Search Results (81)

The increasing impact of global warming is predominantly driven by the extensive use of fossil fuels, which release significant amounts of greenhouse gases into the atmosphere. This has led to a critical need for alternative, sustainable energy sources that can mitigate environmental impacts. Photovoltaic technology has emerged as a promising solution by harnessing renewable energy from the sun, providing a clean and inexhaustible power source. Perovskite solar cells (PSCs) are a class of hybrid organic–inorganic solar cells that have recently attracted significant scientific attention due to their low cost, relatively high efficiency, low–temperature processing routes, and longer carrier lifetimes. These characteristics make them a viable alternative to traditional fossil fuels, reducing the carbon footprint and contributing to the fight against global warming. In this study, the SCAPS–1D numerical simulator was used in the computational analysis of a PSC device with the configuration FTO/ETL/BaZr(S_0.6Se_0.4)₃/HTL/Ir. Different hole transport layer (HTL) and electron transport layer (ETL) material were proposed and tested. The HTL materials included copper (I) oxide (Cu₂O), 2,2′,7,7′–Tetrakis(N,N–di–p–methoxyphenylamine)9,9′–spirobifluorene (spiro–OMETAD), and poly(3–hexylthiophene) (P₃HT), while the ETLs included cadmium suphide (CdS), zinc oxide (ZnO), and [6,6]–phenyl–C₆₁–butyric acid methyl ester (PCBM). Finally, BaZr(S_0.6Se_0.4)₃ was proposed as an absorber, and a fluorine–doped tin oxide glass substrate (FTO) was proposed as an anode. The metal back contact used was iridium. Photovoltaic parameters such as short circuit density (I_sc), open circuit voltage (V_oc), fill factor (FF), and power conversion efficiency (PCE) were used to evaluate the performance of the device. The initial simulated primary device with the configuration FTO/CdS/BaZr(S_0.6Se_0.4)₃/spiro–OMETAD/Ir gave a PCE of 5.75%. Upon testing different HTL materials, the best HTL was found to be Cu₂O, and the PCE improved to 9.91%. Thereafter, different ETLs were also inserted and tested, and the best ETL was established to be ZnO, with a PCE of 10.10%. Ultimately an optimized device with a configuration of FTO/ZnO/BaZr(S_0.6Se_0.4)₃/Cu₂O/Ir was achieved. The other photovoltaic parameters for the optimized device were as follows: FF = 31.93%, J_sc = 14.51 mA cm⁻², and V_oc = 2.18 V. The results of this study will promote the use of environmentally benign BaZr(S_0.6Se_0.4)₃–based absorber materials in PSCs for improved performance and commercialization. Full article

In this study, 74 bacterial isolates were obtained from sediments of Šibenik Bay, which has historically been impacted by heavy metal pollution. Isolates were tested for tolerance to cadmium (Cd), cobalt (Co), chromium (Cr), copper (Cu), mercury (Hg), nickel (Ni), lead (Pb), tin (Sn), and zinc (Zn), both individually and in mixtures, and for their biofilm-forming ability. Toxicity followed the trend Hg > Sn > Zn/Cd/Cr > Co/Ni > Pb, with Cu showing resistance across different concentrations. Resistance traits were observed against all tested metals, with some isolates displaying multi-metal resistance to as many as seven metals, reflecting long-term selective pressure in the Bay. The Bacillus species dominated the community (48 isolates across five clusters), confirming this genus as the principal group in metal-polluted sediments. Several less-explored genera, including Ruegeria/Cribrihabitans, Bhargavaea, Pseudoalteromonas, and Lysinibacillus/Sporosarcina, also exhibited notable resistance traits, underscoring their potential as novel candidates for bioremediation. Eleven isolates from Bacillus/Mesobacillus/Cytobacillus, Bacillus/Peribacillus/Rossellomorea, Bacillus/Pseudoalkalibacillus/Alkalibacillus, Lysinibacillus/Sporosarcina, and Ruegeria/Cribrihabitans clusters showed resistance and robust growth under metal mixtures. Among all isolates, 11, 32, 81, and 82 (Bacillus/Mesobacillus/Cytobacillus and Bacillus/Peribacillus/Rossellomorea) combined broad multi-metal tolerance with strong biofilm formation, positioning them as candidates for site-specific, nature-based bioremediation of heavy-metal-impacted coastal ecosystems such as Šibenik Bay. Full article

