Search Results (15)

In this study, the solidification behavior of 310S stainless steel was systematically investigated by combining high-temperature confocal laser scanning microscopy (HT-CLSM), microstructural characterization, and thermodynamic calculations. The focus was on the formation and transformation of ferrite, secondary-phase precipitation, and elemental segregation behavior, with comparisons made with 304 stainless steel. The effects of an Al addition and cooling rate were also explored. The results show that the solidification sequence of 310S stainless steel is L → L + γ → L + γ + δ → δ + γ, in which austenite nucleates early and grows rapidly, followed by the precipitation of a small amount of δ-ferrite in the later stages of solidification. In contrast, 304 stainless steel solidifies according to L → L + δ → L + δ + γ → δ + γ, with a rapid δ → γ transformation occurring after solidification. Compared with 304, 310S stainless steel exhibits a reduced ferrite fraction and a significantly increased σ phase content. The σ phase primarily precipitates directly from δ-ferrite (δ → σ), while M₂₃C₆ preferentially forms at grain boundaries and δ/γ interfaces, where δ-ferrite not only provides fast diffusion pathways for Cr but also nucleation sites. The solidification segregation sequence in 310S stainless steel is Cr > Ni > Fe, with Cr and Ni showing positive segregation and Fe showing negative segregation. The addition of Al does not alter the solidification mode of 310S stainless steel but refines austenite grains, reduces interdendritic solute enrichment, decreases segregation, lowers both the size and fraction of ferrite, and suppresses the precipitation of σ and M₂₃C₆ phases. This effect is mainly attributed to the reduction of δ/γ interfaces, which weakens the preferred nucleation sites for M₂₃C₆. Increasing the cooling rate enhances non-equilibrium solute segregation, promotes ferrite formation, inhibits the δ → γ transformation, and ultimately retains more ferrite; the intensified segregation further accelerates the δ → σ transformation. Full article

The growth behavior of austenite grains in ADB790E hydropower steel under the synergistic effects of heating temperature and holding time was studied using in situ quenching and an in situ high-temperature confocal laser scanning microscope (HT-CLSM) system. The experimental results indicate that the size of the austenite grains exhibits a significant coarsening trend as the heating temperature increases and the holding time extends. Based on the experimental data, the Beck’s model and Sellars’ model for austenite grain growth were constructed and compared and analyzed. The predicted grain size values obtained by the models have a strong correlation with the experimental measured values. To verify the accuracy of the model, the predicted values of the model were compared with the in situ observations of HT-CLSM. The results were highly consistent, effectively revealing the growth law of austenite grains of this steel grade during the thermal cycling process. Full article

The continuous casting of Ti-Nb microalloyed steel was simulated with high temperature confocal laser scanning microscopy (HTCLSM). Evolution of the sample surface morphology was observed in-situ, during cooling conditions chosen to represent different locations in a cast slab. Calculations with a thermodynamics model of carbonitride precipitate formation agreed with the transmission electron microscopy (TEM) analysis that fine reliefs observed on the sample surface were actually caused by interior precipitation of (Ti,Nb)(C,N). Precipitation and the resulting reliefs changed with location beneath the slab surface, simulated casting speed, and steel composition. With the same casting speed and steel composition, reliefs in the simulated slab surface sample appeared earlier and were larger than in the slab center. With increased casting speed, reliefs were observed later and decreased in size. With increased titanium or niobium content, reliefs appeared earlier and increased in number. TEM measurement showed that the precipitate diameters were mainly smaller than 4 nm, with a few between 4 and 8 nm. The property of surface reliefs observed via HTCLSM correlated qualitatively with the number and size of internal precipitates measured with TEM, showing this to be an effective tool for indirectly characterizing nanoscale secondary phase precipitation inside the sample. Full article

