Search Results (16)

The escalating industrial emissions have dramatically increased airborne particulate matter (PM), particularly submicron particles (PM0.3), creating substantial health risks through respiratory system penetration. Current fiber-based filtration systems predominantly relying on electrostatic adsorption mechanisms suffer from critical limitations, including insufficient efficiency, potential secondary contamination, and performance degradation in humid environments. We develop a flexible silica composite aerogel to overcome these challenges with customizable and exceptional superamphiphobicity. This composite aerogel exhibits high porosity of ~95% and robust compression Young’s modulus that reaches ~220 kPa at 50% strain even after 1000 cycles. These features enable it to maintain a high filtration efficiency of ~98.52% for PM0.3, even after 50 cycles under traditional artificial simulation conditions. Significantly, a competitive filtration efficiency of ~97.9% is still performed in our composite aerogel at high humidity (water mist), high temperatures (50–250 °C), and corrosive solutions or atmospheres environments, revealing potential industrial applications. This work is expected to replace conventional air filtration materials and pave the way for various human protection and industrial production applications. Full article

A new series of flexible polyamide (PA) aerogels was synthesized using terephthaloyl chloride (TPC), 2,2′-dimethylbenzidine (DMBZ) and cross-linked with an inexpensive, commercially available tri-isocyanate (Desmodur N3300A) at polymer concentrations of 6–8 wt.% total solids and repeating units, n, from 30 to 60. The cross-linked DMBZ-based polyamide aerogels obtained, after supercritically drying using liquid CO₂, had shrinkages of 19–27% with densities ranging from 0.12 g/cm³ to 0.22 g/cm³, porosity and surface areas up to 91% and 309 m²/g, respectively, and modulus values ranging from 20.6 to 109 MPa. Evidence suggests that a higher flexibility could be achieved using DMBZ in the polyamide backbone with N3300A as a cross-linker, when compared to previously reported TPC-mPDA-BTC PA aerogels, N3300A-polyimide aerogels, and N3300-reinforced silica aerogels. Full article

The Applications of silica aerogel are limited due to its brittleness and low strength. As a result, it is essential to strengthen and toughen it. Organic nanofibers are one of the preferred reinforcement materials. In this work, we designed and fabricated flexible and compressible nanostructure-assembled aramid nanofiber/silica composites aerogel (ANF/SiO₂ aerogel) to improve the mechanical strength and flexibility of silica aerogel without compromising thermal insulation properties. The aramid nanofiber/silica composite aerogels were prepared by immersing the aramid nanofiber wet gel into the silica sol for a certain period of time followed by freeze drying without solvent replacement. The surface modifier 3-aminopropyltriethoxysilane (APTES) was used as a coupling agent to form chemical linkage between the ANF fiber and silica gel. It was observed that APTES can effectively drive the silica sol to infuse into ANF hydrogel, promoting the assembly of silica gel onto the fiber surface and a uniform distribution in the network of ANF. The compressive resilience, thermal stability, and thermal insulation properties of the composite aerogels were evaluated by inducing the silica aerogel into the ANF network to form a protective layer on the fiber and change the pore structure in the ANF network. Full article

Using silica as the precursor, and methyltrimethoxysilane and dimethyldimethoxysilane as the silicon sources, a super-flexible hydrophobic lipophilic gel solid was prepared via hydrolysis, drying, solvent replacement, and atmospheric-pressure drying. The characterization test showed that the sample had good flexibility, hydrophobicity, an amorphous structure, and a hydrophobic contact angle of 137°. Through the adsorption separation experiment, it was concluded that the adsorption separation rate of aerogel to oil substances is related to the viscosity of the oil substances. The hydrophobic and oleophilic properties of flexible silicon aerogel materials can be applied to many aspects, such as crude oil leakage and kitchen waste oil recovery, with broad future development prospects and great research significance. Full article

