Search Results (19)

Active continental margins, generally characterized by narrow shelves incised by canyons, are pervasively shaped by submarine landslides that can occur near coastal areas. In this context, creating landslide susceptibility maps is the first step in landslide geohazard assessment. This paper focuses on shallow-water submarine landslides along the Capo d’Orlando continental margin and presents a related susceptibility map using the Weight of Evidence method. This method quantifies the strength of the association between a landslide inventory and predisposing factors. A geomorphological analysis of the continental shelf and upper slope yielded a landslide inventory of 450 initiation points, which were combined with five specifically selected preconditioning factors. The results revealed that the most favourable conditions for shallow-water landslides include slopes between 5° and 15°, proximity to faults (<1 km), proximity to river mouths (<2 km), the presence of consolidated lithologies and sandy terraces, and slopes facing NE and E. The landslide susceptibility map indicates that susceptible areas are in canyon heads and flanks, as well as in undisturbed slope portions near canyon heads where retrogressive landslides are likely. The model results are robust (AUC = 0.88), demonstrating that this method can be effectively applied in areas with limited geological data for preliminary susceptibility assessments. Full article

Variations in the warm formability of AA7075 sheets are primarily attributed to differences in precipitate morphology resulting from distinct thermal histories. To better understand this relationship, this study systematically investigates the influence of precipitate characteristics—quantified by the product of precipitate volume fraction and average radius—on forming limits across various thermal routes in warm forming processes. A modified Cockcroft–Latham ductile fracture model incorporating this microstructural parameter was developed, calibrated against experimental data from warm isothermal Nakajima tests, and implemented within a finite element framework. The proposed model enables the accurate prediction of forming limit curves with minimal experimental effort, thereby significantly reducing the reliance on extensive mechanical testing. Building upon the validated FE model, a practical methodology for rapid R-value estimation under warm forming conditions was established, involving the design of specimen geometries optimised for isothermal Nakajima testing. This approach achieved R-value predictions within 5% deviation from conventional uniaxial tensile test results. Furthermore, experimental results indicated that AA7075 sheets exhibited nearly isotropic deformation behaviour under retrogression warm forming conditions. Overall, the methodology proposed in this study bridges the gap between formability prediction and process simulation, offering a robust and scalable framework for the industrial optimisation of warm forming processes for high-strength aluminium alloys. Full article

In this study, various raw materials, including silica sand, silica fume, calcium hydroxide, α-alumina, and nano-activated alumina, were used to produce hydroceramic systems with varying Ca/Si/Al ratios to optimize their high-temperature resistance. The hydroceramic slurries, with a constant density of 1.65 g/cm³, were all designed to have a setting time of more than 4 h at the condition of 240 °C and 50 MPa and then cured at the same condition for 2, 30, and 90 days to evaluate their long-term performances. Subsequently, compressive strength, water permeability, mercury intrusion porosimetry, thermogravimetry, and X-ray diffraction tests were conducted on set samples at various curing times to analyze the hydroceramic systems’ long-term stability and the underlying mechanism. The results indicated that the hydration reaction of α-Al₂O₃ was minimal, and its inclusion reduced the incorporation of silica sand in the hydration process. Nano-activated alumina improved the macroscopic properties of the hydroceramic systems and promoted the formation of a significant amount of tobermorite 11 Å. The addition of silica fume can enhance the system’s macroscopic properties and the long-term stability, promoting the reaction of silica sand. The long-term stability of slurries with a Ca/Si ratio of 1 was significantly better than that of slurries with a Ca/Si ratio of 0.5. The best-performing slurry can maintain a compressive strength of more than 19 MPa after being cured at 240 °C for 90 days. Full article

With the depletion of shallow oil and gas resources, wells are being drilled to deeper and deeper depths to find new hydrocarbon reserves. This study presents the selection and optimization process of the cement slurries to be used for the deepest well ever drilled in China, with a planned vertical depth of 11,100 m. The bottomhole circulating and static temperatures of the well were estimated to be 210 °C and 220 °C, respectively, while the bottomhole pressure was estimated to be 130 MPa. Laboratory tests simulating the bottomhole conditions were conducted to evaluate and compare the slurry formulations supplied by four different service providers. Test results indicated that the inappropriate use of a stirred fluid loss testing apparatus could lead to overdesign of the fluid loss properties of the cement slurry, which could, in turn, lead to abnormal gelation of the cement slurry during thickening time tests. The initial formulation given by different service providers could meet most of the design requirements, except for the long-term strength stability. The combined addition of crystalline silica and a reactive aluminum-bearing compound to oil well cement is critical for preventing microstructure coarsening and strength retrogression at 220 °C. Two of the finally optimized cement slurry formulations had thickening times more than 4 h, API fluid loss values less than 50 mL, sedimentation stability better than 0.02 g/cm³, and compressive strengths higher than 30 MPa during the curing period from 1 d to 30 d. Full article

