Search Results (10)

New materials for additive manufacturing are currently being actively studied, which both have the necessary physicochemical properties and are safe for the environment and living organisms. We have proposed a simple process for the production of composite materials based on a transparent polymethyl methacrylate-like photopolymer resin modified with metallic titanium nanoparticles. Standardized plate samples were printed from the obtained modified photopolymer resins using mask stereolithography with an LED light source array (MSLA), and their mechanical properties were evaluated. Plates were also printed, for which the surface topology, distribution of nanoparticles in the polymer matrix, chemical structure, optical properties, chemical structure, and optical properties were characterized. In the context of the impact on biological systems, the ability of materials to enhance the formation of ROS and affect the main biomacromolecules was demonstrated. At the same time, the developed composite materials inhibit the growth of E. coli bacterial cells, and the bactericidal effect of the surfaces of the obtained materials was shown. Despite the significant antibacterial properties of the synthesized materials, no negative impact on the growth and development of adhesive cultures of eukaryotic cells in vitro was detected. Full article

Background/Objectives: Endodontically treated molars are structurally weakened due to internal tissue loss, increasing their risk of fracture. Endocrowns, developed as a conservative alternative to post–core systems, have gained popularity with the rise of digital dentistry, CAD/CAM workflows, and 3D-printed restorations. In this context, the aim of the present pilot study was to investigate the influence of cement layer thickness, intracoronal depth, and dentine wall thickness on the fracture resistance of molars restored with 3D-printed endocrowns. Methods: Twelve extracted human molars were endodontically treated and restored with endocrowns fabricated from a 3D-printed resin material, SprintRay Crown^TM (SprintRay Inc. Los Angeles, CA, USA), via masked stereolithography (MSLA) on a Prusa SL1 printer. Cementation was performed using RelyX Universal Resin Cement (3M, Maplewood, MN USA). Cone beam computed tomography (CBCT) was used to measure the dentine thickness and intracoronal depth before cementation and cement thickness after cementation. The fracture resistance was evaluated using a universal testing machine. For each variable (Td, Dp, Tc), the 12 specimens were divided into two groups (n = 6). Statistical analysis included Pearson correlation, a one-way ANOVA, and the non-parametric Mann–Whitney U test. Results: Within the limitations of this pilot in vitro study, cement thickness demonstrated a strong positive correlation with fracture resistance (r = 0.577) and was the only variable showing statistical significance in the ANOVA (F = 7.847, p = 0.019). In contrast, intracoronal depth and dentine wall thickness exhibited weaker and nonsignificant correlations. No significant mechanical advantage was observed from increasing the pulp chamber depth or peripheral dentine wall thickness. This result was further supported by nonparametric Mann–Whitney U testing (p = 0.015). Conclusions: Cement layer thickness is a key biomechanical factor influencing the fracture resistance of endocrown restorations. Preparation depth and dentine wall geometry appear to have a less direct impact. Full article

The development of microtextures has had a transformative impact on surface design in engineering, leading to substantial advancements in the performance, efficiency, and functionality of components and tools. This study presents an innovative methodology for fabricating SEDM electrodes. The methodology combines additive manufacturing by mask stereolithography with an optimized electroforming process to obtain high-precision copper shells. A key aspect of the study involved redesigning the electroforming equipment, enabling the independent examination of critical variables such as anode–cathode distance and electrolyte recirculation. This approach allowed precise analysis of their impact on metal deposition. This redesign enabled the assessment of the impact of electrolyte recirculation on the quality of the shells obtained. The findings indicate that continuous recirculation at 60% power effectively reduced thickness deviation by up to 32.5% compared to the worst-case scenario, achieving average thicknesses within the functional zone of approximately 110 µm. In contrast, the absence of flow or excessive turbulence did not generate defects such as unfilled zones or non-uniform thicknesses. The shells obtained were validated as functional tools in SEDM, demonstrating their viability for the generation of textures with high geometric fidelity. This approach optimizes the manufacturing of textured electrodes and opens new opportunities for their application in advanced industrial processes, providing a more efficient and sustainable alternative to conventional methods. Full article

