Next Article in Journal
Deformation Characteristics of the Shear Zone and Movement of Block Stones in Soil–Rock Mixtures Based on Large-Sized Shear Test
Previous Article in Journal
Dental Condition as A Factor Modifying the Transmission of the Sound Vibration in the Skull Bones
Previous Article in Special Issue
Renewable Energy and Sustainability from the Supply Side: A Critical Review and Analysis
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Sugarcane Industry Waste Recovery: A Case Study Using Thermochemical Conversion Technologies to Increase Sustainability

by
Leonel J. R. Nunes
1,2,*,
Liliana M. E. F. Loureiro
3,
Letícia C. R. Sá
3 and
Hugo F. C. Silva
4
1
PROMETHEUS–Unidade de Investigação em Materiais, Energia e Ambiente para a Sustentabilidade, Escola Superior Agrária, Instituto Politécnico de Viana do Castelo, Rua da Escola Industrial e Comercial de Nun’Alvares, 4900-347 Viana do Castelo, Portugal
2
GOVCOPP–Unidade de Investigação em Governança, Competitividade e Políticas Públicas, DEGEIT—Departamento de Economia, Gestão, Engenharia Industrial e Turismo, Universidade de Aveiro, Campus Universitário de Santiago, 3810-193 Aveiro, Portugal
3
YGE–Yser Green Energy SA, Área de Acolhimento Empresarial de Úl/Loureiro, Lote 17, 3720-075 Loureiro OAZ, Portugal
4
AFS–Advanced Fuel Solutions SA, Área de Acolhimento Empresarial de Úl/Loureiro, Lote 17, 3720-075 Loureiro OAZ, Portugal
*
Author to whom correspondence should be addressed.
Appl. Sci. 2020, 10(18), 6481; https://doi.org/10.3390/app10186481
Submission received: 7 August 2020 / Revised: 2 September 2020 / Accepted: 16 September 2020 / Published: 17 September 2020
(This article belongs to the Special Issue Biomass Energy and Biomass as a Clean Renewable Fuel)

Abstract

:
The sugarcane industry has assumed an increasingly important role at a global level, with countries such as Brazil and India dominating the field. However, this causes environmental problems, since the industry produces large amounts of waste, such as sugarcane bagasse. This by-product, which is energetically partially recovered in sugar mills and in the pulp and paper industry, can make a significant contribution to the general use of biomass energy, if the usual disadvantages associated with products with low density and a high moisture content are overcome. From this perspective, thermochemical conversion technologies, especially torrefaction, are assumed to be capable of improving the fuel properties of this material, making it more appealing for potential export and use in far-off destinations. In this work, sugarcane samples were acquired, and the process of obtaining bagasse was simulated. Subsequently, the bagasse was dried and heat-treated at 200 and 300 °C to simulate the over-drying and torrefaction process. Afterward, product characterization was performed, including thermogravimetric analysis, elemental analysis, calorimetry, and energy densification. The results showed significant improvements in the energy content, from 18.17 to 33.36 MJ·kg−1 from dried bagasse to torrefied bagasse at 300 °C, showing that despite high mass loss, there is potential for a future value added chain for this waste form, since the increment in energy density could enhance its transportation and use in locations far off the production site.

1. Introduction

Sugarcane belongs to a restrict group of agricultural crops considered dominant, which, together with cotton, soy, corn, wheat, and rice, occupies millions of hectares of land [1,2,3]. In addition to countries where the species originates, the main producers are Southeast Asian countries, particularly the Philippines, Thailand, India, and Brazil, which have assumed global dominance concerning the area dedicated to production and yield per hectare achieved [4,5,6]. In fact, according to the information provided in 2020 by the United Nations Food and Agriculture Organization (FAO), there is currently an annual production of 1.89 billion tons, occupying a production area of 27,000,000 hectares spread over more than 100 countries. As can be seen in Table 1, the 20 largest world producers represent a production of 1.75 billion tons per year in an area of approximately 24,250,000 hectares, completely dominating the sector with 93% of world production in 91% of the total area occupied by sugarcane. In addition to being a food crop, sugarcane can also be considered an energy crop, since ethanol is produced from sugar. In this regard, Brazil is considered as a pioneer, mainly due to the developments achieved from the 1970s after the oil crisis [7,8,9,10].
The reality of sugarcane production in European countries is different from that in major production countries such as Brazil, India, the United States, and the Caribbean region [13,14,15,16]. In reality, production in Portugal, Spain, and Italy occurs in isolated regions, namely, in the island regions of Madeira, the Canaries, and Sicily, where sugarcane production was introduced as a subsistence culture to support colonization efforts centuries ago [17,18,19].
In Portugal, according to the official website of the Institute of Wine, Embroidery, and Handicrafts of Madeira (http://ivbam.gov-madeira.pt/cana-de-acucar-1316.aspx), sugarcane was introduced in 1425, imported from Sicily by order of D. Henrique shortly after the beginning of its colonization. The adaptability of this crop in terms of survival compared to others made it a vector for the creation of wealth [20,21,22,23]. In 1882, sugarcane was attacked by pests and almost disappeared completely in 1884, 1885, and 1886. The introduction of new varieties made it possible to rebuild the cane fields that, from 1890 onwards, expanded again, feeding the sugar industry and the manufacture of rum and alcohol on the island [24]. For farmers, sugarcane also had the advantage of having a remarkable double aptitude: it can also be used as fodder, as its leaves are rich in nutrients for animal feed [25]. This occurred at a time when the dairy industry was growing in Madeira [26]. At the end of the 1930s, sugarcane, which occupied an area of 6500 hectares, was reduced due to the delimitation of agrarian areas to an estimated total area of 1420 hectares in 1952 [27]. The average production in 1952 was considered to be limited to 30 tons per hectare. From 1952 onwards, the areas expanded a little more, and in 1955–1956, there was an appreciable increase in plantation. Until the end of the 1980s, there was a substantial decrease in the cultivation area related to the closure of several industrial units of great importance [20]. This has led to a collapse in the crop due to the lack of outlets, with the crop limited to just over 100 hectares (in 1986, it was 119.9 hectares, and it rapidly decreased to 90.3 hectares in 1988). In addition, farmers began to have other crops, such as bananas, vegetables, tropical and subtropical fruit trees, and vines, among others [26]. Currently, the area is around 172 hectares, which corresponds to a production of 10,830 tons. Productivity still varies, ranging from 40 t/ha in old cane fields to 120 t/ha in more recently installed cane fields. In terms of area, the most important municipalities are Ponta do Sol and Machico (with relative importance levels of 29 and 28%, respectively), followed by Santana (14%) and Calheta (8%), totaling 79% of the area of influence [28,29].
From this agricultural production, in addition to the main material, sugar, there are some by-products that are of interest for recovery. Of these, sugarcane bagasse stands out as a product with strong potential for energy recovery, since it is a renewable biological material that, if properly processed and densified, can be used an alternative source of carbon-neutral renewable energy [30,31,32]. Sugarcane bagasse is commonly used for the generation of steam in sugar plants and in the distillation of alcohol. In Brazil during the 1970s, Pro-Alcohol was the first major program to replace fossil fuel with a renewable fuel, hydrated ethanol [33,34,35]. At that time, bagasse was considered waste, and similar to any waste, it was necessary to discard it [36]. Burning or incineration in a boiler was a means to dispose this waste, generating part of the energy consumed at production plants [37]. Thus, over the years, bagasse has gone from a waste product to a relevant source of energy, and with each passing day, its importance increases proportionally to the evolution of energy prices in the international market [38]. Thus, this by-product is no longer considered a waste product and has become an important type of energy input [39]. Sugarcane bagasse presents great potential for the production of derived fuels using gasification, rapid pyrolysis, or hydrolysis followed by fermentation [40]. For further development of these technologies, detailed knowledge of the physical and chemical characteristics of sugarcane bagasse is necessary [41].
Sugarcane bagasse is also used in the pulp and paper industry, as documented in several studies, such as those presented by Samariha and Khakifirooz (2011) investigating the production of pulp from bagasse for the manufacture of corrugated board [42], the work of Lois-Correa (2012) studying the correlation between bagasse fiber quality and its influence on the final quality of the paper produced [43], and the research conducted by Hemmasi et al. (2011) analyzing the chemical and anatomical properties of sugarcane bagasse used in paper production [44]. However, as described in the referred works, it can be concluded that sugarcane bagasse presents a set of limitations—for example, its low bulk density and high moisture content, and the speed with which it starts its biological degradation process, similar to those identified in cereal straw, although it offers greater versatility [45].
This work aims to characterize the use of sugarcane bagasse for energy generation in a way that allows both its storage and the possibility of exporting it as an energy product due to the energy densification process using a thermochemical conversion process. To carry out this work, a bibliographical review of the processing of sugarcane bagasse was prepared when the sugarcane samples were acquired, which were characterized and subjected to the thermochemical conversion process of torrefaction as a way to achieve preservation for long periods of time, allowing safer storage without biological activity and becoming hydrophobic. These new thermally treated and energy densified products can be transported, offsetting the logistical problems associated with high transportation costs. As a result, the main parameters for the use of sugarcane bagasse as an energy source were identified. This review and analytical study brings together data obtained by previous research works in order to present and consolidate important information related to the physical and chemical characterization of sugarcane bagasse for energy purposes, as well as to compare the results obtained by the characterization, in order to indicate another option for creating a potential value chain for the energy recovery of this product.

