Search Results (137)

Exposure of LIB materials to ambient conditions with some level of humidity, either accidentally owing to imperfect fabrication or cell damage, or deliberately due to battery opening operations for analytical or recycling purposes, is a rather common event. As far as humidity-induced damage is concerned, on the one hand the general chemistry is well known, but on the other hand, concrete structural details of these processes have received limited explicit attention. The present study contributes to this field with an investigation centered on the use of Raman spectroscopy for the assessment of structural modifications using common lithium iron phosphate (LFP) and nickel–cobalt–manganese/lithium–manganese oxide (NCM-LMO) cathodes. The impact of humidity has been followed through the observation of differences in Raman bands of pristine and humidity-exposed cathode materials. Vibrational spectroscopy has been complemented with morphological (SEM), chemical (EDS), and electrochemical analyses. We have thus pinpointed the characteristic morphological and compositional changes corresponding to corrosion and active material dissolution. Electrochemical tests with cathodes reassembled in coin cells allowed for the association of specific capacity losses with humidity damaging. Full article

Rapid growth of electric vehicles has increased demand for lithium-ion batteries (LIBs), raising concerns regarding their end-of-life management. This study comprehensively evaluates the closed-loop recycling of cathode materials from spent LIBs by integrating life cycle assessment (LCA), technoeconomic analysis, and technological comparison. Typical approaches—including pyrometallurgy, hydrometallurgy, and other processes such as organic acid leaching and in situ reduction roasting—are systematically reviewed. While pyrometallurgy offers scalability, it is hindered by high energy consumption and excessive greenhouse gas emissions. Hydrometallurgy achieves higher metal recovery rates with better environmental performance but requires complex chemical and wastewater management. Emerging methods and regeneration techniques such as co-precipitation and sol–gel synthesis demonstrate potential for high-purity material recovery and circular manufacturing. LCA results confirm that recycling significantly reduces GHG emissions, especially for high-nickel cathode chemistry. However, the environmental benefits are affected by upstream factors such as collection, disassembly, and logistics. Technoeconomic simulations show that profitability is strongly influenced by battery composition, regional cost structures, and collection rates. The study highlights the necessity of harmonized LCA boundaries, process optimization, and supportive policy frameworks to scale environmentally and economically sustainable LIB recycling, ensuring long-term supply security for critical battery materials. Full article

Graphite has been recognized as a critical material by the United States (US), the European Union (EU), and Australia. Owing to its unique structure and properties, it is utilized in many industries and has played a key role in the clean energy sector, particularly in the lithium-ion battery (LIB) industries. With the projected increase in global graphite demand, driven by the shift to clean energy and the use of EVs, as well as the geographically concentrated production and reserves of natural graphite, interest in graphite recycling has increased, with a specific focus on using spent LIBs and other waste carbon material. Although most established and developing LIB recycling technologies are focused on cathode materials, some have started recycling graphite, with promising results. Based on the different secondary sources and recycling paths reported, hydrometallurgy-based treatment is usually employed, especially for the purification of graphite; greener alternatives are being explored, replacing HF both in lab-scale research and in industry. This offers a viable solution to resource dependency and mitigates the environmental impact associated with graphite production. These developments signal a trend toward sustainable and circular pathways for graphite recycling. Full article

Global resource consumption continues to grow each year, exerting increasing pressure on their availability. This trend could lead to a shortage of raw materials in the coming years. Aware of the risks associated with this situation, the European Union has implemented policies and strategies aimed at diversifying its supply sources, including waste recycling. In this context, the present study was conducted with the objective of developing innovative processes to concentrate valuable metals present in the non-recovered fractions of waste electrical and electronic equipment (WEEE). Three types of samples were studied: washing table residues (WTRs), printed circuit boards (PCBs), and powders from cathode-ray tube screens (CRT powders). Several separation techniques, based on the physical properties of the elements, were implemented, including electrostatic separation, magnetic separation, and density and gravity-based separations. The results obtained are promising. For WTRs and PCBs, the recovery rates of targeted metals (Cu, Al, Pb, Zn, Sn) reached approximately 91% and 80%, respectively. In addition to these metals, other valuable metals, present in significant quantities, deserve further exploration. Regarding CRT powders, the performances are also encouraging, with recovery rates of 54.7% for zinc, 57.1% for yttrium, and approximately 71% for europium. Although these results are satisfactory, optimizations are possible to maximize the recovery of these critical elements. The techniques implemented have demonstrated their effectiveness in concentrating target metals in the treated fractions. These results confirm that recycling constitutes a viable alternative to address resource shortages and secure part of the supplies needed for the European Union’s industry. Full article

