Search Results (34)

The interest in macromolecular alkoxysilyl-functionalized hybrids (self-assembling or nanostructured), which could be used as precursors in biomimetic silica precipitation and for the synthesis of hollow spherical silica particles, is growing. Nevertheless, reports on all-organosilicon systems for bioinspired silica precipitation are scarce. Therefore, a new kind of polyalkoxysilane macromonomer–linear polysilsesquioxane (LPSQ) of ladder-like backbone, functionalized in side chains with trimethoxysilyl groups (LPSQ-R-Si(OMe)₃), was designed following this approach. It was obtained by photoinitiated thiol-ene addition of 3-mercaptopropyltrimethoxysilane to the vinyl-functionalized polysilsesquioxane precursor, carried out in situ in tetraethoxysilane (TEOS). The mixture of LPSQ-R-Si(OMe)₃ and TEOS (co-monomers) was used in a sol–gel process conducted under acidic conditions (0.5 M HCl/NaCl) in the presence of Pluronic^® F-127 triblock copolymer as a template. LPSQ-R-Si(OMe)₃ played a key role for the formation of microparticles of a spherical shape that were formed under the applied conditions, while their size (as low as 3–4 µm) was controlled by the stirring rate. The hybrid materials were hydrophobic and showed good thermal and oxidative stability. Introduction of zinc acetate (Zn(OAc)₂) as an additive in the sol–gel process influenced the pH of the reaction medium, which resulted in structural reinforcement of the hybrid microparticles owing to more effective condensation of silanol groups and a relative increase of the content of SiO₂. The proposed method shows directions in designing the properties of hybrid materials and can be translated to other silicon–organic polymers and oligomers that could be used to produce hollow silica particles. The established role of various factors (macromonomer structure, pH, and stirring rate) allows for the modulation of particle morphology. Full article

This paper proposes a new functionalized oligosiloxane as a comonomer for polyester, designed to provide hydrophobic surface properties and enhance low-temperature impact resistance. The functionalization of polymer resin itself has attracted attention in the context of monomaterialization. Chemically designing the primary structure of not only polymers but also monomers is crucial for enhancing the intrinsic performance of the resin. However, little is known about oligosiloxane monomers for polyester that can provide oligosiloxane-like properties such as hydrophobicity and flexibility at low temperatures. Here, we report the functional design of a polyester material through silicone copolymerization. A novel comonomer was designed and synthesized to optimize both the molecular structure and the compatibility of the silicone segments, promoting uniform copolymer formation. Incorporating silicone into the polymer matrix reduced surface energy, thereby improving water repellency. Furthermore, the flexibility imparted by the silicone components effectively mitigated the brittleness of polyester at sub-zero temperatures, resulting in superior impact resistance. Structural analysis, contact angle measurements, and low-temperature impact tests were conducted on the copolymers. The results confirmed that optimizing comonomer design enables significant enhancement of both hydrophobicity and impact durability, contributing to the development of high-performance polyester materials suitable for demanding environments. Full article

The functionalization of polymeric matrices through graft polymerization offers multiple advantages by introducing new properties through the incorporation of functional chemical groups on the surface. These modifications can change the chemical properties of the matrix, such as hydrophilicity and chemical reactivity, and enable new chemical interactions with other molecules that the matrix alone could not achieve. This expands the applicability of the material in various fields, particularly in medicine, where these functionalized matrices can be employed as drug delivery systems. In this work, poly(N-vinylpyrrolidone) was incorporated through a graft polymerization of N-vinylpyrrolidone on silicone rubber catheters using gamma radiation to promote the polymerization reaction on the matrix. The graft degree of poly(N-vinylpyrrolidone) on the SR matrix was studied based on the absorbed dose and monomer concentration. Additionally, the new materials were characterized using TGA, wettability kinetics, ATR-FTIR, and Raman spectroscopy, as well as a drug loading evaluation. Full article