CdS nanowires have garnered considerable attention lately for their promising potential in next-generation nanolaser devices, attributed to their relatively high stability and exceptional emission efficiency within the Ⅱ–Ⅵ semiconductor family. In this study, tin-doped CdS nanowires with varying dimensions were synthesized, and the underlying mechanisms responsible for the formation of micro-cavities within these nanowires were systematically explored through scanning electron microscopy (SEM) analysis and photoluminescence mapping. The results show that a very distinct hexagonal-shaped micro-cavity is observed on the cross-section of CdS nanowires, and the size of the micro-cavity is determined by the radius of the nanowire. Additionally, through the use of angle-resolved micro-fluorescence Fourier imaging technology, it is found that under high excitation density conditions, the micro-cavity mode is more prominent at higher collection angles, which is consistent with the mode of the wall-pass cavity micro-cavity. Finally, the formation of the full reflection spectrum of the micro-cavity mode is confirmed through the wavelength shift and intensity shift phenomena related to the excitation power. These results further deepen our understanding of the micro-cavity modes in tin-doped cadmium sulfide nanowires, which may be of great significance for the application of these nanowires in new optical devices. Full article

This study investigates the development and sensing profile of synthetic melanin nanoparticle-coated electrodes for the electrochemical detection of heavy metals, including lead (Pb), cadmium (Cd), cobalt (Co), zinc (Zn), nickel (Ni), and iron (Fe). Synthetic melanin films were prepared in situ by the deacetylation of diacetoxy indole (DAI) to dihydroxy indole (DHI), followed by the deposition of DHI monomers onto indium tin oxide (ITO) and glassy carbon electrodes (GCE) using cyclic voltammetry (CV), forming a thin layer of synthetic melanin film. The deposition process was characterized by electrochemical quartz crystal microbalance (EQCM) in combination with linear sweep voltammetry (LSV) and amperometry to determine the mass and thickness of the deposited film. Surface morphology and elemental composition were examined using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). In contrast, Fourier-transform infrared (FTIR) and UV–Vis spectroscopy confirmed the melanin’s chemical structure and its polyphenolic functional groups. Differential pulse voltammetry (DPV) and amperometry were employed to evaluate the melanin films’ electrochemical activity and sensitivity for detecting heavy metal ions. Reproducibility and repeatability were rigorously assessed, showing consistent electrochemical performance across multiple electrodes and trials. A comparative analysis of ITO, GCE, and graphite electrodes was conducted to identify the most suitable substrate for melanin film preparation, focusing on stability, electrochemical response, and metal ion sensing efficiency. Finally, the applicability of melanin-coated electrodes was tested on in-house heavy metal water samples, exploring their potential for practical environmental monitoring of toxic heavy metals. The findings highlight synthetic melanin-coated electrodes as a promising platform for sensitive and reliable detection of iron with a sensitivity of 106 nA/ppm and a limit of quantification as low as 1 ppm. Full article

Se-doped CdTe thin films were grown employing a simple two-electrode electrochemical deposition method using glass/tin-doped indium oxide (glass/ITO). Cadmium acetate dihydrate [Cd (CH₃CO₂)₂. 2H₂O], selenium dioxide (SeO₂), and tellurium dioxide (TeO₂) were used as precursors. Instruments including X-ray diffraction for structural investigation, UV-Vis spectrophotometry for optical properties, and scanning probe microscopy for morphological properties were employed to investigate the physico-chemical characteristics of the resulting Se-doped CdTe thin-film. The films are polycrystalline with a cubic phase, according to X-ray diffraction (XRD) data. More ions are deposited on the substrate, which makes the material more crystalline and intensifies the characteristic peaks that are seen. It is observed from the acquired optical characterization that the film’s bandgap is greatly influenced by the deposition time. The bandgap dropped from 1.92 to 1.62 as the deposition period increased from 25 to 45 min, making the film more transparent and absorbing less light at shorter deposition durations. Images from scanning electron microscopy (SEM) show that the surface morphology is homogenous with closely packed grains and that the grain forms become less noticeable as the deposition time increases. This work is novel in that it investigates the influence of the deposition time on the structural, optical, and morphological properties of Se-doped CdTe thin films deposited using a cost-effective, simplified two-electrode electrochemical method—a fabrication route that remains largely unexplored for this material system. Full article

