Search Results (21)

This paper focuses on the sealing failure problem of double-lip seal rings for high-speed ball bearings used in unmanned aerial vehicles. By using ANSYS 2023R1 software, a thermal–stress–wear coupled finite element model was established. Taking the contact pressure and volume loss due to wear as indicators to evaluate sealing performance, this study analyzed the influence of lip seal structural parameters on sealing performance, performed response surface optimization of the seal structure parameters and conducted a comparative test on lip seals before and after optimization. The research results show that the contact pressure at the main lip of the lip seal was the greatest, which was 0.79 MPa, and the volume loss due to wear lip seal was 7.94 × 10⁻⁷ mm³. Optimal sealing performance is achieved when the seal lip inclination angle is 41.68°, the middle width of the lip seal is 0.153 mm, the main lip height is 0.179 mm, the spring center distance is 0.37 mm and the radial interference is 0.0034 mm. After optimization, the grease leakage rate of the sealing ring decreased by 48% compared to before optimization. Full article

Single-lip deep-hole drilling is a key technology for the precision machining of high-temperature nickel-based alloy pore structures in aero engines. However, the intense thermo-mechanical coupling effects during machining can easily lead to surface integrity deterioration, and the correlation mechanism between microstructure and properties remains unclear. By adjusting the spindle speed and feed rate, a series of orthogonal experiments were carried out to study the integrity characteristics of the machined surface, including surface morphology, roughness, work hardening, and subsurface microstructure. The results reveal gradient structural features along radial depth: a dynamic recrystallized layer (RL) at the surface and a plastically deformed layer (PDL) containing high-density subgrains/distorted grains in the subsurface. With the increase in the spindle speed, the recrystallization phenomenon is intensified, the RL ratio of the machined-affected zone (MAZ) is increased, and the surface roughness is reduced to ~0.5 μm. However, excessive heat input will reduce the nanohardness. Low feed rates (<0.012 mm/rev) effectively suppress pit defects, whereas high feed rates (≥0.014 mm/rev) trigger pit density resurgence through shear instability. Progressive material removal rate (MRR) elevation drives concurrent PDL thickness reduction and RL proportion growth. Optimal medium MRR range (280–380 mm³/min) achieves synergistic RL/PDL optimization, reducing machining-affected zone thickness (MAZ < 35 μm) while maintaining fatigue resistance. These findings establish theoretical foundations for balancing efficiency and precision in aerospace high-temperature component manufacturing. Full article

Objective: The objective of this study is to develop a convolutional neural network (CNN) for the automatic detection of soft and hard tissue landmarks and the classification of lip thickness on lateral cephalometric radiographs. Methods: A dataset of 1019 pre-orthodontic lateral cephalograms from patients with diverse malocclusions was utilized. A CNN-based model was trained to automatically detect 22 cephalometric landmarks. Upper and lower lip thicknesses were measured using some of these landmarks, and a pre-trained decision tree model was employed to classify lip thickness into the thin, normal, and thick categories. Results: The mean radial error (MRE) for detecting 22 landmarks was 0.97 ± 0.52 mm. Successful detection rates (SDRs) at threshold distances of 1.00, 1.50, 2.00, 2.50, 3.00, and 4.00 mm were 72.26%, 89.59%, 95.41%, 97.66%, 98.98%, and 99.47%, respectively. For nine soft tissue landmarks, the MRE was 1.08 ± 0.87 mm. Lip thickness classification accuracy was 0.91 ± 0.04 (upper lip) and 0.90 ± 0.04 (lower lip) in females and 0.92 ± 0.03 (upper lip) and 0.88 ± 0.05 (lower lip) in males. The area under the curve (AUC) values for lip thickness were ≥0.97 for all gender–lip combinations. Conclusions: The CNN-based landmark detection model demonstrated high precision, enabling reliable automatic classification of lip thickness using cephalometric radiographs. Full article

