Search Results (14)

Radiant cooling has been growing in recent years due to energy savings and improved comfort and health. The aim of this study was to reduce energy consumption and provide comfort using a chilled ceiling panel in the zone. In the experimental part of this study, a test room was created to investigate the change in the heat transfer performance of a chilled ceiling panel according to different water temperatures, different water flow rates and different heat source values. As a result of the experimental study, it was found that optimum conditions were achieved with a heat rate of 280 Watts and the lowest supply water temperature of 14 °C, with indoor comfort conditions being achieved with water flow rates of 0.93 m³/h. In the theoretical part of this study, a thermal balance was established for ceiling panel cooling applications. An analytical model of the heat transfer between the cold ceiling panel and the room air was also developed. The convection coefficient, convective heat transfer and total heat transfer coefficient were compared using the values obtained from the experiments and those reported in the literature. It was found that the convection coefficient was within the range reported in the literature, and the radiation heat coefficient was within 99.8% of the literature values. Full article

The increasing demand for energy-efficient and sustainable solutions in the building sector has driven the need for innovative approaches that integrate renewable energy sources and advanced control systems. This paper presents an integrated energy management solution for solar-powered smart buildings, combining a multifaceted physical system with advanced IoT- and cloud-based control systems. The physical system includes a heat pump, photovoltaics, solar thermal panels, and an innovative low-enthalpy radiant wall and ceiling, providing self-sufficient heating and cooling. The control system makes use of advanced IoT and communication engineering technologies, using Modbus, HTTP, and MQTT protocols for seamless interconnectivity, monitoring, and remote management. The successful implementation of this solution in an average-sized model house in Paris and a deep energy retrofit of a semidetached single-family house in Oviedo, northern Spain, demonstrates increased energy efficiency, improved thermal comfort, and reduced environmental impact compared with conventional alternatives. This study illustrates the potential of integrating solar energy, IoT, and communication technologies into smart buildings, contributing to the global effort to reduce the environmental impact of the building sector. Full article

Researching novel cooling and heating technologies as alternatives to conventional vapor-compression refrigeration cycles has received growing attention in recent years. Thermoelectric (TE) systems rank among promising emerging technologies within this category. This paper presents a comprehensive investigation, utilizing numerical modeling and analysis via COMSOL Multiphysics along with experimental validation, to evaluate the performance of a radiant cooling ceiling panel working on thermoelectric principles. Performance metrics are based on thermal comfort levels within the designed test chamber. The system comprises a rectangular test chamber (~1.2 m × 1.2 m × 1.5 m) with a centrally positioned ceiling panel (dimensions: 0.6 m × 0.6 m × 0.002 m). Four TE modules are attached on top of the ceiling panel, facilitating effective cooling to regulate the ceiling temperature to the desired setpoint. The resultant lower ceiling temperature enables heat exchange within the chamber environment via radiation and convection mechanisms. This study examines the time-dependent variations in mean radiant temperature and operative temperature under natural convection conditions, with comfort level assessment carried out using the PMV method according to ASHRAE Standard 55. An experimental chamber is built to validate the numerical model by performing experiments at various ceiling temperatures. Design challenges are discussed in detail. The results of this investigation offer valuable insights into the anticipated thermal comfort achievable through TE-based radiant cooling systems across various operating conditions. Full article

Mean radiant temperature (MRT) is one of the six primary factors that determine thermal comfort in a given thermal environment. In this study, the average radiant temperature was determined using a calculation method based on the surrounding surface temperatures and view factors. The present study specifically investigated the use of calculated radiant temperature, compared to measured radiant temperature, for predicting the mean vote (PMV) and percentage of dissatisfied (PPD) comfort parameters. The method was validated by the experimental measurements via the black sphere thermometer at five different reference points in a test room, including radiant panels on the ceiling and walls. By using global thermometer measurements, the proposed approach achieved a high degree of compatibility and an accuracy of 0.17 °C, which was the difference between calculated and measured values. The results demonstrated the reliability of the procedure using view factors and surrounding surface temperatures to calculate the radiant temperature in the designated test room; here, a straightforward method for evaluating the thermal conditions of an office room and determining the optimal location of an air temperature sensor in PMV-controlled radiant systems was also proposed. This study contributes to the increasing field of research on thermal comfort and offers knowledge that is beneficial for the design and optimization of indoor environments. Full article

Amid concerns over airflow-induced transmission of the COVID-19 virus in buildings frequented by large numbers of people, such as offices, the necessity for radiant ceiling heating panels has increased. This is due to the concern that the airflows emitted from the convection heating systems installed near the ceiling or windows for winter heating may be a major cause of COVID-19 transmission. In this study, we aim to evaluate thermal comfort under various indoor and outdoor environmental conditions of a building and present the thermal output conditions of the radiant ceiling heating panel that can replace the convection heating system while ensuring comfort in the perimeter zone and handling the heating load. As a result, we were able to present, in a chart format, the thermal output conditions that can secure thermal comfort by analyzing the indoor airflow distribution depending on the surface temperature of the radiant ceiling heating panel, the interior surface temperature of the window, and the influence of internal heat generation. Moreover, through derived empirical formulas, we were able to determine the heating conditions of the panel that can secure the necessary heat dissipation while minimizing discomfort, such as downdrafts, even for indoor and outdoor conditions that were not evaluated in this study. Full article