Animal-based food is significant for human nutrition, as it represents an easily digestible source of high-quality proteins, fatty acids, fat-soluble vitamins, and energy. During evolution, humans developed anatomical, metabolic, and biochemical adaptations in the digestive tract, becoming increasingly dependent on nutritionally valuable food, such as animal-based products. Animal-based food can be a source of chemical substances that are harmful to health, such as contaminants (heavy metals, mycotoxins, organochlorine pesticides, etc.), veterinary drug residues, and additives. The subject of this paper is the determination of the content of essential (copper—Cu, iron—Fe, and chromium—Cr) and heavy and toxic metals (lead—Pb, cadmium—Cd, arsenic—As, and tin—Sn), as well as nitrites, in meat products, particularly pâtés and meat spreads available on the market in the Republic of Srpska. Determination of the content of metals was performed using the ICP-OES method, while nitrites were analyzed using the standard SRPS ISO 2918/1999 method. The obtained results indicate that the content of heavy and toxic metals and nitrites is lower than the maximum prescribed by national regulations, namely the Rulebook on Maximum Amounts of Certain Contaminants (Official Gazette of BA, No. 68/14, 79/16, 84/18) and the Rulebook on Additives in Food (Official Gazette of BA, No. 33/18 and 6/21). Full article

Osteoporosis is a major public health concern, particularly among postmenopausal women. Environmental exposure to metals has been proposed as a potential contributor to osteoporosis, but human data remain limited and inconsistent. This study investigated changes in urinary concentrations of 20 metal(loid)s in patients with osteoporosis, as well as the association of these elements with bone mineral density (BMD), in a cohort of 380 postmenopausal women aged 50–70 years from Cascavel, Paraná, Brazil. Demographic, lifestyle, and clinical data were collected, and urinary concentrations of aluminum (Al), barium (Ba), cadmium (Cd), cobalt (Co), cesium (Cs), copper (Cu), mercury (Hg), lithium (Li), manganese (Mn), molybdenum (Mo), nickel (Ni), lead (Pb), rubidium (Rb), antimony (Sb), selenium (Se), tin (Sn), strontium (Sr), thallium (Tl), uranium (U), and zinc (Zn) were measured by inductively coupled plasma mass spectrometry. BMD was assessed at the lumbar spine, femoral neck, and total hip using dual-energy X-ray absorptiometry. Osteoporosis was diagnosed in 73 participants (19.2%). Osteoporotic women had significantly higher urinary concentrations of Cd, Mn, Pb, Sb, Sn, and Zn (p < 0.05). Statistically significant negative correlations were observed between BMD and urinary concentrations of Al, Cd, Hg, Mn, Sb, and U. After adjustment for confounders, elevated urinary concentrations of Cd, Mn, Pb, and Sb remained independently and significantly associated with higher odds of osteoporosis, with Cd (aOR = 1.495; p = 0.026) and Sb (aOR = 2.059; p = 0.030) showing the strongest associations. In addition, women with urinary concentrations above the 90th percentile for both Cd and Sb had a significantly higher prevalence of osteoporosis compared to those with lower levels (44.4% vs. 18.0%; p = 0.011). Longitudinal studies are needed to confirm causality and inform prevention strategies. Full article

