Search Results (8)

Recent years have witnessed a surge in the research of memristors as fundamental building blocks for neuromorphic computing, owing to their exceptional ability to emulate the plastic behavior of biological synapses in a high-density, low-power hardware format. These devices are increasingly recognized as the key to achieving efficient artificial neural networks. Two-dimensional (2D) molybdenum disulfide (MoS₂) is a premier candidate for artificial synapses due to its atomic scale and tunable electronic properties. However, achieving wafer-scale MoS₂ thin films for integrated memristor systems remains a significant challenge. In this work, a scalable strategy combining cetyltrimethylammonium bromide (CTAB)-assisted electrochemical intercalation and oil–water interface self-assembly was developed to fabricate large-area 2H-phase MoS₂ thin films. Leveraging the amphiphilic nature of CTAB-functionalized MoS₂ nanosheets, continuous Janus-structured MoS₂ films with asymmetric wetting properties (hydrophilic vs. hydrophobic) were successfully prepared. Vertical-structured Ag/Janus-structured MoS₂/ITO memristors demonstrated robust non-volatile switching with high endurance and long-term retention. The devices successfully emulated biological synaptic behaviors, including short-term and long-term plasticity. Furthermore, the memristors exhibited distinct optoelectronic synergistic modulation under 405 nm illumination, enabling light-sensitive synaptic functions. This work offers a versatile interface engineering route for low-power integrated sensing–memory–computing hardware. Full article

Aiming at the characteristics of high viscosity and poor fluidity of high waxy ordinary heavy oil, a Janus silica-based nanosheet composite viscosity reducer was designed and prepared in this paper. The viscosity reducer was assembled by asymmetric Gemini viscosity reducer and silica nanosheets through dehydration condensation reaction, and its structure was verified by FT-IR, ¹HNMR, XPS and DLS. The viscosity reduction performance, emulsion stability, interfacial tension and flow performance of the viscosity reducer were systematically evaluated by taking heavy oil with wax content of 35.7% and viscosity of 237 mPa·s at 30 °C as the research object. The results showed that, at an oil-to-viscosity-reducer-solution volume ratio of 3:7 and a viscosity reducer mass fraction of 0.3%, the maximum viscosity reduction rate reached 94.5% at 30 °C, calculated relative to the viscosity of the dehydrated original heavy oil. The oil–water interfacial tension was significantly reduced, and the 24 h bleeding ratio, defined as the volume percentage of separated water relative to the initial aqueous phase volume, was only 7.3%, indicating good emulsion stability. The core flow experiment shows that the resistance coefficient is reduced to the lowest at 0.3% concentration, and the seepage capacity is significantly improved. The analysis of total hydrocarbon gas chromatography showed that the content of high-carbon wax components in the C₂₃-C₃₀ range decreased by 4.79 percentage points after treatment, indicating that the viscosity reducer preferentially interacted with high-carbon wax molecules and promoted wax-crystal dispersion, thereby weakening the three-dimensional wax-crystal network. The viscosity reducer has the synergistic effect of dispersing wax crystals, reducing interfacial tension and stabilizing emulsification, which provides a low-cost and high-performance technical approach for the efficient exploitation of high waxy ordinary heavy oil. Full article

In this study, patch-structured C₈/CHO template microspheres were successfully synthesized through in situ reduction and sol–gel reactions, providing a reusable platform for subsequent modifications. Based on these templates, temperature-responsive PW₁₂O₄₀³⁻-PILs/PNIPAM Janus nanosheets were prepared via sequential Schiff-base coupling and ATRP. Structural characterizations (XRD, SEM, TEM, FTIR, and TGA) confirmed successful functionalization and nanosheet formation. The PNIPAM moiety endowed the nanosheets with temperature responsiveness, while the incorporation of polymerized ionic liquids and phosphotungstate anions further enhanced amphiphilicity and dispersion stability. When applied as particulate emulsifiers in water/toluene systems, the Janus nanosheets formed stable Pickering emulsions at elevated temperatures and underwent reversible emulsification–demulsification upon temperature cycling. These findings demonstrate the potential of PW₁₂O₄₀³⁻-PILs/PNIPAM Janus nanosheets as smart emulsifiers for responsive separation and formulation technologies. Full article

Our experiment revealed that the addition of Janus nanosheets to polypropylene (PP) has a significant impact on the viscoelasticity of the composite system. Specifically, when 0.10 wt% of Janus nanosheets were added, the complex viscosity of the composite system increased. However, when we added less than 0.05 wt% of Janus nanosheets, there was a reduction in complex viscosity, which is known as the non-Einstein phenomenon. The Cole–Cole plot showed that the nanosheet network structure did not have a significant effect on the viscosity of the composite system. Additionally, we used carbon dioxide as a foaming agent to autoclave foaming using modified PP from Janus nanosheets, and the results demonstrated that increasing the number of Janus nanosheets decreased the apparent density and strengthened the cell structure of foaming beads, resulting in improved closed porosity. Full article