A suspended open-type ceiling radiant cooling panel (CRCP) has been proposed recently. The main challenge is improving its cooling performance to overcome limitations for extensive use. Therefore, this study aims to optimize the design of CRCPs with curved and segmented structure to enhance heat transfer. A three-dimensional CFD model was developed to investigate the cooling capacity and heat transfer coefficient of the CRCPs installed inside a single enclosed room. Panel structure was determined based on four dependent parameters: the panel curvature width (L, m), the panel curvature radius (r, m), the void distance (d, m) between each panel or panel segment, and the panel coverage area (A_c, m²). The panel surface area (A_s, m²) and the ratio of panel curvature width to radius (L/r) were also examined. A total of 35 designs were compared under 7 different cooling load conditions, and 245 cases were carried out. The results show that the nominal cooling capacity and heat transfer coefficient rise with increasing curvature radius and decreasing curvature width. The void distance plays the most crucial role in influencing cooling performance. It is possible to simultaneously improve cooling performance, achieve uniform temperature distribution, and reduce the number of panels through structure optimization. Full article

Increasing peak power demand implies the increasing significance of energy storage. Technologies that efficiently store heat and cold are also important for increasing the share of renewables and improving the efficiency of heating, ventilation, and air conditioning (HVAC) systems. The present experimental study investigated the dynamic behavior of a room with suspended thermally activated ceiling panels filled with a material containing 60% paraffin. The purpose of the study was to determine the specific cooling power and the total energy supplied to the phase change material (PCM) during regeneration. Convective heat flux density, radiant heat flux density, and the heat transfer coefficient (convective, radiant) at the ceiling surface were calculated. Analysis shows that shifting system activation to use lower temperatures during the night maintains thermal comfort. Full article

Thermoelectric (TE) based cooling and heating systems offer significant advantages over conventional vapor compression systems including no need for refrigeration or major moving parts, high controllability, and scalability. The purpose of the present study is to provide an energy and economic assessment of the performance of a TE-based radiant cooling and heating system for building applications. It is considered that TE modules are integrated in the ceiling to lower/increase the ceiling temperature through the Peltier effect during the hot/cold season to provide thermal comfort for the occupants via radiation and convection. The study explores the possibility of using rooftop PV panels to produce electricity required for the operation of TE modules. An actual office building located in Melbourne, FL, USA is considered for a test study, and the hourly cooling and heating loads of the building are calculated through building energy simulation in eQuest. Various operating conditions, including different input voltages and temperature gradient across TE modules, are considered, and the system is sized to properly address the year-around cooling/heating demand. It is shown that a nominal cooling capacity of 112.8 W and a nominal PV capacity of 31.35 W per unit area of the building is required to achieve the target goal when the system operates at the optimal condition. An economic analysis is also performed, and estimated cost, as well as potential savings, are calculated for each operating condition. The optimal operating condition with minimum cost is selected accordingly. The results demonstrated that the initial cost of the proposed system is considerably higher than conventional heating/cooling systems. However, the system offers other benefits that can potentially make it an attractive option for building cooling/heating applications. Full article

Hospitals require the highest energy demands in non-residential buildings. They provide healthcare 24/7/365 and, at the same time, they ensure indoor air quality, thermal comfort and sterility. However, several studies reveal that high indoor temperatures and low relative humidity (RH) are often perceived in patient rooms during the heating season, suggesting an important energy saving potential. Against this background, radiant ceiling panel (RCP) systems result to be one of the most appropriate solutions as they allow to achieve significant energy savings while providing the highest level of thermal and acoustic comfort, as well as of infection control. In the present study the microclimatic survey of a patient room at Maggiore Hospital in Bologna, Italy, equipped with an air conditioning system integrated with RCP, has reported occupant thermal discomfort. Experimental data were used to calibrate a building model and dynamic building energy simulations were carried out to analyse indoor air temperature, relative humidity, predicted mean vote (PMV) and predicted percentage of dissatisfied (PPD) indexes under different inlet air temperatures, to identify the best design conditions for energy efficiency and thermal comfort improvement. It was found that the highest advantages can be obtained when neutral air is supplied. Full article