This work investigated the ₀Cr₁₆Ni₅Mo₁ stainless steel using laser selective melting (SLM) technology and explored the effect of the tempering temperature on the microstructure and properties. After the tempering treatment, the quenched martensite transformed from a metastable to steady state, and residual austenite was formed. The results indicated that the elongation of the transverse specimen showed an upward trend as the tempering temperature increased, while the elongation of the longitudinal specimen first increased and then decreased. The fracture mode was ductile. There was an obvious fiber, radial, and shear lip zone on the fracture surface of transverse specimens. When the tempering temperature was 650 °C, the shear lip area of the fracture surface was the largest. For longitudinal specimens, there was no obvious zoning on the fracture surface. Full article

This article focuses on the problem of sealing failure in high-speed micro bearings. Based on a thermal-stress coupled finite element model, the distribution of equivalent stress and contact pressure of the sealing ring and the influence of various factors on the sealing performance are analyzed. Based on this, the Latin Hypercube sampling method, Kriging surrogate model and genetic algorithm are used to find the optimal combination of sealing performance. Finally, the accuracy of the model and method is verified through orthogonal experiments. Research has found that the maximum equivalent stress of the seal ring is 0.59234 MPa, and it increases first and then decreases with the increase in lip inclination angle, friction coefficient and radial interference amount, increases with the increase in lubricant temperature, and decreases with the increase in bearing rotation speed. The maximum contact pressure is 0.20433 MPa, and it decreases with the increase in the lip inclination angle, increases first and then decreases with the increase in the friction coefficient, and decreases first and then increases with the increase in the lubricant temperature, bearing rotation speed and radial interference amount. The most significant factor affecting the equivalent stress of the seal ring is the lubricant temperature, and the most significant factor affecting the contact stress is the interference fit amount. When the seal lip inclination angle is 43.99°, the friction coefficient is 0.01 mm, the lubricant temperature is 111.5 °C, the bearing rotation speed is 28,853 rpm and the radial interference amount is 0.04 mm, the sealing performance of the sealing ring is optimal. Full article

In zebrafish, like in mammals, radial glial cells (RGCs) can act as neural progenitors during development and regeneration in adults. However, the heterogeneity of glia subpopulations entails the need for different specific markers of zebrafish glia. Currently, fluorescent protein expression mediated by a regulatory element from the glial fibrillary acidic protein (gfap) gene is used as a prominent glia reporter. We now expand this tool by demonstrating that a regulatory element from the mouse Fatty acid binding protein 7 (Fabp7) gene drives reliable expression in fabp7-expressing zebrafish glial cells. By using three different Fabp7 regulatory element-mediated fluorescent protein reporter strains, we reveal in double transgenic zebrafish that progenitor cells expressing fluorescent proteins driven by the Fabp7 regulatory element give rise to radial glia, oligodendrocyte progenitors, and some neuronal precursors. Furthermore, Bergmann glia represent the almost only glial population of the zebrafish cerebellum (besides a few oligodendrocytes), and the radial glia also remain in the mature cerebellum. Fabp7 regulatory element-mediated reporter protein expression in Bergmann glia progenitors suggests their origin from the ventral cerebellar proliferation zone, the ventricular zone, but not from the dorsally positioned upper rhombic lip. These new Fabp7 reporters will be valuable for functional studies during development and regeneration. Full article

The family Eirenidae is one of the major taxa of the order Leptothecata, comprising approximately 80 species from ten genera. In this study, taxonomic investigations, including morphological observations and molecular 16S phylogenetic analyses, were conducted on unknown Eirenidae specimens collected off the coast of Iwaki, Fukushima Prefecture, eastern Japan, in June 2022. The specimens had the following morphological characteristics: marginal warts and tentacular bulbs with lateral cirri and without adaxial papillae, a mouth with simple lips, four simple radial canals, and eight statocysts common to the genus Eutima. However, this species can be distinguished from other species of Eutima by the number of tentacles, number and shape of marginal warts, position of the gonads, and gastric peduncle length. Moreover, the monophyly of the species was evident in the 16S rRNA phylogenetic tree (as indicated by the high bootstrap value of 100%), thereby supporting the validity of the new species. Based on these results, we describe it as a new species, Eutima onahamaensis, for taxonomic stabilization. We also made detailed observations of the morphology and molecular phylogenetic analyses of one of the species newly recorded in Japan: Eutima diademata. A comparative table of the primary diagnostic characteristics of Eutima has been provided. This study provided taxonomic keys for identifying species in the genus Eutima. Full article