The conventional spent lithium-ion batteries (LIBs) recycling method suffers from complex processes and excessive chemical consumption. Hence, this study proposes an electrochemical strategy for achieving reductant-free leaching of high-valence transition metals and efficient separation of valuable components from spent cathode sheets (CSs). An innovatively designed sandwich-structured electrochemical reactor achieved efficient reductive dissolution of cathode materials (CMs) while maintaining the structural integrity of aluminum (Al) foils in a dilute sulfuric acid system. Optimized current enabled leaching efficiencies exceeding 93% for lithium (Li), cobalt (Co), manganese (Mn), and nickel (Ni), with 88% metallic Al foil recovery via cathodic protection. Multi-scale characterization systematically elucidated metal valence evolution and interfacial reaction mechanisms, validating the technology’s tripartite innovation: simultaneous high metal extraction efficiency, high value-added Al foil recovery, and organic removal through single-step electrochemical treatment. The process synergized the dissolution of CM particles and hydrogen bubble-induced physical liberation to achieve clean separation of polyvinylidene difluoride (PVDF) and carbon black (CB) layers from Al foil substrates. This method eliminates crushing pretreatment, high-temperature reduction, and any other reductant consumption, establishing an environmentally friendly and efficient method of comprehensive recycling of battery materials. Full article

Purely electric and hybrid vehicles are emerging as the transport sector’s response to meet climate goals, aiming to mitigate global warming. As the adoption of transport electrification increases, the importance of recycling components of the electric propulsion system at the end of their life grows, particularly the battery pack, which significantly contributes to the vehicle’s final cost and generates environmental impacts and CO₂ during production. This work presents an overview of the recycling processes for lithium-ion automotive batteries, emphasizing the developing Brazilian scenario and more established international scenarios. In Brazil, companies and research centers are investing in recycling and using reused cathode material to manufacture new batteries through the hydrometallurgical process. On the international front, pyrometallurgy and physical recycling are being applied, and other methods, such as direct processes and biohydrometallurgy, are also under study. Regardless of the recycling method, the main challenge is scaling prototype processes to meet current and future battery demand, driven by the growth of electric and hybrid vehicles, pursuing both environmental gains through reduced mining and CO₂ emissions and economic viability to make recycling profitable and support global electrification. Full article

In the wake of global energy transition and the “dual-carbon” goal, the rapid growth of electric vehicles has posed challenges for large-scale lithium-ion battery decommissioning. Retired batteries exhibit dual attributes of strategic resources (cobalt/lithium concentrations several times higher than natural ores) and environmental risks (heavy metal pollution, electrolyte toxicity). This paper systematically reviews pyrometallurgical and hydrometallurgical recovery technologies, identifying bottlenecks: high energy/lithium loss in pyrometallurgy, and corrosion/cost/solvent regeneration issues in hydrometallurgy. To address these, an integrated recycling process is proposed: low-temperature physical separation (liquid nitrogen embrittlement grinding + froth flotation) for cathode–anode separation, mild roasting to convert lithium into water-soluble compounds for efficient metal oxide separation, stepwise alkaline precipitation for high-purity lithium salts, and co-precipitation synthesis of spherical hydroxide precursors followed by segmented sintering to regenerate LiNi_1/3Co_1/3Mn_1/3O₂ cathodes with morphology/electrochemical performance comparable to virgin materials. This low-temperature, precision-controlled methodology effectively addresses the energy-intensive, pollutive, and inefficient limitations inherent in conventional recycling processes. By offering an engineered solution for sustainable large-scale recycling and high-value regeneration of spent ternary lithium ion batteries (LIBs), this approach proves pivotal in advancing circular economy development within the renewable energy sector. Full article

The recycling of proton exchange membrane water electrolyzer (PEMWE) raw materials is imperative due to their scarcity, cost, complexity and environmental impact. This is particularly true in the context of expanding electrolyzer manufacturing and reducing production costs. Developing comprehensive recycling strategies requires the creation of a model stack due to the diversity in stack design, structure and materials. The review-derived model presented here provides a sound basis and summarizes the variety of approaches found in the literature and industry. The holistically developed recycling chain, including dismantling, mechanical processing, hydrometallurgical processes and carbon reuse, is characterized by the complete recycling of materials, the reduced application of energy-intensive process steps and the avoidance of environmentally harmful processes. Emphasis is placed on demonstrating the non-destructive disassembly of joined components, the dry mechanical decoating of catalyst-coated membranes, membrane dissolution, the separation of anode and cathode particles and the environmentally friendly hydrometallurgical processing of platinum. Full article

