Search Results (1,784)

The Yanshangou landslide, located in the Baihetan Reservoir area, poses severe potential threats to the normal operation of the reservoir due to its distinct deformation characteristics and high sensitivity to reservoir water level fluctuations. This study systematically investigates the geological background, deformation characteristics, stability evolution, and landslide-induced surge hazards of the Yanshangou landslide in the Baihetan Reservoir area. This work only considers the influence of reservoir water level fluctuations, which is the dominant factor controlling the current progressive deformation of the landslide. Field surveys and GNSS/deep displacement monitoring results revealed that the Yanshangou landslide exhibits obvious staged deformation characteristics, and the landslide deformation rate was closely coupled with the dynamic changes in reservoir water level. A slope stability evaluation method integrating the Morgenstern–Price limit equilibrium method and Richard’s equation was established, and the results indicated that the Yanshangou landslide has low saturated permeability. Therefore, its factor of safety (FOS) presents a clear four-stage variation trend in response to reservoir water level fluctuations. A Smoothed Particle Hydrodynamics (SPH)-based numerical model was further developed to simulate the landslide-induced surges under two typical reservoir water level scenarios (815 m and 765 m). The simulation results demonstrated that a high reservoir water level led to more intense surges with greater height and higher velocity, while a low reservoir water level resulted in surges with a wider propagation range along the reservoir bank. The research findings of this study provide a comprehensive theoretical basis and detailed data support for the prevention and mitigation of geological hazards in the Baihetan Reservoir area, and also offer a reference for the hazard management of similar reservoir landslides worldwide. Full article

This study investigates the hydrodynamic characteristics of single-layer heave plates with varying salient edges and triple-layer configurations with size mismatches under forced oscillation, utilizing 3D overset mesh numerical simulations. For single-layer plates, the 0° edge configuration maintains high hydrodynamic coefficients across all conditions, whereas the 135° edge peaks under specific parameters. Introducing horizontal gaps consistently degrades performance. For triple-layer plates, increasing the spacing ratio mitigates spatial flow interference, significantly enhancing hydrodynamic coefficients. Furthermore, introducing size differences creates a stepped mismatched configuration that effectively mitigates wake shielding and enhances fluid entrainment. Consequently, the coefficients increase steadily with the absolute size difference, reaching optimal heave suppression in the triple-layer arrangement with a large spacing and a ±20 m size mismatch. Finally, a highly accurate empirical formula (R² > 0.92) is proposed to predict the damping (C_d) and added mass (C_a) coefficients, effectively capturing the nonlinear coupling effects of spacing ratio and size difference. These findings provide practical theoretical guidance for optimizing vibration reduction systems in offshore platforms. Full article

This study numerically investigates the flow characteristics of submerged impinging jets at a standoff distance of H/d = 3. The computational analysis is performed utilizing large eddy simulation (LES) alongside the one-equation Wray-Agarwal and the two-equation SST k-ω and RNG k-ε turbulence models. The current work emphasizes the hydrodynamic structures developing in the unconfined jet region and the variations in flow behavior at the stagnation zone across a range of impact angles (θ ≤ 90°) at Re (Reynolds number) = 23,400. Compared with PIV data, the Wray-Agarwal model accurately predicts the free-jet flow, whereas the RNG k-ε model excels in the wall-jet region. As the impingement angle increases, the pressure distribution calculated by the LES method gradually approaches the experimental results. When the impinging angle θ = 90°, LES has high prediction accuracy in both regions. In general, under the grid scheme used in this study, RNG k-ε can make a more accurate prediction of the average characteristics of the submerged impinging jet flow field. Full article

The increasing deployment of dense offshore wind turbine monopile foundations pose significant challenges for accurately simulating tidal-flow modification and energy transport at the array scale. Balancing physical realism with computational efficiency remains a key challenge in hydrodynamic modelling of offshore wind farms. In this study, an established drag-based source-term approach is implemented through a dedicated module developed within the TELEMAC-3D framework to represent the momentum-blocking effects of offshore wind-farm arrays. A representative dense 8 × 10 wind turbine monopile array configuration is constructed in a typical tidal channel to systematically examine array-induced tidal-flow responses. The results indicate that the drag-based source-term approach preserves the regional-scale tidal flow structure while effectively capturing array-induced local velocity adjustments and pronounced downstream wake attenuation and recovery. Detailed analyses further reveal distinct spatial and temporal characteristics of the velocity response, including the decay and recovery of velocity deviations downstream of the array. In addition, the monopile array induces a clear modulation of flow kinetic energy, characterized by enhanced energy dissipation and a finite array-scale redistribution of kinetic energy. These findings demonstrate that this approach efficiently simulates the array-scale hydrodynamic and energetic impacts of large offshore wind farms and contribute to a better understanding of array-induced tidal flow modification and energy redistribution. Full article