2. Raw Material Characterization

Sugarcane bagasse is the solid residue produced in sugar mills after the extraction of juice, and over the years, it has become an important energy input [46]. Thus, it is necessary to know its characteristics in order to use it efficiently with adequate drying performance for the generation of steam, pyrolysis, or gasification, or for hydrolysis [47]. Sugarcane, Saccharum officinarum L. (Poaceae), has been known since 8000 BC and is one of six species of the genus Saccharum, which is a group of tall grasses from Southeast Asia. The stems are the parts from which sugar juice and bagasse are produced [46]. However, leaves and other parts can also play an important role in the generation of energy, mainly in co-generation systems, as described by Sampaio et al. (2019) [48]. The composition of sugarcane is approximately 86 to 92% juice and 8 to 14% fibrous material [46]. This depends not only on the composition of stems, but also on other factors, such as the plant variety, number of tips and leaves, maturation, harvesting period, whether it was burned or not before harvesting, whether the harvest was mechanized or manual, and climatic factors such as whether it rained or not during the plant growth period [49]. Physical and chemical characteristics of sugarcane bagasse have a direct influence on its use as an energy source. The commonly used method is bagasse combustion in steam generators, and knowledge of bagasse characteristics is necessary for the design of steam generation equipment [46]. Figure 1 shows a scheme of the sugar and sugarcane bagasse production process. As can be seen from the process diagram shown in the figure, after cutting the sugarcane, the materials are successively processed through a set of roller mills, where the cane juice is extracted. This juice subsequently undergoes an evaporation process in order to eliminate excess water and concentrate the sugar. In the end, the juice also undergoes a centrifugation process to eliminate all remaining water and any solid particles, namely fibrous remains of the cane. After the pressing process by the roller mills, the sugarcane gives way to bagasse. This is partly consumed to feed the furnace that provides the heat for the evaporation of water from the cane juice, while another part is left over as final waste [50].
Sugarcane bagasse is a complex mixture of cellulose, hemicellulose, and lignin, which make up the cells of the walls in vascular bundles [51]. The amount of fiber in the stems depends on the length and diameter of the stems. The number of nodes and the distance between nodes influence the amount of fiber obtained in the extraction [46]. Cellulose is a high-molecular-weight polymer composed largely of glucose units. Hemicellulose is largely composed of xylose units with small parts of arabinose, both with five carbons in the molecular structure (pentose), as opposed to glucose, which has six carbons in its molecular structure (hexose). Lignin is a complex substance composed largely of aromatic phenolic compounds that generally give the sugarcane fiber its stiffness [52,53,54]. The relative amounts of these compounds depend on the variety of the cane, the age, and the size of the stems. There are also small amounts of inorganic compounds, such as calcium and silica, present in the cellular structures, but these do not have a significant effect on the overall fiber composition [55]. Ash is an inorganic compound found in the bagasse structure, and its composition depends on the plant species, soil, type of fertilization, and inorganic materials dragged during harvesting, which can be mechanized or manual. The main elements are silica, potassium, calcium, phosphorus, magnesium, and other inorganics [56,57,58].
In a study, de Moraes Rocha et al. (2015) collected 60 samples of sugarcane bagasse from industrial sugar and alcohol production units located in São Paulo and northeastern Brazil [60]. These bagasse samples were selected to include different varieties of sugarcane, and to be representative of the types of soils and climates in different geographical regions and with different harvesting methods. It is a common practice to plant mixed varieties of sugarcane, which grow side-by-side and are harvested simultaneously, as a way to avoid the proliferation of pests. Collected samples were later ground and analyzed in the laboratory. Table 1 shows the results obtained for all samples, summarizing the representative composition of sugarcane, as well as the results obtained in a previous study conducted by Triana et al. (1990). As can be seen from the results, sugarcane bagasse is, on average, made up of 42.2% cellulose, 27.6% hemicellulose, 21.6% lignin, 5.63% extractive compounds, and 2.84% ash, with a standard deviation of 1.93, 0.88, 1.67, 2.31, and 1.22, and a coefficient of variation of 4.6, 3.2, 7.7, 41.0, and 43.0, respectively. As can also be inferred from the statistical analysis presented in Table 2, in general, the composition of main components did not differ significantly between samples. These results are in line with previous studies by the same authors [61,62], but also with other studies [55]. They are also in agreement with those presented by Triana et al. (1990), who classified the average values as being in the range of 40% to 50% for cellulose, 25% to 30% for hemicellulose, and 20% to 25% for lignin [63]. The extractables and ash content obtained in the study show a dispersion trend, which is justified by the fact that these parameters are dependent on the conditions where the plants grow [60].

3. Materials and Methods

3.1. Material Sampling

In order to verify the evolution of sugarcane bagasse properties resulting from the torrefaction process, several analyses were carried out to characterize them. Different techniques were used, including proximate analysis (fixed carbon content, volatiles, ash, and moisture), ultimate analysis (C, H, O, and N), and heating value. In order to carry out this study, 10 kg was purchased in a commercial retail area, with the sugarcane identified as having originated in Costa Rica. This is the only way to acquire sugarcane in mainland Portugal, since it is an exotic agricultural product that does not grow in the territory. However, on the island of Madeira, sugarcane is a traditional agricultural crop that has been explored for centuries, and despite being less important than in other times, it continues to be used for the production of sugar and its derivatives—specifically cane spirit, a drink similar to Caribbean rum, and Brazilian cachaça, which is used in the production of poncha, a typical Madeiran drink.

3.2. Sample Preparation and Thermal Treatment

The next step was to produce laboratory samples similar to sugarcane bagasse through the industrial process. Thus, the canes were processed using a 4-roller Roskamp mill, simulating the industrial process. Then, the canes were washed several times with running water, to eliminate as much sugar as possible, and cut into small pieces with an average size of 20 × 10 × 5 mm, which were dried in an ECOCELL forced air oven at a temperature of 90 °C for 24 h. After this initial drying period, the material was washed to extract the sugar by placing in water for 12 h, after which the water was renewed. This process was repeated 3 more times, until it was found that the water was clean and colorless. After the washing process, the pieces of sugarcane were dried for an additional 12 h at 90 °C. Figure 2 shows the sequence from raw material to sugarcane pieces used in the torrefaction test.
In this work, a torrefaction protocol described by Ribeiro et al. (2018) was used [64]. The samples were torrefied and pyrolyzed in the muffle furnace, which has a built-in controller with the ability to program 4 temperature thresholds and the residence time. There is a cavity on the top of the device to facilitate the extraction of torrefaction gases. Then, the muffle furnace was programmed to the desired temperature (°C) and residence time (minutes), with each level corresponding to a torrefaction phase. Sample preparation started by weighing approximately 0.5 kg of material. Preparation was aided by conventional aluminum foil with the objective to wrap the sugarcane bagasse in a cylindrical shape. During this study, torrefaction tests were carried out in triplicate to guarantee their reproducibility (Figure 3).
The particular parameters that can be changed during the thermal process are temperature and residence time, which were changed in order to understand the best set of parameters to obtain high-quality samples. Table 3 defines the parameters used for each test performed. It should be noted that the selection of parameters described in the table was done in a sequential manner, taking into account the results obtained for each torrefaction type. That is, the results obtained in one process always influenced the choice of parameters used in the next one. Obtained materials are shown in Figure 4.