Eugenol-containing oligoorganosilsesquioxanes were synthesized by the method of hydrolytic polycondensation in an active medium under various reaction conditions. The obtained products were characterized by ²⁹Si NMR spectroscopy and MALDI-TOF spectrometry. It was shown that factors such as the reaction temperature, polycondensation duration, and molar ratio between the initial alkoxysilane monomer and acetic acid may affect the molecular weight characteristics and molecular structure of the formed oligomer, like the content of stressed cyclic units (T₃, DTT, TDT) and unstressed silsesquioxane units T_nD_m. In particular, an increase in the ratio of the initial reagents led to an increase in the content of silsesquioxane T_n fragments from 28.2%_mol to 41.7%_mol, while the number of strained cyclic structures decreased by more than two times. An increase in the synthesis time is of no particular practical value since it was found that the composition of the oligomers synthesized for 6 h and 12 h was practically identical, as was that of the oligomers synthesized for 24 h and 48 h. A noticeable transition in the oligomer composition was observed only when the synthesis time was changed from 12 h to 24 h. Finally, it was shown that the choice of synthesis temperature had the strongest effect on the oligomer composition. The oligomer synthesized at 95 °C contained the highest amount of silsesquioxane T_n fragments, >77%_mol, while a T_n fragment content of ~42%_mol was observed during the synthesis at 117 °C. It was shown that silsesquioxanes are devitrified at room temperature (T_g from −6.4 to −10.6 °C), and their thermal stability in an inert atmosphere is 300 °C. The synthesized oligomers, due to the presence of hydroxyl-containing eugenol units, may be promising binders and additives for functional epoxy–silicone paints and coating materials. Full article

Optically transparent polyimide (PI) films with good atomic oxygen (AO) resistance have been paid extensive attention as thermal controls, optical substrates for solar cells or other components for low Earth orbit (LEO) space applications. However, for common PI films, it is usually quite difficult to achieve both high optical transparency and AO resistance and maintain the intrinsic thermal stability of the PI films at the same time. In the current work, we aimed to achieve the target by using the copolymerization methodology using the fluorinated dianhydride 9,9-bis(trifluoromethyl)xanthene-2,3,6,7-tetracarboxylic dianhydride (6FCDA), the fluorinated diamine 2,2-bis [4-(4-aminophenoxy)phenyl]hexafluoropropane (BDAF) and the polyhedral oligomeric silsesquioxane (POSS)-containing diamine N-[(heptaisobutyl-POSS)propyl]-3,5-diaminobenzamide (DABA-POSS) as the starting materials. The fluoro-containing monomers were used to endow the PI films with good optical and thermal properties, while the silicon-containing monomer was used to improve the AO resistance of the afforded PI films. Thus, the 6FCDA-based PI copolymers, including 6FCPI-1, 6FCPI-2 and 6FCPI-3, were prepared using a two-step chemical imidization procedure, respectively. For comparison, the analogous PIs, including 6FPI-1, 6FPI-2 and 6FPI-3, were correspondingly developed according to the same procedure except that 6FCDA was replaced by 4,4′-(hexafluoroisopropylidene)diphthalic anhydride (6FDA). Two referenced PI homopolymers were prepared from BDAF and 6FDA (PI-ref1) and 6FCDA (PI-ref2), respectively. The experimental results indicated that a good balance among thermal stability, optical transparency, and AO resistance was achieved by the 6FCDA-PI films. For example, the 6FCDA-PI films exhibited good thermal stability with glass transition temperatures (T_g) up to 297.3 °C, good optical transparency with an optical transmittance at a wavelength of 450 nm (T₄₅₀) higher than 62% and good AO resistance with the erosion yield (E_y) as low as 1.7 × 10⁻²⁵ cm³/atom at an AO irradiation fluence of 5.0 × 10²⁰ atoms/cm². The developed 6FCDA-PI films might find various applications in aerospace as solar sails, thermal control blankets, optical components and other functional materials. Full article

