Search Results (14)

Passive radar has drawn a lot of attention due to its applications across military and civilian sectors. Under this working paradigm, the utilization of antenna arrays is instrumental, as it increases the signal quality and enables precise target positioning. These promising features rely, however, on the precise calibration of the antenna array, as the different hardware components introduce impairments that compromise the beamforming capabilities of the system. We propose a technique that employs a low-power external beacon signal to produce precise information about the target location, avoiding the angular ambiguities present in other solutions in the literature. The experimental results demonstrate the method’s ability to effectively correct the amplitude and phase inconsistencies while compensating for frequency drifts, enabling beamforming capabilities and direction-of-arrival estimation. Among the tested beacon waveforms, the pseudo-random noise-based signals proved the most robust, especially in low-power scenarios. Additionally, the method was validated in a passive radar setup, where it successfully detected a vessel using opportunistic signals. These findings highlight the method’s potential to enhance passive radar performance while maintaining a low probability of detection, a key aspect in military applications, as well as its applicability to civilian purposes, such as infrastructure monitoring, environmental observation, and traffic management. Full article

For a multiuser multiple-input–multiple-output (MIMO) overlay cognitive radio (CR) network, an opportunistic interference alignment (IA) technique has been proposed that allows spectrum sharing between primary users (PUs) and secondary users (SUs) while ensuring zero interference to the PU. The CR system consists of one PU and K SUs where the PU uses space-time water-filling (ST-WF) algorithm to optimize its transmission and in the process, frees up unused eigenmodes that can be exploited by the SU. The SUs make use of an optimal power allocation algorithm to align their transmitted signals in such a way their interference impairs only the PUs unused eigenmodes. Since the SUs optimal power allocation algorithm turns out to be an optimal beamformer with multiple eigen-beams, this work initially proposes combining the diversity gain property of space-time block codes, the zero-forcing function of IA and beamforming to optimize the SUs transmission rates. This proposed solution requires availability of channel state information (CSI), and to eliminate the need for CSI, this work then combines Differential Space-Time Block Coding (DSTBC) scheme with optimal IA precoders (consisting of beamforming and zero-forcing) to maximize the SUs data rates. Simulation results confirm the accuracy of the proposed solution. Full article

Physical-layer security (PLS) has attracted much attention in wireless communications and has been considered one of the main candidates for enhancing wireless security in future 6G networks. Recent studies in the PLS area have focused on investigating and analyzing the characteristics of secure transmissions in multiuser networks (e.g., the massive number of Internet of Things (IoT) devices in 6G networks). Due to the difficulty of obtaining the exact secrecy capacity region in wireless multiuser networks, several alternative methods are used to characterize the secrecy performance of multiuser networks. For example, we can analyze the secrecy sum-rate scaling in terms of the number of users based on multiuser diversity (MUD). In this paper, we propose an opportunistic user scheduling scheme that achieves optimal MUD gain, combined with a power control mechanism for reducing information leakage to multiple eavesdroppers in wireless networks. The proposed scheme considers multiuser transmissions in one scheduling time slot by adopting orthogonal random beamforming at the receiver to exploit the full degrees-of-freedom gain with an assumption that each user (or IoT device) is equipped with a single antenna, and base station and eavesdroppers have multiple antennas. The main contribution of this paper is to derive the analytic result of the achievable secrecy sum-rate scaling in a high signal-to-noise ratio (SNR) regime. We evaluate the performance of the proposed scheduling scheme with a power control mechanism through simulations with both internal and external eavesdropping scenarios. We further discuss the extensibility of our analysis to various applications such as satellite communications and IoT networks. Full article

Reconfigurable intelligent surface-aided communication systems have been intensively investigated to improve capacity, coverage, and energy efficiency via optimal controlling of phase shifts for passive reflecting elements. However, there are few studies on cooperative transmission incorporating RIS in TDMA systems, because RIS reflects all the incident signals, and it inadvertently leads to a boost in interference signals. In this paper, we propose RIS-assisted cooperative time-division multiple access, in which the required SINR of all users is guaranteed as much as possible by opportunistic use of RIS for cooperative transmission. The proposed scheme’s primary function is that some time slots, i.e., cooperative time slots, serve a pair of users, i.e., a strong- and a weak-channel-conditioned user, using RIS. To support this functionality, we propose scheduling for non-cooperative and cooperative time slots, user pairing for scheduled cooperative time slots, and transmit beamforming vector design for the pair of UEs in each cooperative time slot. The simulation and numerical results demonstrate that the proposed scheme guarantees QoS for all UE as much as possible and minimizes the remaining required capacity indicating the amount of capacity that was not achieved compared with the required capacity. Full article