The rapid growth of lithium iron phosphate (LiFePO₄, LFP)-based lithium-ion batteries in energy storage raises urgent challenges for resource recovery and environmental protection. In this study, we propose a novel method for rapid and selective lithium extraction and the resynthesis of cathodes from spent LFP batteries, aiming to achieve an economically feasible and efficient recycling process. In this process, a selective leaching H₂SO₄-H₂O₂ system is employed to rapidly and selectively extract lithium, achieving a leaching efficiency of 98.72% within just 10 min. Through an exploration of the precipitation conditions of the lithium-containing solution, high-purity Li₂CO₃ is successfully obtained. The recovered FePO₄ and Li₂CO₃ are then used to resynthesize LFP cathode materials through a carbon-thermal reduction method. A preliminary economic analysis reveals that the disposal cost of spent LFP batteries is approximately USD 2.63 per kilogram, while the value of regenerated LFP reaches USD 4.46, highlighting the economic advantages of this process. Furthermore, with an acid-to-lithium molar ratio of only 0.57—just slightly above the stoichiometric 0.5—the process requires minimal acid usage, offering clear environmental benefits. Overall, this work presents a green, efficient, and economically viable strategy for recycling spent LFP batteries, showcasing strong potential for industrial application and contributing significantly to the development of a circular lithium battery economy. Full article

The increasing demand for lithium-ion batteries (LIBs) and their limited lifespan emphasize the urgent need for sustainable recycling strategies. This study investigates the application of tetrabutylphosphonium-based ionic liquids (ILs) as alternative leaching agents for recovering critical metals, Li(I), Co(II), Ni(II), and Mn(II), from spent NMC cathode materials. Initial screening experiments evaluated the leaching efficiencies of nine tetrabutylphosphonium-based ILs for Co(II), Ni(II), Mn(II), and Li(I), revealing distinct metal dissolution behaviors. Three ILs containing HSO₄⁻, EDTA²⁻, and DTPA³⁻ anions exhibited the highest leaching performance and were selected for further optimization. Key leaching parameters, including IL and acid concentrations, temperature, time, and solid-to-liquid ratio, were systematically adjusted, achieving leaching efficiencies exceeding 90%. Among the tested systems, [TBP][HSO₄] enabled near-complete metal dissolution (~100%) even at room temperature. Furthermore, an aqueous biphasic system (ABS) was investigated utilizing [TBP][HSO₄] in combination with ammonium sulfate, enabling the complete extraction of all metals into the salt-rich phase while leaving the IL phase metal-free and potentially suitable for reuse, indicating the feasibility of integrating leaching and extraction into a continuous, interconnected process. This approach represents a promising step forward in LIB recycling, highlighting the potential for sustainable and efficient integration of leaching and extraction within established hydrometallurgical frameworks. Full article

With the growing demand for metals driven by technological advancements and population growth, recycling lithium-ion batteries has become vital for protecting the environment and recovering valuable materials. Developing sustainable recycling technologies is now more essential than ever. This paper focuses on using electrodialysis to process a leach solution of LiNi_0.33Mn_0.33Co_0.33O₂ (NMC 111) cathode materials leached with citric acid. This study demonstrates that the complexing properties of citrate anions contribute to the efficient separation of Li from Ni, Co, and Mn by electrodialysis. This is achieved by promoting the formation of anionic species for Ni, Co, and Mn while maintaining Li in its cationic form. The leach solution was produced under the following optimal experimental conditions to reach a final pH of 5 and high leaching efficiency: a citric acid concentration of 1 mol L⁻¹, a leaching temperature of 45 °C, a leaching time of 5 h, a liquid/solid ratio of 100 g/L, and 8 vol.% H₂O₂. These conditions resulted in leaching efficiencies of 89.3% for Ni, 95.1% for Co, 77.1% for Mn, and 92.9% for Li. This solution led to the formation of a lithium-rich supernatant and a precipitate. The supernatant was then used as the feed solution for electrodialysis. Pure lithium was successfully separated with a faradic efficiency of 71.4% with a commercial cation-exchange membrane. This strategy enables selective lithium recovery while minimizing membrane fouling during the process. Full article