An integrated analysis incorporating total organic carbon (TOC) content measurement, X-ray diffraction (XRD), scanning electron microscopy (SEM), and gas adsorption experiments was performed on core samples from Well FY1-4 of the upper-fourth Shahejie Formation (Es₄) in the Minfeng Sag. To address the lack of systematic research on the pore and fractal characteristics of organic-rich low-maturity shales in the Minfeng Sag (against the preponderance of studies on high-maturity shales), this study characterized the lithofacies, reservoir space and pore fractal features of the target low-maturity shale interval and clarified the sedimentary controls on lithofacies and key factors regulating pore fractal heterogeneity. The results reveal that the shale in the Es₄ of the study area exhibits low thermal maturity, with six distinct lithofacies identified. Organic-rich laminated calcareous shale lithofacies (RL-1) and organic-rich laminated calcareous/argillaceous mixed shale lithofacies (RL-2) represent the most favorable lithofacies, which are dominated by large mesopores and macropores. Their reservoir spaces were primarily composed of intergranular pores, intragranular pores, and organic pores, whereas the other lithofacies are dominated by small mesopores. The pore surface fractal dimension (D) was calculated using the Frenkel–Halsey–Hill (FHH) model based on low-temperature N₂ adsorption (LTNA) data. The meso-macropore system shows higher heterogeneity than the micropore system (D₂ > D₁). Both D₁ and D₂ exhibit a weak negative correlation with TOC and carbonate content and a positive correlation with clay content. In the initial depositional stage of the Es₄, the arid climate, weak terrigenous input, shallow lake depth, and high salinity resulted in the strongly reducing saline depositional environment with relatively low organic matter enrichment. As the climate became progressively humid in the middle and late stages, hydrodynamic conditions intensified, leading to a lithofacies transition from mixed shales to argillaceous calcareous shales. Increased TOC and carbonate contents reduce the pore fractal dimension of shale. Smaller fractal dimensions directly indicate a simple pore structure and regular pore surface in the shale oil reservoir of the Minfeng Sag, where reservoir space is dominated by large pores such as intercrystalline pores and dissolved pores. Such pore characteristics are more favorable for the enrichment of shale oil. Full article

Background/Objectives: This study addresses the need for scalable and predictive strategies linking mixing conditions to nanocarrier properties by developing and analyzing a coaxial jet antisolvent process for the continuous production of pharmaceutical nanocarriers. Methods: A single experimental platform was used to generate both curcumin-based nanoparticles and nanoliposomes, enabling direct comparison of how mixing regime and formulation variables influence product characteristics. Results: Fluid-dynamic behavior was first characterized using tracer and micromixing experiments, revealing a strong dependence of mixing time on flow conditions, with characteristic mixing times decreasing from >1000 ms under laminar conditions to approximately 10–30 ms in turbulent regimes. Nanoparticles and liposomes obtained under optimized conditions exhibited mean sizes in the range of 120–250 nm, with polydispersity indices typically below 0.2 under optimized turbulent conditions. To rationalize these observations, a computational framework was implemented, combining Reynolds-averaged computational fluid dynamics with a population balance formulation solved by the method of moments. The model provided spatially resolved insight into solvent exchange, supersaturation development, and nucleation–growth dynamics, showing good agreement with experimental trends and capturing the effect of mixing conditions on particle size across different regimes. Conclusions: Although simplified, the modeling approach establishes the basis for future extensions toward full population-balance distribution simulations capable of predicting complete particle size distributions, highlighting the ability of the coaxial jet mixer to control supersaturation and particle formation through tunable hydrodynamic conditions. This capability makes the system particularly attractive compared to conventional batch or less controllable mixing technologies, enabling a more rational and scalable design of pharmaceutical nanocarriers, with good encapsulation performance as discussed in the main text. Full article

