Search Results (10)

The vortex tube, also known as the Ranque–Hilsch vortex tube, is a mechanical device that separates compressed gas into hot and cold streams. It offers a reliable and cost-effective solution to a wide range of cooling applications, as it operates without moving parts, electricity, or refrigerants. Research on vortex tubes has primarily focused on understanding the mechanisms of energy separation and optimizing cooling performance by altering geometric operational parameters. In this study, a Computation Fluid Dynamics (CFD) analysis was conducted to enhance the prediction of energy separation performance and improve the overall energy efficiency of the vortex tube. First, the geometry of the experimental device was modeled to closely match its actual shape, unlike the simplified geometries commonly used in previous CFD studies. Simulations were then carried out with variation in grid systems and turbulence models, and the results demonstrated improved agreement with experimental data compared to those reported in previous studies. Finally, simulations with a modified shape of the inlet nozzle shape were performed, revealing that the energy separation effect of the vortex tube could be enhanced by approximately 15% with an increased inlet expansion ratio ($ϵ$) while maintaining a constant nozzle length. Full article

To combat climate change successfully, enhancing existing processes is imperative alongside exploring new regenerative technologies. For this purpose, new components must be considered to improve the efficiency of thermodynamic processes. A promising candidate is the Ranque–Hilsch vortex tube due to its low investment cost and maintenance. Previous research has highlighted the thermodynamic advantages of employing a vortex tube in various applications, such as Brayton cycles or as a replacement for conventional expansion valves. However, to assess the potential of the vortex tube within a thermodynamic process, a computationally efficient but precise model of the vortex tube is required. Existing modeling approaches often fail to accurately predict experimental trends or require information such as geometry data that are not available for potential analyses. Thus, the present study proposes a novel thermodynamic-based black-box modeling approach: the vortex tube efficiency is introduced by incorporating operating and geometrical conditions into a single parameter. The vortex tube efficiency is systematically investigated for different operating conditions and various fluids and compared with available experimental results. The resulting modeling approach allows the qualitative and quantitative prediction of vortex tube behavior for air at various operating pressures and cold gas fractions. Further experimental investigations are required for a comprehensive quantitative description of vortex tubes with different geometries and working fluids. Full article

The aerospace metal cutting industry’s search for environmentally friendly practices that do not compromise machining performance is well known. One of the major objectives is the reduction in use of cutting fluids, which play a major role in containing the harsh effects of severe heat generated during machining. Machining performance and product quality can be improved by controlling heat during machining. The purpose of this study was to determine the effectiveness of various environmentally friendly metalworking fluid (MF) strategies for the sustainable turning of aerospace aluminum alloy (Al-5.6Zn-2.5Mg-1.6Cu-0.23Cr-T6) for automotive, marine, and aerospace industrial applications. The SEM images were analyzed for worn tool surfaces and machined surfaces. Under dry conditions, heat does not dissipate well, and will enter the workpiece due to the absence of coolant. This causes extreme damage beneath a turned workpiece. Thus, at 10 µm, a drop in microhardness of approximately 20% can be observed. A similar observation was made in a Ranque-Hilsch vortex tube (RHVT) and in compressed air; however, the drop in hardness was relatively low compared to dry conditions. This evaluation of microhardness indicated a heat-based attention in the turned workpiece, and thus, the heat-based effect was found to be lowest in RHVT and compressed air compared to dry conditions. Results showed that RHVT reduces temperature up to 10%, surface roughness 13%, and tool wear 20% compared to dry turning. Overall, RHVT was identified as more effective environmentally friendly cooling strategy than dry and compressed air for the turning of aluminum alloy 7075-T6. Full article

Preheating is often required to prevent hydrate formation during the pressure reduction process in a natural gas distribution network’s pressure reduction station. This paper examines an energy recovery method to avoid the cost and energy consumption of this preheating. The primary aim is to assess the techno-economic feasibility of an energy recovery system based on the Ranque–Hilsch vortex tube coupled to a heat exchanger for large-scale application to the gas grid. To this end, a techno-economic model of the entire energy recovery system was included in an optimisation procedure. The resulting design minimises the payback period (PP) when the system is applied to the pressure reduction stations belonging to a particular gas grid. The pressure reduction stations always operate at an outlet pressure above atmospheric pressure. However, available performance models for the Ranque–Hilsch vortex tube do not permit prediction at backpressure operation. Therefore, a novel empirical model of the device is proposed, and a cost function derived from several manufacturer quotations is introduced for the first time, to evaluate the price of the Ranque–Hilsch vortex tubes. Finally, a nearly complete set of pressure reduction stations belonging to the Italian natural gas grid was chosen as a case study using actual operating parameters collected by each station’s grid manager. The results indicate that the environmental temperature strongly affects the technical and economic feasibility of the proposed energy recovery system. In general, pressure reduction stations operating at an ambient temperature above 0 °C are economically desirable candidates. In addition, the higher the energy recovery system convenience, the higher the flow rate and pressure drop managed by the station. In the Italian case study, 95% of preheating costs could be eliminated with a PP of fewer than 20 years. A 40% preheating cost saving is still possible if the maximum PP is limited to 10 years, and a small but non-negligible 3% of preheating costs could be eliminated with a PP of fewer than 4.5 years. Full article

Despite the application of vortex tubes for cooling, separating gas mixtures, vacuuming, etc., the mechanism of energy separation in vortex tubes remains an object of discussion. This paper studies the effect of secondary swirling in supersonic flows on the energy separation of monatomic and diatomic gases. The approach used is a numerical solution of the Reynolds-averaged Navier-Stokes equations, closed by the Reynolds Stress Model turbulence model. The modelling provided is for a self-vacuuming vortex tube with air, helium, argon, and carbon dioxide. According to the results of the calculations, the effect of secondary swirling is inherent only in viscous gases. A comparison was made between obtained total temperature difference, the level of secondary swirling and power losses on expansion from the nozzle, compression shocks, friction, turbulence, and energy costs to develop cascaded swirl structures. Our results indicate that helium and argon have the highest swirling degree and, consequently, the highest energy separation. Moreover, it can be concluded that the power costs on the development of cascaded vortex structures have a significant role in the efficiency of energy separation. Full article

Improving efficiency of hydrogen cooling in cryogenic conditions is important for the wider applications of hydrogen energy systems. The approach investigated in this study is based on a Ranque-Hilsch vortex tube (RHVT) that generates temperature separation in a working fluid. The simplicity of RHVT is also a valuable characteristic for cryogenic systems. In the present work, novel shapes of RHVT are computationally investigated with the goal to raise efficiency of the cooling process. Specifically, a smooth transition is arranged between a vortex chamber, where compressed gas is injected, and the main tube with two exit ports at the tube ends. Flow simulations have been carried out using STAR-CCM+ software with the real-gas Redlich-Kwong model for hydrogen at temperatures near 70 K. It is determined that a vortex tube with a smooth transition of moderate size manifests about 7% improvement of the cooling efficiency when compared vortex tubes that use traditional vortex chambers with stepped transitions and a no-chamber setup with direct gas injection. Full article

The present work shows the process for MoS₂ nanosheet production by liquid N₂-queched bulk, a novel method having highly efficient, green, and facile operation. The produced MoS₂ nanoparticles are suspended in minimum quantity cooling lubrication (MQCL)-based fluid to form nanofluid used for the hard milling of AISI D2 steel. The study aims to improve the hard-milling performance assisted by the MQCL technique using MoS₂ nanofluid. ANOVA analysis is used to evaluate the effects of three input machining variables, including nanoparticle concentration, cutting speed, and material hardness on cutting forces. The results indicate that the better cooling effect from the principle of the Ranque–Hilsch vortex tube of the MQCL device combined with the better lubricating performance from MoS₂ nanofluid brings out the sustainable alternative solution for machining difficult-to-cut material. Moreover, the experimental results provide the technical guides for the selection of proper values of nanoparticle concentration and cutting speed while ensuring the technological, economic, and environmental characteristics. Full article

This study is focused on the application of a cooling compressed air system in drilling processes; this environmentally friendly technique allows removing material at very low temperatures, approximately up to −22 °C in the cutting area. The main goals are to find the most improve cutting conditions with less energy consumption, for the drilling of reinforced polyether-ether-ketone with glass fiber at 30% (PEEK-GF30) with cooling compressed air by a Ranque-Hilsch vortex tube, and to find a balance between environmental conditions and adequate process performance. Drilling tests were carried out on plates of PEEK-GF30 to analyze the influence of cutting parameters and environmental temperature (–22, 0 and 22 °C) on variables such as thrust forces, energy and material removed rate by the use of statistical methods; analysis of variance, analysis of means, response surface, and desirability function were employed to identify the optimum region that provides the most improved values of the aforementioned variables. Drill bit diameter was also analyzed to determine the quality of drilled holes. During the drilling processes, force signals were detected by a piezoelectric dynamometer connected to multichannel amplifier and a pyrometer was used to control the temperature. The diameters of the drilled holes were measured by a coordinate measuring machine. Cooling compressed air can be considered an adequate technique to improve the results from an environmental and efficient perspective; in particular, the maximum desirability function was found at a spindle speed of 7000 rpm, a feedrate of 1 mm/rev and a temperature close to −22 °C. Full article

The present work shows an experimental investigation on the effect of minimum quantity cooling lubrication (MQCL) during hard milling of SKD 11 tool steel (52–60HRC). The novelty here lies on the use of MQCL technique, which comprises the cooling strategy based on the principle of Ranque-Hilsch vortex tube and MQL method. Moreover, MoS₂ nanoparticles are suspended in MQCL based fluid to improve the lubricating character. The response parameters, including surface roughness, surface microstructure, and surface profile are studied. The obtained results show that MQCL using nanofluid gives out better surface quality compared to dry, MQL, and MQCL with pure fluid. Also, the different concentrations of MoS₂ nanoparticles are investigated to find out the optimized value as well as the interaction effect on machined surface. Full article

Environmental protection is the major concern of any form of manufacturing industry today. As focus has shifted towards sustainable cooling strategies, minimum quantity lubrication (MQL) has proven its usefulness. The current survey intends to make the MQL strategy more effective while improving its performance. A Ranque–Hilsch vortex tube (RHVT) was implemented into the MQL process in order to enhance the performance of the manufacturing process. The RHVT is a device that allows for separating the hot and cold air within the compressed air flows that come tangentially into the vortex chamber through the inlet nozzles. Turning tests with a unique combination of cooling technique were performed on titanium (Grade 2), where the effectiveness of the RHVT was evaluated. The surface quality measurements, forces values, and tool wear were carefully investigated. A combination of analysis of variance (ANOVA) and evolutionary techniques (particle swarm optimization (PSO), bacteria foraging optimization (BFO), and teaching learning-based optimization (TLBO)) was brought into use in order to analyze the influence of the process parameters. In the end, an appropriate correlation between PSO, BFO, and TLBO was investigated. It was shown that RHVT improved the results by nearly 15% for all of the responses, while the TLBO technique was found to be the best optimization technique, with an average time of 1.09 s and a success rate of 90%. Full article