Search Results (52)

We report a comprehensive spectroscopic, microscopic, and device-level investigation of the ambient-driven degradation of PTQ10:IDIC bulk-heterojunction organic solar cells (BHJ-OSCs), up to 500 h. The power conversion efficiency dropped from 9.51% to 7.69% (≈19% relative loss), primarily due to a decrease in short-circuit current density (J_SC 15.93 to 13.82 mA cm⁻²), while the open-circuit voltage remained largely stable (0.92 to 0.90 V). Atomic force microscopy reveals surface smoothing upon ageing, with the root-mean-square roughness decreasing from 4.29 to 3.45 nm, and the UV–vis absorption spectra show negligible changes, indicating preserved bulk light-harvesting capability. In contrast, X-ray photoelectron spectroscopy indicates pronounced surface compositional evolution, with a decrease in oxygen (5.18 to 3.18%) and a substantial increase in fluorine content (3.23 to 7.23%), consistent with fluorine-rich surface segregation or reorientation. Ultraviolet photoelectron spectroscopy further reveals a 0.48 eV reduction in surface work function, indicative of surface dipole modification and near-surface electronic reorganization. Collectively, these results demonstrate that ambient ageing primarily impacts interfacial chemistry and morphology rather than bulk optoelectronic properties, highlighting interfacial engineering and encapsulation as effective strategies for improving long-term device stability. Full article

Thin-film organic solar cells (TFOSCs) are gaining momentum as next-generation photovoltaic technologies due to their lightweight nature, mechanical flexibility, and low cost-effective fabrication. In this pioneering study, we report for the first time the incorporation of cobalt-doped zinc sulfide $(\mathrm{Z}\mathrm{n}\mathrm{S}/\mathrm{C}\mathrm{o})$ nanoparticles (NPs) into a poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PC61BM) bulk-heterojunction photoactive layer. $\mathrm{Z}\mathrm{n}\mathrm{S}/\mathrm{C}\mathrm{o}$ NPs were successfully synthesized via a wet chemical method and integrated at varying concentrations (1%wt, 3%wt, and 5%wt) to systematically investigate their influence on device performance. The optimal doping concentration of 3%wt yielded a remarkable power conversion efficiency (PCE) of 4.76%, representing a 102% enhancement over the pristine reference device (2.35%) under ambient laboratory conditions. The observed positive trend is attributed to the localized surface plasmon resonance (LSPR) effect and near-field optical enhancement induced by the presence of ZnS/Co NPs in the active layer, thereby increasing light-harvesting capability and exciton dissociation. Comprehensive morphological and optical characterizations using high-resolution scanning electron microscopy (HRSEM), high-resolution transmission electron microscopy (HRTEM), and spectroscopic techniques confirmed uniform nanoparticle dispersion, nanoscale crystallinity, and effective light absorption. These findings highlight the functional role of $\mathrm{Z}\mathrm{n}\mathrm{S}/\mathrm{C}\mathrm{o}$ NPs as dopants in enhancing TFOSC performance, providing valuable insights into optimizing nanoparticle concentration. This work offers a scalable and impactful strategy for advancing high-efficiency, flexible, and wearable organic photovoltaic devices. Full article

This work introduces a general solution for printing wavelength-selective bulk-heterojunction photosensitive organic field effect transistors (PS-OFETs) by addressing electrode thickness variation and the feasibility of color selectivity in detecting incident light. The inkjet-printed silver electrode thickness was varied from 125 to $950 \mathrm{n}\mathrm{m}$ by multilayer printing. PIF, IDFBR, and ITIC-4F were chosen as the active semiconductor materials with complementary optical absorption. Results indicate that PS-OFETs exhibit the best functionality at an electrode thickness of approximately $325 \mathrm{n}\mathrm{m}$ and an active material combination with PIF:IDFBR (1:1). For the $540 \mathrm{n}\mathrm{m}$ wavelength, a responsivity of $55 \mathrm{m}\mathrm{A}{\mathrm{W}}^{-1}$ was obtained. This is four-fold higher than the photoresponse obtained at $700 \mathrm{n}\mathrm{m}$. Full article