The objective of this study is to establish boundary conditions to evaluate the cooling capacity of the Cooling Radiant Ceiling Panel (CRCP) considering the environment of a room equipped with the CRCP. The current study investigated the boundary conditions and derivation techniques from previous studies. Based on the results of the analysis, a heat transfer model was derived for a room fitted with CRCP. In addition, the heat transfer model was used to derive the factors affecting the cooling capacity of the CRCP and each factor was simulated and verified through this model. The effects of these factors on the capacity of the CRCP was established by using various boundary conditions. To verify the validity of the simulation model, the experimental results were compared with the cooling capacity for a specific case. As a result, it was established that even for the same panel, there was a variance in the cooling capacity of the CRCP based on the boundary conditions and that the influence of the surface exposed to the outdoors had more implications. Consequently, this study presents the influence factors to be considered when designing CRCP. Full article

When creating a simulation model to assess the performance of buildings, there is usually a lack of feedback information. Only in the case of measurements of a real building is a direct comparison of the measured values and simulated results possible. Parameter data related to users’ behavior or other events can also be obtained. Their evaluated frequency, magnitude and duration, along with boundary conditions, are crucial for the results. It is clear that none of them can be predicted very accurately. Most of them, however, are needed for computer modeling. In this paper we analyzed the well-defined TRNSYS simulation model of offices equipped with radiant ceiling panels for heating and cooling. The model was based on real case offices and was validated based on measurements for 1 year. The analysis included simulations in order to define what effect the parameters related mainly to users have on the energy use and the indoor air temperatures. The study confirmed that specific human activities influence the annual energy use to a relatively small degree and that their effects often counteract. It also confirmed the even more important fact that although small, these activities can influence the thermal comfort of users. It is believed that despite the fact that this research was based on an analysis of offices equipped with radiant ceiling panels, most of the results could be applied generally. Full article

The hot-wall heat exchanger (HWHE) has been widely used in thermal engineering fields such as ceiling radiant heating/cooling, refrigerator condenser, solar heat collection, and high-temperature heat recovery. However, the numerical simulation normally used for heat transfer prediction in HWHE is usually not as convenient as the analytic solutions in engineering applications. In this paper, a new heat transfer mathematical model of HWHE-based on analytic solutions was developed, which could be much faster to obtain the heat transfer properties of HWHE. The proposed model was validated under four conditions with literature values, which showed that the deviations of heat flux are 2.53%, 0.99%, 2.12%, and 1.96%, indicating its accuracy is satisfied. The model was then used to analyze the thermal property of HWHE. The results show the thermal resistance caused by panel with heat convection and conduction accounts for 96.54% of HWHE thermal resistance, and the thermal resistance caused by heat convection on the surface of panel is 74.43%. The analyzation results also show that adding aluminum foil around pipes could decrease HWHE thermal resistance by 5.11%. Besides, the influence of pipe diameters, pipe distance, pipe heat conductivity, side wall heat conductivity, and convective heat transfer coefficient on the heat transfer performance of HWHE was analyzed. The research in this paper can be used for fast prediction and optimization of heat transfer in HWHE. Full article

The main objective of this study was to develop a thermoelectric heat pump and liquid desiccant system based on a dedicated outdoor air system (THPLD-DOAS). An internally-cooled and -heated liquid desiccant system was used and a thermoelectric heat pump (THP) served as the desiccant cooling and heating energy source for dehumidification and regeneration of the desiccant solution, respectively. In order to investigate the energy-saving potential of the proposed system, its thermal performance and operating energy consumption during the cooling season were compared to those of a conventional dedicated outdoor air system with a ceiling radiant cooling panel system (DOAS-CRCP). Detailed simulations for each system were conducted under hot and humid climatic conditions. Their thermal performance under various room sensible heat factor (RSHF) conditions was evaluated to observe the energy performance, depending on the dehumidification performance, of the liquid desiccant system integrated with the THP. The results showed that the coefficient of performance (COP) of the THP ranged from 0.8 to 1.2 to maintain a sufficient dehumidification rate. The operating energy of the THPLD of the proposed system was 6.6% to 16.0% less than that of the chiller operating energy of a conventional DOAS. Consequently, the proposed system consumed 0.6–23.5% less operating energy compared to the conventional DOAS. Full article

In order to achieve significant savings in energy and an improved level of thermal comfort in retrofitted existing buildings, specific retrofitting concepts that combine new technologies and design need to be developed and implemented. Large radiant surfaces systems are now among the most promising future technologies to be used both in retrofitted and in new low-energy buildings. These kinds of systems have been the topic of several studies dealing with thermal comfort and energy utilization, but some specific issues concerning their possible use in various concepts for retrofitting are still poorly understood. In the present paper, some results of dynamic simulations, with the transient system simulation tool (TRNSYS) model, of the retrofitted offices equipped with radiant ceiling panels are presented and thoroughly analysed. Based on a precise comparison of the results of these simulations with actual measurements in the offices, certain input data for the model were added, so that the model was consequently validated. The model was then applied to the evaluation of various concepts of building envelopes for office retrofitting. By means of dynamic simulations of indoor environment it was possible to determine the benefits and limitations of individual retrofitting concepts. Some specific parameters, which are relevant to these concepts, were also identified. Full article