This study focuses on S32654 super austenitic stainless steel (SASS) and systematically characterizes the morphology of the sigma (σ) phase and the segregation behavior of alloying elements in its as-cast microstructure. High-temperature confocal scanning laser microscopy (HT-CSLM) was employed to investigate the effect of the rare earth element yttrium (Y) on the solidification microstructure and σ phase precipitation behavior of SASS. The results show that the microstructure of SASS consists of austenite dendrites and interdendritic eutectoid structures. The eutectoid structures mainly comprise the σ phase and the γ₂ phase, exhibiting lamellar or honeycomb-like morphologies. Regarding elemental distribution, molybdenum displays a “concave” distribution pattern within the dendrites, with lower concentrations at the center and higher concentrations at the sides; when Mo locally exceeds beyond a certain threshold, it easily induces the formation of eutectoid structures. Mo is the most significant segregating element, with a segregation ratio as high as 1.69. The formation mechanism of the σ phase is attributed to the solid-state phase transformation of austenite (γ → γ₂ + σ). In the late stages of solidification, the concentration of chromium and Mo in the residual liquid phase increases, and due to insufficient diffusion, there are significant compositional differences between the interdendritic regions and the matrix. The enriched Cr and Mo cause the interdendritic austenite to become supersaturated, leading to solid-state phase transformation during subsequent cooling, thereby promoting σ phase precipitation. The overall phase transformation process can be summarized as L → L + γ → γ → γ + γ₂ + σ. Y microalloying has a significant influence on the solidification process. The addition of Y increases the nucleation temperature of austenite, raises nucleation density, and refines the solidification microstructure. However, Y addition also leads to an increased amount of eutectoid structures. This is primarily because Y broadens the solidification temperature range of the alloy and prolongs grain growth perio, which aggravates the microsegregation of elements such as Cr and Mo. Moreover, Y raises the initial precipitation temperature of the σ phase and enhances atomic diffusion during solidification, further promoting σ phase precipitation during the subsequent eutectoid transformation. Full article

This study investigates the microstructural evolution and mechanical properties of high-nickel shipbuilding steel during thermal processing using high-temperature confocal laser-scanning microscopy (HTCLSM). An in situ observation of the heating and holding processes reveals critical insights into phase transformations, grain-growth behavior, and the formation of precipitates. The experimental results demonstrate that austenitization begins at approximately 700 °C, with significant grain-boundary nucleation. At 900 °C, the formation of black precipitates was observed, and their persistence up to temperatures exceeding 1000 °C was confirmed. Scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) analyses identified these precipitates as chromium carbides (Cr₇C₃), which significantly contribute to the material’s strength. A comprehensive analysis using transmission electron microscopy (TEM) confirmed the presence and distribution of Cr₇C₃ within the grains and along grain boundaries. These findings provide a deeper understanding of the microstructural dynamics in high-nickel steels, guiding the optimization of heat-treatment processes to enhance mechanical properties for maritime applications. Full article

The effects of Y on the solidification process of 7Mo super austenitic stainless steel (7MoSASS) under low cooling rate conditions (10 °C/min) were investigated using high-temperature confocal laser scanning microscopy (HT-CLSM). The in situ observation results indicate that Y samples promote an increase in austenite nucleation density. After 10 s of nucleation, the nucleation density increased by 149.53/mm² for the Y sample. Furthermore, variance analysis indicated that Y addition improved the uniformity of the 7MoSASS solidification microstructure under low cooling rate conditions. The Johnson–Mehl–Avrami–Kolmogorov (JMAK) theory results showed that when the solid phase ratio was 0.5, the nucleation mode of the Y sample transitioned from saturation site nucleation to saturation site nucleation + Avrami nucleation. YAlO₃ has a low lattice disregistry value with austenite, making it a suitable heterogeneous nucleation core for promoting the early nucleation of austenite. During the late stages of solidification, Y accumulates in the residual liquid phase, providing a greater degree of compositional undercooling. SEM-EDS analysis showed that Y contributed to the refinement of the 7MoSASS solidification microstructure, with the proportion of precipitated phases decreasing by approximately 7.5%. Cr and Mo were the main elements exhibiting positive segregation in 7MoSASS, and the Cr segregation ratio increased in the Y sample, while the Mo segregation ratio decreased. Full article

Hyper duplex stainless steel (HDSS) is a new alloy group of duplex stainless steels with the excellent corrosion resistance and mechanical properties among the existing modern stainless steels. Due to the incorporation of the high content of alloying elements, e.g., Cr, Ni, Mo, etc., the crystallization behavior of δ-ferrite from liquid is of vital importance to be controlled. In this work, the effect of the cooling rate (i.e., 4 °C/min and 150 °C/min) on the nucleation and growth behavior of δ-ferrite in S33207 during the solidification was investigated using a high-temperature confocal scanning laser microscope (HT-CLSM) in combination with electron microscopies and thermodynamic calculations. The obtained results showed that the solidification mode of S33207 steel was a ferrite–austenite type (FA mode). L→δ-ferrite transformation occurred at a certain degree of undercooling, and merging occurred during the growth of the δ-ferrite phase dendrites. Similar microstructure characteristics were observed after solidification under two different cooling rates. The variation in the area fraction of δ-ferrite with different temperatures and time intervals during the solidification of S33207 steels was calculated at different cooling rates. The post-microstructure as well as its composition evolution were also briefly investigated. This work shed light on the real-time insights for the crystallization behavior of hyper duplex stainless steels during their solidification process. Full article