In this study, we detailed the fabrication and characterization of photovoltaic structures based on PTB7:ICBA (1:1, wt.%) bulk-heterojunction on optical glass substrates by spin-coating. Some samples were deposited on a flat substrate, and others were placed on a patterned substrate obtained by nano-imprinting lithography; the induced effects were analyzed. We demonstrated that using a patterned substrate enhanced the maximum output power, primarily because the short-circuit current density increased. This can be considered a direct consequence of reduced optical reflection and improved optical absorption. The topological parameters evaluated by atomic force microscopy, namely, the root mean square, Skewness, and Kurtosis, had small values of around 2 nm and 1 nm, respectively. This proves that the mixture of a conductive polymer and a fullerene derivative creates a thin film network with a high flatness degree. The samples discussed in this paper were fabricated and characterized in air; we can admit that the results are encouraging, but further optimization is needed. Full article

The ternary blending strategy is a fundamental approach that is widely recognized in the field of organic optoelectronics. In our investigation, leveraging the inherent advantages of the ternary component blending methodology, we introduced an innovative design for organic photodetectors (OPDs) aimed at reducing the dark current density (J_d) under reverse bias. This pioneering effort involved combining two distinct conjugated molecules (IT-4F and IEICO-4F) with a conjugated polymer (PM7), resulting in a composite material characterized by a well-defined vertical phase separation. To thoroughly explore device performance variations, we utilized a comprehensive array of analytical techniques, including atomic force microscopy (AFM) cross-section methodologies and Kelvin probe force microscopy (KPFM). Through the optimization of the blend ratio (PM7:IT-4F: IEICO-4F at 1:0.8:0.2), we achieved significant advancements. The resulting OPD demonstrated an exceptional reduction in JD, reaching a remarkably low value of 4.95 × 10⁻¹⁰ A cm⁻², coupled with an ultra-high detectivity of 4.95 × 10¹³ Jones and an outstanding linear dynamic range exceeding 100 dB at 780 nm under a bias of −1V. Furthermore, the attained cutoff frequency reached an impressive 220 kHz, highlighting substantial improvements in device performance metrics. Of particular significance is the successful translation of this technological breakthrough into real-world applications, such as in heart rate sensing, underscoring its tangible utility and expanding its potential across various fields. This demonstrates its practical relevance and underscores its versatility in diverse settings. Full article

The bulk-heterojunction (BHJ) system that uses a $\pi$-conjugated polymer as an electron donor, and a fullerene derivative as an electron acceptor, is widely used in organic solar cells (OSCs) to facilitate efficient charge separation and extraction. However, the conventional BHJ system still suffers from unwanted phase segregation caused by the existence of significant differences in surface energy between the two BHJ components and the charge extraction layer during film formation. In the present work, we demonstrate a sophisticated control of fast film-growth kinetics that can be used to achieve a uniform distribution of donor and acceptor materials in the BHJ layer of OSCs without undesirable phase separation. Our approach involves depositing the BHJ solution onto a spinning substrate, thus inducing rapid evaporation of the solvent during BHJ film formation. The fast-growth process prevents the fullerene derivative from migrating toward the charge extraction layer, thereby enabling a homogeneous distribution of the fullerene derivative within the BHJ film. The OSCs based on the fast-growth BHJ thin film are found to exhibit substantial increases in J_SC, fill factor, and a PCE up to 11.27 mA/cm², 66%, and 4.68%, respectively; this last value represents a remarkable 17% increase in PCE compared to that of conventional OSCs. Full article

In conventional fullerene-based organic photovoltaics (OPVs), in which the excited electrons from the donor are transferred to the acceptor, the electron charge transfer state (^eE_CT) that electrons pass through has a great influence on the device’s performance. In a bulk-heterojunction (BHJ) system based on a low bandgap non-fullerene acceptor (NFA), however, a hole charge transfer state (^hE_CT) from the acceptor to the donor has a greater influence on the device’s performance. The accurate determination of ^hE_CT is essential for achieving further enhancement in the performance of non-fullerene organic solar cells. However, the discovery of a method to determine the exact ^hE_CT remains an open challenge. Here, we suggest a simple method to determine the exact ^hE_CT level via deconvolution of the EL spectrum of the BHJ blend (EL_B). To generalize, we have applied our EL_B deconvolution method to nine different BHJ systems consisting of the combination of three donor polymers (PM6, PBDTTPD-HT, PTB7-Th) and three NFAs (Y6, IDIC, IEICO-4F). Under the conditions that (i) absorption of the donor and acceptor are separated sufficiently, and (ii) the onset part of the external quantum efficiency (EQE) is formed solely by the contribution of the acceptor only, EL_B can be deconvoluted into the contribution of the singlet recombination of the acceptor and the radiative recombination via ^hE_CT. Through the deconvolution of EL_B, we have clearly decided which part of the broad EL_B spectrum should be used to apply the Marcus theory. Accurate determination of ^hE_CT is expected to be of great help in fine-tuning the energy level of donor polymers and NFAs by understanding the charge transfer mechanism clearly. Full article