This study primarily investigates the effect of fly ash (FA) content on the mechanical properties and hydration performance of alkali-activated ground granulated blast furnace slag cement (AAGC) and compares the related properties with ordinary Portland cement (OPC). Additionally, we examined the hydration products; performed thermal analysis, MIP, and SEM; and determined chemically bound water and pH values of AAGC. The compressive strength of AAGC showed a retrogression phenomenon from 3 to 28 days, with the 14-day and 28-day compressive strengths of AAGC being higher than those of OPC. The AAGC with 20% FA content exhibited the highest 28-day compressive strength (75 MPa). The hydration heat release rate curve of OPC and AAGC was divided into the initial induction period, induction period, acceleration period, deceleration period, and steady period. As FA content increased, the 28-day pore volume of AAGC increased, while pH values and chemically bound water decreased. SEM images of AAGC with low FA content showed more microcracks. Full article

Retrogression and re-aging (RRA) treatment has been proven to effectively overcome the trade-off between strength and corrosion resistance. Current research focuses on the heating rate, temperature, and holding time of retrogression treatment while ignoring the retrogression cooling ways. In this paper, the effects of RRA treatment with different retrogression cooling ways on the microstructure and properties of newly developed T’/η’ strengthened Al-Zn-Mg-Cu alloys were investigated by performing tests on mechanical properties, intergranular corrosion (IGC) resistance, and electrochemical corrosion behavior. The results show that the mechanical properties of samples subject to RRA treatment with water-quenching retrogression (ultimate tensile strength, yield strength, and elongation of 419.2 MPa, 370.2 MPa, and 15.9, respectively) are better than those of air-cooled and furnace-cooled samples. The corrosion resistance of water-quenching (IGC depth of 162.2 μm, corrosion current density of 0.833 × 10⁻⁵ A/cm²) and furnace-cooled samples (IGC depth of 123.7 μm, corrosion current density of 0.712 × 10⁻⁵ A/cm²) is better than that of air-cooled samples. Microstructure characterization reveals that the effect of the retrogression cooling rate on mechanical properties is related to the size of T’/η’ precipitates with grains as well as the proportion of T’ and η’, while the difference in corrosion resistance depends on the continuity of grain boundary precipitates (GBPs). With mechanical properties, corrosion resistance, and time cost taken into consideration, it is appropriate to select water quenching for retrogression. These findings offer valuable insights for further design to achieve superior performance in various applications. Full article

In order to study the root–soil composite system shear characteristics under the action of freeze–thaw cycles in the permafrost regions along the Qinghai–Tibet Highway (QTH) from the Beiluhe–Tuotuohe (B-T) section, the slopes in the permafrost regions along the QTH from the B-T section were selected as the object of the study. The direct shear test of root–soil composite systems under different amounts of freeze–thaw (F-T) cycles and gray correlations were used to analyze the correlation between the number of F-T cycles, water content, root content, and the soil shear strength index. The results show that the cohesion of the soil in the area after F-T cycles exhibits a significant stepwise decrease with an increase in F-T cycles, which can be divided into three stages: the instantaneous stage (a decrease of 46.73–56.42%), the gradual stage (a decrease of 14.80–25.55%), and the stabilization stage (a decrease of 0.61–2.99%). The internal friction angle did not exhibit a regular change. The root–soil composite system showed significant enhancement of soil cohesion compared with soil without roots, with a root content of 0.03 g/cm³ having the most significant effect on soil cohesion (increasing amplitude 65.20–16.82%). With an increase in the number of the F-T cycles, while the water content is greater than 15.0%, the greater the water content of the soil, the smaller its cohesion becomes. Through gray correlation analysis, it was found that the correlation between the number of F-T cycles, water content, root content, and soil cohesion after F-T cycles were 0.63, 0.72, and 0.66, respectively, indicating that water content had the most significant impact on soil cohesion after F-T cycles. The results of this study provide theoretical support for further understanding the variation law of the shear strength of root–soil composite systems in permafrost regions under F-T cycles and the influencing factors of plant roots to enhance soil shear strength under F-T cycles, as well as for the scientific and effective prevention and control of retrogressive thaw slump in the study area, the QTH stretches across the region. Full article