Lithium-ion batteries (LIBs) are widely used in diverse applications, ranging from portable ones to stationary ones. The appropriate handling of the immense amount of spent batteries has, therefore, become significant. Whether recycled or repurposed for second-life applications, knowing their chemistry type can lead to higher efficiency. In this paper, we propose a novel machine learning-based approach for accurate chemistry identification of the electrode materials in LIBs based on their temperature dynamics under constant current cycling using gated recurrent unit (GRU) networks. Three different chemistry types, namely lithium nickel cobalt aluminium oxide cathode with silicon-doped graphite anode (NCA-GS), nickel cobalt aluminium oxide cathode with graphite anode (NCA-G), and lithium nickel manganese cobalt oxide cathode with graphite anode (NMC-G), were examined under four conditions, 0.2 C charge, 0.2 C discharge, 1 C charge, and 1 C discharge. Experimental results showed that the unique characteristics in the surface temperature measurement during the full charge or discharge of the different chemistry types can accurately carry out the classification task in both experimental setups, where the model is trained on data under different cycling conditions separately and jointly. Furthermore, experimental results show that the proposed approach for chemistry type identification based on temperature dynamics appears to be more universal than voltage characteristics. As the proposed approach has proven to be efficient in the chemistry identification of the electrode materials LIBs in most cases, we believe it can greatly benefit the recycling and second-life application of spent LIBs in real-life applications. Full article

Today, lithium-ion batteries (LIBs) are widespread and play a vital role in advancing portable electronics (laptops and mobile phones), green energy technology (electrical vehicles), and renewable energy systems. There is about 30% off-spec scrap LIB production during manufacturing. This trend has caused the accumulation of a huge number of spent LIBs. In addition to containing chemicals that are harmful to the environment, these batteries also contain critical metals; their recycling will greatly help to maintain a green and sustainable economic transition. Therefore, this issue has forced researchers to seek cost-effective and eco-friendly strategies for recycling LIBs. The pretreatment of waste batteries is an essential part of LIB recycling. This article aims to comprehensively review the basic structure of LIBS and existing pretreatment methods in recycling critical metals from LIBs, with a special focus on recent innovations. This manuscript has been prepared to help researchers conduct cutting-edge and novel research in LIB pretreatment and recycling. This approach not only helps researchers to understand the concepts, but also helps to identify and evaluate the strengths and weaknesses of different pretreatment methods. Also, in addition to mentioning the existing research limitations, suggestions for future research perspectives and less investigated areas that need further research have been presented. Full article

With the large-scale application of lithium-ion batteries in the field of new energy, many retired lithium batteries not only cause environmental pollution problems but also lead to serious waste of resources. Repairing failed lithium batteries and regenerating new materials has become a crucial path to break through this dilemma. Based on the research on the failure mechanism of ternary cathode materials, this paper systematically combs through the multiple factors leading to their failure, extensively summarizes the influence of heat treatment process parameters on the performance of recycled materials, and explores the synergistic effect between heat treatment technology and other processes. Studies have shown that the failure of ternary cathode materials is mainly attributed to factors such as cation mixing disorder, the generation of microcracks, phase structure transformation, and the accumulation of by-products. Among them, cation mixing disorder damages the crystal structure of the material, microcracks accelerate the pulverization of the active substance, phase structure transformation leads to lattice distortion, and the generation of by-products will hinder ion transport. The revelation of these failure mechanisms lays a theoretical foundation for the efficient recycling of waste materials. In terms of recycling technology, this paper focuses on the application of heat treatment technology. On the one hand, through synergy with element doping and surface coating technologies, heat treatment can effectively improve the crystal structure and surface properties of the material. On the other hand, when combined with processes such as the molten salt method, coprecipitation method, and hydrothermal method, heat treatment can further optimize the microstructure and electrochemical properties of the material. Specifically, heat treatment plays multiple key roles in the recycling process of ternary cathode materials: repairing crystal structure defects, enhancing the electrochemical performance of the material, removing impurities, and promoting the uniform distribution of elements. It is a core link to achieving the efficient reuse of waste ternary cathode materials. Full article

The performance and scalability of energy storage systems play a key role in the transition toward intermittent renewable energy systems and the achievement of decarbonization targets through means of resilient electrical grids. Despite significant research and technology advancements, the scalability of innovative energy storage systems remains challenging due to the scarcity of raw materials (used for the production of energy storage media, cathodes, anodes, separators, conductive agents, and electrolytes). The European Commission has identified certain raw materials as both economically important and subject to supply risks, designating them as critical and strategic raw materials. In this review, a comprehensive analysis is conducted regarding 28 raw materials and rare earth elements which are essential for the production of batteries, supercapacitors, and other storage systems, emphasizing their criticality, strategic importance, supply chain vulnerabilities, and associated environmental and social impacts. This study also addresses potential substitute materials for energy storage devices and innovations that make these devices recyclable. Future trends are briefly discussed, including advancements in alternative chemistries and innovations to improve energy density in advanced batteries and supercapacitors, paving the way for hybrid energy solutions. Full article