Search Results (28)

Carbon fiber-reinforced resin matrix composites (CFRC) are extensively used in aerospace, automotive manufacturing, and sports equipment. However, the brittle nature of the resin matrix causes CFRC to exhibit severe vibrations and noise under dry friction conditions. Enhancing the intrinsic damping properties of the resin matrix serves as a fundamental and effective strategy to mitigate vibration and noise radiation in composite components. This study systematically investigates high-temperature co-curing damping composites using co-curing technology, aiming to improve the mechanical performance and damping characteristics of traditional fiber-reinforced epoxy resin composites. A novel carbon fiber-reinforced terminal carboxyl nitrile epoxy pre-polymer composite material demonstrates both stable chemical properties and excellent high-temperature resistance. Through formulation adjustments, the curing temperature and time of epoxy resin are matched with those of the terminal carboxyl nitrile epoxy pre-polymer. The performance of epoxy carbon fiber composites was evaluated through tensile tests, flexural tests, impact tests, infrared spectroscopy, thermogravimetric analysis, dynamic mechanical analysis, scanning electron microscopy, and X-ray diffraction. Results show that blending epoxy resin with terminal carboxyl nitrile liquid rubber enhances energy dissipation by increasing intermolecular friction and hydrogen bonding interactions. The damping ratio of epoxy resin-based carbon fiber composites reaches as high as 1.67%. Tensile strength, flexural strength, and impact strength reach 1968 MPa, 1343 MPa, and 127 kJ/m², respectively. The addition of terminal carboxylated nitrile liquid rubber facilitates the formation of continuous friction membranes, enhancing friction stability. Tensile tests demonstrate that carbon fiber composites containing 25% terminal carboxylated nitrile liquid rubber outperforms other formulations. As evidenced by impact tests, the performance of the prepared composites is superior to that of other configurations. Dynamic mechanical analysis indicates that the 25% rubber-containing composites exhibit enhanced damping characteristics and higher loss modulus. Experimental results confirm that this study advances the development of functional composites for vibration reduction and noise control applications. Full article

Acoustic cavities play a role in many technological applications in civil, naval, and aerospace engineering. This study examines the vibroacoustic performance of a forced oscillating top membrane of a cylindrical container fully filled with a compressible and nonviscous fluid. For the case of harmonic motion and using Helmholtz’s equation, the velocity potential is deduced, and the acoustic pressure is obtained using Bernoulli’s linearized equation. Taking into account the dynamic equation for the membrane with the interacting fluid with the different terms expanded in a modal series and after an integration procedure over the membrane surface, a simple analytical quadratic equation is deduced, and the coupled natural frequencies of the membrane are obtained. For the case of forced vibrations, a transfer function is obtained for calculating the frequency spectrum response of the fluid–membrane interacting system. In particular, the membrane deformation spectrum and the acoustic cavity pressure spectrum are obtained for different location points. Moreover, the spectrum of the mean quadratic values of the membrane deflexion and acoustic pressure are deduced, along with its variation with different parameters such as drum height, membrane radius, fluid density, load position, sound speed, and membrane tension. The variation in sensitivity with frequency and other different parameters is also analysed. The results are contrasted with those obtained by other authors to validate the present work. Full article

Access to clean water is a pressing global concern and membrane technologies play a vital role in addressing this challenge. Thin-film composite membranes prepared via interfacial polymerization (IPol) using meta-phenylenediamine (MPD) and trimesoyl chloride (TMC) exhibit excellent separation performance, but face limitations such as fouling and low hydrophilicity. This study investigated the interaction between MPD and sulfonated zinc phthalocyanine, Zn(SO₂⁻)₄Pc, as a potential strategy for enhancing membrane properties. Using Density Functional Theory (DFT) and Time-Dependent DFT (TD-DFT), we analyzed the optimized geometries, electronic structures, UV–Vis absorption spectra, FT-IR vibrational spectra, and molecular electrostatic potentials of MPD, Zn(SO₂⁻)₄Pc, and their complexes. The results show that MPD/Zn(SO₂⁻)₄Pc exhibits reduced HOMO-LUMO energy gaps and enhanced charge delocalization, particularly in aqueous environments, indicating improved stability and reactivity. Spectroscopic features confirmed strong interactions via hydrogen bonding and π–π stacking, suggesting that Zn(SO₂⁻)₄Pc can act as a co-monomer or additive during IPol to improve polyamide membrane functionality. A conformational analysis of MPD/Zn(SO₂⁻)₄Pc was conducted using density functional theory (DFT) to evaluate the impact of dihedral rotation on molecular stability. The 120° conformation was identified as the most stable, due to favorable π–π interactions and intramolecular hydrogen bonding. These findings offer computational evidence for the design of high-performance membranes with enhanced antifouling, selectivity, and structural integrity for sustainable water treatment applications. Full article