To meet the increasing global demand for energy, better recovery of crude oil from reservoirs must be achieved using methods that are economical and environmentally benign. Here, we have developed a nanofluid of amphiphilic clay-based Janus nanosheets via a facile and scalable method that provides potential to enhance oil recovery. With the aid of dimethyl sulfoxide (DMSO) intercalation and ultrasonication, kaolinite was exfoliated into nanosheets (KaolNS) before being grafted with 3-methacryloxypropyl-triemethoxysilane (KH570) on the Alumina Octahedral Sheet at 40 and 70 °C to form amphiphilic Janus nanosheets (i.e., KaolKH@40 and KaolKH@70). The amphiphilicity and Janus nature of the KaolKH nanosheets have been well demonstrated, with distinct wettability obtained on two sides of the nanosheets, and the KaolKH@70 was more amphiphilic than the KaolKH@40. Upon preparing Pickering emulsion in a hydrophilic glass tube, the KaolKH@40 preferentially stabilized emulsions, while the KaolNS and KaolKH@70 tended to form an observable and high-strength elastic planar interfacial film at the oil–water interface as well as films climbing along the tube’s surface, which were supposed to be the result of emulsion instability and the strong adherence of Janus nanosheets towards tube’s surface. Subsequently, the KaolKH was grafted with poly(N-Isopropylacrylamide) (PNIPAAm), and the prepared thermo-responsive Janus nanosheets demonstrated a reversible transformation between stable emulsion and the observable interfacial films. Finally, when the samples were subjected to core flooding tests, the nanofluid containing 0.01 wt% KaolKH@40 that formed stable emulsions showed an enhanced oil recovery (EOR) rate of 22.37%, outperforming the other nanofluids that formed observable films (an EOR rate ~13%), showcasing the superiority of Pickering emulsions from interfacial films. This work demonstrates that KH-570-modified amphiphilic clay-based Janus nanosheets have the potential to be used to improve oil recovery, especially when it is able to form stable Pickering emulsions. Full article

Various nanoparticles have been applied as chemical demulsifiers to separate the crude-oil-in-water emulsion in the petroleum industry, including graphene oxide (GO). In this study, the Janus amphiphilic graphene oxide (JGO) was prepared by asymmetrical chemical modification on one side of the GO surface with n-octylamine. The JGO structure was verified by Fourier-transform infrared spectra (FTIR), transmission electron microscopy (TEM), and contact angle measurements. Compared with GO, JGO showed a superior ability to break the heavy oil-in-water emulsion with a demulsification efficiency reaching up to 98.25% at the optimal concentration (40 mg/L). The effects of pH and temperature on the JGO’s demulsification efficiency were also investigated. Based on the results of interfacial dilatational rheology measurement and molecular dynamic simulation, it was speculated that the intensive interaction between JGO and asphaltenes should be responsible for the excellent demulsification performance of JGO. This work not only provided a potential high-performance demulsifier for the separation of crude-oil-in-water emulsion, but also proposed novel insights to the mechanism of GO-based demulsifiers. Full article

A heterogeneous Janus-type palladium interphase catalyst was obtained by selective surface modification of a hollow mesoporous silica material. The catalyst comprises hydrophobic octyl groups on one side of the silica nanosheets and single-site bis-imidazoline dichlorido palladium(II) complexes on the other. The structure of this composite material has been analyzed by means of elemental analysis, atomic absorption spectroscopy, BET surface analysis, TGA, SEM and solid-state CP-MAS ¹³C and ²⁹Si NMR spectroscopy. The catalyst showed extraordinary activity for the aqueous-phase oxidation of styrene to acetophenone using 30% hydrogen peroxide as the oxidant. An 88% yield of acetophenone could be achieved after 60 min. Full article

Surface-templated evaporation driven (STED) method is a promising method to fabricate supraparticles with various sizes, porosities, and shapes by drying colloidal dispersion drops on liquid repellent surfaces. Until now, for the method, only spherical shaped colloidal particles have been used as primary colloids. Here, we introduce six different shapes of nano-colloidal dispersions for the STED method: nanocubics, nanoplates, nanosheets, coffin-shaped nanoparticles (NPs), spherical NPs, and aggregates of NPs. It is confirmed that the shape and size of the primary colloids have little effect for drying the dispersion drop when a single component colloidal dispersion is dried. For heterogeneous supraparticles with composite material assembly, still the shape of the colloids has no influences, while the size and dispersity play roles for tuning the morphology of the supraparticles. From the results, we propose a way to fabricate homogeneous mixture, core/shell, and Janus core/shell structures of the supraparticles depending on the size and dispersity of the mixture colloidal dispersion. Indeed, knowledge on the effects of types of colloids would be of great importance for tailoring supraparticles. Full article