In the ElastoHydrodynamic Lubrication (EHL) meshing contact model for rough interfaces with convex–concave textured micro-asperities, the geometric morphology of the meshing interface exhibits pronounced multiscale characteristics: the macroscale manifests as the correlation between Interface-Enriched Lubrication (IEL) performance and meshing Anti-Scuffing Load-Bearing Capacity (ASLBC), while the microscale corresponds to the textured morphology of rough interfaces. In numerical simulations of EHL meshing contact, such cross-scale disparities necessitate solving large-scale systems of analytical solution equations. Assuming periodicity or quasi-periodicity at the microscale, various established methods enable decoupling the macroscopic and microscopic scales, such formalized approaches constitute homogenization theory. However, classical asymptotic assumptions may introduce considerable approximation errors. This study proposes a micro-texture-informed homogenized contact model based on multiscale characterization that incorporates the coupled effects of gear interface meshing forces and thermo-elastic deformations, effectively extending the applicability of classical asymptotic homogenization methods. Full article

A hybrid aquatic–aerial vehicle (HAAV) is a novel type of aircraft capable of both aerial flight and underwater navigation. Inspired by the swan’s gliding and landing motion on water surfaces, this study investigates the dynamic modeling and integrated optimization design of an HAAV equipped with a biomimetic skipping plate. By comprehensively accounting for the aerodynamic, impact, hydrodynamic, and frictional forces during the water entry process, a dynamic model for the HAAV’s gliding water entry is established. The reliability of the model is verified through comparisons between numerical simulations and theoretical predictions. Parametric modeling of the skipping plate’s configuration and layout is performed to analyze the influence of different parameters on the water entry dynamics. With the objectives of minimizing the overload and pitch angle variation, a hybrid infilling strategy based on a radial basis function neural network (RBFNN) surrogate model is constructed to improve optimization efficiency. This is combined with a quantum-behaved particle swarm optimization (QPSO) algorithm to conduct the multi-objective optimization of the biomimetic plate, thereby obtaining its optimal configuration and layout parameters. The results demonstrate that the established dynamic model is effective and can accurately capture the kinematic characteristics of the gliding water entry process. The error between the peak load and the pitch angle variation is less than 5%. Compared with the direct QPSO algorithm, the proposed method reduces the number of model evaluations by 66.7%, the computational time by 52.1%, and the optimal solution response value by 12.01%, demonstrating strong potential for engineering applications. Full article

Granular systems confined in a shallow box and subjected to vertical vibration provide an attractive geometry for studying fluidized granular media. In this configuration, grains acquire kinetic energy in the vertical direction through collisions with the confining walls, and this energy is subsequently transferred to the horizontal degrees of freedom via interparticle collisions. In recent years, the so-called $\mathsf{\Delta }$-model has been introduced as a simplified yet effective description of the dynamics of granular systems in such geometries. This review presents the results obtained from kinetic theory for the granular $\mathsf{\Delta }$-model. To model the energy transfer mechanism, a fixed velocity increment $\mathsf{\Delta }$ is added to the normal component of the relative velocity during collisions. In this way, the vertical motion is effectively integrated out while retaining the collisional energy injection characteristic of the confined setup. This mechanism compensates for the energy loss due to inelastic collisions and leads to stable homogeneous steady states that can be analyzed within the framework of kinetic theory. The Enskog kinetic equation is formulated for this model and first analyzed in homogeneous steady states, yielding the stationary temperature and the equation of state. The dynamics of inhomogeneous states is then investigated using the Chapman–Enskog method, from which the Navier–Stokes transport coefficients are derived. The theory is further extended to granular mixtures, in which particles may differ in mass, size, restitution coefficient, or in the value of $\mathsf{\Delta }$. In this case, the phenomenology becomes richer; for example, energy equipartition is violated even in homogeneous steady states. The mixture dynamics is studied through the corresponding Navier–Stokes equations, and the associated transport coefficients are obtained in the low-density regime. The analysis of the hydrodynamic equations shows that, in agreement with simulations, the homogeneous state is linearly stable. Moreover, the intrinsically nonequilibrium nature of the model leads to the violation of Onsager reciprocity relations in granular mixtures. The theoretical predictions exhibit in general good agreement with both molecular dynamics simulations and direct simulation Monte Carlo results. Full article