This study describes a novel species of Diploderma (Squamata, Agamidae) from the lower valley of the Dadu River of the Sichuan Province of Western China based on its distinct morphological features and molecular evidence. D. daduense sp. nov. can be distinguished from its congeners by its tympanum concealed; head mainly green-yellow, supplemented by black; skin folds under the nuchal and dorsal crest obviously present in adult males only, its vertebral crest discontinuous between nuchal and dorsal sections with a distinct gap; transverse gular fold present but not obvious in some individuals; gular spot absent in both sexes; dorsolateral stripes green-yellow anteriorly, cyan in the center and blurry off-white posteriorly in adult males, the upper edge of dorsolateral stripes strongly jagged in adult males; no radial stripes around the eyes; inner-lip coloration smoky-white, and the coloration of the tongue and oral cavity as a light-flesh color in life; bright green-yellow transverse stripes on dorsal body in males; black patches are evenly distributed along the vertebral line between the dorsolateral stripes from the neck to the base of the tail in males; beech-brown or gray-brown line along the vertebral line with heart-shaped or diamond-shaped black patches on the dorsal body in females; and supratemporals fewer than four on at least one side. The phylogenetic tree based on mitochondrial ND2 sequences indicates that D. daduense sp. nov. forms an independent clade with strong support 1/100 in ML bootstrap/Bayesian posterior probability and is the sister group to D. splendidum. At the inter-species level, the p-distance is at least 6.95%, further confirming that an independent species had been identified. Our work raises the number of species within the genus Diploderma to 47. Full article

Purpose: Acquired defects of the central face pose significant challenges in achieving acceptable cosmetic and functional outcomes. The site, size, and depth of tissue loss often render local tissues inadequate for the repair of major nasal defects. In this article, we aim to demonstrate the efficacy of radial forearm-free flaps as an ideal choice for various central facial unit reconstructions. Methods: This study encompassed patients treated between 2020 and 2022 who underwent facial reconstruction using radial forearm flaps. These flaps were employed in eleven patients with defects involving the lower lid, nose, upper lip, and lower lip. Additionally, we used osteocutaneous flaps in one patient to reconstruct a right nasal bone defect. In three patients requiring medial and lateral canthal tendon reconstruction in one case and oral sphincter reconstruction in two cases, the palmaris longus tendon was included with the flap. Results: In the majority of cases, we achieved good to excellent aesthetic and functional results. Notably, there were no instances of flap failure or partial necrosis in this series. All patients experienced uneventful healing at the donor site. Conclusions: The radial forearm-free flap stands as an ideal and reliable method for reconstructing various facial defects. It offers efficient and thin-conforming skin coverage. Full article

Synthetic fuels significantly reduce pollutant emissions and the carbon footprint of ICE applications. Among these fuels, oxymethylene dimethyl ethers (OME_X) are an excellent candidate to entirely or partially replace conventional fuels in compression ignition (CI) engines due to their attractive properties. The very low soot particle formation tendency allows the decoupling of the soot-NO_X trade-off in CI engines. In addition, innovative piston geometries have the potential to reduce soot formation inside the cylinder in the late combustion stage. This work aims to analyze the potential of combining OME_X with an innovative piston geometry to reduce soot formation inside the cylinder. In this way, several blends of OME_X-Diesel were tested using a radial-lips bowl geometry and a conventional reentrant bowl. Tests were conducted in an optically accessible engine under simulated EGR conditions, reducing the in-cylinder oxygen content. For this purpose, 2-colour pyrometry and high-speed excited state hydroxyl chemiluminescence techniques were applied to trace the in-cylinder soot formation and oxidation processes. The results confirm that increasing OME_X in Diesel improves the in-cylinder soot reduction under low oxygen conditions for both piston geometries. Moreover, using radial lips bowl geometry significantly improves the soot reduction, from 17% using neat Diesel to 70% less at the highest OME_X quantity studied in this paper. Full article

