Search Results (7)

Lightweight concrete (LWC) is a long-standing development in the area of construction materials. LWC has become increasingly important for sustainable construction due to its reduced susceptibility to cracking. However, when exposed to extreme temperatures during fires, LWC can lose its compressive strength and ductility. This study investigates the performance of lightweight expanded clay aggregate (LECA) concrete T-beams exposed to elevated temperatures. The research also focuses on the use of an engineered cementitious composite with a basalt fiber-reinforced polymer grid (ECCBFG) as a rehabilitation method for fire-damaged T-beams. Key variables considered include the concrete cover thickness (20 and 30 mm), fire exposure duration (30 and 60 min), and thickness of the ECCBFG layer. Thermocouples were installed at various points within the beams to monitor the heat gradient across the cross-section. Fourteen concrete beam specimens were tested, including control beams, fire-damaged beams, and beams strengthened with the ECCBFG layer. Key performance parameters, such as the energy absorption, cracking load, ductility index, maximum load capacity, and corresponding displacement, were analyzed. The experimental results showed that the strengthened beams outperformed the fire-damaged beams, closely matching the performance of undamaged reference beams in most aspects, except energy absorption. The findings suggest that further research is needed to optimize certain performance indicators and address challenges in strengthening fire-damaged beams. Full article

Compared to glass fiber-reinforced polymer (GFRP) and carbon fiber-reinforced polymer (CFRP), basalt fiber-reinforced polymer (BFRP) offers distinct advantages, including the relatively lower cost and superior creep resistance. As a result, its application in the construction industry has been gaining growing attention. This paper begins by providing an overview of the fundamental background, as well as the mechanical and microscopic properties, of BFs. By exploring various application types, including one-dimensional (e.g., bars, cables), two-dimensional (e.g., grids, sheets), and three-dimensional (e.g., profiles) applications, the research progress of BFRP products in the construction industry is comprehensively summarized. Research has demonstrated the effectiveness of BFRP in a variety of structural applications, such as reinforcing existing structures (e.g., concrete or masonry) using BFRP bars, grids, or sheets, and the development of novel design concepts that integrate BFRP products with existing structural systems. Furthermore, this paper identifies unresolved challenges and proposes potential research directions, intending to promote BFRP’s broader adoption as a standardized and innovative material in the construction industry. Full article

Basalt fiber-reinforced polymers (BFRPs) can reduce construction costs and mitigate corrosion-related issues associated with steel-reinforced concrete structures. There is limited research on completely substituting steel cages with composite material grid structures. Combining BFRP grids with concrete is an effective solution to address the issue of poor corrosion resistance; BFRP grids also have a good bond with steel-reinforced concrete. Therefore, this paper introduces a novel BFRP grid-reinforced concrete beam. Flexural tests indicate that grid frameworks with 3 mm and 5 mm thickness combined with concrete exhibit higher flexural load-bearing capacity. Shear tests show that the shear load-bearing capability is influenced by the shear span ratio. Shear load-bearing capacity decreases when the shear span ratio rises, but only up to a certain point. Theoretical calculations for grid-reinforced concrete beams are made to demonstrate good conformity with test values. Based on the research findings, design recommendations and precise measurements for the internal grid frameworks for composite material grid-reinforced concrete beams are provided. Full article

The use of fabrics in the form of grids embedded in cementitious matrices—usually termed as textile-reinforced mortar, fiber-reinforced cementitious matrix, or textile-reinforced concrete—demonstrate a more stable performance in elevated temperature conditions compared with fiber-reinforced polymers. This study investigated the residual tensile properties of bare yarns and fabrics in the form of grids embedded in a cementitious mortar after exposure to 100 °C, 200 °C, and 300 °C. Three different coated fabric textiles were used as reinforcement: carbon, basalt, and glass. Additionally, scanning electron microscopy (SEM), X-ray diffraction (XRD), and thermos-gravimetric analysis (TGA) were conducted to evaluate potential changes in the internal structure of the fibers and the mortar. The cracking stress, the tensile strength, and the ultimate strain of the composite specimens were increased after exposure to 100 °C, while only carbon and glass fiber grids retained their effectiveness up to 200 °C. At 300 °C, the coupons reinforced with carbon and basalt fibers deteriorated rapidly. Only the glass counterparts showed an improved overall performance due to fiber contraction and the differences in the coating material. The results highlight the differences in the performance of the three fiber types and the important role of the coating material in the overall composite behavior. Full article