We consider multipath TCP (MPTCP) flows over the data networking dynamics of IEEE 802.11ay for drone surveillance of areas using high-definition video streaming. Mobility-induced handoffs are critical in IEEE 802.11ay (because of the smaller coverage of mmWaves), which adversely affects the performance of such data streaming flows. As a result of the enhanced 802.11ay network events and features (triggered by beamforming, channel bonding, MIMO, mobility-induced handoffs, channel sharing, retransmissions, etc.), the time taken for packets to travel end-to-end in 802.11ay are inherently time-varying. Several fundamental assumptions inherent in stochastic TCP models, including Poisson arrivals of packets, Gaussian process, and parameter certainty, are challenged by the improved data traffic dynamics over IEEE 802.11ay networks. The MPTCP model’s state estimation differs largely from the actual network values. We develop a new data-driven stochastic framework to address current deficiencies of MPTCP models and design a foundational architecture for intelligent multipath scheduling (at the transport layer) considering lower layer (hybrid) beamforming. At the heart of our cross-layer architecture is an intelligent learning agent for actuating and interfacing, which learns from experience optimal packet cloning, scheduling, aggregation, and beamforming using successful features of multi-armed bandits and federated learning. We demonstrate that the proposed framework can estimate and optimize jointly (explore–exploit) and is more practicable for designing the next generation of low-delay and robust MPTCP models. Full article

Passive technologies, including intelligent reflecting surfaces (IRS), are gaining traction thanks to their ability to enhance communication systems while maintaining minimal cost and low complexity. They can assist a wireless sensor network (WSN) by achieving low power requirements for sensors and aid communication needs in many applications, for instance, environmental monitoring. In this paper, we propose an IRS-equipped WSN which describes sensors equipped with IRSs instead of active radio frequency (RF) electronics. The IRS sensor node (ISN) intercepts a dedicated signal from a power source such as a base station (BS) and modulates the transmission of that signal to an intended recipient. In order to enable multiple sensors to transmit to the receiver, we study opportunistic scheduling (OS) utilizing multi-sensor diversity while considering blind IRS operation, and compare it with round-robin (RR), proportional fairness (PF), and a theoretical upper bound. We study the effect of the choice of the number of IRS elements N and number of ISNs L on the average throughput of the system under OS. Finally, we provide pertinent comparisons for the different scheduling schemes and IRS configurations under relevant system performance metrics, highlighting different scenarios in which each scheme performs better. Full article

Opportunistic beamforming (OBF) is a potential technique in the fifth generation (5G) and beyond 5G (B5G) that can boost the performance of communication systems and encourage high user quality of service (QoS) through multi-user selection gain. However, the achievable rate tends to be saturated with the increased number of users, when the number of users is large. To further improve the achievable rate, we proposed a multi-antenna opportunistic beamforming-based relay (MOBR) system, which can achieve both multi-user and multi-relay selection gains. Then, an optimization problem is formulated to maximize the achievable rate. Nevertheless, the optimization problem is a non-deterministic polynomial (NP)-hard problem, and it is difficult to obtain an optimal solution. In order to solve the proposed optimization problem, we divide it into two suboptimal issues and apply a joint iterative algorithm to consider both the suboptimal issues. Our simulation results indicate that the proposed system achieved a higher achievable rate than the conventional OBF systems and outperformed other beamforming schemes with low feedback information. Full article