To improve the lubrication stability of centrifugal pump mechanical seals under high-speed and high-pressure conditions, a composite texture combining elliptical dimples and herringbone grooves is proposed. The Hybrid Groove–Ellipse (HGE) configuration aims to enhance hydrodynamic pressure generation and mitigate thermal accumulation within the sealing interface. A thermohydrodynamic (THD) lubrication model with cavitation was established, and the coupled governing equations were solved using the finite volume method over 600–6000 rpm and 0.1–1 MPa. The lubrication performance of circular, rectangular, and two elliptical textures was systematically evaluated to identify their hydrodynamic characteristics. The ellipse with major axis parallel to the flow direction exhibited the most favorable pressure distribution and load-carrying capacity. Based on this geometry, the HGE structure was developed. Compared with conventional herringbone grooves, the HGE texture increases local pressure buildup, improves the load-carrying-to-leakage ratio, and modifies cavitation distribution. The maximum interface temperature is reduced by approximately 10–20% under high-speed conditions, with improved temperature uniformity. These results demonstrate that geometric coupling can enhance both the hydrodynamic and thermal performance of mechanical seals. Full article

Friction pairs in wet clutches operate under complex conditions, which can cause surface damage and reduce overall clutch reliability. Surface texturing is an established technique for improving the tribological performance of such mechanical interfaces. Inspired by the wet adhesion properties of tree frog foot pads, a bionic regular hexagonal micro-texture was designed on the mating steel plate. A three-dimensional transient computational fluid dynamics (CFD) numerical methodology was developed and rigorously verified via pin-on-disc friction experiments. Subsequently, this verified numerical framework was extrapolated to establish disc-on-disc CFD models. The results demonstrated that the bionic hexagonal micro-texture altered flow field characteristics, increasing the local maximum flow velocity by 7.9% compared to untextured surfaces. Furthermore, the micro-textured grooves expanded the effective area for convective heat transfer and facilitated local fluid exchange, reducing the maximum average bulk temperature by 20.5% and the maximum radial temperature by 20.7%. Adjusting the structural parameters of these micro-textures further regulated the interfacial flow and temperature fields; notably, deeper grooves induced vortices at land region edges, accelerating flow velocity and decreasing the overall radial temperature gradient. This study provides a theoretical reference for enhancing the thermo-hydrodynamic performance of wet clutch friction pairs. Full article

This article presents a comprehensive assessment of sediment contamination in the Irtysh River within the industrial zone of the city of Ust-Kamenogorsk, using the Specific Combinatorial Sediment Pollution Index (SCSPI). This study includes a set of priority chemical elements characteristic of the region’s technogenic load (Be, Cu, Zn, As, Se, Cd, Te, Hg, Pb), taking into account their hazard class, persistence in bottom sediments, and ability to accumulate in fine-grained (pelitic) fractions. The assessment was carried out based on the calculation of the frequency index of background exceedance (S_α) and the exceedance multiplicity index (S_β), relative to the effective local background value, followed by the determination of the partial pollution indices (Ki) and the integral SCSPI indicator. It was established that, for most elements, the frequency of exceedance ranges from 75% to 100%, indicating widespread surpassing of the effective local background. The partial indices vary within 4–7 points, with cadmium and zinc making the greatest contribution to the formation of integrated pollution due to the presence of local accumulation zones. Correlation analysis showed that the proportion of the pelitic fraction (<0.01 mm) is most strongly associated with the accumulation of Cd (r = 0.67) and Se (r = 0.66), indicating the preferential accumulation of these elements in fine-grained sediments. Principal component analysis revealed stable geochemical associations among the elements. For the <2.0 mm fraction, the first three principal components explain 73.57% of the total variance, with PC1 mainly associated with Pb, Se, and Cd. For the <0.2 mm fraction, the first three components explain 72.44% of the total variance, and PC1 is characterized by high loadings of Zn, Cd, As, and Se, reflecting the strengthening of the technogenic association in fine-grained material. The SCSPI values across the studied cross-sections range from 5.0 to 5.6, corresponding to a moderately polluted state of bottom sediments (Classes 3a–3b). The spatial distribution of the index reflects the combined influence of technogenic sources and hydrodynamic processes responsible for the redistribution of fine-grained material. The obtained results confirm the applicability of the Specific Combinatorial Sediment Pollution Index (SCSPI) for an integrated assessment of the ecological condition of bottom sediments and for identifying zones of increased technogenic load. A comprehensive approach to the analysis of bottom sediment pollution is proposed, enabling a more accurate identification of spatial distribution patterns of contaminants and their accumulation zones. This provides a scientific basis for the development of adaptive strategies for monitoring and management of aquatic ecosystems. This study is of significant practical importance for advancing sustainable environmental management and the rational use of natural resources under increasing anthropogenic impact. Full article