Copper zinc tin sulfide (commonly known as CZTS) solar cells (SCs) are gaining attention as a promising technology for sustainable electricity generation owing to their cost-effectiveness, availability of materials, and environmental advantages. The goal of this study is to enhance CZTS SC performance by adding a back surface field (BSF) layer. SC capacitance simulator software (SCAPS) was used to examine three different configurations. Another option is to replace the cadmium sulfide (CdS) buffer layer with a titanium dioxide (TiO₂) layer. The results demonstrate that the reduced graphene oxide (rGO) BSF layer increases the conversion efficiency by 25.68% and significantly improves the fill factor, attributed to lowering carrier recombination and creating a quasi-ohmic contact at the interface between the metal and semiconductor. Furthermore, replacing the CdS buffer layer with TiO₂ offers potential efficiency gains and mitigates environmental concerns associated with the toxicity of CdS. The results of this investigation could enhance the efficiency and viability of CZTS SCs for future energy applications. However, it is observed that BSF layers may become less effective at elevated temperatures due to increased recombination, leading to reduced carrier lifetime. This study underlines valuable insights into optimizing CZTS SC performance through advanced material choices, highlighting the dual benefits of improved efficiency and reduced environmental impact. Full article

This study investigates the structural, optical, and photocatalytic properties of cadmium oxide (CdO) nanoparticles (NPs) and indium–tin oxide (ITO)-doped CdO NPs. The synthesis of CdO NPs and ITO NPs was accomplished through the co-precipitation method. Scanning electron microscopy (SEM) analysis indicates that pure CdO NPs exhibit agglomerated structures, whereas ITO doping introduces porosity and roughness, thereby improving particle dispersion and facilitating electron transport. Energy dispersive spectroscopy (EDS) corroborates the successful incorporation of tin (Sn) and indium (In) within indium–tin oxide (ITO)-doped cadmium oxide (CdO) nanoparticles (NPs) in addition to cadmium (Cd) and oxygen (O). X-ray diffraction (XRD) analysis demonstrates that an increase in ITO doping results in a reduction of the crystallite size, decreasing from 23.43 nm for pure CdO to 18.42 nm at a 10% doping concentration, which can be attributed to lattice distortion. Simultaneously, the band gap exhibits a narrowing from 2.92 eV to 2.52 eV, achieving an optimal value at 10% ITO doping before experiencing a slight increase at higher doping concentrations. This tuneable band gap improves light absorption, which is crucial for photocatalysis. The photocatalytic degradation of rhodamine B (RhB) highlights the superior efficiency of ITO-doped CdO nanoparticles, achieving a remarkable 94.68% degradation under sunlight within 120 min, up 81.01%, significantly surpassing the performance of pure CdO. The optimal RhB concentration for achieving maximum degradation was determined to be 5 mg/L. This enhanced catalytic activity demonstrates the effectiveness of ITO-doped CdO NPs under both UV and visible light, showcasing their potential for efficient pollutant degradation in sunlight-driven applications. Full article

Cadmium-tin-oxide (CTO), also referred to as cadmium stannate (Cd₂SnO₄), is known for its interesting electrical, electronic, and optical properties, making it useful in various applications such as in transparent conducting oxides for optoelectronic devices and also in photovoltaic applications. While its properties have been investigated experimentally, there is not much record in the literature on the computational study of the electronic and optical properties of CTO. This study employed density functional theory to explore the two properties of CTO. The hybrid functionals were used to widen the band gap from 0.381 eV (for PBE) to 3.13 eV, which replicates the experimental values very well. The other properties obtained were a refractive index of 2.53, absorption coefficient of 1.43 × 10⁴ cm⁻¹, and dielectric constant of 6.401 eV. The optical energy loss of 0.00691 that was investigated for the first time in this work adds to the literature on the properties of CTO. However, the electrical properties of CTO, which also play a key role in the working of optoelectronic devices, need to be investigated. Full article