3.3. Ultimate Analysis

Ultimate analysis was performed in a LECO CHN628 in accordance with the standard EN 15104: 2011, Solid Biofuels—Determination of Total Content of Carbon, Hydrogen and Nitrogen—Instrumental Methods. The oxygen content on a dry basis was determined from Equation (1), as follows:
w(O) = 100 − w(C) − w(H) − w(N)
where w(O) is oxygen content (%), w(C) is carbon content (%), w(H) is hydrogen content (%), and w(N) is nitrogen content (%).

3.4. Proximate Analysis

Thermogravimetric (TGA) analysis was conducted in accordance with the standards EN 14775: 2009, Solid Biofuels—Determination of Ash Content; EN 15148: 2009, Solid Biofuels—Determination of Volatiles Content; and EN 14774-3: 2009, Solid Biofuel—Determination of Moisture Content, using an ELTRA Thermostep equipment.

3.5. Determination of Heating Value

When the moisture content of the biomass is very low, the difference between the higher heating value (HHV) and lower heating value (LHV) is almost zero, and for this study, only the HHV of the samples was determined. HHV can be estimated, in MJ·kg−1, based on the C, H, O, and N content, as shown in Equation (2) [65,66]:
HHV (MJ·kg−1) = (33.5[C] + 142.3[H] − 15.4[O] − 14.5[N]) × 10−2
where C is carbon content, H is hydrogen content, O is oxygen content, and N is nitrogen content.

3.6. Specific Density and Energy Density

Lastly, the parameters energy densification ratio (EDR), mass yield (MY), and energy yield (EY) were analyzed. The calculations were made through Equations (3)–(5), according to Grigiante and Antolini [67], as follows:
EDR = HHV dried   torrefied   biomass HHV dried   raw   biomass
where HHVdried torrefied biomass is the high heating value of dried torrefied biomass and HHVdried raw biomass is the high heating value of dried raw biomass;
MY ( % ) = w dried   torrefied   biomass w dried   raw   biomass × 100
where wdried torrefied biomass is the mass of dried torrefied biomass and wdried raw biomass is the mass of dried raw biomass; and
EY ( % ) = MY × EDR
where MY is the mass yield ratio (%) and EDR is the energy densification ratio.

4. Results

The results obtained in the laboratory analysis are presented in Table 4, Table 5 and Table 6 for the dried samples, samples processed at 200 °C, and samples processed at 300 °C, respectively. All analyses were conducted in triplicate, and average values and standard deviation for all tests and calculations were determined.
Table 4 presents the results obtained for samples after drying. As can be seen in the results of elementary analysis, the average values obtained for carbon, hydrogen, nitrogen, and oxygen were 47.40%, 6.59%, 0.11%, and 45.99%, with standard deviations of 0.58, 0.39, 0.02, and 0.53, respectively. Thermogravimetric analysis gave mean values for fixed carbon, volatiles, ash, and moisture of 16.38%, 81.25%, 1.36%, and 3.31%, with standard deviations of 0.13, 1.30, 0.10, and 0.51, respectively. The HHV, calculated using Equation (2), presented an average value of 18.17 MJ·kg−1 with a standard deviation of 0.55.
Table 5 presents the results obtained for the samples after thermal treatment at 200 °C. As can be seen in the results of elementary analysis, average values obtained for carbon, hydrogen, nitrogen, and oxygen were 53.16%, 6.44%, 0.12%, and 40.28%, with standard deviations of 2.42, 0.19, 0.01, and 2.32, respectively. Thermogravimetric analysis gave mean values for fixed carbon, volatiles, ash, and moisture of 20.79%, 77.74%, 1.48%, and 1.03%, with standard deviations of 0.60, 1.35, 0.38, and 0.22, respectively. The HHV, calculated using Equation (2), presented an average value of 20.75 MJ·kg−1 with a standard deviation of 1.03. The average weight of samples used in this test at 200 °C was 505.83 g, with a standard deviation of 3.85, and the average weight of samples after the test was 415.62 g, with a standard deviation of 5.17. This difference indicates an average loss of mass of 17.83%, with a standard deviation of 1.21. The calculation of EDR, MY, and EY presented average values of 1.14%, 82.17%, and 93.95%, with standard deviations of 0.08, 1.21, and 5.84, respectively.
Table 6 presents the results obtained for the samples after thermal treatment at 300 °C, according to the procedure presented in Section 3.2. As can be seen in the results of the elementary analysis, the average values obtained for carbon, hydrogen, nitrogen, and oxygen were 78.61%, 6.54%, 0.43%, and 14.42%, to standard deviations of 1.21, 0.14, 0.04, and 1.15, respectively. Thermogravimetric analysis gave mean values for fixed carbon, volatiles, ash, and moisture of 68.52%, 27.10%, 4.39%, and 3.79%, with standard deviations of 1.56, 1.90, 0.37, and 0.30, respectively. The HHV, calculated using Equation (2), presented an average value of 33.36 MJ·kg−1, to a standard deviation of 0.47. The average weight of the samples used in this test at 300 °C was 507.86 g, with a standard deviation of 4.60, and the average weight after the test was 156.45 g, with a standard deviation of 4.99. This difference indicates an average loss of mass of 69.20%, with a standard deviation of 0.77. The calculation of EDR, MY, and EY presented average values of 1.84%, 30.80%, and 56.69%, with standard deviations of 0.08, 0.77, and 3.80, respectively.