Background: Heterogeneity regarding dosimetry and reporting of endovenous laser ablation (EVLA) mandates the development of a standardized protocol. This study presents the mid-term results of EVLA with 1940 nm-laser and radial-fibre, supported by a four-zone dosimetry tool. Materials and methods: Four anatomical dosimetry zones for great saphenous veins (GSV) and two for small saphenous veins (SSV) were defined with set power levels. Zone-1G (4 W) extended from the inguinal ligament to the apex of femoral triangle, Zone-2G (4 W) from the apex of femoral triangle to the upper border of patella. Zone-3G (3 W) from the patella to the tibial tuberosity. Zone-4G (2 W) extended from the tibial tuberosity to the ankle. Zone-1S from the sapheno-popliteal junction to the tibial tuberosity. Zone-2S from the tibial tuberosity to the ankle. Power was increased by 1 W for veins >10 mm and decreased by 1 W when fibre sticking was encountered. Pullback-velocity was max. 1 mm/s. Results: A total of 152 consecutive patients (185 procedures) were recruited. Mean follow-up time was 11.9 months. Mean linear endovenous energy density for GSV was Zone-1G:42 J/cm, Zone-2G:33 J/cm, Zone-3G:27 J/cm, Zone-4G:22 J/cm, Zone-1S:34 J/cm, Zone-2S:27 J/cm. Occlusion rates were 98.9% (1-month) and 93.7% (12-months). Complications at 1 M were low, namely laser-induced paraesthesia (LIP) 2.2% and endovenous heat-induced thrombosis (EHIT) 1.6%. Persistent LIP (12 M) was observed in 0.5%. Conclusion: The proposed four-zone guiding tool is a step towards standardizing dosimetry and documentation for EVLA with 1940 nm. This strategy shows good mid-term results with minimal complications. Long-term follow-up and application in further centres are necessary to prove its reproducibility. Such a guiding tool could improve the ability to analyse, compare and review different EVLA wavelengths and fibre types. Full article

(1) Background: The radial forearm flap (RFF) has evolved as the flap of choice for intraoral mucosal reconstructions, providing thin and pliable skin with a safe blood supply. Perforator flaps such as the anterolateral thigh (ALT) flap are increasingly being discussed for the same applications. (2) Methods: Patient history, treatment details, and outcome of 12 patents with moderate to extended defects of the lip and/or nose area that were reconstructed by a folded radial forearm flap were retrospectively evaluated for oncologic and functional outcomes. (3) Results: The mean oncologic and functional follow-up were 21.1 (min. 3.8; max. 83.3) and 31.2 (min. 6; max. 96) months, respectively. All flaps survived without revision. In eight cases, major lip defects were reconstructed by an RFF; in six patients, the palmaris longus tendon was included for lip suspension. The functional results in terms of eating, drinking, and mouth opening were good in five cases, while three patients were graded as fair due to moderate drooling. In seven cases, the major parts of the nose were reconstructed with two good and five fair (nostril constriction in three cases) functional results. (4) Conclusions: The folded RFF remains a unique free flap option for complex three-dimensional lip and nose reconstructions in terms of flexibility, versatility, and robustness. Full article