In the dynamic field of photovoltaic technology, the pursuit of efficiency and sustainability has led to continuous novelty, shaping the landscape of solar energy solutions. One of the key elements affecting the efficiency of photovoltaic cells of II^nd and III^rd generation is the presence of transparent conductive oxide (TCO) layers, which are key elements impacting the efficiency and durability of solar panels, especially for DSSC, CdTe, CIGS (copper indium gallium diselenide) or organic, perovskite and quantum dots. TCO with low electrical resistance, high mobility, and high transmittance in the VIS–NIR region is particularly important in DSSC, CIGS, and CdTe solar cells, working as a window and electron transporting layer. This layer must form an ohmic contact with the adjacent layers, typically the buffer layer (such as CdS or ZnS), to ensure efficient charge collection Furthermore it ensures protection against oxidation and moisture, which is especially important when transporting the active cell structure to further process steps such as lamination, which ensures the final seal. Transparent conductive oxide layers, which typically consist of materials such as indium tin oxide (ITO) or alternatives such as fluorine-doped tin oxide (FTO), serve dual purposes in photovoltaic applications. Primarily located as the topmost layer of solar cells, TCOs play a key role in transmitting sunlight while facilitating the efficient collection and transport of generated electrical charges. This complex balance between transparency and conductivity highlights the strategic importance of TCO layers in maximizing the performance and durability of photovoltaic systems. As the global demand for clean energy increases and the photovoltaic industry rapidly develops, understanding the differential contribution of TCO layers becomes particularly important in the context of using PV modules as building-integrated elements (BIPV). The use of transparent or semi-transparent modules allows the use of building glazing, including windows and skylights. In addition, considering the dominant position of the Asian market in the production of cells and modules based on silicon, the European market is intensifying work aimed at finding a competitive PV technology. In this context, thin-film, organic modules may prove competitive. For this purpose, in this work, we focused on the electrical parameters of two different thicknesses of a transparent FTO layer. First, the influence of the FTO layer thickness on the transmittance over a wide range was verified. Next, the chemical composition was determined, and key electrical parameters, including carrier mobility, resistivity, and the Hall coefficient, were determined. Full article

Valley surface water is considered a focal public health concern owing to the presence of multi-drug-resistant bacteria. The distribution of antimicrobial resistance (AMR) bacteria in the surface water is affected by the presence of multiple factors, including antibiotics coming from wastewater discharge or other contaminant sources such as pharmaceuticals, biocides, and heavy metals. Furthermore, there is evidence suggesting that high levels of antibiotic resistance genes (ARGs) can be transferred within bacterial communities under the influence of heavy metal stress. Hence, the primary aim of this study is to investigate the presence of heavy metals and bacterial ARGs in upstream as well as downstream locations of Wadi Hanifah Valley in Riyadh, Saudi Arabia. Sample collection was conducted at eighteen surface water sites within the valley in total. The selection of ARGs was associated with the most common antibiotics, including β-lactam, tetracycline, erythromycin, gentamicin, sulphonamide, chloramphenicol, vancomycin, trimethoprim, and colistin antibiotics, which were detected qualitatively using polymerase chain reaction (PCR) technology. The tested antibiotic resistance genes (ARGs) included (bla_NDM-1 (for the antibiotic class Beta-lactamases), mecA (methicillin-resistant Staphylococcus aureus), tet(M) and tet(B) (for the antibiotic class Tetracycline), ampC (for the antibiotic class Beta-lactamases), vanA (for the antibiotic class vancomycin), mcr-1 (for the antibiotic class colistin), erm(B) (for the antibiotic class erythromycin), aac6′-Ie-aph2-Ia (for the antibiotic class Gentamicin), sulII (for the antibiotic class sulphonamide), catII (for the antibiotic class Chlorophincol), and dfrA1 (for the antibiotic class trimethoprim). Moreover, an assessment of the levels of heavy metals such as lithium (Li), beryllium (Be), chromium (Cr), cobalt (Co), arsenic (As), cadmium (Cd), tin (Sn), mercury (Hg), and lead (Pb) was conducted by using inductively coupled plasma mass spectrometry (ICPMS). According to our findings, the concentrations of sulphonamide, erythromycin, and chloramphenicol ARGs (erm(B), sulII, and catII) were observed to be the most elevated. Conversely, two ARGs, namely mecA and mcr-1, were not detected in the samples. Moreover, our data illustrated a significant rise in ARGs in the bacteria of water samples from the upstream sites as compared with the water samples from the downstream sites of Wadi Hanifah Valley. The mean concentration of Li, Be, Cr, Co, As, Cd, Sn, Hg, and Pb in the water samples was estimated to be 37.25 µg/L, 0.02 µg/L, 0.56 µg/L,0.32 µg/L, 0.93 µg/L, 0.01 µg/L, 200.4 µg/L, 0.027 µg/L, and 0.26 µg/L, respectively, for the selected 18 sites. Furthermore, it was revealed that the concentrations of the screened heavy metals in the water samples collected from various sites did not surpass the maximum limits set by the World Health Organization (WHO). In conclusion, this study offers a concise overview of the presence of heavy metals and ARGs in water samples obtained from the Wadi Hanifah Valley in Riyadh, KSA. Such findings will contribute to the ongoing monitoring and future risk assessment of ARGs spread in surface water. Full article