5. Discussion

Biomass has lower density, higher moisture content, and lower heating value compared with fossil fuels [68]. The diversity of sources and seasonality of some raw materials introduce challenges related to logistics that hinder their use on a larger scale [69]. In an attempt to address these drawbacks, we need to homogenize raw materials in order to produce more energy-dense fuel [70].
Torrefaction is a process that subjects materials to temperatures from 220 to 320 °C in the absence of oxygen [71]. The thermal decomposition of biomass begins with the evaporation of water and extractives up to 150 °C. Between 150 and 220 °C, there is a slow process of depolymerization of hemicellulose with the emission of certain lipophilic compounds, and the material starts to show structural deformity in the plant tissue [72]. Between 220 and 320 °C, torrefaction is carried out, involving the volatilization of hemicellulose and depolymerization and partial volatilization of lignin and cellulose [73]. The release of hydrophilic extractives such as oxygenated compounds, carboxylic acids with high molecular weight, alcohols, and aldehydes, among other gases, with the complete destruction of the plant cell structure, results in a more brittle material [74]. Above 300 °C, the other compounds present in the biomass volatilize, resulting in the beginning of the pyrolysis process [75].
In general, the composition of torrefied biomass shows an increase in the fixed carbon content as torrefaction severity increases [76]. Since it has a lower O/C due to the volatilization and transformation of chemical components, the proportion of carbon in the elemental chemical composition is increased, and this directly contributes to the increased heating value [77].
The ultimate analysis of a fuel characterizes its chemical composition in terms of its main chemical elements, which are normally represented by C, H, O, and N. The performance of biomass as a fuel is directly related to its chemical composition. The work of de Moraes Rocha et al. (2015) presented the results of the ultimate analysis of 60 samples of sugarcane bagasse, of which the average values are shown in Table 7 [60].
Table 7 shows that the carbon content of biomass is about 45%, with a standard deviation of 1.1%. This deviation is acceptable considering the heterogeneity of the sample and the final objective of this material: thermal conversion. According to the results presented in Table 7, these samples had an average carbon/hydrogen ratio of 7:1, an average carbon/oxygen ratio of 1:1, an average carbon/nitrogen ratio of 166:1, and an average oxygen/hydrogen ratio of 8:1 [60]. The decreased atomic ratios of O/C and H/C in relation to untreated biomass make it possible to compare the characteristics of torrefaction biomass with other solid fuels, such as mineral coal and charcoal, using the Van Krevelen diagram (Figure 5). Calculating the H/C and O/C ratios for the analyzed samples, the results shown in Table 8 were obtained; then, they were projected onto the Van Krevelen diagram shown in Figure 5. The black dots represent the analyzed samples. As can be seen, although one of the samples, produced at 200 °C, already had a higher HHV, it was still projected into the area of untreated biomass, indicating good potential performance with increased temperature, as seen with the heat-treated samples at 300 °C, which were projected into an area corresponding to bituminous coal.
When evaluating the use of torrefied biomass as raw material for other thermochemical conversion processes, it was found that for combustion reactions, the solid product can be used as an industrial fuel in boilers for steam production and in co-combustion with mineral coal. In addition, the possibility of storing it for long periods can also facilitate its domestic use [79,80]. In the literature, torrefaction followed by densification has been reported. Densification is a compaction process that uses equipment such as presses or extruders to increase the durability and improve the physical characteristics of biomass residues [81,82,83,84]. In the case of torrefaction, it is possible to densify the material by briquetting or pelletizing in order to obtain a final product with greater hydrophobic character and high physical and energetic density [85,86]. With this, the material can have standard sizes that favor transportation, storage, and handling, as well as facilitate the feeding of raw materials in industrial and domestic installations [78]. Apparently, for the lowest temperature used in this test, 200 °C, there should be no problems during densification, since even the color of the material is still light to dark brown and not black, as seen in samples treated at lower temperatures. Most likely, the state of lignin and cellulose did not change during the test at 200 °C, but it most certainly did at 300 °C, making it more difficult without the use of binders.
The heating value tends to be higher for torrefied biomass than non-torrefied biomass. However, in contrast to this increase, there is mass loss of the material, as seen in Table 8, and the need to obtain a mass and energy balance to verify the technical–economic application of the thermochemical conversion process to check its feasibility is evident.
From the thermogravimetric analysis, it can be inferred that there is an increased concentration of fixed carbon, which is associated with the loss of hydrogenated compounds, in line with the results presented in the work of Quiroga et al. (2020) [87]. The moisture content decreases from an average value of 3.31% for dry material to an average of 1.03% in material processed at 200 °C. This follows the normal trend, since it is a process of forced drying of nonstructural water, but it is still present in the material. However, when assessing the moisture content of materials processed at 300 °C, it appears that it rises again to 3.79%. This rise should be associated with the release of water contained in the material structure and/or the release of hydroxyl radicals, as was portrayed in the work of Chew and Doshi (2011) [88].
The results presented in Table 5 indicate that a simple heat treatment at 200 °C leads to an average energy densification of 1.14, with MY of 82.17% and EY of 93.85%. That is, even without entering the torrefaction zone, still in the over-drying zone, there was already energy densification in the materials under study. Analyzing the results presented in Table 6, for the materials processed at 300 °C, the energy densification is even more significant, since the EDR reaches an average value of 1.84, with a MY of 30.80% and EY of 56.69%. These values are in line with the values calculated for materials most commonly used in the production of energy from biomass in Europe, such as the maritime pine (Pinus pinaster), which has EDR, MY, and EY values of, respectively, 1.55%, 30.50%, and 47.41% [89]. With the results related to the direct increase of heating value, but mainly with the EDR values, there is an energetic densification of the materials. This increase in energy density allows an evaluation of the possibility of exporting materials, especially if they are subjected to a densification process, for example, through the production of pellets [90]. This can contribute to the optimization of logistical processes, which still need to be evaluated and quantified [91]. The combination of the improvement of properties related to logistics, namely the increase in energy density, is in accordance with the properties found in commercial coals, namely bituminous and sub-bituminous coals. In fact, with the energy content above 25 MJ·kg−1, the heat-treated sugarcane bagasse approaches the values that these coals normally present. Thus, the torrefied sugarcane bagasse presents itself as a real alternative for the replacement of coal in the thermoelectric plants, especially because, as presented in the work of Nunes et al. (2020), in addition to the energy properties, most of the torrefied biomasses have other properties that allow this substitution, namely the Hardgrove Grindability Index (HGI), which also presents similar values to those of coal [92].

6. Conclusions and Future Developments

The sugarcane industry presents environmental problems, since it generates large amounts of waste that are normally valued energetically in sugar mills. However, growth in the industry has also led to increased production of waste, making it impossible to discharge the quantities generated. These residues have the potential to be exported for energy recovery in other areas, namely in Europe, where the demand for and consumption of biomass for energy has assumed particular importance. However, the low density of the material, associated with other problems common to biomass such as fermentation of the product, make export very difficult and costly.
The possibility of using thermochemical conversion technologies such as torrefaction to improve the energy potential of sugarcane bagasse presents itself as a highly promising alternative, as demonstrated by the results obtained in the tests performed. The improved energetic properties associated with energy densification make heat-treated sugarcane bagasse an asset to the energy market, mainly regarding the replacement of coal in the large-scale generation of energy.
Further studies are still needed, mainly to define the optimal temperature to be used in torrefaction, since high mass loss can hinder the economic viability of projects, by using, for example, a response surface methodology (RSM), which explores the relationships between several explanatory variables and one or more response variables. It is also necessary to carry out new tests with a larger number of samples, so that the results can be statistically validated, since in the present study, it was not possible to carry out a statistical study of the results, because, as previously mentioned, the tests were only conducted in triplicate. An assessment of the supply chain factors, namely those related to transport costs and cargo conditioning in long-distance transport, similar to what already happens with wood pellet supply chains, should be carried out as well. Associated with this issue, there is also a need to carry out studies on the potential for mechanical densification through the production of pellets or briquettes of the resulting torrefied material.

Author Contributions

Conceptualization, L.J.R.N.; methodology, L.J.R.N. and H.F.C.S.; validation, L.J.R.N., L.C.R.S. and L.M.E.F.L.; formal analysis, L.J.R.N.; investigation, L.J.R.N., L.C.R.S., and L.M.E.F.L.; resources, H.F.C.S.; data curation, L.J.R.N., L.C.R.S., and L.M.E.F.L.; writing—original draft preparation, L.J.R.N.; writing—review and editing, L.J.R.N. and H.F.C.S.; supervision, L.J.R.N.; funding acquisition, H.F.C.S. All authors have read and agreed to the published version of the manuscript.

Funding

This research received no external funding.