Hydrodynamically triggered landslides remain a major concern in reservoir regions, where the mechanisms controlling displacement evolution are still not fully understood and the multi-scale deformation responses induced by individual hydrodynamic factors remain difficult to quantify. To address these issues, this study establishes a TSD-TET composite framework by integrating time-series signal decomposition with deep learning for multi-scale displacement prediction and the mechanism-oriented interpretation of hydrodynamically triggered landslides. The monitored displacement sequence is first decomposed into physically interpretable components, including trend, periodic, and random terms. Each component is subsequently predicted using deep temporal learning models to capture different deformation characteristics at multiple temporal scales. Meanwhile, key hydrodynamic driving factors, including rainfall, reservoir water level, and groundwater level, are decomposed within the same framework to examine their statistical associations with different displacement components. The proposed approach is applied to the Donglingxin landslide located in the Sanbanxi Hydropower Station reservoir area. Results show that the model achieves high prediction accuracy under both long-term forecasting horizons and limited-sample conditions, with a cumulative displacement coefficient of determination reaching R² = 0.945. Mechanism analysis further indicates that trend deformation is mainly controlled by geological structure and gravitational loading, periodic deformation is strongly modulated by hydrological cycles associated with reservoir water level fluctuations, and random deformation is more likely to reflect short-term disturbances and transient hydrodynamic forcing. These findings provide new insights into the deformation mechanisms of hydrodynamically triggered landslides and offer a promising technical pathway for improving displacement prediction, monitoring, and early warning of reservoir-induced landslide hazards. Full article

The complex surface architecture of natural oyster reefs is widely considered to promote biological attachment, yet the underlying mechanisms and the relevance to the design of artificial reefs are not fully understood. Here, we combined field experiments, 3D surface characterization, and numerical modelling to quantify how reef-like roughness regulates biofouling development and near-wall flow around artificial substrates. Surface morphological characteristics of natural oyster reefs were first obtained by 3D scanning and used to fabricate concrete panels with simulated rough textures, while traditional smooth concrete panels served as controls. The two types of panels were simultaneously deployed in the target sea area for a hanging-panel experiment. Samples were collected after 3, 6, 9, and 12 months to track changes in biofouling communities. At each sampling time, the panel surfaces were quantified by canopy roughness ($R_C$), surface heterogeneity ($\sigma$), and fractal dimension ($D$), and these metrics were integrated into numerical simulations combined to resolve the flow field, turbulence kinetic, and near-wall shear stress around the colonized panels. The research results show that, after 12-month immersion, the mean thickness of the biofouling layer on rough and control panels reached 6.39 mm and 5.91 mm, respectively. Rough panels exhibited consistently higher $R_C$ and $\mathsf{\sigma }$ than controls, and these two parameters are strongly linearly correlated ($R^2=0.891)$. Numerical simulations reveal that increased $R_C$ enlarges the oyster settlement shear-stress window (OSSW), indicating more favorable hydrodynamic conditions for oyster settlement and growth on rough panels. Nevertheless, the hydrodynamic differences between the initial rough panels and control panels gradually diminish over time, suggesting that biological growth can progressively naturalize initially smooth substrates. These findings advance the mechanistic understanding of how small-scale roughness and biofouling co-evolve to shape oyster habitat quality and provide a quantitative basis for the eco-engineering design of artificial oyster reefs. Full article

Zr alloy-shaped charge liners (SCLs) offer broad application prospects due to their multiple post-penetration damage effects. However, research on these liners is still in its early stages. The mechanisms of jet formation and penetration for Zr alloys SCL remain unclear, and the specific contribution of different liner regions to the penetration process is not yet understood. This gap in knowledge has limited their structural design to a black-box correlation between global structural parameters and macroscopic penetration efficiency. To address this gap, a region-tracing Smoothed Particle Hydrodynamics (SPH) simulation was employed. Following a strategy of “wall thickness layering + axial segmentation,” the Zr alloy liner was partitioned into ten characteristic regions. This methodology facilitated the tracking of material transport from each region during jet formation and penetration into an AISI 1045 steel target. The contribution of each region to the penetration depth was then quantitatively assessed via post-processing. For the first time, the “critical region” contributing most to penetration depth was identified, and the influence of the liner’s cone angle and wall thickness on the contribution of each region was revealed. This study enhances the theoretical framework for understanding the damage effects of Zr alloy shaped charge liners. It not only advances the fundamental understanding of jet penetration mechanisms but also provides a theoretical basis for the refined design and performance optimization of these liners. Full article