Search Results (6)

To improve the efficiency and stability of the system, this paper proposes a monolithic integrated optical path design for a cavity optomechanical accelerometer based on a 250 nm top silicon thickness silicon-on-insulator (SOI) wafer instead of readout through U-shape fiber coupling. Finite Element Analysis (FEA) and Finite-Difference Time-Domain (FDTD) methods are employed to systematically investigate the performance of key optical structures, including the resonant modes and bandgap characteristics of photonic crystal (PhC) microcavities, transmission loss of strip waveguides, coupling efficiency of tapered-lensed fiber-to-waveguide end-faces, coupling characteristics between strip waveguides and PhC waveguides, and the coupling mechanism between PhC waveguides and microcavities. Simulation results demonstrate that the designed PhC microcavity achieves a quality factor (Q-factor) of 2.26 × 10⁵ at a 1550 nm wavelength while the optimized strip waveguide exhibits a low loss of merely 0.2 dB over a 5000 μm transmission length. The strip waveguide to PhC waveguide coupling achieves 92% transmittance at the resonant frequency, corresponding to a loss below 0.4 dB. The optimized edge coupling structure exhibits a transmittance of 75.8% (loss < 1.2 dB), with a 30 μm coupling length scheme (60% transmittance, ~2.2 dB loss) ultimately selected based on process feasibility trade-offs. The total optical path system loss (input to output) is 5.4 dB. The paper confirms that the PhC waveguide–microcavity evanescent coupling method can effectively excite the target cavity mode, ensuring optomechanical coupling efficiency for the accelerometer. This research provides theoretical foundations and design guidelines for the fabrication of high-precision monolithic integrated cavity optomechanical accelerometers. Full article

A tunable dual-band terahertz sensor based on graphene is proposed. The sensor consists of a metal bottom layer, a middle dielectric layer, and single-layer graphene patterned with four strips on the top. The numerical simulations results show that the proposed sensor exhibits two significant absorption peaks at 2.58 THz and 6.07 THz. The corresponding absorption rates are as high as nearly 100% and 98%, respectively. The corresponding quality factor (Q) value is 11.8 at 2.58 THz and 29.6 at 6.07 THz. By adjusting the external electric field or chemical doping of graphene, the positions of the dual-frequency resonance peak can be dynamically tuned. The excitation of plasma resonance in graphene can illustrate the mechanism of the sensor. To verify the practical application of the device, the terahertz response of different kinds and different thicknesses of the analyte is investigated and analyzed. A phenomenon of obvious frequency shifts of the two resonance peaks can be observed. Therefore, the proposed sensor has great potential applications in terahertz fields, such as material characterization, medical diagnosis, and environmental monitoring. Full article

For improving the night recognition of road markings and enhancing the driving safety of asphalt pavements, single-factor optimization is used to investigate the effects of the component materials, including luminescent power, pigment, filler, and anti-sedimentation agent, on the luminous performance of a coating. Additionally, their composition ratios are optimized using response surface methodology. A phosphorescent marking coating is prepared to investigate the micromorphology, excitation, and emission properties using scanning electron microscopy (SEM) and molecular fluorescence spectroscopy (MFS). The optimum thickness of the coating on an asphalt pavement is investigated, and the durability of the coating on asphalt pavement using a wheel rutting test is evaluated. The results show that the 300 mesh yellow-green luminous powder has the optimal overall performance, with an initial luminescence that exceeds that of orange and sky blue by three times. Initial brightness is mainly influenced by aluminate luminescent powder (ALP), which increases with the dosage. ALP and fumed silica powder (FSP) have a positive effect on brightness after centrifugation, and the effect of FSP dosage is more significant. ALP, rutile titanium dioxide powder (RTDP), and FSP influence the wear value of the coating, and the magnitude of the effect is RTDP > FSP > ALP. The optimal dosages of the main component are 27% ALP, 5% RTDP, and 0.8% FSP. The results of SEM show that the components in the coating are evenly dispersed, and the surface of the coating is rough. The peak excitation wavelength of 420 nm means that the coating has the best excitation effect in UV light, and its emission spectrum in the 440–760 nm wavelength range is well within the sensitive recognition zone of the human eye. The initial brightness gradually reached 4.38 cd/m² when the coating thickness was increased from 482 μm to 546 μm, and the optimal application thickness of the luminous coating was determined to be 500 μm. At high and normal temperatures, the rutting stripping rates of the luminous marking coating are 16.8% and 8.2%, indicating its satisfactory durability. This study provides an experimental basis for the ratio optimization design of a luminous coating for asphalt pavements. Full article