Acknowledgments

The authors would like to acknowledge the Portuguese companies Yser Green Energy SA and Advanced Fuel Solutions SA, which allowed the execution of the laboratory tests.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Dotaniya, M.; Datta, S.; Biswas, D.; Dotaniya, C.; Meena, B.; Rajendiran, S.; Regar, K.; Lata, M. Use of sugarcane industrial by-products for improving sugarcane productivity and soil health. Int. J. Recycl. Org. Waste Agric. 2016, 5, 185–194. [Google Scholar] [CrossRef] [Green Version]
  2. Zhang, N.; Wang, M.; Wang, N. Precision agriculture—A worldwide overview. Comput. Electron. Agric. 2002, 36, 113–132. [Google Scholar] [CrossRef]
  3. Khoury, C.K.; Achicanoy, H.A.; Bjorkman, A.D.; Navarro-Racines, C.; Guarino, L.; Flores-Palacios, X.; Engels, J.M.; Wiersema, J.H.; Dempewolf, H.; Sotelo, S. Origins of food crops connect countries worldwide. Proc. R. Soc. B Biol. Sci. 2016, 283, 20160792. [Google Scholar] [CrossRef]
  4. Fischer, G.; Teixeira, E.; Hizsnyik, E.T.; Velthuizen, H.V. Land use dynamics and sugarcane production. In Sugarcane Ethanol: Contribution to Climate Change Mitigation and the Environment; Wageningen Academic: Wageningen, DC, USA, 2008; pp. 29–62. [Google Scholar]
  5. Goldemberg, J.; Coelho, S.T.; Guardabassi, P. The sustainability of ethanol production from sugarcane. Energy Policy 2008, 36, 2086–2097. [Google Scholar] [CrossRef]
  6. Furtado, A.T.; Scandiffio, M.I.G.; Cortez, L.A.B. The Brazilian sugarcane innovation system. Energy Policy 2011, 39, 156–166. [Google Scholar] [CrossRef]
  7. Goldemberg, J. The Brazilian biofuels industry. Biotechnol. Biofuels 2008, 1, 6. [Google Scholar] [CrossRef] [Green Version]
  8. Awwal, O.A.; Israel, O.K.; Yashim, Z. Physico-chemical, Calorific, and Emission Performance of Briquettes Produced from Maize Cob, Sugarcane Bagasse, and Polythene Composites. Avicenna J. Environ. Health Eng. 2019, 6, 49–54. [Google Scholar] [CrossRef]
  9. Mohammadi, F.; Abdoli, M.; Amidpour, M.; Vahidi, H.; Gitipour, S. Environmental-economic evaluation of sugar cane bagasse gasification power plants versus combined-cycle gas power plants. Glob. J. Environ. Sci. Manag. 2020, 6, 73–84. [Google Scholar]
  10. Carvalho, M.; Segundo, V.; Medeiros, M.; Santos, N.; Coelho Junior, L.M. Carbon footprint of the generation of bioelectricity from sugarcane bagasse in a sugar and ethanol industry. Int. J. Glob. Warm. 2019, 17, 235–251. [Google Scholar] [CrossRef]
  11. Kaab, A.; Sharifi, M.; Mobli, H.; Nabavi-Pelesaraei, A.; Chau, K.-w. Combined life cycle assessment and artificial intelligence for prediction of output energy and environmental impacts of sugarcane production. Sci. Total Environ. 2019, 664, 1005–1019. [Google Scholar] [CrossRef]
  12. Kaab, A.; Sharifi, M.; Mobli, H.; Nabavi-Pelesaraei, A.; Chau, K.-W. Use of optimization techniques for energy use efficiency and environmental life cycle assessment modification in sugarcane production. Energy 2019, 181, 1298–1320. [Google Scholar] [CrossRef]
  13. Valderrama, C.; Quintero, V.; Kafarov, V. Energy and water optimization of an integrated bioethanol production process from molasses and sugarcane bagasse: A Colombian case. Fuel 2020, 260, 116314. [Google Scholar] [CrossRef]
  14. Mohammadi, F.; Roedl, A.; Abdoli, M.A.; Amidpour, M.; Vahidi, H. Life cycle assessment (LCA) of the energetic use of bagasse in Iranian sugar industry. Renew. Energy 2020, 145, 1870–1882. [Google Scholar] [CrossRef]
  15. Asfaw, B.T.; Shebu, H.G.; Gari, M.T. Review on: Case study for the Construction of Particleboard Using Sugarcane Bagasse. J. Catal. Catal. 2019, 6, 14–24. [Google Scholar]
  16. Coelho, R.D.; Lizcano, J.V.; da Silva Barros, T.H.; da Silva Barbosa, F.; Leal, D.P.V.; da Costa Santos, L.; Ribeiro, N.L.; Júnior, E.F.F.; Martin, D.L. Effect of water stress on renewable energy from sugarcane biomass. Renew. Sustain. Energy Rev. 2019, 103, 399–407. [Google Scholar] [CrossRef]
  17. Maqueira-López, L.A.; Morejón-Rivera, R.; Roján-Herrera, O.; Torres-de-la-Noval, W. Relationship between growth traits and yield formation in Indica-type rice crop. Agron. Mesoam. 2019, 30, 79–100. [Google Scholar] [CrossRef]
  18. Ferreira, S.; Moreira, N.A.; Monteiro, E. Bioenergy overview for Portugal. Biomass Bioenergy 2009, 33, 1567–1576. [Google Scholar] [CrossRef]
  19. Maxwell, K. Portugal, Europe, and the Origins of the Atlantic Commercial System, 1415–1520. Port. Stud. 1992, 8, 3–16. [Google Scholar]
  20. Vieira, A. As Ilhas e a expansão da cultura e tecnologia da cana-de-açúcar no Atlântico nos séculos XV a XIX. Labor Eng. 2007, 1, 1–20. [Google Scholar] [CrossRef]
  21. Tamás, S. DOSSIER SUCRE, PASSAT I PRESENT. The Impact of Sugar Cane Expansion on Five Continents. Illes Imp. 2006, 5–16. [Google Scholar] [CrossRef]
  22. Moore, J.W. Madeira, Sugar, and the Conquest of Nature in the “First” Sixteenth Century: Part I: From “Island of Timber” to Sugar Revolution, 1420–1506. Review 2009, 32, 345–390. [Google Scholar]
  23. Moore, J.W. Madeira, Sugar, and the Conquest of Nature in the “First” Sixteenth Century, Part II: From Regional Crisis to Commodity Frontier, 1506–1530. Review 2010, 33, 1–24. [Google Scholar]
  24. Strong, D.R., Jr.; McCoy, E.D.; Rey, J.R. Time and the number of herbivore species: The pests of sugarcane. Ecology 1977, 58, 167–175. [Google Scholar] [CrossRef]
  25. De Souza Caldas, R.M.; Verslype, N.I.; Machado, J. Sustainable agriculture in Ilha da Madeira-Portugal| Agricultura sustentável na Ilha da Madeira-Portugal. Rev. Geama 2016, 2, 376–384. [Google Scholar]
  26. Kiesow, S.; Bork, H.R. Agricultural terraces as a proxy to landscape history on Madeira island, Portugal. Ler História 2017, 71, 127–152. [Google Scholar] [CrossRef]
  27. Moore, J.W. Sugar and the expansion of the early modern world-economy: Commodity frontiers, ecological transformation, and industrialization. Review 2000, 23, 409–433. [Google Scholar]
  28. Silva, P.; Freitas, J.; Silva, C.L.; Perestrelo, R.; Nunes, F.M.; Câmara, J.S. Establishment of authenticity and typicality of sugarcane honey based on volatile profile and multivariate analysis. Food Control 2017, 73, 1176–1188. [Google Scholar] [CrossRef]
  29. Silva, P.; Silva, C.L.; Perestrelo, R.; Nunes, F.M.; Câmara, J.S. Fingerprint targeted compounds in authenticity of sugarcane honey—An approach based on chromatographic and statistical data. LWT 2018, 96, 82–89. [Google Scholar] [CrossRef]
  30. Hofsetz, K.; Silva, M.A. Brazilian sugarcane bagasse: Energy and non-energy consumption. Biomass Bioenergy 2012, 46, 564–573. [Google Scholar] [CrossRef]
