Search Results (62)

High-speed and conventional laser cladding technologies were used to prepare Fe-based alloy cladding layers on the surface of 45 steel, compare and analyze the microstructure, microhardness, and phase structure of the two cladding layers, and study and analyze the morphology of the molten pool under the two cladding technologies, as well as the mechanism of evolution of the microstructure of the molten pool during the solidification process. The results show that, compared with the conventional laser melting coating, the grain size of the high-speed laser melting coating is finer, and the cooling rate at the top for conventional laser melting is 5.72 × 10³ K/s, and the cooling rate for high-speed laser melting is 3.53 × 10⁵ K/s. The microhardness of the high-speed laser melting coating has been significantly improved, and the solidification rates at the top for the two types of laser melting are the highest, namely 5.84 mm/s and 24.7 mm/s; the molten pool in conventional laser melting is usually larger and deeper, presenting a wide and deep shape, whereas the high-speed laser molten pool is usually shallower and narrower, with a flatter shape, presenting a comet trail, and the fast-cooling and fast-heating effects of high-speed laser melting are more significant. Full article

Additive Manufacturing (AM) has become a revolutionary technology in manufacturing, attracting considerable attention in industrial applications recently. It allows for intricate fabrication, reduces material waste, offers design flexibility, and has economic implications. Nonetheless, the residual stresses generated during the AM process and their effects on microstructural evolution and material properties continue to pose significant challenges hindering its advancement. This paper investigates the evolution of microstructures, focusing on texture and grain size as influenced by processing parameters. It examines how these factors affect the performance of multi-phase materials, specifically in terms of elastic modulus, Poisson’s ratio, and yield strength, leading to variations in residual stress through analytical simulation. The authors developed a thermal model that considers heat transfer boundaries and the geometry of the molten pool. They simulated grain size by considering the heating and cooling processes, including thermal stress, the Johnson-Mehl-Avrami-Kolmogorov (JMAK) model, and grain refinement. The texture was simulated using the Columnar-to-Equiaxed Transition (CET) model, thermal dynamics, and Bunge calculations. The self-consistency model determines the properties based on the established texture distribution. Finally, both microstructure-affected and non-affected residual stresses were modeled and compared. Two gaps between microstructure-affected residual stress and non-affected analytical models appear at the depths of 0.02 mm and 0.078 mm. The results indicate that controlling process parameters and optimizing microstructures can effectively reduce residual stresses, significantly enhancing the overall performance of AM components. Hence, this work provides a more accurate analytical residual stress model and lays the foundation for better control of residual stress in the AM industry. Full article

Laser cladding (LC) is a promising technique for repairing aluminum alloy components, yet challenges like cracks and uneven surfaces persist due to unstable melt flow and thermal stress. This study employs both fluid flow and stress field models to investigate multi-track LC repair mechanisms. Using a finite volume method (FVM), the dynamic evolution of the molten pool was quantified, revealing a maximum flow velocity of 0.2 m/s, a depth of 0.7 mm, and a width of 4 mm under optimized parameters (1600 W laser power, 600 mm/min scan speed). The model also identified that surface flaws between 300 and 900 μm were fully melted and repaired by a current or adjacent track. Finite element analysis (FEA) showed that multi-layer cladding induced a cumulative thermal stress exceeding 1300 MPa at interlayer interfaces, necessitating ≥ 3 s cooling intervals to mitigate cracking risks. These findings provide critical insights into process optimization, demonstrating that adjusting laser power and scan speed can control molten pool stability and reduce residual stress, thus improving repair quality for aluminum alloys. Full article

The performance of the selective electron beam melting (SEBM) products depends on the SEBM-induced temperature and stress. Here, the thermomechanical finite element simulations are conducted to investigate the dynamic evolution of temperature and the thermal stress of melt pool during the SEBM process of Ti6Al4V alloys under various processing parameters and scanning strategies. The results show that the melt pool undergoes three stages of preheating, melting, and remelting under the influence of adjacent scanning tracks. This complex thermal history drives significant changes in thermal stress within the melt pool. After adjusting the processing parameters, it is found that a low scanning speed and high electron beam energy result in a high temperature gradient and stress in the molten pool. Compared to the electron beam energy, the scanning speed has a more significant impact on temperature and residual stress. For the dual-electron-beam scanning strategy, the coupling thermal effect between electron beams can reduce the temperature gradient of the melt pool, thereby suppressing the formation of columnar crystals. The electron beam energy of 300 W and the scanning speed of 1.5 m/s can be selected under various scanning strategies, which are expected to suppress the formation of coarse and columnar β grains and achieve relatively low residual stress. These results contribute to providing a theoretical basis for selecting optimized process parameters and scanning strategies. Full article