A water-soluble ternary copolymer bearing carboxyl, sulfonic, and amide functional groups was synthesized using ammonium persulfate-catalyzed free radical polymerization in water, resulting in high monomer conversion. This copolymer was then complexed with aluminum sulfate, forming an admixture containing Al(SO₄)(OH)·5H₂O, which was subsequently combined with silica gel. Characterization revealed that the synthesized copolymer formed a large, thin membrane that covered both the aluminum compounds and the silica gel blocks. The introduction of this complex admixture, combining the copolymer and aluminum sulfate, not only reduced the setting times of the cement paste but also enhanced the mechanical strengths of the mortar compared to using aluminum sulfate alone. The complex admixture led to the formation of katoite, metajennite, and C₃A (tricalcium aluminate) in the mortar, demonstrating significant linking effects, whereas pure aluminum sulfate could not completely transform C₃S within 24 h. Further addition of silica gel to the complex admixture further shortened the setting times of the paste, slightly reduced compressive strength, but improved flexural strength compared to the initial complex admixture. The silicon components appeared to fill the micropores and mesopores of the mortar, accelerating cement setting and enhancing flexural strength, while slightly decreasing compressive strength. This study contributed to the development of new cementing accelerators with improved hardening properties. Full article

In this work, we present the modification of a medical-grade silicone catheter with the N-vinylimidazole monomer using the grafting-from method at room temperature and induced by gamma rays. The catheters were modified by varying the monomer concentration (20–100 vol%) and the irradiation dose (20–100 kGy). Unlike the pristine material, the grafted poly(N-vinylimidazole) chains provided the catheter with hydrophilicity and pH response. This change allowed for the functionalization of the catheters to endow it with antimicrobial features. Thus, the quaternization of amines with iodomethane and bromoethane was performed, as well as the immobilization of silver and ampicillin. The inhibitory capacity of these materials, functionalized with antimicrobial agents, was challenged against Escherichia coli and Staphylococcus aureus strains, showing variable results, where loaded ampicillin was amply better at eliminating bacteria. Full article

Molecular imprinting technology is widely used for the specific identification of compounds, but the selective recognition mechanisms of the same compounds still need to be further studied. Based on differences in hydrogen bond size and orientation, molecularly imprinted polymers (MIPs) were designed to adsorb flavonols with the same parent core and different hydroxyl groups. A surface-imprinted material was designed with silicon dioxide as the carrier, myricetin as the template molecule, and methacrylic acid (MAA) as the functional monomer. Scanning electron microscopy (SEM), Brunauer–Emmett–Teller surface area (BET) analyses, Fourier-transform infrared spectroscopy (FT-IR), and other characterization experiments were carried out. The intrinsic mechanism of the MIPs was also explored. The MIPs showed good adsorption of myricetin and other flavonoids through hydrogen bonding and steric hindrance. The adsorption capacity was 3.12–9.04 mg/g, and the imprinting factor was 1.78–3.37. Flavonoids with different hydroxyl groups in different numbers and directions had different hydrogen bond strengths with functional monomers. R₂, R₄, and R₁ on 2-phenylchromogenone had stronger electronegativity, and the hydroxyl group was also more likely to form and have stronger hydrogen bonds. The hydroxyl negativity and the degree of steric hindrance of flavonoids played a major role in the recognition of molecularly imprinted materials. This study is of great significance for the synthesis of and selection of templates for analogous molecular imprinting materials. Full article

Due to growing concerns about environmental pollution from plastic waste, plastic recycling research is gaining momentum. Traditional methods, such as incorporating inorganic particles, increasing cross-linking density with peroxides, and blending with silicone monomers, often improve mechanical properties but reduce flexibility for specific performance requirements. This study focuses on synthesizing silica nanoparticles with vinyl functional groups and evaluating their mechanical performance when used in recycled plastics. Silica precursors, namely sodium silicate and vinyltrimethoxysilane (VTMS), combined with a surfactant, were employed to create pores, increasing silica’s surface area. The early-stage introduction of vinyl functional groups prevented the typical post-synthesis reduction in surface area. Porous silica was produced in varying quantities of VTMS, and the synthesized porous silica nanomaterials were incorporated into recycled polyethylene to induce cross-linking. Despite a decrease in surface area with increasing VTMS content, a significant surface area of 883 m²/g was achieved. In conclusion, porous silica with the right amount of vinyl content exhibited improved mechanical performance, including increased tensile strength, compared to conventional porous silica. This study shows that synthesized porous silica with integrated vinyl functional groups effectively enhances the performance of recycled plastics. Full article