Non-metallic inclusions (NMIs) in steels have been the focus of various experimental studies due to their detrimental character. While isolated processes, such as agglomeration or dissolution, have been well investigated, holistic in-situ views with high-temperature confocal scanning laser microscopy (HT-CSLM) have been rare. In this work a novel and suitable method is presented to simultaneously observe agglomeration, movement, detachment, and dissolution of non-metallic inclusions by combined the melting of steel and slag with a dual-crucible approach. Therefore, different steel/slag combinations were tested. It is shown that, with transparent that does not become tarnished by the ions stemming from the steel, the steel’s surface and non-metallic inclusions are observable. Furthermore, technological limitations are discussed, including restrictions regarding the melting point of steels and certain steel/slag combinations. Full article

Crystallization during the solidification process of steels is of vital importance for controlling the quality of final products. This paper summarizes the in situ characterization research activities of crystallization behaviors of low-alloy steels during the solidification process. The results obtained using high-temperature confocal laser scanning microscope (HT-CLSM) are critically reviewed, and other relevant methodologies, i.e., either classical method using differential scanning calorimetry (DSC) or large-scale facility (LSF), are also briefly mentioned. The evolution of the crystallization front from a planar to a cellular and further to a dendritic one, and subsequential microstructure evolutions, i.e., delta-ferrite (δ) formation from the liquid, austenite (γ) transformation and decomposition, are mainly discussed. The current review aims to highlight the state-of-the-art research outputs obtained by the novel in situ characterization techniques, and the obtained knowledge aims to shed light on the further development of the quality low-alloy steel products by controlling the processing and structure correlation. Full article

In this study, an Fe–Cr–Mo–Ni–B coating was prepared using plasma cladding on Cr5 steel substrate. The microstructure, phase evolution and tribological performance of the Fe–Cr–Mo–Ni–B coating were investigated. The microstructure is mainly composed of Mo₂FeB₂, Fe₂B, α-Fe, γ-Fe and MoB. The process of phase evolution in the coating was observed in situ by HT-CLSM. The Mo₂FeB₂ phase with good thermodynamic stability can exist in the high-temperature liquid phase. It also has a phenomenon of connection and merging and turns into different morphology during the plasma cladding process. The hardness value of coating was much higher than the base metal, and the hardness value of Mo₂FeB₂ (785.5 HV) was higher than the eutectic matrix (693.2 HV). The wear mechanisms of the cladding under dry sliding were primarily caused by adhesive wear, accompanying slight oxidation wear. The Mo₂FeB₂ phase has an important effect on the wear resistance property. Full article

The study is dedicated to the investigation of serotonin (5-hydroxytryptamine, 5-HT) and 5-HT₇ type serotonin receptor of localisation in larvae of two parasitic flatworms Opisthorchis felineus (Rivolta, 1884) Blanchard, 1895 and Hymenolepis diminuta Rudolphi, 1819, performed using the immunocytochemical method and confocal laser scanning microscopy (CLSM). Using whole mount preparations and specific antibodies, a microscopic analysis of the spatial distribution of 5-HT₇-immunoreactivity(-IR) was revealed in worm tissue. In metacercariae of O. felineus 5-HT₇-IR was observed in the main nerve cords and in the head commissure connecting the head ganglia. The presence of 5-HT₇-IR was also found in several structures located on the oral sucker. 5-HT₇-IR was evident in the round glandular cells scattered throughout the larva body. In cysticercoids of H. diminuta immunostaining to 5-HT₇ was found in flame cells of the excretory system. Weak staining to 5-HT₇ was observed along the longitudinal and transverse muscle fibres comprising the body wall and musculature of suckers, in thin longitudinal nerve cords and a connective commissure of the central nervous system. Available publications on serotonin action in flatworms and serotonin receptors identification were reviewed. Own results and the published data indicate that the muscular structures of flatworms are deeply supplied by 5-HT₇-IR elements. It suggests that the 5-HT₇ type receptor can mediate the serotonin action in the investigated species and is an important component of the flatworm motor control system. The study of the neurochemical basis of parasitic flatworms can play an important role in the solution of fundamental problems in early development of the nervous system and the evolution of neuronal signalling components. Full article