In accordance with growing environmental pressures and the demand for sustainable industrial practices, membrane technologies have emerged as key enablers for increasing efficiency, reducing emissions, and supporting circular processes across multiple sectors. This review focuses on the integration among microalgae-based systems, offering innovative and sustainable solutions for biomass production, carbon capture, and industrial wastewater treatment. In cultivation, membrane photobioreactors (MPBRs) have demonstrated biomass productivity up to nine times greater than that of conventional systems and significant reductions in water (above 75%) and energy (approximately 0.75 kWh/m³) footprints. For carbon capture, hollow fiber membranes and hybrid configurations increase CO₂ transfer rates by up to 300%, achieving utilization efficiencies above 85%. Coupling membrane systems with industrial effluents has enabled nutrient removal efficiencies of up to 97% for nitrogen and 93% for phosphorus, contributing to environmental remediation and resource recovery. This review also highlights recent innovations, such as self-forming dynamic membranes, magnetically induced vibration systems, antifouling surface modifications, and advanced control strategies that optimize process performance and energy use. These advancements position membrane-based microalgae systems as promising platforms for carbon-neutral biorefineries and sustainable industrial operations, particularly in the oil and gas, mining, and environmental technology sectors, which are aligned with global climate goals and the UN Sustainable Development Goals (SDGs). Full article

Background/Objectives: Nanocarrier particle design for treating chronic pulmonary diseases presents several challenges, including anatomical and physiological barriers. Drug-repurposing technology using monodispersed spherical silica is one of the innovative ways to deliver drugs. In the present study, the anticancer potential of combinational cisplatin/ribavirin was explored for targeted lung cancer therapeutics. Methods: Monodispersed spherical silica (80 nm) capable of diffusing into the tracheal mucus region was chosen and doped with 10 wt% superparamagnetic iron oxide nanoparticles (SPIONs). Subsequently, it was wrapped with chitosan (Chi, 0.6 wt/vol%), functionalized with 5% wt/wt cisplatin (Cp)/ribavarin (Rib) and angiotensin-converting enzyme 2 (ACE-2) (1.0 μL/mL). Formulations are based on monodispersed spherical silica or halloysite and are termed as (S/MSSiO₂/Chi/Cp/Rib) or (S/Hal/Chi/Cp/Rib), respectively. Results: X-ray diffraction (XRD) and diffuse reflectance UV-visible spectroscopy (DRS-UV-vis) analysis of S/MSSiO₂/Chi/Cp/Rib confirmed the presence of SPION nanoclusters on the silica surface (45% coverage). The wrapping of chitosan on the silica was confirmed with a Fourier transformed infrared (FTIR) stretching band at 670 cm⁻¹ and ascribed to the amide group of the polymer. The surface charge by zetasizer and saturation magnetization by vibrating sample magnetometer (VSM) were found to be −15.3 mV and 8.4 emu/g. The dialysis membrane technique was used to study the Cp and Rib release between the tumor microenvironment and normal pH ranges from 5.5 to 7.4. S/MSSiO₂/Chi formulation demonstrated pH-responsive Cp and Rib at acidic pH (5.6) and normal pH (7.4). Cp and Rib showed release of ~27% and ~17% at pH 5.6, which decreases to ~14% and ~3.2% at pH 7.4, respectively. To assess the compatibility and cytotoxic effect of our nanocomposites, the cell viability assay (MTT) was conducted on cancer lung cells A549 and normal HEK293 cells. Conclusions: The study shows that the designed nanoformulations with multifunctional capabilities are able to diffuse into the lung cells bound with dual drugs and the ACE-2 receptor. Full article

The sealing technology of proton exchange membrane fuel cells (PEMFCs) is a critical factor in ensuring their performance, impacting driving safety and range efficiency. To guarantee the safe operation of PEMFCs in complex environments, it is essential to conduct related sealing research. The structure of the fuel cell sealing system is complex, with components in close contact, and identifying factors that affect its sealing performance is crucial for the development and application of the cells. This paper briefly describes the sealing mechanism of PEMFCs and introduces four typical sealing structures. It considers both the assembly and operation processes, summarizing assembly errors, sealing gaskets, and sealing leaks as well as vibration, cyclic temperature and humidity, and cyclic assembly. The research status of the sealing system in simulations and experiments is reviewed in detail. The key factors affecting the sealing performance of fuel cells are emphasized, highlighting the significance of dynamic detection of the gasket status, stack performance improvement under cumulative errors, and multi-objective optimization models combining contact pressure with the characteristics of stack components. Full article

