis. To that end, male C57BL/6JRj mice were rendered hypothyroid over 4 weeks using methimazole and sodium perchlorate in the drinking water. We confirmed trabecular bone gain due to decreased bone turnover in hypothyroid mice with decreased cortical but increased vertebral bone strength. Further, we found impaired glucose handling but not insulin resistance with hypothyroidism. In hypothyroid bone, glucose uptake and expression of glucose transporter Glut4 were reduced by 44.3% and 13.9%, respectively, suggesting lower energy demands. Nevertheless, hypothyroidism led to distinct changes in glucose uptake in muscle, liver, and epididymal white adipose tissue (eWAT). Reduced glucose uptake (−30.6%) and Glut1/Glut4 transcript levels (−31.9%/−67.5%) were detected in muscle tissue. In contrast, in liver and eWAT we observed increased glucose uptake by 25.6% and 68.6%, respectively, and upregulated expression of glucose transporters with hypothyroidism. To more specifically target bone metabolism and discriminate between the skeletal and systemic effects of hypothyroidism on energy metabolism, male mice were treated with zoledronate (ZOL), a bisphosphonate, that led to decreased bone turnover, trabecular bone gain, and reduced local glucose uptake into bone (−40.4%). However, ZOL-treated mice did not display alterations of systemic glucose handling nor insulin tolerance. Despite the close mutual crosstalk of bone and glucose metabolism, in this study, we show that suppressing bone remodeling does not influence whole-body glucose homeostasis in male mice. Full article

Biocompatible nanogels are highly in demand and have the potential to be used in various applications, e.g., for the encapsulation of sensitive biomacromolecules. In the present study, we have developed water-in-oil microemulsions of sodium alginate sol/hexane/Span 20 as a template for controlled synthesis of alginate nanogels, cross-linked with 3d transition metal cations (Mn²⁺, Fe³⁺, and Co²⁺). The results suggest that the stable template of 110 nm dimensions can be obtained by microemulsion technique using Span 20 at concentrations of 10mM and above, showing a zeta potential of −57.3 mV. A comparison of the effects of the cross-links on the morphology, surface charge, protein (urease enzyme) encapsulation properties, and stability of the resulting nanogels were studied. Alginate nanogels, cross-linked with Mn²⁺, Fe³⁺, or Co²⁺ did not show any gradation in the hydrodynamic diameter. The shape of alginate nanogels, cross-linked with Mn²⁺ or Co²⁺, were spherical; whereas, nanogels cross-linked with Fe³⁺ (Fe–alginate) were non-spherical and rice-shaped. The zeta potential, enzyme loading efficiency, and enzyme activity of Fe–alginate was the highest among all the nanogels studied. It was found that the morphology of particles influenced the percent immobilization, loading capacity, and loading efficiency of encapsulated enzymes. These particles are promising candidates for biosensing and efficient drug delivery due to their relatively high loading capacity, biocompatibility, easy fabrication, and easy handling. Full article

The challenges of handling user-hostile alkaline solutions in the conventional alkali-activated binders (AAB) have initiated the development of “just add water” or one-part solid-based AAB systems. This paper aims to present a preliminary investigation on the development of one-part ambient-cured alkali-activated binders produced by synthesising high-calcium fly ash (HCFA) and ground granulated blast furnace slag (GGBS) using sodium metasilicate anhydrous. Three test series were conducted in this study to investigate the effects of GGBS/binder, activator/binder and water/binder ratios on the fresh and hardened properties of the one-part synthesis AAB system. It was found that the SiO₂/Al₂O₃ molar ratio plays an important role in the attainment of compressive strength and limits the amounts of solid activators effective in contributing to the alkali-activation reaction process. The optimum SiO₂/Al₂O₃ molar ratio was found between 3.20 and 3.30. The test results revealed that the optimum proportion between HCFA and GGBS was discovered at a GGBS/binder ratio of 0.50. The optimum activator/binder ratio was between 0.08 and 0.12, and it is recommended that the water/binder ratio should not exceed 0.50. This study demonstrated the potential of the one-part synthesis method in the production of alkali-activated binder for practical structural applications. Full article

Growth hormone (GH) exerts multiple effects on different organs including the kidneys, either directly or via its main mediator, insulin-like-growth factor-1 (IGF-1). The GH/IGF1 system plays a key role in normal kidney development, glomerular hemodynamic regulation, as well as tubular water, sodium, phosphate, and calcium handling. Transgenic animal models demonstrated that GH excess (and not IGF1) may lead to hyperfiltration, albuminuria, and glomerulosclerosis. GH and IGF-1 play a significant role in the early development of diabetic nephropathy, as well as in compensatory kidney hypertrophy after unilateral nephrectomy. Chronic kidney disease (CKD) and its complications in children are associated with alterations in the GH/IGF1 axis, including growth retardation, related to a GH-resistant state, attributed to impaired kidney postreceptor GH-signaling and chronic inflammation. This may explain the safety of prolonged rhGH-treatment of short stature in CKD. Full article