In this study, we present a comprehensive investigation into the charge generation mechanism in bulk-heterojunction organic solar cells employing non-fullerene acceptors (NFAs) both with and without the presence of processing additives. While photovoltaic devices based on Y6 or BTP-eC9 have shown remarkable power conversion efficiencies, the underlying charge generation mechanism in polymer:NFA blends remains poorly understood. To shed light on this, we employ transient absorption (TA) spectroscopy to elucidate the charge transfer pathway within a blend of the donor polymer PM6 and NFAs. Interestingly, the charge carrier lifetimes of neat Y6 and BTP-eC9 are comparable, both reaching up to 20 ns. However, the PM6:BTP-eC9 blend exhibits substantially higher charge carrier generation and a longer carrier lifetime compared to PM6:Y6 blend films, leading to superior performance. By comparing TA data obtained from PM6:Y6 or PM6:BTP-eC9 blend films with and without processing additives, we observe significantly enhanced charge carrier generation and prolonged charge carrier lifetimes in the presence of these additives. These findings underscore the potential of manipulating excited species as a promising avenue for further enhancing the performance of organic solar cells. Moreover, this understanding contributes to the advancement of NFA-based systems and the optimization of charge transfer processes in polymer:NFA blends. Full article

The power conversion efficiencies (PCEs) of organic photovoltaics (OPVs) have reached more than 19%, along with the prosperous development of materials and device engineering. It is meaningful to make a comprehensive review of the research of OPVs for further performance improvement. In this review, some typical materials of high-performance OPVs are summarized, including representative polymer donor materials, non-fullerene acceptor materials, and interfacial modification materials, as well as their design rules for molecular engineering. From the point of view of device engineering, active layer treatment and deposition technology are introduced, which can play a critical role in adjusting the degree of molecular aggregation and vertical distribution. Meanwhile, a ternary strategy has been confirmed as an efficient method for improving the performance of OPVs, and the multiple roles of the appropriate third component in the photo-electronic conversion process are emphasized and analyzed. The challenges and perspectives concerning this region are also put forward for further developing high-performance OPVs. Full article

Single-junction organic solar cells have reached a power conversion efficiency of 20% with narrow bandgap non-fullerene electron acceptor materials such as Y6, as well as with large band gap electron donor materials and their derivatives. The power conversion efficiency improvement of single-junction organic solar cells is a result of highly efficient light harvesting in the near-infrared light range and reduced energy losses with the most promising active layer layout currently available, Bulk-Heterojunction. Ternary blending is known to be the most advanced strategy to construct Bulk-Heterojunction structures in organic solar cells at present. In this review, we examine different devices based on Bulk-Heterojunction structures with efficient electron donors and acceptors. Then, we review the performance of binary and ternary organic solar cells with high power conversion efficiency, in conjunction with different anode and cathode interfaces used in recent studies of high-power conversion efficiency. Finally, we present perspectives on the future development of single-junction organic solar cells. Full article

This work covers the development of non-fullerene acceptors for use in organic photovoltaics built using the N-annulated perylene diimide dye. The classic perylene diimide dye has been extensively used to construct non-fullerene acceptors, leading to device power conversion efficiencies of over 10%. Strong visible light absorption and deep frontier molecular energy levels have made such materials (both molecular and polymeric) near ideal for pairing with narrow-gap conjugated polymers in bulk-heterojunction active layers. The N-annulation of the dye provides an extra site for side-chain engineering and alters the electronic structure of the polycyclic aromatic core. In addition, N-annulation allows for selective bromination of the perylene core, leading to building blocks that are useful for the construction of large molecular frameworks using the atom-economical direct heteroarylation cross-coupling method. Herein, we detail a series of molecules developed by our team that are based on the N-annulated perylene diimide in the form of dimers with different cores (both electron-rich and electron-deficient); dimers with varied side chains; tetramers with varying geometries; and large, asymmetric molecules with internal energy cascades. The use of these molecules as non-fullerene acceptors in organic photovoltaic devices (binary and ternary blends, outdoor and indoor light applications, and spin-coated vs. slot-die-coated photoactive layers) is presented. Full article