  31. Dantas, G.A.; Legey, L.F.; Mazzone, A. Energy from sugarcane bagasse in Brazil: An assessment of the productivity and cost of different technological routes. Renew. Sustain. Energy Rev. 2013, 21, 356–364. [Google Scholar] [CrossRef]
  32. Ramajo-Escalera, B.; Espina, A.; García, J.; Sosa-Arnao, J.; Nebra, S. Model-free kinetics applied to sugarcane bagasse combustion. Thermochim. Acta 2006, 448, 111–116. [Google Scholar] [CrossRef]
  33. Goldemberg, J.; Macedo, I.C. Brazilian alcohol program: An overview. Energy Sustain. Dev. 1994, 1, 17–22. [Google Scholar] [CrossRef]
  34. Boddey, R.M.; Soares, L.H.d.B.; Alves, B.J.; Urquiaga, S. Bio-ethanol production in Brazil. In Biofuels, Solar and Wind as Renewable Energy Systems; Springer: Berlin/Heidelberg, Germany, 2008; pp. 321–356. [Google Scholar]
  35. Turkenburg, W.C.; Faaij, A. Renewable Energy Technologies. In UNDP/UNDESA/WEC: Energy and the Challenge of Sustainability; World Energy Report; UNDP: New York, NY, USA, 2000. [Google Scholar]
  36. Monteiro, S.; Rodriquez, R.; De Souza, M.; d’Almeida, J. Sugar cane bagasse waste as reinforcement in low cost composites. Adv. Perform. Mater. 1998, 5, 183–191. [Google Scholar] [CrossRef]
  37. Botha, T.; Von Blottnitz, H. A comparison of the environmental benefits of bagasse-derived electricity and fuel ethanol on a life-cycle basis. Energy Policy 2006, 34, 2654–2661. [Google Scholar] [CrossRef]
  38. Omer, A.M. Green energies and the environment. Renew. Sustain. Energy Rev. 2008, 12, 1789–1821. [Google Scholar] [CrossRef]
  39. Rosillo-Calle, F. A review of biomass energy—Shortcomings and concerns. J. Chem. Technol. Biotechnol. 2016, 91, 1933–1945. [Google Scholar] [CrossRef]
  40. Naik, S.N.; Goud, V.V.; Rout, P.K.; Dalai, A.K. Production of first and second generation biofuels: A comprehensive review. Renew. Sustain. Energy Rev. 2010, 14, 578–597. [Google Scholar] [CrossRef]
  41. Demirbas, A. Biofuels sources, biofuel policy, biofuel economy and global biofuel projections. Energy Convers. Manag. 2008, 49, 2106–2116. [Google Scholar] [CrossRef]
  42. Samariha, A.; Khakifirooz, A. Application of NSSC pulping to sugarcane bagasse. BioResources 2011, 6, 3313–3323. [Google Scholar]
  43. Lois-Correa, J. Depithers for efficient preparation of sugar cane bagasse fibers in pulp and paper industry. Ing. Investig. Tecnol. 2012, 13, 417–424. [Google Scholar] [CrossRef] [Green Version]
  44. Hemmasi, A.H.; Samariha, A.; Tabei, A.; Nemati, M.; Khakifirooz, A. Study of morphological and chemical composition of fibers from Iranian sugarcane bagasse. Am. Eurasian J. Agric. Environ. Sci 2011, 11, 478–481. [Google Scholar]
  45. Loh, Y.; Sujan, D.; Rahman, M.E.; Das, C.A. Sugarcane bagasse—The future composite material: A literature review. Resour. Conserv. Recycl. 2013, 75, 14–22. [Google Scholar] [CrossRef]
  46. Bizzo, W.A.; Lenço, P.C.; Carvalho, D.J.; Veiga, J.P.S. The generation of residual biomass during the production of bio-ethanol from sugarcane, its characterization and its use in energy production. Renew. Sustain. Energy Rev. 2014, 29, 589–603. [Google Scholar] [CrossRef]
  47. Lombardi, L.; Carnevale, E.; Corti, A. A review of technologies and performances of thermal treatment systems for energy recovery from waste. Waste Manag. 2015, 37, 26–44. [Google Scholar] [CrossRef]
  48. Sampaio, I.L.; Cardoso, T.F.; Souza, N.R.; Watanabe, M.D.; Carvalho, D.J.; Bonomi, A.; Junqueira, T.L. Electricity production from sugarcane straw recovered through bale system: Assessment of retrofit projects. Bioenergy Res. 2019, 12, 865–877. [Google Scholar] [CrossRef] [Green Version]
  49. Saidur, R.; Abdelaziz, E.; Demirbas, A.; Hossain, M.; Mekhilef, S. A review on biomass as a fuel for boilers. Renew. Sustain. Energy Rev. 2011, 15, 2262–2289. [Google Scholar] [CrossRef]
  50. Dias, M.O.; Ensinas, A.V.; Nebra, S.A.; Maciel Filho, R.; Rossell, C.E.; Maciel, M.R.W. Production of bioethanol and other bio-based materials from sugarcane bagasse: Integration to conventional bioethanol production process. Chem. Eng. Res. Des. 2009, 87, 1206–1216. [Google Scholar] [CrossRef]
  51. Rezende, C.A.; de Lima, M.A.; Maziero, P.; deAzevedo, E.R.; Garcia, W.; Polikarpov, I. Chemical and morphological characterization of sugarcane bagasse submitted to a delignification process for enhanced enzymatic digestibility. Biotechnol. Biofuels 2011, 4, 54. [Google Scholar] [CrossRef] [Green Version]
  52. Sun, J.; Sun, X.; Zhao, H.; Sun, R. Isolation and characterization of cellulose from sugarcane bagasse. Polym. Degrad. Stab. 2004, 84, 331–339. [Google Scholar] [CrossRef]
  53. Cerqueira, D.A.; Rodrigues Filho, G.; da Silva Meireles, C. Optimization of sugarcane bagasse cellulose acetylation. Carbohydr. Polym. 2007, 69, 579–582. [Google Scholar] [CrossRef]
  54. De Souza, A.P.; Leite, D.C.; Pattathil, S.; Hahn, M.G.; Buckeridge, M.S. Composition and structure of sugarcane cell wall polysaccharides: Implications for second-generation bioethanol production. Bioenergy Res. 2013, 6, 564–579. [Google Scholar] [CrossRef]
  55. Sanjuan, R.; Anzaldo, J.; Vargas, J.; Turrado, J.; Patt, R. Morphological and chemical composition of pith and fibers from Mexican sugarcane bagasse. Eur. J. Wood Wood Prod. 2001, 59, 447–450. [Google Scholar] [CrossRef]
  56. Frías, M.; Villar, E.; Savastano, H. Brazilian sugar cane bagasse ashes from the cogeneration industry as active pozzolans for cement manufacture. Cem. Concr. Compos. 2011, 33, 490–496. [Google Scholar] [CrossRef]
  57. Payá, J.; Monzó, J.; Borrachero, M.V.; Díaz-Pinzón, L.; Ordonez, L.M. Sugar-cane bagasse ash (SCBA): Studies on its properties for reusing in concrete production. J. Chem. Technol. Biotechnol. Int. Res. Process Environ. Clean Technol. 2002, 77, 321–325. [Google Scholar] [CrossRef]
  58. Teixeira, S.R.; De Souza, A.E.; de Almeida Santos, G.T.; Vilche Pena, A.F.; Miguel, A.G. Sugarcane bagasse ash as a potential quartz replacement in red ceramic. J. Am. Ceram. Soc. 2008, 91, 1883–1887. [Google Scholar] [CrossRef]
  59. Pandey, A.; Soccol, C.R.; Nigam, P.; Soccol, V.T. Biotechnological potential of agro-industrial residues. I: Sugarcane bagasse. Bioresour. Technol. 2000, 74, 69–80. [Google Scholar] [CrossRef]
  60. De Moraes Rocha, G.J.; Nascimento, V.M.; Gonçalves, A.R.; Silva, V.F.N.; Martín, C. Influence of mixed sugarcane bagasse samples evaluated by elemental and physical–chemical composition. Ind. Crop. Prod. 2015, 64, 52–58. [Google Scholar] [CrossRef]