Research on the development of flexible silica aerogels (FSAs) has been ongoing due to their excellent thermal insulation, low density, and high elasticity. However, the physical properties of FSAs, such as density, thermal conductivity, mechanical strength, and surface wettability, are highly dependent on the preparation conditions. To achieve the desired properties of FSAs for various applications, it is necessary to develop a method to fine-tune their physical properties. In this paper, two modifiers of methyltrimethoxysilane (MTMS)/trimethylethoxysilane (TMES) were employed to fine-tune the bulk density of a series of flexible silica aerogels (FSAs), reflecting a series of FSAs with fine-tunable physical properties. First, the precursor was synthesized by a click reaction between vinyltrimethoxysilane (VTMS) and 2,2′ (ethylenedioxy) diethanethiol (EDDET). The VTMS, EDDET, and the as-prepared precursor were characterized by FT-IR and NMR spectroscopy. Subsequently, the precursor was converted into a series of FSAs (denoted by FSA, FSA-M, and FSA-T) through conventional sol-gel reactions with/without MTMS/TMES. Chemical structures of synthesized FSAs were confirmed by ¹³C and ²⁹Si solid-state NMR spectroscopy. The porous structure of FSAs was identified by BET and SEM, respectively. Physical properties, such as thermal conductivity, mechanical strength, and surface wettability of FSAs were determined by a Hot Disk, durometer/DMA in compression mode, and contact angle measurements, respectively. This study found FSAs containing none, 1 wt%, 5 wt%, and 10 wt% of MTMS increase the density of FSAs from 0.419 g/cm³ (FSA), 0.423 g/cm³ (FSA-M1), 0.448 g/cm³ (FSA-M5), and 0.456 g/cm³ (FSA-M10). It should be noted that the thermal conductivity, surface hardness, bulk mechanical strength, and hydrophobicity of FSA-Ms of increasing MTMS loading were all found to show a rising trend, while FSA-Ts exhibited lower density. FSA-T10 exhibited lower thermal conductivity, surface hardness, and bulk mechanical strength as compared to FSA. However, it was found to show higher hydrophobicity as compared to that of FSA. Full article

The reliable characterization of insulation materials in relevant environmental conditions is crucial, since it strongly influences the performance (e.g., thermal) of building elements. In fact, their properties may vary with the moisture content, temperature, ageing degradation, etc. Therefore, in this work, the thermomechanical behaviour of different materials was compared when subjected to accelerated ageing. Insulation materials that use recycled rubber in their composition were studied, along with others for comparison: heat-pressed rubber, rubber_cork composites, aerogel_rubber composite (developed by the authors), silica aerogel, and extruded polystyrene. The ageing cycles comprised dry-heat, humid-heat, and cold conditions as the stages, during cycles of 3 and 6 weeks. The materials’ properties after ageing were compared with the initial values. Aerogel-based materials showed superinsulation behaviour and good flexibility due to their very high porosity and reinforcement with fibres. Extruded polystyrene also had a low thermal conductivity but exhibited permanent deformation under compression. In general, the ageing conditions led to a very slight increase in the thermal conductivity, which vanished after drying of the samples in an oven, and to a decrease in Young’s moduli. Full article

The application of silica aerogel has been limited because of its poor mechanical properties. In order to expand the application scope of silica aerogel, this study fabricated an ultra-flexible conductive silica aerogel as a multiparameter sensor. The sample is fabricated by introducing poly (3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) on a base of ultra-flexible silica aerogel, which was prepared by a diene synthesis reaction at atmospheric pressure. The pressure, temperature, and humidity can be converted into electrical signals. The pressure sensitivity can reach up to 54.88 kPa⁻¹, and the detection limit is as low as 5 Pa. The temperature resolution is up to 0.1 K, and the response time of humidity is within 4 s. More importantly, the developed multiparameter sensor can be self-powered to realize multiparameter sensing of pressure, temperature, and humidity. The ultra-flexible conductive silica aerogel is a promising candidate for monitoring human activities and fire-affected areas. Full article

Flame-retardant, thermal insulation, mechanically robust, and comprehensive protection against extreme environmental threats aerogels are highly desirable for protective equipment. Herein, inspired by the core (organic)-shell (inorganic) structure of lobster antenna, fire-retardant and mechanically robust aramid fibers@silica nanocomposite aerogels with core-shell structures are fabricated via the sol-gel-film transformation and chemical vapor deposition process. The thickness of silica coating can be well-defined and controlled by the CVD time. Aramid fibers@silica nanocomposite aerogels show high heat resistance (530 °C), low thermal conductivity of 0.030 W·m⁻¹·K⁻¹, high tensile strength of 7.5 MPa and good flexibility. More importantly, aramid fibers@silica aerogels have high flame retardancy with limiting oxygen index 36.5. In addition, this material fabricated by the simple preparation process is believed to have potential application value in the field of aerospace or high-temperature thermal protection. Full article

In this work, silica aerogel composites reinforced with reticulated polyurethane (PU) foams have been manufactured having densities in the range from 117 to 266 kg/m³ and porosities between 85.7 and 92.3%. Two different drying processes were employed (ambient pressure drying and supercritical drying) and a surface modification step was applied to some of the silica formulations. These composites, together with the reference PU foam and the monolithic silica aerogels, were fully characterized in terms of their textural properties, mechanical properties and thermal conductivities. The surface modification with hexamethyldisilazane (HMDZ) proved to improve the cohesion between the reticulated foam and the silica aerogels, giving rise to a continuous network of aerogel reinforced by a polyurethane porous structure. The samples dried under supercritical conditions showed the best interaction between matrixes as well as mechanical and insulating properties. These samples present better mechanical properties than the monolithic aerogels having a higher elastic modulus (from 130 to 450 kPa), a really exceptional flexibility and resilience, and the capacity of being deformed without breaking. Moreover, these silica aerogel-polyurethane foam (Sil-PU) composites showed an excellent insulating capacity, reaching thermal conductivities as low as 14 mW/(m·K). Full article

In this work, the novel natural rubber latex (NRL) mixing was approached. The mixing process was carried out by using n-hexane as the dispersed phase of silica aerogel which acted as thermal insulation filler prior to NRL mixing. The silica aerogel/NR composites were prepared with different silica aerogel contents of 20, 40, 60, 80, and 100 parts per hundred rubber (phr). The morphology of the 40 phr composite showed the NR macropore formation with silica aerogel intercalated layers. The optimal content of silica aerogels and n-hexane were the key to obtaining the NR macropore. The thermal insulation performance of silica aerogel/NR composites was investigated because of their porous structures. The thermal conductivity of the composites were lower than that of the neat NR sheet and decreased from 0.081 to 0.055 W m⁻¹·K⁻¹ with increasing silica aerogel content. The lower densities of the composites than that of the NR sheet were revealed noticeably. In addition, the silica aerogel/NR composites exhibited a higher heat retardant ability than that of the NR sheet, and the comparable glass transition temperatures (T_g) of the composites and the neat NR indicated the maintained flexibility at ambient temperature or higher, which can benefit various temperature applications. The overall results demonstrated that the silica aerogel/NR composites from the novel NRL mixing preparation could be a promising technique to develop the porous materials and be utilised as thermal insulation products and building constructions. Full article

The rapid growth of CO₂ emissions in the atmosphere has attracted great attention due to the influence of the greenhouse effect. Aerogels’ application for capturing CO₂ is quite promising owing to their numerous advantages, such as high porosity (~95%); these are predominantly mesoporous (20–50 nm) materials with very high surface area (>800 m²∙g⁻¹). To increase the CO₂ level of aerogels’ uptake capacity and selectivity, active materials have been investigated, such as potassium carbonate, K₂CO₃, amines, and ionic-liquid amino-acid moieties loaded onto the surface of aerogels. The flexibility of the composition and surface chemistry of aerogels can be modified intentionally—indeed, manipulated—for CO₂ capture. Up to now, most research has focused mainly on the synthesis of amine-modified silica aerogels and the evaluation of their CO₂-sorption properties. However, there is no comprehensive study focusing on the effect of different types of aerogels and modification groups on the adsorption of CO₂. In this review, we present, in broad terms, the use of different precursors, as well as modification of synthesis parameters. The present review aims to consider which kind of precursors and modification groups can serve as potentially attractive molecular-design characteristics in promising materials for capturing CO₂. Full article

While traction energy is the main energy used in passenger trains, the energy required to condition the passenger area is significant and can account for up 40% of the total energy use. Due to space constraints, passenger train envelopes are usually only insulated with a few centimetres of conventional insulation materials, leading to relatively high U-values and high energy transmissions in climates where heating or cooling is necessary. Here, the use of superinsulation materials in trains for heating/cooling demand reduction was evaluated. Selected commercially available superinsulation materials were screened and benchmarked in terms of thermal conductivity, fire safety, behaviour under vibration and preferred use position within the train envelope. Both the specific vacuum insulation panels and silica aerogel boards that were tested were found suitable for the application in train envelopes in terms of their thermal, fire and mechanical properties. While vacuum panels have the best insulation performance, aerogel boards offer higher flexibility during installation and reduced risk of damage-related performance loss. Both materials can greatly enhance the energy efficiency and thermal comfort of trains and can be implemented cost-neutrally. However, new policy frameworks are likely to be necessary to promote energy efficiency and the broad implementation of thermal superinsulation in trains. Full article

Bionanocomposites based on poly (lactic acid) (PLA) and silica aerogel (SiA) were developed by means of melt extrusion process. PLA-SiA composite films were plasticized with 15 wt.% of acetyl (tributyl citrate) (ATBC) to facilitate the PLA processability as well as to attain flexible polymeric formulations for films for food packaging purposes. Meanwhile, SiA was added in four different proportions (0.5, 1, 3 and 5 wt.%) to evaluate the ability of SiA to improve the thermal, mechanical, and barrier performance of the bionanocomposites. The mechanical performance, thermal stability as well as the barrier properties against different gases (carbon dioxide, nitrogen, and oxygen) of the bionanocomposites were evaluated. It was observed that the addition of 3 wt.% of SiA to the plasticized PLA-ATBC matrix showed simultaneously an improvement on the thermal stability as well as the mechanical and barrier performance of films. Finally, PLA-SiA film formulations were disintegrated in compost at the lab-scale level. The combination of ATBC and SiA sped up the disintegration of PLA matrix. Thus, the bionanocomposites produced here show great potential as sustainable polymeric formulations with interest in the food packaging sector. Full article

Flexible fibers composed of a conductive material mixed with a polymer matrix are useful in wearable electronic devices. However, the presence of the conductive material often reduces the flexibility of the fiber, while the conductivity may be affected by environmental factors such as water and moisture. To address these issues, we developed a new conductive fiber by mixing carbon nanotubes (CNT) with a polyurethane (PU) matrix. A silane ((heptadecafluoro–1,1,2,2–tetra–hydrodecyl)trichlorosilane) was added to improve the strain value of the fiber from 155% to 228%. Moreover, silica aerogel particles were embedded on the fiber surface to increase the water contact angle (WCA) and minimize the effect of water on the conductivity of the fiber. As a result, the fabricated PU-CNT-silane-aerogel composite microfiber maintained a WCA of ~140° even after heating at 250 °C for 30 min. We expect this method of incorporating silane and aerogel to help the development of conductive fibers with high flexibility that are capable of stable operation in wet or humid environments. Full article

In recent years, flexible silica aerogels have gained significant attention, owing to their excellent thermal and acoustic insulation properties accompanied by mechanical flexibility. Fiber reinforcement of such aerogels results in a further enhancement of the strength and durability of the composite, while retaining the excellent insulation properties. In this paper, the influence of four different kinds of fibers within a flexible silica aerogel matrix is studied and reported. First, a description of the synthesis procedure and the resulting morphology of the four aerogel composites is presented. Their mechanical behavior under uniaxial quasi-static tension and compression is investigated, particularly their performance under uniaxial compression at different temperature conditions (50 °C, 0 °C, and −50 °C). The reinforcement of the flexible silica aerogels with four different fiber types only marginally influences the thermal conductivity but strongly enhances their mechanical properties. Full article