This study examines the effect of silica fume (SF) as a partial replacement for cement to prevent strength retrogression in hardened cement paste (HCP) and mortar at elevated temperatures. An experimental procedure was conducted on 320 specimens, replacing 0, 10, 20, and 30% of the cement by weight with SF. The residual compressive strength of the specimens was evaluated at room temperature (25 °C) and at 100, 200, 300, and 400 °C for 7, 28, and 56 days. The results indicate that the addition of SF to the cement paste and mortar improves the compressive strength both at 25 °C and at temperatures up to 400 °C. That is attributed to the formation of C-S-H phases, such as tobermorite and xonotlite. Additionally, the optimal residual compressive strength was achieved by adding 30% of SF. Therefore, XRD, SEM, and EDS techniques were employed to evaluate the microstructure of HCP specimens with 30% of SF. The results show that adding SF leads to a denser microstructure and lower porosity, resulting in more durable cement paste and mortar at ambient and elevated temperatures. In conclusion, using SF as a partial replacement for cement can be an effective way of developing sustainable fire-resistant construction materials. Full article

This study systematically investigated the performance and microstructure characterization of cryogenic rolling (CR) and room-temperature rolling (RTR) Al–Mg–Si alloys. The result showed that the hardness of the CR alloys decreased at the early aging stage, but that the hardness of the RTR alloys increased at the early aging stage. Retrogression phenomena were apparent in the CR alloys at the early aging stage. Despite undergoing the same solid solution treatment, a few substructures were still observed in the CR alloys, and the degree of recrystallization in the CR alloys was significantly inferior to that in the RTR alloys. After aging for 50 h, the strength and precipitates’ density in the CR 75 alloy were higher than that in the other alloys; this indicated that the substructures were beneficial to precipitation and precipitate growth. A precipitation strength model was employed to illustrate the precipitation contribution at different aging stages. The results showed that the CR 75 alloy obtained the strongest precipitation strengthening. Full article

This paper investigates the effect of retrogression time on the fatigue crack growth of a modified AA7475 aluminum alloy. Tests including tensile strength, fracture toughness, and fatigue limits were performed to understand the changes in properties with different retrogression procedures at 180 °C. The microstructure was characterized using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The findings indicated that as the retrogression time increased, the yield strength decreased from 508 MPa to 461 MPa, whereas the fracture toughness increased from 48 MPa√m to 63.5 MPa√m. The highest fracture toughness of 63.5 MPa√m was seen after 5 h of retrogression. The measured diameter of η’ precipitates increased from 6.13 nm at the retrogression 1 h condition to 6.50 nm at the retrogression 5 h condition. Prolonged retrogression also increased the chance of crack initiation, with slower crack growth rate in the long transverse direction compared to the longitudinal direction. An empirical relationship was established between fracture toughness and the volume fraction of age-hardening precipitates, with increasing number density of precipitates seen with increasing retrogression time. Full article

The influences of curing pressure on the physical and mechanical property development of oil well cement during long-term curing were studied. Five silica-enriched cement slurries designed without and with reinforcement materials (latex fiber and nano-graphene) were autoclaved at 200 °C under two different pressures. The low pressure (50 MPa) curing was conducted for 2, 60, 90 and 180 days; the high pressure (150 MPa) curing was conducted for 2 and 360 days. The physical and mechanical properties of set cement were characterized by compressive strength, Young’s modulus, and water/gas permeability; the mineral composition and microstructure were determined by X-ray diffraction, mercury intrusion porosimetry, thermogravimetry and scanning electron microscope. Test results showed that high pressure (150 MPa) curing led to a more compact microstructure, which reduced the rate of strength retrogression in the long term. Samples with reinforcement materials, especially the latex fiber, showed higher compressive strength, Young’s modulus and lower permeability during long-term curing at both pressures. Full article

Neat well cement experience significant strength retrogression at high temperatures above 110 °C, especially at approximately 150 °C. To reveal the mechanism of performance degradation and guide the preparation of high-performance cement, we investigate the hydration process, mechanical behavior, and fracture process for well cement at the temperature of 150 °C based on molecular dynamics simulations and experiments. From triaxial pressure tests and Brazilian splitting tests, the strength, elastic modulus, and Poisson’s ratio of well cement decrease drastically with temperature increases from 80 °C to 150 °C. According to XRD, TG/DTG/DSC, and SEM, the hydration degree is insufficient, and larger pores exist in the microstructures. As the main binding phase of well cement, the mechanism of calcium silicate hydrates (C-S-H) influenced by curing temperatures is investigated through molecular dynamics simulations. C-S-H with calcium/silicon ratios (C/S) of 1.1 and 1.8 are simulated in the aqueous and solid states to investigate precipitation and mechanical behaviors. By reducing the C/S ratio to 1.1, the strength rebounds to a certain extent, and the adequacy of the hydration degree improved. It is found from the polymerization process that the increasing temperature promotes the polymerization rate, which is higher with C/S = 1.8 than that of 1.1. However, an increase in the C/S ratio will lead to a decrease in bridging oxygen content, thus a lower polymerization degree. The fracture simulations of C-S-H gels at different temperatures indicate that the failure of the C-S-H structure is mainly attributed to the disassembling of the calcium oxygen layers. With a higher temperature, there are fewer Ca-O bonds breaking, thus less strain energy consumed, resulting in worse performance. The elasticity of C-S-H, including Young’s and shear moduli, also exhibits certain degradations at a higher temperature. The elastic behavior of C-S-H with a low C/S ratio is generally higher than the high C/S. Full article