Opportunistic beamforming (OBF) is an effective technique to improve the spectrum efficiencies (SEs) of multiple-input-multiple-output (MIMO) systems, which can obtain multiuser diversity gains with both low computation complexity and feedback information. To serve multiple users simultaneously, many multiple-access schemes have been researched in OBF. However, for most of the multiple-access schemes, the SEs are not satisfactory. To further improve the SE, this paper proposes a downlink multiuser OBF system, where both orthogonal frequency division multiplexing (OFDM) and non-orthogonal multiple-access (NOMA) methods are applied. The closed-form expressions of the equivalent channels and SE are derived in frequency selective fading channels. Then, an optimization problem is formulated to maximize the SE, although the optimization problem is non-convex and hard to solve. To obtain the solution, we divide the optimization problem into two suboptimal issues, and then a joint iterative algorithm is applied. In the proposed optimization scheme, the subcarrier mapping $\vartheta$, user pairing $k_{n_c}$ and allocated power $P_{k_{n_c}}$ are determined to maximize spectrum efficiency (SE) and reduce bit error ratio (BER). According to numerical results, the proposed method achieves approximately 5 dB gain on both SE and BER, compared to the existing beamforming methods with low feedback information. Moreover, the SE of the proposed method is approximately 2 (bps/Hz) higher than sparse code multiple-access (SCMA), when the number of waiting users and the ratio of transmit power to noise variance are respectively 10 and 20 dB. It is indicated that the proposed scheme can achieve high and low BER with the limited feedback and computation complexity, regardless of the transmit power and the number of waiting users. Full article

The opportunistic exchange of information between vehicles can significantly contribute to reducing the occurrence of accidents and mitigating their damages. However, in urban environments, especially at intersection scenarios, obstacles such as buildings and walls block the line of sight between the transmitter and receiver, reducing the vehicular communication range and thus harming the performance of road safety applications. Furthermore, the sizes of the surrounding vehicles and weather conditions may affect the communication. This makes communications in urban V2V communication scenarios extremely difficult. Since the late notification of vehicles or incidents can lead to the loss of human lives, this paper focuses on improving urban vehicle-to-vehicle (V2V) communications at intersections by using a transmission scheme able of adapting to the surrounding environment. Therefore, we proposed a neuroevolution of augmenting topologies-based adaptive beamforming scheme to control the radiation pattern of an antenna array and thus mitigate the effects generated by shadowing in urban V2V communication at intersection scenarios. This work considered the IEEE 802.11p standard for the physical layer of the vehicular communication link. The results show that our proposal outperformed the isotropic antenna in terms of the communication range and response time, as well as other traditional machine learning approaches, such as genetic algorithms and mutation strategy-based particle swarm optimization. Full article

Unlike the fixed power grid cooperative networks, which are mainly based on the reception reliability parameter while choosing the best relay, the wireless-powered cooperative communication network (WPCCN) and in addition to the reception reliability the transmission requirement consideration is important for relay selection schemes. Hence, enabling efficient transmission techniques that address high attenuation of radio frequency (RF) signals according to the distance without increasing the total transmission power is an open issue worth studying. In this relation, a multiantennas power beacon (PB) that assists wireless-powered cooperative communication network (PB-WPCCN) is studied in this paper. The communication between source and destination is achieved with the aid of multiple relays, where both the source and the multiple relays need to harvest energy from the PB in the first place to enable their transmission functionalities. A novel relay selection scheme is proposed, named as two-round relay selection (2-RRS), where a group of relays that successfully decode the source information is selected in the first round selection. In the second round, the optimal relay is selected to forward the recorded information to the destination. The proposed 2-RRS scheme is compared with two existing relay selection schemes, i.e., partial relay selection (PRS) and opportunistic relay selection (ORS). The analytical closed-form expressions of outage probability and average system throughput are derived and validated by numerical simulation. The comparison results between different relay selection schemes show: (I) The superiority of the proposed 2-RRS scheme as it achieves around 17% better throughput compared to the conventional ORS scheme and 40% better than the PRS scheme, particularly when PB transmit power is 10 dB; (II) The proposed 2-RRS scheme guarantees the lowest outage probability, especially when the PB is equipped with multiantennas and performs beamforming technique; (III) The optimal localisation of the PB between the source and N relays depends on the adopted relay selection scheme; (IV) The exhaustive search of the maximum system throughput value shows that the proposed 2-RRS scheme required shorter energy harvesting time compared to other schemes. The increase in energy harvesting time and number of relays do not necessarily reflect positively on the system throughput performance; hence tradeoffs should be taken into consideration. Full article

In this paper, we propose a novel opportunistic interference alignment technique for spectrum-shared radar and uplink cellular communication systems where both systems are equipped with multiple antennas. In the proposed OIA technique, the radar system sends its signal so that the radar signal is received into interference space at base stations (BSs) of the cellular system, while each uplink user (UE) generates its transmit beamforming vector so that communication signals are received within interference space at the radar receiver. Moreover, to achieve better sum-rate performance of the cellular communication system, the BS selects the UEs which results in sufficiently small interference to other cells for the uplink communication. With the proposed OIA technique, detection performance of the radar system is protected, while the communication system achieves satisfactory sum-rate performance. Through extensive computer simulations, we show that the performances of both radar and communication systems with the proposed technique significantly outperform a conventional null-space projection based spectrum sharing scheme. Full article