The descaling roll is a critical component in a hot-rolling production line. The operating conditions are significantly impacted by water with high-pressure and dynamic shocks caused by high-temperature steel slab descaling. Roll surfaces often experience wear and corrosion failures. This is attributed to a combination of high temperatures, intense wear, and repeated thermal, mechanical, and fluid stresses. Production costs and efficiency are significantly affected by the replacement of descaling rolls. Practice shows that the use of plasma cladding technology forms high-performance coatings. Conventional metal surface properties can be significantly improved. In this study, a Ni-WC composite coating was prepared on the descaling roll surface by plasma-transferred arc welding (PTAW) technology. The microstructure and phase composition of the welding overlay were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Results show that the WC hard phase added to the molten pool dissolves, and subsequently M₇C₃ and W₂C phases are formed. To further explore the morphological evolution mechanism of the hard phase, numerical simulations were performed using a phase-field method to model M₇C₃ phase precipitation. The evolution from nucleation, rod-like growth, to eutectic structure formation was revealed. Experimental and simulation results show high consistency, validating the established phase-field model. In this study, a theoretical foundation for designing and preparing high-performance coatings is provided. Full article

Laser Powder Bed Fusion (LPBF) enables the efficient production of near-net-shape oxide dispersion-strengthened (ODS) alloys, which possess superior mechanical properties due to oxide nanoparticles (e.g., yttrium oxide, Y-O, and yttrium-titanium oxide, Y-Ti-O) embedded in the alloy matrix. To better understand the precipitation mechanisms of the oxide nanoparticles and predict their size distribution under LPBF conditions, we developed an innovative physics-based multiscale modeling strategy that incorporates multiple computational approaches. These include a finite volume method model (Flow3D) to analyze the temperature field and cooling rate of the melt pool during the LPBF process, a density functional theory model to calculate the binding energy of Y-O particles and the temperature-dependent diffusivities of Y and O in molten 316L stainless steel (SS), and a cluster dynamics model to evaluate the kinetic evolution and size distribution of Y-O nanoparticles in as-fabricated 316L SS ODS alloys. The model-predicted particle sizes exhibit good agreement with experimental measurements across various LPBF process parameters, i.e., laser power (110–220 W) and scanning speed (150–900 mm/s), demonstrating the reliability and predictive power of the modeling approach. The multiscale approach can be used to guide the future design of experimental process parameters to control oxide nanoparticle characteristics in LPBF-manufactured ODS alloys. Additionally, our approach introduces a novel strategy for understanding and modeling the thermodynamics and kinetics of precipitation in high-temperature systems, particularly molten alloys. Full article

The friction stir welding (FSW) process is a unique combination of deformation and high temperature, which provides opportunities to modify microstructures through the adjustment of the processing parameters and is an ideal way to join non-weldable aluminum alloys by avoiding the formation of a molten pool. The 7xxx series heat-treatable aluminum alloys are widely used in the aerospace field as high-performance structural materials. The microstructure evolution and mechanical performance of these alloys are affected by the effects of thermomechanical processing, which provides opportunities to optimize the material properties by controlling microstructural features such as intermetallic constituent particles, dispersoids and nanoscale precipitates. This paper focuses on the basic principles of the thermal and mechanical effects generated during FSW on the evolution of second-phase particles in different zones of the weld. Full article

Laser cladding is an emerging environmentally friendly surface-strengthening technology. During the cladding process, the changes in molten pool temperature and velocity directly affect the solidification process and element distribution. The quantitative revelation of the directional solidification mechanism in the molten pool during the cladding process is crucial for enhancing the quality of the cladding layer. In this study, a multi-field coupling numerical model was developed to simulate the coating process of 316L powder on 45 steel matrices using a disk laser. The instantaneous evolution law of the temperature and flow fields was derived, providing input conditions for simulating microstructure evolution in the molten pool’s paste zone. The behavior characteristics of the molten pool were predicted through numerical simulation, and the microstructure evolution was simulated using the phase field method. The phase field model reveals that dendrite formation in the molten pool follows a sequence of plane crystal growth, cell crystal growth, and columnar crystal growth. The dendrites can undergo splitting to form algal structures under conditions of higher cooling rates and lower temperature gradients. The scanning speed of laser cladding (6 mm/s) has minimal impact on dendrite growth; instead, convection within the molten pool primarily influences dendrite growth and tilt and solute distribution. Full article