The human capacity to speak is fundamental to our advanced intellectual, technological and social development. Yet so very little is known regarding the evolutionary genetics of speech or its relationship with the broader aspects of evolutionary development in primates. In this study, we describe a large family with evolutionary retrograde development of the larynx and wrist. The family presented with severe speech impairment and incremental retrograde elongations of the pisiform in the wrist that limited wrist rotation from 180° to 90° as in primitive primates. To our surprise, we found that a previously unknown primate-specific gene TOSPEAK had been disrupted in the family. TOSPEAK emerged de novo in an ancestor of extant primates across a 540 kb region of the genome with a pre-existing highly conserved long-range laryngeal enhancer for a neighbouring bone morphogenetic protein gene GDF6. We used transgenic mouse modelling to identify two additional GDF6 long-range enhancers within TOSPEAK that regulate GDF6 expression in the wrist. Disruption of TOSPEAK in the affected family blocked the transcription of TOSPEAK across the 3 GDF6 enhancers in association with a reduction in GDF6 expression and retrograde development of the larynx and wrist. Furthermore, we describe how TOSPEAK developed a human-specific promoter through the expansion of a penta-nucleotide direct repeat that first emerged de novo in the promoter of TOSPEAK in gibbon. This repeat subsequently expanded incrementally in higher hominids to form an overlapping series of Sp1/KLF transcription factor consensus binding sites in human that correlated with incremental increases in the promoter strength of TOSPEAK with human having the strongest promoter. Our research indicates a dual evolutionary role for the incremental increases in TOSPEAK transcriptional interference of GDF6 enhancers in the incremental evolutionary development of the wrist and larynx in hominids and the human capacity to speak and their retrogression with the reduction of TOSPEAK transcription in the affected family. Full article

In a warming Arctic, permafrost-related disturbances, such as retrogressive thaw slumps (RTS), are becoming more abundant and dynamic, with serious implications for permafrost stability and bio-geochemical cycles on local to regional scales. Despite recent advances in the field of earth observation, many of these have remained undetected as RTS are highly dynamic, small, and scattered across the remote permafrost region. Here, we assessed the potential strengths and limitations of using deep learning for the automatic segmentation of RTS using PlanetScope satellite imagery, ArcticDEM and auxiliary datasets. We analyzed the transferability and potential for pan-Arctic upscaling and regional cross-validation, with independent training and validation regions, in six different thaw slump-affected regions in Canada and Russia. We further tested state-of-the-art model architectures (UNet, UNet++, DeepLabv3) and encoder networks to find optimal model configurations for potential upscaling to continental scales. The best deep learning models achieved mixed results from good to very good agreement in four of the six regions (maxIoU: 0.39 to 0.58; Lena River, Horton Delta, Herschel Island, Kolguev Island), while they failed in two regions (Banks Island, Tuktoyaktuk). Of the tested architectures, UNet++ performed the best. The large variance in regional performance highlights the requirement for a sufficient quantity, quality and spatial variability in the training data used for segmenting RTS across diverse permafrost landscapes, in varying environmental conditions. With our highly automated and configurable workflow, we see great potential for the transfer to active RTS clusters (e.g., Peel Plateau) and upscaling to much larger regions. Full article

A major challenge in processing 7xxx series aluminum alloys is their limited formability at room temperature. In this paper, for the alloys EN AW-7020 and EN AW-7075, various variants of the W-temper forming process are investigated. For both alloys, a good cold formability and a high strength after aging can be achieved. The effects of solution heat treatment or retrogression temperature and holding time, as well as the influence of plastic deformation after quenching, were studied. For various combinations of process parameters, the formability of the as-quenched materials and the hardening performance during artificial aging were examined. For this, hardness measurements and differential scanning calorimetry (DSC) experiments were performed along the entire process chain, to reveal the development of the hardening precipitates. After solution heat treatment and quenching, the yield stress and hardness of both investigated alloys were drastically reduced in comparison to their initial T6 states, while the ductility was significantly increased. By a subsequent simple artificial aging treatment, the same hardness as in the T6 state could be restored. It was observed that plastic deformation immediately after quenching significantly decreased the artificial aging time to achieve the peak hardness. Besides the conventional solution heat treatment process, an alternative retrogression and re-aging procedure was identified for the alloy EN AW-7020. While the heat treatment temperature can be reduced as compared to the conventional solution heat treatment, the formability and hardenability are equally good. In contrast, no such alternative process could be identified for the alloy EN AW-7075. Full article