The vibration of the vertical system of a cold rolling mill is a major concern for factory production. In factory production, it is found that the thickness control system with dynamic stiffness compensation of the rolling mill has a significant impact on the rolling mill vibration. In this work, a mechanical hydraulic coupling vibration model of a cold rolling mill with a thickness control system with dynamic stiffness compensation was established. MATLAB/Simulink was used to simulate and analyze the vibration response characteristics of the mechanical structure of the rolling mill and mechanical hydraulic coupling system considering the dynamic stiffness compensation control mode and position control mode of the upper cylinder. We found that the control system changed the vibration response of the mechanical structure, and different control modes have different effects on the vibration response curve. When the rolling mill works in the vibration area, the thickness difference at the strip steel outlet would be larger. Considering the rolling mill vibration and strip surface quality, the excitation of the strip inlet thickness can be achieved by adjusting the dynamic stiffness compensation system and changing the rolling speed reasonably to achieve good vibration suppression and control effects. Full article

Air-coupled excitation and reception of ultrasonic guided waves is already used for non-destructive testing and evaluation (NDT & E). Usually for air-coupled NDT & E purposes the lowest zero-order antisymmetric Lamb wave mode A₀ is used, because it is most sensitive to internal defects and thickness variations. The velocity of the A₀ mode is reduced with a reducing frequency and at low frequencies may become slower than the ultrasound velocity in air. Such a wave is named a slow Lamb wave. The objective of this research was the development and investigation of an air-coupled excitation method of the slow zero-order antisymmetric Lamb wave based on application of a piezoceramic ultrasonic array. We have proposed to excite the A₀ mode by a planar air-coupled phased array with rectangular elements. The array is matched to the wavelength of the A₀ mode in the film. Performance of such an excitation method was investigated both theoretically and experimentally. Two excitation methods of the array were analysed: when all array elements were excited simultaneously or one by one with a proper delay. In order to reduce crosstalk between array elements via the air gap, we have proposed an optimization procedure based on additional shifts of electric excitation impulses of the array elements. For experimental verification of the proposed approach a prototype of the air-coupled eight element array made of Pz-29 piezoceramic strips was manufactured. Experimental validation confirmed the possibility of exciting the slow A₀ Lamb wave mode through the air gap in thin plates and films. Full article

Experimental measurement results of a 1.75 mm × 1.75 mm footprint area Capacitive Micromachined Ultrasonic Transducer (CMUT) planar array fabricated using a bisbenzocyclobutene (BCB)-based adhesive wafer bonding technique has been presented. The array consists of 40 × 40 square diaphragm CMUT cells with a cavity thickness of 900 nm and supported by 10 µm wide dielectric spacers patterned on a thin layer of BCB. A 150 µm wide one µm thick gold strip has been used as the contact pad for gold wire bonding. The measured resonant frequency of 19.3 MHz using a Polytec™ laser Doppler vibrometer (Polytec™ MSA-500) is in excellent agreement with the 3-D FEA simulation result using IntelliSuite™. An Agilent ENA5061B vector network analyzer (VNA) has been used for impedance measurement and the resonance and anti-resonance values from the imaginary impedance curve were used to determine the electromechanical coupling co-efficient. The measured coupling coefficient of 0.294 at 20 V DC bias exhibits 40% higher transduction efficiency as compared to a measured value published elsewhere for a silicon nitride based CMUT. A white light interferometry method was used to measure the diaphragm deflection profiles at different DC bias. The diaphragm center velocity was measured for different sub-resonant frequencies using a Polytec™ laser Doppler vibrometer that confirms vibration of the diaphragm at different excitation frequencies and bias voltages. Transmit and receive operations of CMUT cells were characterized using a pitch-catch method and a −6 dB fractional bandwidth of 23% was extracted from the received signal in frequency domain. From the measurement, it appears that BCB-based CMUTs offer superior transduction efficiency as compared to silicon nitride or silicon dioxide insulator-based CMUTs, and provide a very uniform deflection profile thus making them a suitable candidate to fabricate highly energy efficient CMUTs. Full article