Organic-based photovoltaics are excellent candidates for renewable energy alternatives to fossil fuels due to their low weight, low manufacturing cost, and, in recent years, high efficiency, which is now above 18%. However, one cannot ignore the environmental price of the fabrication procedure due to the usage of toxic solvents and high-energy input equipment. In this work, we report on the enhancement of the power conversion efficiency non-fullerene organic solar cells by incorporating green synthesised Au–Ag nanoparticles, using onion bulb extract, into the hole transport layer poly (3,4-ethylene dioxythiophene)-poly (styrene sulfonate) (PEDOT: PSS) of Poly[4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b;4,5-b′]dithiophene-2,6-diyl-alt-(4-(2-ethylhexyl)-3 fluorothieno[3,4-b]thiophene-)-2-carboxylate-2-6-diyl)]: 3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)-indanone))-5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3-d:2′,3′-d′]-s-indaceno[1,2-b:5,6-b′]dithiophene (PTB7-Th: ITIC) bulk-heterojunction organic solar cells. Red onion has been reported to contain quercetin, which serves as a capping agent that covers bare metal nanoparticles, thus reducing exciton quenching. We found that the optimized volume ratio of NPs to PEDOT: PSS is 0.06:1. At this ratio, a 24.7% enhancement in power conversion efficiency of the cell is observed, corresponding to a 9.11% power conversion efficiency (PCE). This enhancement is due to an increase in the generated photocurrent and a decrease in the serial resistance and recombination, as extracted from the fitting of the experimental data to a non-ideal single diode solar cell model. It is expected that the same procedure can be applied to other non-fullerene acceptor-based organic solar cells, leading to an even higher efficiency with minimal effect on the environment. Full article

Non-fullerene acceptors have recently attracted tremendous interest due to their potential as alternatives to fullerene derivatives in bulk-heterojunction solar cells. Nevertheless, physical understanding of charge carrier generation and transfer mechanism that occurred at the interface between the non-fullerene molecule and donor polymer is still behind their enhanced photovoltaic performance. Here we report examples of a non-planar perylene dimer (TP) as an electron acceptor and achieve a power conversion efficiency of 6.29% in a fullerene-free solar cell. Photoluminescence (PL) measurements show high quenching efficiency driven by the excitons of both conjugated polymer and TP molecule, respectively, indicating efficient electron and hole transfer, which can support a highly intermixed phase of blends measured by atomic force microscopy (AFM) and grazing incident wide-angle X-ray diffraction (GIWAXS). Femtosecond transient absorption spectroscopy (fs-TAS) reveals that the fast exciton dissociation process from TP molecule to donor polymer contributes to additionally increasing current density, leading to stronger incident photon to current efficiency in the visible region. Full article

The influence of P3HT:PCBM ratio on thermal and transport properties of solar cells were determined by photothermal beam deflection spectrometry, which is advantageous tool for non-destructively study of bulk heterojunction layers of organic solar cells. P3HT:PCBM layers of different P3HT:PCBM ratios were deposited on top of PEDOT:PSS/ITO layers which were included in organic bulk-heterojunction solar cells. The thermal diffusivity, energy gap and charge carrier lifetime were measured at different illumination conditions and with a different P3HT:PCBM ratios. As expected, it was found that the energy band gap depends on the P3HT:PCBM ratio. Thermal diffusivity is decreasing, while charge carrier lifetime is increasing with PCBM concentration. Energy band gap was found to be independent on illumination intensity, while thermal diffusivity was increasing and carrier lifetime was decreasing with illumination intensity. The carrier lifetime exhibits qualitatively similar dependence on the PCBM concentration when compared to the open-circuit voltage of operating solar cells under AM1.5 illumination. BDS and standard I-V measurement yielded comparable results arguing that the former is suitable for characterization of organic solar cells. Full article

Three new azomethines based on triphenylamine with two or three substituents were obtained. Chemical structure and purity were confirmed by ¹H NMR, FTIR elemental analysis and mass spectroscopy. The investigations were focused on the relationship between chemical structure and properties important for optoelectronic materials. Thus, the studies of thermal, optical and electrochemical properties were carried out based on differential scanning calorimetry, thermogravimetric analysis, electronic absorption, photoluminescence and cyclic voltammetry measurements. The ongoing consideration of experimental results was complemented by theoretical calculations using the density functional theory method. The donor activity of obtained compounds was tested in bulk-heterojuntion photovoltaic cells with structure ITO/PEDOT:PSS/imine:PCBM/Al and ITO/PEDOT:PSS/imine:P3HT:PCBM/Al). The effect of the presence of the amino-thiophene-3,4-dicarboxylic acid diethyl ester groups and various number of hexyloxyphenyl units on imines properties was demonstrated. Full article