This review covers strategies to prepare high-performance emissive polymer nanomaterials, combining very high brightness and photostability, to respond to the drive for better imaging quality and lower detection limits in fluorescence imaging and sensing applications. The more common approaches to obtaining high-brightness nanomaterials consist of designing polymer nanomaterials carrying a large number of fluorescent dyes, either by attaching the dyes to individual polymer chains or by encapsulating the dyes in nanoparticles. In both cases, the dyes can be covalently linked to the polymer during polymerization (by using monomers functionalized with fluorescent groups), or they can be incorporated post-synthesis, using polymers with reactive groups, or encapsulating the unmodified dyes. Silica nanoparticles in particular, obtained by the condensation polymerization of silicon alcoxides, provide highly crosslinked environments that protect the dyes from photodegradation and offer excellent chemical modification flexibility. An alternative and less explored strategy is to increase the brightness of each individual dye. This can be achieved by using nanostructures that couple dyes to plasmonic nanoparticles so that the plasmon resonance can act as an electromagnetic field concentrator to increase the dye excitation efficiency and/or interact with the dye to increase its emission quantum yield. Full article

UV debonding acrylate adhesive (UDAA) plays a crucial role in the semiconductor industry, where its excellent adhesion is required to ensure the stability of silicon wafers and leave no residue on the surface after UV irradiation. The necessary UV debonding is achieved through the formation of rigid networks by the reactions of all the vinyl groups in the system. Acrylate copolymers with vinyl groups are typically obtained by the grafting reaction of isocyanate with a side-chain hydroxyl comonomer. However, these grafting reactions easily fail due to early cross-link formation. In this study, we illustrate a straightforward method for preparing UDAA by conducting a postgrafting reaction after one-step mixing of isocyanate functional monomer (IPDI-H) and hydroxyl acrylate copolymers (BA-H), thereby skipping the abovementioned vinyl grafting process. The chemical structures of the synthesized IPDI-H and BA-H were confirmed using Fourier transform infrared spectroscopy (FTIR) and proton nuclear magnetic resonance (¹H-NMR) analysis. Gel permeation chromatography (GPC) was employed to determine their molecular weights, while differential scanning calorimetry (DSC) was used to determine their glass transition temperatures. The postgrafting reactions successfully introduced vinyl groups onto the polyacrylate copolymer chains, resulting in high bonding strength during use and a significant decrease in peeling strength after UV irradiation. Rheological methods, including the three-interval thixotropy test (3ITT) and tack test modes, were employed to characterize a series of acrylate UV debonding adhesives. The recovery percentage of the storage modulus in the 3ITT mode indicated that a 0.6 wt% isocyanate curing agent made the UV debonding adhesives resistant to deformation. From the maximum normal force in the tack test mode, it was found that UDAA with 10 wt% PETA monomer and 30 wt% C5 tackifying resin exhibited excellent combined adhesion and debonding properties, which were further confirmed by peel strength tests. Microscope images of the wafer surfaces after removing the adhesive tapes demonstrated the excellent UV debonding properties achieved after 40 s of UV irradiation through the postgrafting reaction. The prepared UDAA has excellent properties; the peel strength can reach 15 N/25 mm before UV irradiation and can be reduced to 0.5 N/25 mm after ultraviolet irradiation. This research establishes a comprehensive method for understanding and applying UDAA in various applications. Full article

In this study, α-Trimethylsilylmethyl-ω-dimethylsilyl-terminated polydimethylsiloxane, polydiethylsiloxane and poly[2,2,2-trifluoropropyl(methyl)siloxane] are synthesized using an anion catalyzed nonequilibrium polymerization reaction with trimethylsilylmethyl lithium as the initiator; hexamethylcyclotrisiloxane, hexaethylcyclotrisiloxane or 1,3,5-trimethyl-1,3,5-trifluoropropylcyclotrisiloxane as the monomer; and dimethylchlorosilane as an end-capping agent. Three kinds of α-trimethylsilylmethyl-ω-trimethoxylsilylethyl-terminated polysiloxanes are further prepared by hydrosilylation reaction of α-trimethylsilylmethyl-ω-dimethylsilyl-terminated polysiloxanes with vinyltrimethoxysilane using Karstedt’s catalyst. These α-trimethylsilylmethyl-ω-trimethoxylsilylethyl-terminated polysiloxanes are functionalized as in situ surface treatment agents for AlN particles. The effects of the structure of these polysiloxanes on the dispersion of AlN in the polysiloxane matrix and on the heat transfer performance of silicone pastes and silicone rubbers are investigated. A possible mechanism of surface treatment of AlN fillers by these novel silicone fluids is also discussed. Full article