The impact of N₂ purging in the CdS deposition bath and subsequent N₂ annealing is examined and contrasted with conventional CdS films, which were deposited without purging and annealed in ambient air. All films were fabricated using the chemical bath deposition method at a temperature of 80 °C on fluorine-doped tin oxide glass slides (FTO). N₂ purged films were deposited by introducing nitrogen gas into the deposition bath throughout the CdS deposition process. Subsequently, both N₂ purged and un-purged films underwent annealing at temperatures ranging from 100 to 500 °C for one hour, either in a nitrogen or ambient air environment. Photoelectrochemical (PEC) cell studies reveal that films subjected to both N₂ purging and N₂ annealing exhibit a notable enhancement of 37.5% and 27% in I_SC (short-circuit current) and V_OC (open-circuit voltage) values, accompanied by a 5% improvement in optical transmittance compared to conventional CdS thin films. The films annealed at 300 °C demonstrate the highest I_SC, V_OC, and V_FB values, 55 μA, 0.475 V, and −675 mV, respectively. The improved optoelectrical properties in both N₂-purged and N₂-annealed films are attributed to their well-packed structure, enhanced interconnectivity, and a higher sulfur to cadmium ratio of 0.76 in the films. Full article

In this work, we report a new concept of upconversion-powered photoelectrochemical (PEC) bioanalysis. The proof-of-concept involves a PEC bionanosystem comprising a NaYF₄:Yb,Tm@NaYF₄ upconversion nanoparticles (UCNPs) reporter, which is confined by DNA hybridization on a CdS quantum dots (QDs)/indium tin oxide (ITO) photoelectrode. The CdS QD-modified ITO electrode was powered by upconversion absorption together with energy transfer effect through UCNPs for a stable photocurrent generation. By measuring the photocurrent change, the target DNA could be detected in a specific and sensitive way with a wide linear range from 10 pM to 1 μM and a low detection limit of 0.1 pM. This work exploited the use of UCNPs as signal reporters and realized upconversion-powered PEC bioanalysis. Given the diversity of UCNPs, we believe it will offer a new perspective for the development of advanced upconversion-powered PEC bioanalysis. Full article

Flexible organic light-emitting diodes (FOLEDs) have promising potential for future wearable applications because of their exceptional mechanical flexibility. Silver nanowire (Ag NW) networks are the most promising candidates to replace indium tin oxide (ITO), which is limited by its poor bendability. In this study, three different methods including methanol impregnation, argon plasma treatment, and ultraviolet radiation were used to reduce the junction resistance of Ag NWs to optimize the flexible transparent electrodes (FTEs); which were prepared using Ag NWs and poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT: PSS). Then, the optoelectronic properties of the FTEs were further improved by using a co-doped system of silver nanowires and silver nanoparticles (Ag NPs), the structure of which consisted of PET/Ag NWs: Ag NPs/PEDOT: PSS/DMSO. The largest FOM value of 1.42 × 10⁻² ohm⁻¹ and a low sheet resistance value of 13.86 ohm/sq were obtained using the optimized FTEs. The prepared FOLED based on the optimized FTEs had a luminous efficiency of 6.04 cd/A and a maximum EQE of 1.92%, and exhibited no observed decline in efficiency when reaching maximum luminance. After 500 bending tests, the luminance still reached 82% of the original value. It is demonstrated that the FTEs prepared via the co-doped system have excellent optoelectronic properties as well as high mechanical stability. Full article