Triply periodic minimal surfaces (TPMSs) are found in many natural objects including butterfly wings, sea urchins, and biological membranes. They simultaneously have zero mean curvature at every point and a crystallographic group symmetry. A metamaterial can be created from such periodic surfaces or used as a reinforcement of a composite material. While a TPMS as a mathematical object has been known since 1865, only novel additive manufacturing (AM) technology made it possible to fabricate cellular materials with complex TPMS shapes. Cellular TPMS-based metamaterials have remarkable properties related to wetting/liquid penetration, shock absorption, and the absence of stress concentrators. Recent studies showed that TPMSs are also found in natural crystals when electron surfaces are considered. Artificial crystal-inspired metamaterials mimic such crystals including zeolites and schwarzites. These metamaterials are used for shock, acoustic waves, and vibration absorption, and as structural materials, heat exchangers, and for other applications. The choice of the crystalline cell of a material, as well as its microstructure, plays a decisive role in its properties. The new area of crystal-inspired materials has many common features with traditional biomimetics with models being borrowed from nature and adjusted for engineering applications. Full article

Among the various water purification techniques, advancements in membrane technology, with better fabrication and analysis, are receiving the most research attention. The piezo-catalytic degradation of water pollutants is an emerging area of research in water purification technology. This review article focuses on piezoelectric polyvinylidene difluoride (PVDF) polymer-based membranes and their nanocomposites for textile wastewater remediation. At the beginning of this article, the classification of piezoelectric materials is discussed. Among the various membrane-forming polymers, PVDF is a piezoelectric polymer discussed in detail due to its exceptional piezoelectric properties. Polyvinylidene difluoride can show excellent piezoelectric properties in the beta phase. Therefore, various methods of β-phase enhancement within the PVDF polymer and various factors that have a critical impact on its piezo-catalytic activity are briefly explained. This review article also highlights the major aspects of piezoelectric membranes in the context of dye degradation and a net-zero approach. The β-phase of the PVDF piezoelectric material generates an electron–hole pair through external vibrations. The possibility of piezo-catalytic dye degradation via mechanical vibrations and the subsequent capture of the resulting CO₂ and H₂ gases open up the possibility of achieving the net-zero goal. Full article

Capacitive micromachined ultrasonic transducer (CMUT) has been widely studied due to its excellent resonance characteristics and array integration. This paper presents the first study of the CMUT electrostatic stiffness resonant accelerometer. To improve the sensitivity of the CMUT accelerometer, this paper innovatively proposes the CMUT ring-perforation membrane structure, which effectively improves the acceleration sensitivity by reducing the mechanical stiffness of the elastic membrane. The acceleration sensitivity is 10.9 (Hz/g) in the acceleration range of 0–20 g, which is 100% higher than that of the conventional CMUT structure. This research contributes to the acceleration measurement field of CMUT and can effectively contribute to the breakthrough of vibration acceleration monitoring technology in aerospace, medical equipment, and automotive electronics. Full article

With the continuous improvement in human awareness of environmental protection, energy savings, and emission reduction, as well as the vigorous development of precision machinery and process technology, energy-saving and efficient diaphragm pumps have become a hot research topic at home and abroad. The diaphragm pump is a membrane-isolated reciprocating transport pump that isolates the transport medium from the piston through the diaphragm and can be used to transport high-viscosity, volatile, and corrosive media, and the symmetrical structure can make it easier for the diaphragm pump to achieve stable operation, reduce vibration and noise, and extend the life of the pump. This paper summarizes the development and research status of diaphragm pumps in recent years, including diaphragm pump structure, working principle, category, cavitation research, wear research, fault diagnosis research, vibration and noise research, fluid–solid-interaction research, and optimum research on one-way valves and diaphragms. It also puts forward some reasonable and novel viewpoints, such as applying the theory of entropy production to explore the motion mechanism of diaphragm pumps, optimizing the performance of diaphragm pumps, using new technologies to study new materials for diaphragm pumps, and designing diaphragm protection devices. This review provides valuable references and suggestions for the future development and research of diaphragm pumps. Full article

Fractional calculus is an essential tool in studying new phenomena in hydromechanics and heat and mass transfer, particularly anomalous hydromechanical advection–dispersion considering the fractal nature of the porous medium. They are valuable in solving the urgent problem of convective mass transfer in a porous medium (e.g., membranes, filters, nozzles, convective coolers, vibrational prillers, and so on). Its solution allows for improving chemical engineering and technology workflows, refining process models for obtaining porous granular materials, realizing the convective cooling of granular and grain materials, and ensuring the corresponding apparatuses’ environmental safety. The article aims to develop a reliable convective mass transfer model for a porous medium and proposes a practical approach for its parameter identification. As a result, a general scientific and methodological approach to parameter identification of the fractional convective mass transfer model in a porous medium was proposed based on available experimental data. It mainly used Riemann–Liouville fractional time and coordinate derivatives. The comprehensive application of the Laplace obtained the corresponding general solution transform with respect to time and a coordinate, the Mittag-Leffler function, and specialized functions. Different partial solutions in various application case studies proved this solution. Moreover, the algorithm for practically implementing the developed approach was proposed to evaluate parameters for the considered model by evaluation data. It was reduced to the two-parameter model and justified by the available experimental data. Full article