Based on the excellent physical properties and flexible molecular modifiability, modified silicone resins have received favorable attention in the field of microelectronics, and recently a number of modified silicone resins have appeared while few breakthroughs have been made in low dielectric constant (low-k) materials field due to the limitations of structure or the curing process. In this work, functional silicone resin with different BCB contents was prepared with two monomers. The resins showed low dielectric constant (k = 2.77 at 10 MHz) and thermal stability (T_5% = 495.0 °C) after curing. Significant performance changes were observed with the increase in BCB structural units, and the functional silicone obtained does not require melting and dissolution during processing because of good fluidity at room temperature. Moreover, the mechanical properties of silicone resins can be also controlled by adjusting the BCB content. The obtained silicone resins could be potentially used in the field of electronic packaging materials. Full article

In the field of flexible electronics manufacturing, inkjet printing technology is a research hotspot, and it is key to developing low-temperature curing conductive inks that meet printing requirements and have suitable functions. Herein, methylphenylamino silicon oil (N75) and epoxy-modified silicon oil (SE35) were successfully synthesized through functional silicon monomers, and they were used to prepare silicone resin 1030H with nano SiO₂. 1030H silicone resin was used as the resin binder for silver conductive ink. The silver conductive ink we prepared with 1030H has good dispersion performance with a particle size of 50–100 nm, as well as good storage stability and excellent adhesion. Additionally, the printing performance and conductivity of the silver conductive ink prepared with n,n-dimethylformamide (DMF): proprylene glycol monomethyl ether (PM) (1:1) as solvent are better than those of the silver conductive ink prepared by DMF and PM solvent. Cured at a low temperature of 160 °C, the resistivity of 1030H-Ag-82%-3 conductive ink is 6.87 × 10⁻⁶ Ω·m, and that of 1030H-Ag-92%-3 conductive ink is 0.564 × 10⁻⁶ Ω·m, so the low-temperature curing silver conductive ink has high conductivity. The low-temperature curing silver conductive ink we prepared meets the printing requirements and has potential for practical applications. Full article

Epilepsy is a neurological disorder that affects millions of people worldwide. Anti-epileptic drugs (AEDs) are critical for their management. However, the therapeutic window is narrow, and traditional laboratory-based therapeutic drug monitoring (TDM) methods can be time consuming and unsuitable for point-of-care testing. To address this issue, we developed a disposable sensor chip based on molecularly imprinted polymer-modified carbon paste electrodes (MIP-CPs) for the TDM of AEDs such as phenobarbital (PB), carbamazepine (CBZ), and levetiracetam (LEV). In this work, functional monomers (methacrylic acid) and crosslinking monomers (methylene bisacrylamide and ethylene glycol dimethacrylate) were copolymerized in the presence of the AED template and grafted on the graphite particles by simple radical photopolymerization. The grafted particles were mixed with silicon oil, dissolving ferrocene as a redox marker to make the MIP-carbon paste (CP). Disposable sensor chips were fabricated by packing the MIP-CP into the base made of poly (ethylene glycol terephthalate) (PET) film. The sensor’s sensitivity was determined using differential pulse voltammetry (DPV), carried out on a single sensor chip for each operation. Linearity was obtained from 0–60 μg/mL in PB and LEV and 0–12 μg/mL in CBZ, covering their respective therapeutic range. The time taken for each measurement was around 2 min. The experiment using whole bovine blood and bovine plasma indicated that the existence of species that interfered had a negligible effect on the test’s sensitivity. This disposable MIP sensor provides a promising approach for point-of-care testing and facilitating the management of epilepsy. Compared with existing tests, this sensor offers a faster and more accurate way to monitor AEDs, which is crucial for optimizing therapy and improving patient outcomes. Overall, the proposed disposable sensor chip based on MIP-CPs represents a significant advancement in AED monitoring, with the potential for rapid, accurate, and convenient point-of-care testing. Full article