  61. Rocha, G.J.d.M.; Silva, F.; Curvelo, A.A.D.S.; Araujo, G.T. A fast and accurate method for determination of cellulose and polyoses by HPLC. In Proceedings of the 5th Brazilian Symposium on Chemistry of Lignins and Other Wood Components, Curitiba, Brazil, 31 August–4 September 1997. [Google Scholar]
  62. Gouveia, E.R.; Nascimento, R.T.d.; Souto-Maior, A.M.; Rocha, G.J.d.M. Validação de metodologia para a caracterização química de bagaço de cana-de-açúcar. Química Nova 2009, 32, 1500–1503. [Google Scholar] [CrossRef]
  63. Triana, O.; Leonard, M.; Saavedra, F.; Fernández, N.; Gálvez, G. Atlas del Bagazo de la Caña de Azucar; Grupo de Paises Latinoamericanos y del Caribe Exportadores de Azucar: Mexico City, Mexico, 1990. [Google Scholar]
  64. Ribeiro, J.M.C.; Godina, R.; Matias, J.C.d.O.; Nunes, L.J.R. Future perspectives of biomass torrefaction: Review of the current state-of-the-art and research development. Sustainability 2018, 10, 2323. [Google Scholar] [CrossRef] [Green Version]
  65. Demirbaş, A. Calculation of higher heating values of biomass fuels. Fuel 1997, 76, 431–434. [Google Scholar] [CrossRef]
  66. Demirbas, A. Combustion characteristics of different biomass fuels. Prog. Energy Combust. Sci. 2004, 30, 219–230. [Google Scholar] [CrossRef]
  67. Grigiante, M.; Antolini, D. Experimental results of mass and energy yield referred to different torrefaction pathways. Waste Biomass Valorization 2014, 5, 11–17. [Google Scholar] [CrossRef]
  68. Nunes, L.; Matias, J.; Catalão, J. A review on torrefied biomass pellets as a sustainable alternative to coal in power generation. Renew. Sustain. Energy Rev. 2014, 40, 153–160. [Google Scholar] [CrossRef]
  69. Yue, D.; You, F.; Snyder, S.W. Biomass-to-bioenergy and biofuel supply chain optimization: Overview, key issues and challenges. Comput. Chem. Eng. 2014, 66, 36–56. [Google Scholar] [CrossRef]
  70. Elliott, L.G.; Feehan, C.; Laurens, L.M.; Pienkos, P.T.; Darzins, A.; Posewitz, M.C. Establishment of a bioenergy-focused microalgal culture collection. Algal Res. 2012, 1, 102–113. [Google Scholar] [CrossRef]
  71. Ronsse, F.; Van Hecke, S.; Dickinson, D.; Prins, W. Production and characterization of slow pyrolysis biochar: Influence of feedstock type and pyrolysis conditions. GCB Bioenergy 2013, 5, 104–115. [Google Scholar] [CrossRef]
  72. Kundu, K.; Chatterjee, A.; Bhattacharyya, T.; Roy, M.; Kaur, A. Thermochemical conversion of biomass to bioenergy: A review. In Prospects of Alternative Transportation Fuels; Springer: Berlin/Heidelberg, Germany, 2018; pp. 235–268. [Google Scholar]
  73. Chen, D.; Gao, A.; Cen, K.; Zhang, J.; Cao, X.; Ma, Z. Investigation of biomass torrefaction based on three major components: Hemicellulose, cellulose, and lignin. Energy Convers. Manag. 2018, 169, 228–237. [Google Scholar] [CrossRef]
  74. Beyene, D.; Chae, M.; Dai, J.; Danumah, C.; Tosto, F.; Demesa, A.G.; Bressler, D.C. Enzymatically-mediated Co-production of cellulose nanocrystals and fermentable sugars. Catalysts 2017, 7, 322. [Google Scholar] [CrossRef] [Green Version]
  75. Melchior, T.; Perkins, C.; Lichty, P.; Weimer, A.W.; Steinfeld, A. Solar-driven biochar gasification in a particle-flow reactor. Chem. Eng. Process. Process Intensif. 2009, 48, 1279–1287. [Google Scholar] [CrossRef]
  76. Iroba, K.L.; Baik, O.D.; Tabil, L.G. Torrefaction of biomass from municipal solid waste fractions II: Grindability characteristics, higher heating value, pelletability and moisture adsorption. Biomass Bioenergy 2017, 106, 8–20. [Google Scholar] [CrossRef]
  77. Al-Wabel, M.I.; Al-Omran, A.; El-Naggar, A.H.; Nadeem, M.; Usman, A.R. Pyrolysis temperature induced changes in characteristics and chemical composition of biochar produced from conocarpus wastes. Bioresour. Technol. 2013, 131, 374–379. [Google Scholar] [CrossRef]
  78. Van der Stelt, M.; Gerhauser, H.; Kiel, J.; Ptasinski, K. Biomass upgrading by torrefaction for the production of biofuels: A review. Biomass Bioenergy 2011, 35, 3748–3762. [Google Scholar] [CrossRef]
  79. Felfli, F. Torrefação de Biomassa, Viabilidade Técnica e Potencial de Mercado. Ph.D. Thesis, Faculdade de Engenharia Mecânica (UNICAMP), Campinas, Brazil, 2003; p. 137. [Google Scholar]
  80. Felfli, F.F.; Luengo, C.A.; Rocha, J.D. Torrefied briquettes: Technical and economic feasibility and perspectives in the Brazilian market. Energy Sustain. Dev. 2005, 9, 23–29. [Google Scholar] [CrossRef]
  81. Tumuluru, J.S.; Wright, C.T.; Hess, J.R.; Kenney, K.L. A review of biomass densification systems to develop uniform feedstock commodities for bioenergy application. Biofuels Bioprod. Biorefin. 2011, 5, 683–707. [Google Scholar] [CrossRef]
  82. Kaliyan, N.; Morey, R.V. Factors affecting strength and durability of densified biomass products. Biomass Bioenergy 2009, 33, 337–359. [Google Scholar] [CrossRef]
  83. Manickam, I.N.; Ravindran, D.; Subramanian, P. Biomass densification methods and mechanism. Cogener. Distrib. Gener. J. 2006, 21, 33–45. [Google Scholar] [CrossRef]
  84. Stelte, W.; Sanadi, A.R.; Shang, L.; Holm, J.K.; Ahrenfeldt, J.; Henriksen, U.B. Recent developments in biomass pelletization–A review. BioResources 2012, 7, 4451–4490. [Google Scholar]
  85. Oladeji, J. Theoretical aspects of biomass briquetting: A review study. J. Energy Technol. Policy 2015, 5, 72–81. [Google Scholar]
  86. Tumuluru, J.S.; Cafferty, K.G.; Kenney, K.L. Techno-economic analysis of conventional, high moisture pelletization and briquetting process. In Proceedings of the American Society of Agricultural and Biological Engineers Annual Meeting, Montreal, QC, Canada, 13–16 July 2014; p. 1. [Google Scholar]
  87. Quiroga, E.; Moltó, J.; Conesa, J.A.; Valero, M.F.; Cobo, M. Kinetics of the Catalytic Thermal Degradation of Sugarcane Residual Biomass over Rh-Pt/CeO2-SiO2 for Syngas Production. Catalysts 2020, 10, 508. [Google Scholar] [CrossRef]
  88. Chew, J.J.; Doshi, V. Recent advances in biomass pretreatment–Torrefaction fundamentals and technology. Renew. Sustain. Energy Rev. 2011, 15, 4212–4222. [Google Scholar] [CrossRef]
  89. Rodrigues, A.; Loureiro, L.; Nunes, L. Torrefaction of woody biomasses from poplar SRC and Portuguese roundwood: Properties of torrefied products. Biomass Bioenergy 2018, 108, 55–65. [Google Scholar] [CrossRef]
  90. Conag, A.T.; Villahermosa, J.E.R.; Cabatingan, L.K.; Go, A.W. Energy densification of sugarcane bagasse through torrefaction under minimized oxidative atmosphere. J. Environ. Chem. Eng. 2017, 5, 5411–5419. [Google Scholar] [CrossRef]
