Search Results (12)

This study presents the results of laboratory experiments on the processing of lateritic nickel ores mixed with coal and CaO, followed by the use of the obtained product for the smelting of nickel-containing ferroalloy by the metallothermic method. The study analyzed the thermodynamic effects of complex reductant concentration (silicon- and aluminum-containing alloy) on the reduction degree of nickel and iron. An experimental process resulted in a product containing Ni_total (2.60%) and Fe_total (60.52%), obtained through reduction roasting of lateritic nickel ore mixed with coal and an addition of 20 g of CaO at a temperature of 1150 °C. Under laboratory conditions, a nickel-containing ferroalloy was successfully obtained using the product after reduction roasting and a complex alloy as the reducing agent. The following optimal process parameters were determined: reductant consumption of 20 g per 100 g of the reduction roasting product, smelting temperature of 1600 °C, and slag basicity (CaO/SiO₂) of 0.5. In this case, a nickel-containing ferroalloy with 72% iron, 15% nickel, and up to 5% chromium was successfully obtained through silicon and aluminum reduction using a complex alloy. A microstructural analysis of the nickel-containing alloy was conducted using an electron probe microanalyzer (JXA-8230) in combination with scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). The results showed that silicon and iron were the dominant elements in all particles. Nickel was detected at concentrations of up to 15.02 wt. %, while chromium reached 3.47 wt. %. Depending on the silicon concentration, the nickel-containing ferroalloy is recommended for corrosion-resistant steel production (Si < 5%) and as a reducing agent for ferronickel production (Si > 5%). Full article

In modern nickel mineral processing operations, the aim is to separate pentlandite from gangue minerals. One of these gangue minerals, pyrrhotite, contains up to 1 wt% Ni but is disposed of as waste, i.e., as tailings. Declining sulfide ore grades and increasing nickel demand have led to renewed interest in extracting nickel from pyrrhotite tails. One proposed process is thermal concentration, which aims to recover the nickel as a ferronickel alloy via thermal treatment at temperatures greater than 900 °C. Achieving these temperatures requires substantial energy input as the reactions involved are highly endothermic. In the present research, microwave radiation was used to process a reaction mixture consisting of a concentrate of pyrrhotite tails, iron ore, and metallurgical coke. The fundamental property that determines the interaction of microwaves with a material is complex permittivity. It was found that the reaction mixture had very high real and imaginary permittivities, making it a good candidate for microwave treatment. An input power of 800 W of microwave radiation (2450 MHz) was then employed to heat various reaction mixtures for thermal treatment times of 120, 300, and 600 s. The ferroalloy grades (6–7.5 wt% Ni) were comparable to those produced by conventional heating and to those obtained by other authors using conventional heating techniques. The microwaved samples had increased metallization of nickel, which was attributed to increased melting due to the higher internal temperatures. Full article

Saprolite ores in nickel laterite deposits are pyrometallurgically processed to produce Fe-Ni alloy and Ni matte. The key to achieving the highest recovery degrees from nickel ore in electric arc furnaces and producing top-quality ferro-nickel alloys lies in maintaining optimal carbon consumption and carefully controlling the composition of the slag. This research work focused on finding the optimal smelting procedure for extracting ferro-nickel from calcined nickel ore. Comparing experimental data to the results of thermodynamic modeling using Factsage 8.2 software was a key part of the study. The nickel smelting process, which involved a carbon consumption of 4 wt.%, resulted in ferro-nickel with an Fe/Ni ratio of 4.89 and slag with a nickel content of just 0.017%. The structure and properties of nickel slag in the MgO-SiO₂-FeO system were investigated by observing the changes in the MgO/SiO₂ ratio. This study found a significant nickel recovery degree of 95.6% within the optimal M/S ratio range of 0.65 to 0.7. When the M/S ratio exceeds 0.7, iron-rich magnesium silicates (Mg_xFe_ySiO_2+n) are generated within the slag. These compounds are released downwards due to their higher specific weight, restricting the movement of small metal particles and contributing to increased metal loss through the slag. Optimized slags could revolutionize smelting, increasing metal recovery while minimizing environmental impact. Full article

Ferronickel slag (FNS) is a byproduct produced during ferronickel alloy manufacturing, primarily used in the manufacturing of stainless steel and iron alloys. This material is produced by cooling molten slag with water or air, posing significant disposal challenges, as improper storage in industrial yards can lead to environmental contamination. This study investigates the chemical and mineralogical characteristics of reduction ferronickel slag (RFNS) and its potential use as an alternative aggregate in hot mix asphalt (HMA). The research is based on the practical application of HMA containing RFNS in an experimental area, specifically the parking lot used by buses transporting employees of Anglo American, located at the Codemin Industrial Unit in Niquelândia, Goiás, Central Brazil. Chemical analysis revealed that RFNS primarily consists of MgO, Fe₂O₃, and SiO₂, which are elements with minimal environmental impact. The lack of significant calcium content minimizes concerns about expansion issues commonly associated with calcium-rich slags. The X-ray diffractogram indicates a predominantly crystalline structure with minerals like Laihunite and Magnetite, which enhances wear and abrasion resistance. HMA containing 40% RFNS was tested using the Marshall methodology, and a small experimental area was subsequently constructed. The HMA containing RFNS met regulatory specifications and technological controls, achieving an average resilient modulus value of 6323 MPa. Visual inspections conducted four years later confirmed that the pavement remained in excellent condition, validating RFNS as a durable and effective alternative aggregate for asphalt mixtures. The successful application of RFNS not only demonstrates its potential for local road paving near industrial areas but also underscores the importance of sustainable waste management solutions. This research highlights the value of academia–industry collaboration in advancing environmentally responsible practices and reinforces the contribution of RFNS to enhancing local infrastructure and promoting a more sustainable future. Full article

Knowledge of the phase equilibria in the MgO–CaO–SiO₂–Al₂O₃ slag system is crucial for the nickel laterite smelting process. The phase equilibria of this slag system were experimentally investigated, focusing on the olivine and tridymite/cristobalite primary phase fields, using high-temperature equilibration and quenching methods, followed by Scanning Electron Microscopy–Energy Dispersive X-Ray analysis. The phase equilibria of the MgO–CaO–SiO₂ slag system at 1400 °C and 1500 °C were first determined in the absence of ferronickel alloy. The phase equilibria between 1400 °C, 1450 °C, and 1500 °C were then determined under a reducing condition, i.e., at equilibrium with ferronickel alloy and solid carbon. Finally, the effect of Al₂O₃ addition on the liquidus and solidus compositions in the slag system under the reducing condition was investigated at 1400 °C and 1450 °C. Comparisons between the experimentally constructed diagram, previous data, and FactSage-predicted phase diagrams have been provided and discussed. The present study identified the liquid slag both in the absence and presence of ferronickel alloy and solid carbon, as well as in the presence of Al₂O₃ impurity, within the formation boundaries of olivine and tridymite/cristobalite solids. Identifying the liquid slag area is essential to ensure that the nickel laterite smelting slag can be tapped from the furnace. Full article

Ferronickel slag is the solid waste slag produced by smelting nickel–iron alloy. After grinding ferronickel slag into powder, it has potential chemical activity. It can partially replace cement and reduce the amount of cement, and is conducive to environmental protection. The mechanical properties of soil cement were investigated through the compressive strength test and inter-split tensile test of ferronickel slag powder soil cement with different dosages. To further study the mechanism of ferronickel slag powder’s action on soil cement microscopically, the microstructure of soil cement was analyzed by using a scanning electron microscope and nuclear magnetic resonance equipment. The results of the study show that the incorporation of ferronickel slag powder can enhance the compressive and tensile strength of soil cement. The best performance enhancement of ferronickel slag powder was achieved when it was doped with 45% of its mass. The hydration products of soil cement increased with the increase in the doping amount, but the excessive doping of ferronickel slag powder would lead to a weakening of the hydration reaction and a decrease in the strength of the soil cement. At the same time, ferronickel slag powder plays the role of filling the void of soil cement. With the increase in ferronickel slag powder, the large pores inside the soil cement are reduced and the structure is denser. Full article

Soft soil foundations in marine environments are under coupling actions of seawater erosion and dry–wet cycles due to tides. Ferronickel slag is a solid waste produced in the smelting of ferronickel alloys. To recycle industrial solid waste and conserve energy, ferronickel slag is partially substituted for cement to solidify the soft soil foundations in marine environments. Unconfined compression tests were conducted for soil–cement mixed with ferronickel slag of various proportions to investigate its apparent erosion characteristics and mechanical characteristics under dry–wet cycles. In the tests, the corresponding numbers of cycles were set to 0, 6, 12, and 18. To further investigate the microscopic action mechanism of ferronickel slag on soil–cement, a nuclear magnetic resonance (NMR) device was utilized to analyze the microstructure of the soil–cement. According to the testing results, the unconfined compressive strength of soil–cement first increased and then decreased when the number of cycles of seawater erosion increased. With other conditions being the same, the addition of ferronickel slag can improve soil–cement strength, and changes in soil–cement strength were more significant than that with no ferronickel slag mixed. Moreover, the optimal amount of admixture was proved to be 45%. As the number of dry–wet cycles increased, the mass of soil–cement first increased and then decreased. With the same number of dry–wet cycles, soil–cement mixed with ferronickel slag had a smaller mass loss rate than that with no ferronickel slag added. After six dry–wet cycles, apparent erosion of soil–cement becomes increasingly serious, including the absence of edges and corners, deformation of surfaces, and even spalling and cracking. The NMR analysis revealed that dry–wet cycles can promote the evolution of small pores into larger ones within the soil–cement, thereby increasing the number of larger pores, leading to an increase in porosity, a decrease in the compactness of the soil–cement, and a reduction in strength. Full article

Electric furnace ferronickel slag (EFS) is a typical magnesium-rich industrial by-product discharged from the manufacture of nickel and iron-nickel alloys. The approach to use it as the raw material for the preparation of magnesium phosphate cement (MPC) has potential and proves effective. In this study, three different phosphorus sources (PS) including phosphoric acid (H₃PO₄, PA), sodium dihydrogen phosphate (NaH₂PO₄, SDP) and potassium dihydrogen phosphate (KH₂PO₄, PDP) were used to react with EFS to prepare the EFS-based MPC (EMPC), and the effects of raw material mass ratio (EFS/PA, EFS/SDP, EFS/PDP) on the compressive strength, early hydration temperature and microstructure of EMPC pastes were investigated. Results showed that the compressive strength of EMPC paste is significantly impacted by the type of phosphorus source and the raw materials mass ratio. When the EFS/PDP ratio is 4.0, the compressive strength of the MPC paste reaches up to 18.8, 22.8 and 27.5 MPa at 3, 7 and 28 d, respectively. Cattiite (Mg₃(PO₄)₂·22H₂O), K-struvite (KMgPO₄·6H₂O) and/or Na-struvite (NaMgPO₄·6H₂O) were identified as the main hydration products of EMPC. The development of EMPC mainly involves the dissolution of a phosphorus source, MgO and Mg₂SiO₄, formation of hydration product as binder, and combination of the unreacted raw materials together by binders to build a compact form. Full article

The production of ferroalloys and alloys like ferronickel, ferrochromium, ferromanganese, silicomanganese, ferrosilicon and silicon is commonly carried out in submerged arc furnaces. Submerged arc furnaces are also used to upgrade ilmenite by producing pig iron and a titania-rich slag. Metal containing resources are smelted in this furnace type using fossil carbon as a reducing agent, which is responsible for a large amount of direct CO₂ emissions in those processes. Instead, renewable bio-based carbon could be a viable direct replacement of fossil carbon currently investigated by research institutions and companies to lower the CO₂ footprint of produced alloys. A second option could be the usage of hydrogen. However, hydrogen has the disadvantages that current production facilities relying on solid reducing agents need to be adjusted. Furthermore, hydrogen reduction of ignoble metals like chromium, manganese and silicon is only possible at very low H₂O/H₂ partial pressure ratios. The present article is a comprehensive review of the research carried out regarding the utilization of bio-based carbon for the processing of the mentioned products. Starting with the potential impact of the ferroalloy industry on greenhouse gas emissions, followed by a general description of bio-based reducing agents and unit operations covered by this review, each following chapter presents current research carried out to produce each metal. Most studies focused on pre-reduction or solid-state reduction except the silicon industry, which instead had a strong focus on smelting up to an industrial-scale and the design of bio-based carbon for submerged arc furnace processes. Those results might be transferable to other submerged arc furnace processes as well and could help to accelerate research to produce other metals. Deviations between the amount of research and scale of tests for the same unit operation but different metal resources were identified and closer cooperation could be helpful to transfer knowledge from one area to another. Life cycle assessment to produce ferronickel and silicon already revealed the potential of bio-based reducing agents in terms of greenhouse gas emissions, but was not carried out for other metals until now. Full article

Blast furnace ferronickel slag (BFFS) is generated in the production of ferronickel alloys and is used as cement replacement in concrete or mortar. The effectivity in reducing cement consumption and improving performance are limited. By referring to the paste replacement method, this work used BFFS to replace an equal volume of the white Portland cement paste to obtain greater performance enhancement. BFFS was used with five levels of replacement (0%, 5%, 10%, 15%, 20%) and four water-to-cement ratios (0.40, 0.45, 0.50, 0.55) were designed. Fluidity, mechanical strength, hydration products, and pore structure of every mixture were measured. The results showed that the workability of the mortars decreased due to the reduced volume of water, but the 28-day compressive strength of the mortars increased, and the cement content of the mortars was also reduced by 33 wt %. The X-ray diffraction (XRD) patterns revealed that there existed a carboaluminate phase, and the presence of the ettringite was stabilized, indicating that the accumulating amount of the hydration products of the mortar increased. Furthermore, the BFFS could consume the portlandite and free water to form a higher amount of chemically bound water due to its pozzolanic activity. A high degree of hydration and a large volume of the hydration products refined the porosity of the hardened mortars, which explained the enhancement of the strength of the mortars. Compared to the cement replacement method, the paste replacement method was more effective in preparing eco-friendly mortar or concrete by recycling BFFS for reducing the cement content of the mortar while improving its strength. Full article

The primary energy consumption and greenhouse gas emissions from nickel smelting products have been assessed through case studies using a process model based on mass and energy balance. The required primary energy for producing nickel metal, nickel oxide, ferronickel, and nickel pig iron is 174 GJ/t alloy (174 GJ/t contained Ni), 369 GJ/t alloy (485 GJ/t contained Ni), 110 GJ/t alloy (309 GJ/t contained Ni), and 60 GJ/t alloy (598 GJ/t contained Ni), respectively. Furthermore, the associated GHG emissions are 14 tCO₂-eq/t alloy (14 tCO₂-eq/t contained Ni), 30 t CO₂-eq/t alloy (40 t CO₂-eq/t contained Ni), 6 t CO₂-eq/t alloy (18 t CO₂-eq/t contained Ni), and 7 t CO₂-eq/t alloy (69 t CO₂-eq/t contained Ni). A possible carbon emission reduction can be observed by comparing ore type, ore grade, and electricity source, as well as allocation strategy. The suggested process model overcomes the limitation of a conventional life cycle assessment study which considers the process as a ‘black box’ and allows for an identification of further possibilities to implement sustainable nickel production. Full article

Nickel, a valued metal, mainly exists as nickel oxide in laterite nickel ore. Furthermore, a large part of the laterite nickel ore is low-grade saprolitic ore. In this paper, a research on preparing ferro-nickel alloy from low-grade saprolitic laterite nickel ore using metallized reduction-magnetic separation was studied. In the research, the carbothermic reductions of iron oxide and nickel oxide were analyzed in terms of thermodynamics. The influences of reduction temperature, reduction time, carbon ratio, and CaO addition on the recoveries and grades of iron and nickel were experimentally investigated. To analyze and clarify the related mechanism, the microstructure of ferro-nickel alloy was observed by optical microscope (OM) and scanning electron microscope/energy dispersive spectrometer (SEM/EDS). Accordingly, the results showed that, increasing reduction temperature can improve the grades and recoveries of nickel and iron; appropriate reduction time, carbon ratio and CaO addition can favor aggregation and growing up of the ferro-nickel particles, improving the grades and recoveries of nickel and iron. The optimal process parameters obtained were a reduction temperature of 1350 °C, reduction time of 2 h, carbon ratio of 1.2, and CaO addition of 10%. In this case, the ferro-nickel alloy with nickel grade 7.90% and iron grade 77.32% was prepared successfully from the low-grade saprolitic ore with nickel content 1.82%. The nickel and iron recoveries were 89.36% and 95.87% respectively, which achieved the highly efficient recovery and utilization of iron and nickel of low-grade laterite nickel ore. Full article