Cooperative routing, combining cooperative communication in the physical layer and routing technology in the network layer, is one of the most widely used technologies for improving end-to-end transmission reliability and delay in the wireless multi-hop networks. However, the existing cooperative routing schemes are designed based on an optimal fixed-path routing so that the end-to-end performance is greatly restricted by the low spatial efficiency. To address this problem, in this paper an opportunistic cooperative packet transmission (OCPT) scheme is explored by combining cooperative communication and opportunistic routing. The proposed scheme divides the multi-hop route into multiple virtual multiple-input-multiple-output (MIMO) transmissions. Before each transmission, based on the idea of opportunistic routing, a cluster head (CH) is introduced to determine the multiple transmitters and multiple receivers to form a cluster. Then, the single-hop transmission distance is defined as the metric of forward progress to the destination. Each intra-cluster cooperative packet transmission is formulated as a transmit beamforming optimization problem, and an iterative optimal beamforming policy is proposed to solve the problem and maximize the single-hop transmission distance. CH organizes multiple transmitters to cooperatively transmit packets to multiple receivers with the optimized transmit beamforming vector. Finally, according to the transmission results, the cluster is updated and the new cooperative transmission is started. Iteratively, the transmission lasts until the destination has successfully received the packet. We comprehensively evaluate the OCPT scheme by comparing it with conventional routing schemes. The simulation results demonstrate that the proposed OCPT scheme is effective on shortening the end-to-end transmission delay, increasing the number of successful packet transmissions and improving the packet arrival ratio and transmission efficiency. Full article

In this paper, we propose a pseudo-random beamforming (PRBF) technique for improving physical-layer security (PLS) in multiple input multiple output (MIMO) downlink cellular networks consisting of a legitimate base station (BS), multiple legitimate mobile stations (MSs) and potential eavesdroppers. The legitimate BS can obtain available potential eavesdroppers’ channel state information (CSI), which is registered in an adjacent cell. In the proposed PRBF technique, the legitimate BS pseudo-randomly generates multiple candidates of the transmit beamforming (BF) matrix, in which each transmit BF matrix consists of multiple orthonormal BF vectors and shares BF information with legitimate MSs before data transmission. Each legitimate MS generates receive BF vectors to maximize the receive signal-to-interference-plus-noise (SINR) for all pseudo-randomly generated transmit beams and calculates the corresponding SINR. Then, each legitimate MS sends a single beam index and the corresponding SINR value of the BF vector that maximizes the received SINR for each BF matrix since a single spatial stream is sent to each legitimate MS. Based on the feedback information from legitimate MSs and the CSI from the legitimate BS to eavesdroppers, the legitimate BS selects the optimal transmit BF matrix and the legitimate MSs that maximizes secrecy sum-rate. We also propose a codebook-based opportunistic feedback (CO-FB) strategy to reduce feedback overhead at legitimate MSs. Based on extensive computer simulations, the proposed PRBF with the proposed CO-FB significantly outperforms the conventional random beamforming (RBF) with the conventional opportunistic feedback (O-FB) strategies in terms of secrecy sum-rate and required feedback bits. Full article

Interference alignment (IA) is an innovative wireless transmission strategy that has shown to be a promising technique for achieving optimal capacity scaling of a multiuser interference channel at asymptotically high-signal-to-noise ratio (SNR). Transmitters exploit the availability of multiple signaling dimensions in order to align their mutual interference at the receivers. Most of the research has focused on developing algorithms for determining alignment solutions as well as proving interference alignment’s theoretical ability to achieve the maximum degrees of freedom in a wireless network. Cognitive radio, on the other hand, is a technique used to improve the utilization of the radio spectrum by opportunistically sensing and accessing unused licensed frequency spectrum, without causing harmful interference to the licensed users. With the increased deployment of wireless services, the possibility of detecting unused frequency spectrum becomes diminished. Thus, the concept of introducing interference alignment in cognitive radio has become a very attractive proposition. This paper provides a survey of the implementation of IA in cognitive radio under the main research paradigms, along with a summary and analysis of results under each system model. Full article