  91. Kutlu, O.; Kocar, G. Upgrading lignocellulosic waste to fuel by torrefaction: Characterisation and process optimization by response surface methodology. Int. J. Energy Res. 2018, 42, 4746–4760. [Google Scholar] [CrossRef]
  92. Nunes, L.J. Torrefied Biomass as an Alternative in Coal-Fueled Power Plants: A Case Study on Grindability of Agroforestry Waste Forms. Clean Technol. 2020, 2, 270–289. [Google Scholar] [CrossRef]
Figure 1. Simplified sugar production process (adapted from [59]).
Figure 1. Simplified sugar production process (adapted from [59]).
Applsci 10 06481 g001
Figure 2. Sequence of procedures to obtain sugarcane pieces used in torrefaction tests: (a) raw material as bought; (b) sugarcane after being processed with the roller mill; (c) sugarcane pieces; and (d) pieces being washed.
Figure 2. Sequence of procedures to obtain sugarcane pieces used in torrefaction tests: (a) raw material as bought; (b) sugarcane after being processed with the roller mill; (c) sugarcane pieces; and (d) pieces being washed.
Applsci 10 06481 g002
Figure 3. Sugarcane bagasse sample wrapped in aluminum foil.
Figure 3. Sugarcane bagasse sample wrapped in aluminum foil.
Applsci 10 06481 g003
Figure 4. Obtained materials: (a) after drying; (b) after torrefaction at 200 °C; and (c) after torrefaction at 300 °C.
Figure 4. Obtained materials: (a) after drying; (b) after torrefaction at 200 °C; and (c) after torrefaction at 300 °C.
Applsci 10 06481 g004
Figure 5. Van Krevelen diagram (adapted from [78]).
Figure 5. Van Krevelen diagram (adapted from [78]).
Applsci 10 06481 g005
Table 1. Sugarcane production and area of cultivation in 20 main countries [11,12].
Table 1. Sugarcane production and area of cultivation in 20 main countries [11,12].
CountryProductionArea
(Tons/Year)(Hectares)
Brazil768,678,38210,226,205
India348,448,0004,950,000
China123,059,7391,675,215
Thailand87,468,4961,336,575
Pakistan65,450,7041,130,820
Mexico56,446,821781,054
Colombia36,951,213416,626
Australia34,403,004447,204
Guatemala33,533,403259,850
United States of America29,926,210370,530
Indonesia27,158,830472,693
Philippines22,370,546410,104
Argentina21,990,823331,699
Cuba18,890,972442,307
Vietnam16,313,145256,322
Egypt15,760,418137,011
South Africa15,074,610246,937
Myanmar10,437,058163,650
Peru9,832,52687,696
Ecuador8,661,609104,661
Table 2. Typical composition of sugarcane bagasse.
Table 2. Typical composition of sugarcane bagasse.
Triana et al. (1990) [63]de Moraes Rocha et al. (2015) [60]
Cellulose (%)40–5042.19
Hemicellulose (%)25–3027.60
Lignin (%)20–2521.56
Extractives (%)5.63
Ash (%)2.84
Table 3. Temperature and residence times used in the tests.
Table 3. Temperature and residence times used in the tests.
Residence Time (minutes)200 °C300 °C
3018–18018–180
60180–200180–300
90200300
Time required to safely open door and collect material200–50300–50
Table 4. Results obtained in the analysis conducted with dried samples. FC, fixed carbon; HHV, higher heating value.
Table 4. Results obtained in the analysis conducted with dried samples. FC, fixed carbon; HHV, higher heating value.
AnalysisSample 1Sample 2Sample 3AverageStandard Deviation
C (%)47.1246.8748.2147.400.58
H (%)6.217.126.436.590.39
N (%)0.130.090.110.110.02
O (%)46.5445.9245.2545.900.53
FC (%)16.5216.4116.2116.380.13
Volatiles (%)82.6880.4983.5882.251.30
Ash (%)1.231.471.371.360.10
Moisture (%)4.012.793.143.310.51
HHV (MJ·kg−1)17.4418.7518.3218.170.55
Table 5. Results obtained in analysis conducted with samples thermally treated at 200 °C. EDR, energy densification ratio; MY, mass yield; EY, energy yield.
Table 5. Results obtained in analysis conducted with samples thermally treated at 200 °C. EDR, energy densification ratio; MY, mass yield; EY, energy yield.
AnalysisSample 1Sample 2Sample 3AverageStandard Deviation
C (%)53.6349.9955.8753.162.42
H (%)6.626.516.186.440.19
N (%)0.130.100.120.120.01
O (%)39.6243.437.8340.282.32
FC (%)21.4419.9920.9520.790.60
Volatiles (%)76.8979.6576.6977.741.35
Ash (%)1.332.011.111.480.38
Moisture (%)0.841.340.911.030.22
HHV (MJ·kg−1)21.2719.3121.6720.751.03
Initial sample weight (g)501.24505.59510.67505.833.85
Weight after thermal treatment (g)411.92422.93412.01415.625.17
Mass loss (%)17.8216.3519.3217.831.21
EDR1.221.031.181.140.08
MY (%)82.1883.6580.6882.171.21
EY (%)100.2386.1795.4493.955.84
Table 6. Results obtained in analysis of samples thermally treated at 300 °C.
Table 6. Results obtained in analysis of samples thermally treated at 300 °C.
AnalysisSample 1Sample 2Sample 3AverageStandard Deviation
C (%)78.9876.9879.8778.611.21
H (%)6.666.636.346.540.14
N (%)0.430.380.480.430.04
O (%)13.9316.0113.3114.421.15
FC (%)70.3066.5168.7468.521.56
Volatiles (%)24.9029.5426.8727.101.90
Ash (%)3.974.874.344.390.37
Moisture (%)3.404.123.843.790.30
HHV (MJ·kg−1)33.7332.7033.6633.360.47
Initial sample weight (g)510.12501.45512.01507.864.60
Weight after thermal treatment (g)162.07149.93157.34156.454.99
Mass loss (%)68.2370.1069.2769.200.77
EDR1.931.741.841.840.08
MY (%)31.7729.9030.7330.800.77
EY (%)61.4652.1556.4756.693.80
Table 7. Average results of elemental composition of 60 sugarcane bagasse samples (adapted from [60]).
Table 7. Average results of elemental composition of 60 sugarcane bagasse samples (adapted from [60]).
C (%)H (%)O (%)N (%)
Average44.906.1048.740.27
Standard deviation1.070.851.500.10
Table 8. H/C and O/C ratios.
Table 8. H/C and O/C ratios.
SampleH/C × 10O/C
Reference
DriedSample 11.320.99
Sample 21.520.98
SampleSample 31.330.94
Average1.390.97
200 °CSample 11.230.74
Sample 21.300.87
Sample 31.110.68
Average1.210.76
300 °CSample 10.840.18
Sample 20.860.21
Sample 30.790.17
Average0.830.18

Share and Cite

MDPI and ACS Style

Nunes, L.J.R.; Loureiro, L.M.E.F.; Sá, L.C.R.; Silva, H.F.C. Sugarcane Industry Waste Recovery: A Case Study Using Thermochemical Conversion Technologies to Increase Sustainability. Appl. Sci. 2020, 10, 6481. https://doi.org/10.3390/app10186481

AMA Style

Nunes LJR, Loureiro LMEF, Sá LCR, Silva HFC. Sugarcane Industry Waste Recovery: A Case Study Using Thermochemical Conversion Technologies to Increase Sustainability. Applied Sciences. 2020; 10(18):6481. https://doi.org/10.3390/app10186481

Chicago/Turabian Style

Nunes, Leonel J. R., Liliana M. E. F. Loureiro, Letícia C. R. Sá, and Hugo F. C. Silva. 2020. "Sugarcane Industry Waste Recovery: A Case Study Using Thermochemical Conversion Technologies to Increase Sustainability" Applied Sciences 10, no. 18: 6481. https://doi.org/10.3390/app10186481

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop