Search Results (9)

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with varied applications in solar cells as a transparent front contact, intermediate reflector, back reflector layer, and even tunnel layer for passivating contacts, owing to the easy tailoring of its optical properties. In this work, we systematically investigate the influence of the gas mixture (SiH₄, CO₂, PH₃, and H₂), RF power, and process pressure on the optical, structural, and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high-throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material development using various structural and optical characterization techniques (scanning electron microscopy (SEM), energy dispersive X-ray (EDX), Raman spectroscopy, and spectroscopic ellipsometry) with a focus on the relationship between the material properties and the passivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τ_eff). Furthermore, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8–2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with a τ_eff of up to 4.1 ms (implied open-circuit voltage (iV_oc)~715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films. Full article

Driven by the cost and scarcity of Lithium resources, it is imperative to explore alternative battery chemistries such as those based on Aluminum (Al). One of the key challenges associated with the development of Al-ion batteries is the limited choice of cathode materials. In this work, we explore an open-tunnel framework-based oxide (Mo₃VO_x) as a cathode in an Al-ion battery. The orthorhombic phase of molybdenum vanadium oxide (o-MVO) has been tested previously in Al-ion batteries but has shown poor coulombic efficiency and rapid capacity fade. Our results for o-MVO are consistent with the literature. However, when we explored the trigonal polymorph of MVO (t-MVO), we observe stable cycling performance with much improved coulombic efficiency. At a charge–discharge rate of ~0.4C, a specific capacity of ~190 mAh g⁻¹ was obtained, and at a higher rate of 1C, a specific capacity of ~116 mAh g⁻¹ was achieved. We show that differences in synthesis conditions of t-MVO and o-MVO result in significantly higher residual moisture in o-MVO, which can explain its poor reversibility and coulombic efficiency due to undesirable water interactions with the ionic liquid electrolyte. We also highlight the working mechanism of MVO || AlCl₃–[BMIm]Cl || Al to be different than reported previously. Full article

Experimental and numerical investigations of the instantaneous ablation behavior of laminated carbon fiber-reinforced polymer (CFRP) exposed to an intense continuous-wave (CW) laser in a supersonic wind tunnel are reported. We establish an in situ observation measurement in the experiments to examine the instantaneous ablation behavior. The surface recession depth is calculated by using the Particle Image Velocimetry (PIV) method, taking the ply angle of laminated CFRP as a reference. A coupled thermal-fluid-ablation numerical model incorporating mechanisms of oxidation, sublimation, and thermomechanical erosion is developed to solve the ablation-through problem of multilayer materials. The results show that the laser ablation depth is related to the laser power density, airflow velocity and airflow mode. Thermomechanical erosion is the primary ablation mechanism when the surface temperature is relatively low and the cavity flow mode is a closed cavity flow. When the surface temperature reaches the sublimation of carbon and the airflow mode is transformed to open cavity flow, sublimation plays a dominant role and the ablation rate of thermomechanical erosion gradually decreases. Full article

Low-temperature waste heat in the infrared (IR) wavelength region offers an opportunity to harvest power from waste energy and requires further investigation in order to find efficient conversion techniques. Although grating-coupled metal-oxide-semiconductor (MOS) diode devices offer efficient conversion from low and moderate-temperature thermal sources, the integration of such diodes with a nanoantenna structure has yet to be explored. We propose a bowtie nanoantenna coupled with a p-doped MOS diode for IR to direct current (DC) conversion without any bias voltage at 28.3 THz. The nanoantenna was designed and optimized to provide maximum field enhancement in a 4 nm-thick oxide layer at the resonant frequency. The device was fabricated following the complementary MOS (CMOS) fabrication process and measured in a custom DC and optical characterization setup using a 10.6 μm wavelength CO₂ laser. The results reveal two different types of devices with linear and nonlinear I-V curves having kΩ and MΩ zero-bias resistance, respectively. The linear device generates a micron-level open-circuit voltage (V_oc) with clear polarization dependence from the laser input, but the nonlinear case suffers from a weak noise-like signal. Finally, we analyze two types of devices using thermoelectric and tunneling effects and discuss the future direction of nanoantenna-integrated MOS devices for efficient IR harvesters. Full article