This paper presents an experimental study on the tensile behavior of basalt-fiber-grid-reinforced mortar (BGRM) before and after exposure to an elevated temperature of 300 °C considering the effect of fiber grid type, short polyvinyl alcohol fiber (PVA), and high-temperature exposure time. The experimental results show that the mortar plates reinforced with woven textile T25 and fiber-reinforced polymer (FRP) grid G50 exhibited more pronounced strain-hardening behavior. The highest peak stress was obtained for the T25-reinforced plate, which was 85% and 32% higher than that of the T5- and G50-reinforced plates, respectively. Meanwhile, the bridging effect of PVA fibers in mortar can improve the tensile properties. As the high-temperature exposure time increased, the cracking and peak stress of BGRM decreased significantly. Especially for the T5-reinforced plate after exposure to elevated temperature for 2 h, the cracking and peak stress decreased by 60.5% and 38%, respectively. The positive effect of short PVA fibers on the tensile properties of the BGRM became obsolete owing to the melting of short fibers at high temperature. Furthermore, an exponential strength degradation model related to high-temperature exposure time was proposed. Full article

Despite many cases of textile-reinforced engineered cementitious composites (TR-ECCs) for repairing and strengthening concrete structures in the literature, research on lightweight engineered cementitious composites (LECC) combined with large rupture strain (LRS) textile and the effect of textile arrangement on tensile properties is still lacking. Therefore, this paper develops textile-reinforced lightweight engineered cementitious composites (TR-LECCs) with high strain characteristics through reinforcement ratio, arrangement form, and textile type. The study revealed that, by combining an LRS polypropylene (PP) textile and LECC, TR-LECCs with an ultimate strain of more than 8.0% (3–4 times that of traditional TR-ECCs) could be developed, and the PP textile’s utilization rate seemed insensitive to the enhancement rate. The basalt fiber-reinforced polymer (BFRP) textile without epoxy resin coating had no noticeable reinforcement effect because of bond slip; in contrast, the BFRP grid with epoxy resin coating had an apparent improvement in bond performance with the matrix and a better reinforcement effect. The finite element method (FEM) verified that a concentrated arrangement increased the stress concentration in the TR-LECC, as well as the stress value. In contrast, a multilayer arrangement enabled uniform distribution of the stress value and revealed that the weft yarn could help the warp yarn to bear additional tensile loads. Full article

In recent years, even if Fiber Reinforced Polymer (FRP) composites have been widely used for strengthening of civil buildings, a new generation of materials has been studied and proposed for historical masonry construction. These buildings, mainly made of stone work, are common in many areas of Europe and Asia and recent earthquakes has been the cause of many catastrophic failures. The brittleness of unreinforced historic masonry can be considerably reduced using new retrofitting lighter-weight materials such FRP, even if limitations were evidenced due to material and mechanical compatibility with poor substrates. Thus, fibrous reinforcements were used as long fibres incorporated into a cement or lime matrix, which better match with the properties of ancient masonry. The use of low strength fibers such as glass and basalt, respect to carbon, in presence of an alkaline matrix brought out durability issues, due to the chemical vulnerability of common glass and basalt fibres. The objective of this research is to explore the effects of selected aqueous environments and fatigue loading on the mechanical and physical properties of composite grids, made of E-CR (Electrical/Chemical Resistance) glass fibers and epoxy-vinylester resin, used as tensile reinforcement in new composite reinforced mortar systems. Glass-fiber-reinforced polymer (GFRP) coupons were subjected to tensile testing and a severe protocol of durability tests, including alkaline environment and fatigue tensile loads. Accelerated ageing tests were used to simulate long-term degradation in terms of chemical attack and consequent reduction of tensile strength. The ageing protocol consisted of immersion at 40 °C in alkaline bath made by deionized water and Ca(OH)₂, 0.16% in weight, solution for 30 days. GFRP specimens aged and unaged were also tested under tensile fatigue cycles up to 1,000,000 cycles and a nominal frequency of 7.5 Hz. After this severe conditioning the tests indicate a good tensile strength retention of the GFRP in absence of fatigue loads, while a significant loss in fatigue life was experienced when both alkaline exposure and fatigue loads were applied. Full article