In order to explore the influence of laser power on the evolution of molten pool and convective heat transfer of laser cladding Incoloy 926 on stainless steel surface, a three-dimensional thermal fluid multi-field coupled laser cladding numerical model was established in this paper. The variation of latent heat during solid-liquid phase transformation was treated by apparent heat capacity method. The change in the gas–liquid interface was tracked using the mesh growth method in real time. The instantaneous evolution of temperature field and velocity flow field of laser cladding Incoloy 926 on a stainless steel surface under different laser power was discussed. The solidification characteristic parameters of the cladding layer were calculated based on the temperature-time variation curves at different nodes. The mechanism of the impact of laser power on the microstructure of the cladding layer was revealed. The experiment of laser cladding Incoloy 926 on 316L surface was carried out under different laser power. Combined with the numerical simulation results, the effects of laser power on the geometrical morphology, microstructure and element distribution of the cladding layer were compared and analyzed. The results show that with the increase in laser power, the peak temperature and flow velocity of the molten pool surface both increase significantly. The thermal influence of the molten pool center on the edge is enhanced. The temperature gradient, solidification rate, and cooling rate increased gradually. The microstructure parameters (G/R) are relatively small when the laser power is 1000 W. In the experimental range, the dilution rate and wetting angle of the cladding layer both increase with the increase in laser power. When the laser power is 1000 W, the alloying elements of the cladding layer are more evenly distributed and the microstructure is finer. The experimental results are in good agreement with the simulation results. Full article

Direct current (DC) and pulsed DC tungsten inert gas (TIG) additive manufacturing processes were employed to fabricate GH4169 high-temperature alloy specimens. Upon comparing and analysing the two additive manufacturing methods, the evolution of microstructure and mechanical properties of the additively manufactured specimens were discussed. It provided a useful reference for the engineering application of pulsed DC TIG technology. The results showed that the overall forming process of the specimen was relatively stable under the DC TIG additive manufacturing and pulsed DC TIG additive manufacturing processes. The aspect ratio of the deposited layer of the pulsed DC-deposited specimen was relatively low, and the deposited layer of the pulsed DC specimen became flatter, which was conducive to maintaining the stability of the molten pool during the deposition process and improving forming accuracy. The microstructure distribution of the deposited layer from bottom to top was relatively uneven, with columnar dendrites in the bottom layer, cellular crystals in the middle layer, and equiaxed crystals in the top layer. Compared with the DC TIG additive manufacturing of GH4169 high-temperature alloy specimens, the Laves phase of the pulsed DC specimens was significantly reduced, which improved the plasticity and brittleness of the material. Full article

Laser-based direct energy deposition (DED-LB/M) has been a promising option for the surface repair of structural aluminum alloys due to the advantages it offers, including a small heat-affected zone, high forming accuracy, and adjustable deposition materials. However, the unequal powder particle size during powder-based DED-LB/M can cause unstable flow and an uneven material flow rate per unit of time, resulting in defects such as pores, uneven deposition layers, and cracks. This paper presents a multiscale, multiphysics numerical model to investigate the underlying mechanism during the powder-based DED-LB/M surface repair process. First, the worn surfaces of aluminum alloy components with different flaw shapes and sizes were characterized and modeled. The fluid flow of the molten pool during material deposition on the worn surfaces was then investigated using a model that coupled the mesoscale discrete element method (DEM) and the finite volume method (FVM). The effect of flaw size and powder supply quantity on the evolution of the molten pool temperature, morphology, and dynamics was evaluated. The rapid heat transfer and variation in thermal stress during the multilayer DED-LB/M process were further illustrated using a macroscale thermomechanical model. The maximum stress was observed and compared with the yield stress of the adopted material, and no relative sliding was observed between deposited layers and substrate components. Full article