Masked Stereolithography (mSLA) is an additive manufacturing technique that has been recently explored. Currently, studies in the literature addressing the investigation of stress concentrators in photosensitive resin parts printed on mSLA devices using the Whitney–Nuismer analytical method combined with Finite Element Analysis (FEA) and Digital Image Correlation (DIC) are rare. This work utilizes the combination of these techniques to analyze stress concentrators in specimens subjected to axial and eccentric loads, considering the effects imposed by the clamp restraint and a complementary study considering the free loading condition. For axial loading, the results are consistent, with variations in the stress concentration factor ranging from 0.42% to 5.25%. For the eccentric loading studies, the results indicate that the most suitable method for the test was the analysis considering the restraint imposed by the clamp, as the deformation results show a maximum error of 6.9% compared to 24.7% when the restraints were disregarded. The consistency of the results reinforces the quality of the employed technique, demonstrating that this study not only achieved its objectives but also provided a foundation for future investigations in the field. Full article

The zygomatic bone area experiences frequent mechanical damage in the middle craniofacial region, including the orbital floor. The orbital floor bone is very thin, ranging from 0.74 mm to 1.5 mm. Enhancing digitization, reconstruction, and CAD modeling procedures is essential to improving the visualization of this structure. Achieving a homogeneous surface with high manufacturing accuracy is crucial for developing precise surgical models and tools for creating titanium mesh implants to reconstruct the orbital floor geometry. This article improved the accuracy of reconstruction and CAD modeling using the example of the development of a prototype implant to replace the zygomatic bone and a tool to form the geometry of the titanium mesh within the geometry of the orbital floor. The masked stereolithography (mSLA) method was used in the model manufacturing process because it is low-cost and highly accurate. Two manufacturing modes (standard and ultra-light) were tested on an Anycubic Photon M3 Premium 3D printer to determine which mode produced a more accurate representation of the geometry. To verify the geometric accuracy of the manufactured models, a GOM Scan1 structured light scanner was used. In the process of evaluating the accuracy of the model preparation, the maximum deviation, mean deviation, range and standard deviation were determined. The maximum deviations for anatomical structures created using the normal mode ranged from ±0.6 mm to ±0.7 mm. In contrast, models produced with the ultra-light mode showed deviations of ±0.5 mm to ±0.6 mm. Furthermore, the results indicate that the ultra-light mode offers better surface accuracy for die and stamp models. More than 70% of the surface of the models is within the deviation range of ±0.3 mm, which is sufficient for planning surgical procedures. However, the guidelines developed in the presented publication need to optimize the CAD process and select 3D-printing parameters to minimize deviations, especially at the edges of manufactured models. Full article

This study presents an experimental and numerical investigation into the stress field in cylinders manufactured from photosensitive resin using the Masked Stereolithography (MSLA) technique. For material characterization, tensile and bending test data from resin specimens were utilized. The stress field in resin disks was experimentally analyzed using photoelasticity and Digital Image Correlation (DIC) methods, subjected to compressive loads, according to the cylinder–plane contact model. Images were captured during the experiments using polarizing film and a low-cost CPL lens, coupled to a smartphone. The experimental results were compared with numerical and analytical simulations, where the formation of fringes and regions indicating the direction and magnitude of normal and shear stresses were observed, with variations ranging from 0.6% to 8.2%. The convergence of the results demonstrates the feasibility of using parts produced with commercially available photosensitive resin on non-professional printers for studying contact theory and stress fields. In the future, this methodology is intended to be applied to studies on stress in gears. Full article

Stereolithography based 3D printing of microfluidics for prototyping has gained a lot of attention due to several advantages such as fast production, cost-effectiveness, and versatility over traditional photolithography-based microfabrication techniques. However, existing consumer focused SLA 3D printers struggle to fabricate functional microfluidic devices due to several challenges associated with micron-scale 3D printing. Here, we explore the origins and mechanism of the associated failure modes followed by presenting guidelines to overcome these challenges. The prescribed method works completely with existing consumer class inexpensive SLA printers without any modifications to reliably print PDMS cast microfluidic channels with channel sizes as low as ~75 μm and embedded channels with channel sizes as low ~200 μm. We developed a custom multi-resin formulation by incorporating Polyethylene glycol diacrylate (PEGDA) and Ethylene glycol polyether acrylate (EGPEA) as the monomer units to achieve micron sized printed features with tunable mechanical and optical properties. By incorporating multiple resins with different mechanical properties, we were able to achieve spatial control over the stiffness of the cured resin enabling us to incorporate both flexible and rigid components within a single 3D printed microfluidic chip. We demonstrate the utility of this technique by 3D printing an integrated pressure-actuated pneumatic valve (with flexible cured resin) in an otherwise rigid and clear microfluidic device that can be fabricated in a one-step process from a single CAD file. We also demonstrate the utility of this technique by integrating a fully functional finger-actuated microfluidic pump. The versatility and accessibility of the demonstrated fabrication method have the potential to reduce our reliance on expensive and time-consuming photolithographic techniques for microfluidic chip fabrication and thus drastically lowering our barrier to entry in microfluidics research. Full article

The combination of printed circuit boards (PCB) and microfluidics has many advantages. The combination of electrodes, sensors and electronics is needed for almost all microfluidic systems. Using PCBs as a substrate, this integration is intrinsic. Additive manufacturing has become a widely used technique in industry, research and by hobbyists. One very promising rapid prototype technique is vat polymerization with an LCD as mask, also known as masked stereolithography (mSLA). These printers are available with resolutions down to 35 µm, and they are affordable. In this paper, a technology is described which creates microfluidics on a PCB substrate using an mSLA printer. All steps of the production process can be carried out with commercially available printers and resins: this includes the structuring of the copper layer of the PCB and the buildup of the channel layer on top of the PCB. Copper trace dimensions down to 100 µm and channel dimensions of 800 µm are feasible. The described technology is a low-cost solution for combining PCBs and microfluidics. Full article

Germplasm repositories can benefit sustainable aquaculture by supporting genetic improvement, assisted reproduction, and management of valuable genetic resources. Lack of reliable quality management tools has impeded repository development in the past several decades. Microfabricated open-hardware devices have emerged as a new approach to assist repository development by providing standardized quality assessment capabilities to enable routine quality control. However, prototyping of microfabricated devices (microdevices) traditionally relies on photolithography techniques that are costly, time intensive, and accessible only through specialized engineering laboratories. Although resin 3-D printing has been introduced into the microfabrication domain, existing publications focus on customized or high-cost (>thousands of USD) printers. The goal of this report was to identify and call attention to the emerging opportunities to support innovation in microfabrication by use of low-cost (<USD 350) resin 3-D printing for rapid prototyping. We demonstrate that low-cost mask-based stereolithography (MSLA) 3-D printers with straightforward modifications can provide fabrication quality that approaches traditional photolithography techniques. For example, reliable feature sizes of 20 µm with dimensional discrepancy of <4% for lateral dimensions and <5% for vertical dimensions were fabricated with a consumer-level MSLA printers. In addition, alterations made to pre-processing, post-processing, and printer configuration steps improved print quality as demonstrated in objects with sharper edges and smoother surfaces. The prototyping time and cost of resin 3-D printing (3 h with USD 0.5/prototype) were considerably lower than those of traditional photolithography (5 d with USD 80/prototype). With the rapid advance of consumer-grade printers, resin 3-D printing can revolutionize rapid prototyping approaches for microdevices in the near future, facilitating participation in interdisciplinary development of innovative hardware to support germplasm repository development for aquatic species. Full article

The article discusses the influence of the post-process on the mechanical properties of elements produced with the use of the mask stereolithography (mSLA) method. Printed samples were subjected to the following post-process steps: Washing and post-curing, at various times. Then, static tensile and static bending tests were carried out, as well as Shore D hardness measurements for the inner and surface part of the sample, as well as profilographometric analysis of the surface. The post-curing time has been found to strongly affect the tensile and bending strength of printouts, and to improve their surface quality. Washing has an ambiguous effect on the strength of the printouts, but, in the end, it was found that extended washing slightly reduces the strength. Washing significantly affects the quality of the printout surface. A washing time that is too short results in a surface that strongly resembles the printing process, with high roughness. Increasing the washing time to 10 min lowers the roughness by one order of magnitude. Post-curing has also been shown to be beneficial for the cured sample with the application of shielding water. This approach results in an improvement in the flexural strength of the printouts. In general, the obtained research results indicate that, for printouts with cross-sectional dimensions of several mm, the optimal washing time is no more than 10 min and the post-curing time is at least 30 min. Full article