In addition to the different technologies of silicon solar cells in crystalline form, TOPCon solar cells have an exceptionally great efficiency of 26%, accomplished by the manufacturing scale technique for industrialization, and have inordinate cell values of 732.3 mV open-circuit voltage (V_oc) and a fill factor (FF) of 84.3%. The thickness of tunnel oxide, which is less than 2 nm in the TOPCon cell, primarily affects the electrical properties and efficiency of the cell. In this review, various techniques of deposition were utilized for the layer of SiO_x tunnel oxide, such as thermal oxidation, ozone oxidation, chemical oxidation, and plasma-enhanced chemical vapor deposition (PECVD). To monitor the morphology of the surface, configuration of annealing, and rate of acceleration, a tunnel junction structure of oxide through a passivation quality of better V_oc on a wafer of n-type cell might be accomplished. The passivation condition of experiments exposed to rapid thermal processing (RTP) annealing at temperatures more than 900 °C dropped precipitously. A silicon solar cell with TOPCon technology has a front emitter with boron diffusion, a tunnel-SiO_x/n⁺-poly-Si/ SiN_x:H configuration on the back surface, and electrodes on both sides with screen printing technology. The saturation current density (J₀) for such a configuration on a refined face remains at 1.4 fA/cm² and is 3.8 fA/cm² when textured surfaces of the cell are considered, instead of printing with silver contacts. Following the printing of contacts with Ag, the J₀ of the current configuration improves to 50.8 fA/cm² on textured surface of silicon, which is moderately lesser for the metal contact. Tunnel oxide layers were deposited using many methods such as chemical, ozone, thermal, and PECVD oxidation are often utilized to deposit the thin SiO_x layer in TOPCon solar cells. The benefits and downsides of each approach for developing a SiO_x thin layer depend on the experiment. Thin SiO_x layers may be produced using HNO₃:H₂SO₄ at 60 °C. Environmentally safe ozone oxidation may create thermally stable SiO_x layers. Thermal oxidation may build a tunnel oxide layer with low surface recombination velocity (10 cm/s). PECVD oxidation can develop SiO_x on several substrates at once, making it cost-effective. Full article

We report on the tunnel oxide passivated contact (TOPCon) using a crystalline nanostructured silicon-based layer via an experimental and numerical simulation study. The minority carrier lifetime and implied open-circuit voltage reveals an ameliorated passivation property, which gives the motivation to run a simulation. The passivating contact of an ultra-thin silicon oxide (1.2 nm) capped with a plasma enhanced chemical vapor deposition (PECVD) grown 30 nm thick nanocrystalline silicon oxide (nc-SiO_x), provides outstanding passivation properties with low recombination current density (J_o) (~1.1 fA/cm²) at a 950 °C annealing temperature. The existence of a thin silicon oxide layer (SiO₂) at the rear surface with superior quality (low pinhole density, D_ph < 1 × 10⁻⁸ and low interface trap density, D_it ≈ 1 × 10⁸ cm⁻² eV⁻¹), reduces the recombination of the carriers. The start of a small number of transports by pinholes improves the fill factor (FF) up to 83%, reduces the series resistance (Rs) up to 0.5 Ω cm², and also improves the power conversion efficiency (PEC) by up to 27.4%. The TOPCon with a modified nc-SiO_x exhibits a dominant open circuit voltage (V_oc) of 761 mV with a supreme FF of 83%. Our simulation provides an excellent match with the experimental results and supports excellent passivation properties. Overall, our study proposed an ameliorated knowledge about tunnel oxide, doping in the nc-SiO_x layer, and additionally about the surface recombination velocity (SRV) impact on TOPCon solar cells. Full article