In the selective-laser-melting process, it is difficult to monitor the evolution of the melt pool in real time via experimental methods due to the complexity and fine scale of laser–powder interaction; numerical simulation has become an important technical way to study the selective-laser-melting process. A coupled thermal–fluid model of the SLM single-layer melt-channel-forming process is constructed based on hydrodynamic theory for AlSi10Mg metallic materials, and the SLM single-layer melt-channel-forming process is investigated by combining parametric experiments and numerical simulation methods. A binarised spatial-random-function pore material model is proposed, and a multiscale finite-element numerical model of the melt-channel-forming process is constructed to compare and verify the first-layer melt-channel-forming process and to analyse the evolution of the melt pool and the change in the temperature field in multi-layer melt channel formation. The results of this study show that the multiscale numerical model of the SLM multilayer melt-channel-forming process has a reliable computational accuracy, with an average error of 6.77% for the melt pool length and 1.69% for the melt pool width; Marangoni convection effects increase the melt pool size, and the presence of pores significantly affects the evolution of the powder bed temperature field. With laser scanning and powder bed stacking, the overall temperature of the powder bed and the peak temperature of the molten pool gradually increased, and the length, width, and height dimensions of the molten pool increased by 44.9%, 21.7%, and 33.8%, respectively. Full article

This research investigated the relationship between volume energy density and the microstructure, density, and mechanical properties of the Ti-5Al-5Mo-3V-1Cr-1Fe alloy fabricated via the SLM process. The results indicate that an increase in volume energy density can promote a transition from a columnar to an equiaxed grain structure and suppress the anisotropy of mechanical properties. Specifically, at a volume energy density of 83.33 J/mm³, the average aspect ratio of β grains reached 0.77, accompanied by the formation of numerous nano-precipitated phases. Furthermore, the relative density of the alloy initially increased and then decreased as the volume energy density increased. At a volume energy density of 83.33 J/mm³, the relative density reached 99.6%. It is noteworthy that an increase in volume energy density increases the β grain size. Consequently, with a volume energy density of 83.33 J/mm³, the alloy exhibited an average grain size of 63.92 μm, demonstrating optimal performance with a yield strength of 1003.06 MPa and an elongation of 18.16%. This is mainly attributable to the fact that an increase in volume energy density enhances thermal convection within the molten pool, leading to alterations in molten pool morphology and a reduction in temperature gradients within the alloy. The reduction in temperature gradients promotes equiaxed grain transformation and grain refinement by increasing constitutive supercooling at the leading edge of the solid–liquid interface. The evolution of molten pool morphology mainly inhibits columnar grain growth and refines grain by changing the grain growth direction. This study provided a straightforward method for inhibiting anisotropy and enhancing mechanical properties. Full article

In the selective laser melting (SLM) process, adjusting process parameters contributes to achieving the desired molten pool morphology, thereby enhancing the mechanical properties and dimensional accuracy of manufactured components. The parameter window characterizing the relationship between molten pool morphology and process parameters serves as an effective tool to improve SLM’s forming quality. This work established a mesoscale model of the SLM process for a GH3625 alloy based on the discrete element method (DEM) and computational fluid dynamics (CFD) to simulate the forming process of a single molten track. Subsequently, the formation mechanism and evolution process of the molten pool were revealed. The effects of laser power and scanning speed on the molten pool size and molten track morphology were analyzed. Finally, a parameter window was established from the simulation results. The results indicated that reducing the scanning speed and increasing the laser power would lead to an increase in molten pool depth and width, resulting in the formation of an uneven width in the molten track. Moreover, accelerating the scanning speed and decreasing the laser power cause a reduction in molten pool depth and width, causing narrow and discontinuous molten tracks. The accuracy of the simulation was validated by comparing experimental and simulated molten pool sizes. Full article

It remains a popular question whether rare earth oxides encourage reinforcing phases to the uniform distribution in cermet coating to improve the mechanical properties. This study applied laser cladding to prepare the TiAl/WC/CeO₂ MMC cermet coatings on the TC21 alloy substrate. The effects of CeO₂ content on the phase composition, microstructure formation, evolution mechanism, and properties of cermet coatings were investigated. Results show that the incorporation of CeO₂ did not change the phase of composite coating, but the shape of the TiC phase has a close relation to the CeO₂ content. CeO₂ enhanced the fluidity of the molten pool, which further encouraged the TiC/Ti₂AlC core-shell reinforcement phase. With the increase in CeO₂ content, the optimized coating contributed to homogenous microstructure distribution and fine grain size. Owing to the hard phases strengthening and dispersion strengthening effects of CeO₂, the microhardness of the composite coatings was all significantly higher (almost 1.6 times) than that of the substrate. Importantly, the addition of CeO₂ significantly improved the wear resistance of the composite coating. This work provides a certain reference value for the study of surface strengthening of key parts in the aerospace field. Full article