Nanocarrier-based delivery systems are promising strategies for enhanced therapeutic efficacy and safety of toxic drugs. Photodynamic therapy (PDT)—a light-triggered chemical reaction that generates localized tissue damage for disease treatments—usually has side effects, and thus patients receiving photosensitizers should be kept away from direct light to avoid skin phototoxicity. In this study, a clinically therapeutic antibody cetuximab (C225) was conjugated to the surface of methoxy poly(ethylene glycol)-b-poly(lactide) (mPEG-b-PLA) micelles via thiol-maleimide coupling to allow tumor-targetable chlorin e6 (Ce6) delivery. Our results demonstrate that more C225-conjugated Ce6-loaded polymeric micelles (C225-Ce6/PM) were selectively taken up than Ce6/PM or IgG conjugated Ce6/PM by epidermal growth factor receptor (EGFR)-overexpressing A431 cells observed by confocal laser scanning microscopy (CLSM), thereby decreasing the IC₅₀ value of Ce6-mediated PDT from 0.42 to 0.173 μM. No significant differences were observed in cellular uptake study or IC₅₀ value between C225-Ce6/PM and Ce6/PM groups in lower EGFR expression HT-29 cells. For antitumor study, the tumor volumes in the C225-Ce6/PM-PDT group (percentage of tumor growth inhibition, TGI% = 84.8) were significantly smaller than those in the Ce6-PDT (TGI% = 38.4) and Ce6/PM-PDT groups (TGI% = 53.3) (p < 0.05) at day 21 through reduced cell proliferation in A431 xenografted mice. These results indicated that active EGFR targeting of photosensitizer-loaded micelles provides a possible way to resolve the dose-limiting toxicity of conventional photosensitizers and represents a potential delivery system for PDT in a clinical setting. Full article

This paper is an attempt to elucidate the effects of the important spray characteristics on the surface morphology and light absorbance of spray-on P3HT:PCBM thin-films, used as an active layer in polymer solar cells (PSCs). Spray coating or deposition is a viable scalable technique for the large-scale, fast, and low-cost fabrication of solution-processed solar cells, and has been widely used for device fabrication, although the fundamental understanding of the underlying and controlling parameters, such as spray characteristics, droplet dynamics, and surface wettability, is still limited, making the results on device fabrication not reproducible and unreliable. In this paper, following the conventional PSC architecture, a PEDOT:PSS layer is first spin-coated on glass substrates, followed by the deposition of P3HT:PCBM using an automatic ultrasonic spray coating system, with a movable nozzle tip, to mimic an industrial manufacturing process. To gain insight, the effects of the spray carrier air pressure, the number of spray passes, the precursor flow rate, and precursor concentration are studied on the surface topography and light absorbance spectra of the spray-on films. Among the results, it is found that despite the high roughness of spray-on films, the light absorbance of the film is satisfactory. It is also found that the absorbance of spray-on films is a linear function of the number of spray passes or deposition layers, based on which an effective film thickness is defined for rough spray-on films. The effective thickness of a rough spray-on P3HT:PCBM film was found to be one-quarter of that of a flat film predicted by a simple mass balance. Full article

Discovering new fluorochromes is significantly advanced by high-throughput screening (HTS) methods. In the present study a combination of small molecule microarray (SMM) prescreening and confocal laser scanning microscopy (CLSM) was developed in order to discover novel cell staining fluorescent dyes. Compounds with high native fluorescence were selected from a 14,585-member library and further tested on living cells under the microscope. Eleven compartment-specific, cell-permeable (or plasma membrane-targeted) fluorochromes were identified. Their cytotoxicity was tested and found that between 1–10 micromolar range, they were non-toxic even during long-term incubations. Full article

In order to investigate the microbe-mineral interaction in the micro scale, spatial distribution and speciation of Cu and S in Halothiobacillus HT1 biofilm formed on a CuS surface was examined using synchrotron-based X-ray techniques. Confocal laser scanning microscope (CLSM) results indicated that Halothiobacillus HT1 biofilm formation gave rise to distinct chemical and redox gradients, leading to diverse niches in the biofilm. Live cells were distributed at the air-biofilm and membrane-biofilm interface. CuS was oxidized by Halothiobacillus HT1 biofilm, and copper penetrated into the biofilm. Sulfide was oxidized to cysteine (77.3%), sulfite (3.8%) and sulfonate (18.9%). Cu-cysteine-like species were involved in the copper homeostasis. These results significantly improve our understanding of the interfacial properties of the biofilm-mineral interface. Full article