NOx is a pervasive pollutant in urban environments. This review assesses the current state of the art of photocatalytic oxidation materials, designed for the abatement of nitrogen oxides (NOx) in the urban environment, and typically, but not exclusively based on titanium dioxide (TiO₂). Field trials with existing commercial materials, such as paints, asphalt and concrete, in a range of environments including street canyons, car parks, tunnels, highways and open streets, are considered in-depth. Lab studies containing the most recent developments in the photocatalytic materials are also summarised, as well as studies investigating the impact of physical parameters on their efficiency. It is concluded that this technology may be useful as a part of the measures used to lower urban air pollution levels, yielding ∼2% NOx removal in the immediate area around the surface, for optimised TiO₂, in some cases, but is not capable of the reported high NOx removal efficiencies >20% in outdoor urban environments, and can in some cases lower air quality by releasing hazardous by-products. However, research into new material is ongoing. The reason for the mixed results in the studies reviewed, and massive range of removal efficiencies reported (from negligible and up to >80%) is mainly the large range of testing practices used. Before deployment in individual environments site-specific testing should be performed, and new standards for lab and field testing should be developed. The longevity of the materials and their potential for producing hazardous by-products should also be considered. Full article

For improving retention characteristics in the NOR flash array, aluminum oxide (Al₂O₃, alumina) is utilized and incorporated as a tunneling layer. The proposed tunneling layers consist of SiO₂/Al₂O₃/SiO₂, which take advantage of higher permittivity and higher bandgap of Al₂O₃ compared to SiO₂ and silicon nitride (Si₃N₄). By adopting the proposed tunneling layers in the NOR flash array, the threshold voltage window after 10 years from programming and erasing (P/E) was improved from 0.57 V to 4.57 V. In order to validate our proposed device structure, it is compared to another stacked-engineered structure with SiO₂/Si₃N₄/SiO₂ tunneling layers through technology computer-aided design (TCAD) simulation. In addition, to verify that our proposed structure is suitable for NOR flash array, disturbance issues are also carefully investigated. As a result, it has been demonstrated that the proposed structure can be successfully applied in NOR flash memory with significant retention improvement. Consequently, the possibility of utilizing HfO₂ as a charge-trapping layer in NOR flash application is opened. Full article

The recent Euro 4 and 5 environmental steps for L-category vehicles (e.g., mopeds, motorcycles) were mainly designed to reduce the emissions of particulate matter and ozone precursors, such as nitrogen oxides and hydrocarbons. However, the corresponding engine, combustion, and aftertreatment improvements will not necessarily reduce the solid particle number (SPN) emissions, suggesting that a SPN regulation may be necessary in the future. At the same time, there are concerns whether the current SPN regulations of passenger cars can be transferred to L-category vehicles. In this study we quantified the errors and uncertainties in emission measurements, focusing on SPN. We summarized the sources of uncertainty related to emission measurements and experimentally quantified the contribution of each uncertainty component to the final results. For this reason, gas analyzers and SPN instruments with lower cut-off sizes of 4 nm, 10 nm, and 23 nm were sampling both from the tailpipe, and from the dilution tunnel having the transfer tube in closed or open configuration (i.e., open at the tailpipe side). The results showed that extracting from the tailpipe 23–28% of the mean total exhaust flow (bleed off) resulted in a 24–31% (for CO₂) and 19–73% (for SPN) underestimation of the emissions measured at the dilution tunnel. Erroneous determination of the exhaust flow rate, especially at cold start, resulted in 2% (for CO₂) and 69–149% (for SPN) underestimation of the tailpipe emissions. Additionally, for SPN, particle losses in the transfer tube with the closed configuration decreased the SPN concentrations around 30%, mainly due to agglomeration at cold start. The main conclusion of this study is that the open configuration (or mixing tee) without any instruments measuring from the tailpipe is associated with better accuracy for mopeds, especially related to SPN measurements. In addition, we demonstrated that for this moped the particle emissions below 23 nm, the lower size currently prescribed in the passenger cars regulation, were as high as those above 23 nm; thus, a lower cut-off size is more appropriate. Full article