Lip carcinoma is one of the most frequent conditions affecting the general population. It is among the ten most common neoplasms, but despite advances in research and therapy, its prognosis has not improved in a significant way in the past few years, making it a challenge in the medical research field and in surgical treatment. This study was conducted with the aim of evaluating the available reconstructive surgical options for the treatment of lip carcinomas in order to define which could be the most appropriate technique to achieve satisfying aesthetic and functional outcomes considering hospital resources in the COVID-19 era. Seventeen patients were included in this retrospective study, which took place between January 2019 and April 2021. There were two groups: seven patients who underwent a radial forearm free flap and ten who underwent locoregional flaps. The statistical analysis was performed to evaluate four different endpoints. Surgical length, ICU stay, and hospitalization time were minor for locoregional flaps. There was no statistically significant difference between the two groups when considering post-operative complications. Locoregional flaps have a more aesthetically pleasing result, but from a functional point of view, the results can be superimposable. Both techniques are associated with adequate speech, mouth opening, sealing, and symmetry. Given the impact of the COVID-19 pandemic on the healthcare system, locoregional flaps have been proven to be a good surgical option in the reconstruction of lip defects both in terms of aesthetics and functional outcome. Full article

The optimization of the piston bowl design has been shown to have a great potential for air–fuel mixing improvement, leading to significant fuel consumption and pollutant emissions reductions for diesel engines. With this aim, a conventional re-entrant bowl for a 1.6 L light-duty diesel engine was compared with two innovative piston designs: a stepped-lip bowl and a radial-bumps bowl. The potential benefits of these innovative bowls were assessed through 3D-CFD simulations, featuring a calibrated spray model and detailed chemistry. To analyse the impact of these innovative designs, two different engine operating conditions were scrutinized, corresponding to the rated power and a partial load, respectively. Under the rated power engine operating condition, a start of injection sensitivity was then carried out to assess the optimal spray–wall interaction. Results highlighted that, thanks to optimal injection phasing, faster mixing-controlled combustion could be reached with both the innovative designs. Moreover, the requirements in terms of swirl were also investigated, and a higher swirl ratio was found to be necessary to improve the mixing process, especially for the radial-bumps design. Finally, at part-load operating conditions, different exhaust gas recirculation (EGR) rates were analysed for two injection pressure levels. The stepped-lip and radial-bumps bowls highlighted reduced indicated specific fuel consumption (ISFC) and soot emissions values over different rail pressure levels, guaranteeing NO_x control thanks to the higher EGR tolerance compared with the re-entrant bowl. The results suggested the great potential of the investigated innovative bowls for improving efficiency and reducing emissions, thus paving the way for further possible optimization through the combination of these designs. Full article

Increased temperatures at the sealing interface between the seal and shaft can reduce the working life of a seal through elastomer aging, swelling and increased friction. Degradation of the seal due to increased temperatures can cause pre-mature failure, wear and leakage. There is no such thing as a perfect seal; each application has requirements to cater to the needs of each system. For radial oil seals in helicopter gearboxes, the contact temperatures at the sealing interface are a critical parameter to consider. In this manuscript, investigating the factors that influence the temperatures at the contact interface shed light on the operating parameters that cause an increase in contact temperatures. Four varying shaft coatings are tested against three seal spring loads for a range of sliding velocities between 5–25 ms⁻¹ to reproduce conditions of the gearbox. The study reveals an optimum seal spring of 12 oz, with a circumferential load of 3.34 N for lowest temperatures at the interface. Higher springs of 14 oz and lower springs of 8.5 oz both cause increased temperatures at the interface. Additionally, the need for surface coatings on the shaft is re-enforced through experimental evidence demonstrated by comparing temperatures reached between a plain stainless steel shaft and three surface coated shafts. Chrome plating shafts are undesirable due to the ‘polishing’ in effect they experience. The results of this study build on this by showing that chrome plated shafts have higher temperatures at the interface, aggravating any wear or polishing in of that surface. Contact temperatures with Tungsten carbide and Chrome oxide coatings remain within the expected temperature rise. Lastly, microscopically ‘rougher’ surfaces result in increased temperatures in contrast to surface coatings within the specified range of roughness as provided by DIN 3760/61/ISO 6194. Full article