Membrane separation processes have become increasingly popular in many industries because of their ability to treat wastewater and purify water. However, one of the main problems related to the processes is organic fouling, which can significantly reduce their efficiency and cause membrane damage. This review provides a summary of the various forms of organic fouling that can occur in membrane separation methods and examines the factors that lead to their development. The article evaluates the progress made in different techniques designed to manage and reduce organic fouling, such as physical cleaning methods, chemical cleaning agents, and modifications to the membrane surface, including ultrasonic and membrane vibration methods. The review also highlights recent advances in emerging 3D printing technology to mitigate membrane fouling. Finally, the review provides a brief summary of the conclusions and future directions for research in the field of organic fouling control and mitigation in membrane separation processes. Full article

Much attention has been paid to the surface modification of artificial skin barriers for the treatment of skin tissue damage. Chitosan is one of the natural materials that could be characterized by its biocompatibility. A number of methods for the preparation of chitosan membranes have been described in scientific articles, including solvent casting methods. This study investigates an improved technology to produce chitosan membranes. Thus, chitosan membranes were prepared using a vibration-assisted solvent casting method. First, aqueous acetic acid was used to pretreat chitosan. Then, free-standing chitosan membranes were prepared by solvent casting on nanoporous anodized aluminum oxide (AAO) membrane templates, allowing for the solvent to evaporate. Using finite element methods, a study was obtained showing the influence of chitosan solutions of different concentrations on the fluid flow into nanopores using high-frequency excitation. The height of the nanopillars and the surface area of the chitosan membrane were also evaluated. In this study, the surface area of the chitosan membrane was found to increase by 15, 10 and 6 times compared to the original flat surface area. The newly produced nanopillared chitosan membranes will be applicable in the fabrication of skin barriers due to the longer nanopillars on their surface and the larger surface area. Full article

Piezoelectric Laterally Vibrating Resonators (LVRs) have attracted significant attention as a potential technology for next-generation wafer-level multi-band filters. Piezoelectric bilayer structures such as Thin-film Piezoelectric-on-Silicon (TPoS) LVRs which aim to increase the quality factor (Q) or aluminum nitride and silicon dioxide (AlN/SiO₂) composite membrane for thermal compensation have been proposed. However, limited studies have investigated the detailed behaviors of the electromechanical coupling factor (K²) of these piezoelectric bilayer LVRs. Herein, AlN/Si bilayer LVRs are selected as an example, we observed notable degenerative valleys in K² at specific normalized thicknesses using two-dimensional finite element analysis (FEA), which has not been reported in the previous studies of bilayer LVRs. Moreover, the bilayer LVRs should be designed away from the valleys to minimize the reduction in K². Modal-transition-induced mismatch between electric and strain fields of AlN/Si bilayer LVRs are investigated to interpret the valleys from energy considerations. Furthermore, the impact of various factors, including electrode configurations, AlN/Si thickness ratios, the Number of Interdigitated Electrode (IDT) Fingers (NFs), and IDT Duty Factors (DFs), on the observed valleys and K² are analyzed. These results can provide guidance for the designs of piezoelectric LVRs with bilayer structure, especially for LVRs with a moderate K² and low thickness ratio. Full article

To modernize wastewater treatment plants, a pilot-scale anaerobic/anoxic/oxic-vibrating membrane bioreactor (A²/O-VMBR) was developed and successfully operated. Despite a low C/N ratio, the A²/O-VMBR achieved removal rates of 61.10%, 93.77%, 72.86%, and 54.75% for COD, TN, TP, and NH₃-N, respectively. The maximum and extremity transmembrane pressures were 45 kPa, and 80 kPa, respectively, with no sludge bulking observed. The VMBR saved over 96–98% of energy compared to traditional MBR plants, making it a better option for municipal wastewater treatment. High-throughput sequencing analysis revealed identical bacterial population structures in samples obtained from the treatment units, with genera having nitrifying, denitrifying, hydrolyzing, and glycogen-accumulating activities, which allowed for nitrogen removal. The key functional microorganisms responsible for nitrification–denitrification were species belonging to the genera FCPU426, Fusobacteria, Planctomycetes, Verrucomicrobia, and Epsilonbacteraeota. The integrated experimental system produced favorable results in improving wastewater quality, highlighting the usability of the A²/O-VMBR technology. Therefore, this technique holds potential for further investigation into the context of wastewater treatment and recovery. Full article