Correction: Chalivendra et al. Effect of Shear Angle and Printing Orientation on Shear Constitutive Response of Additively Manufactured Acrylonitrile Butadiene Styrene. Polymers 2022, 14, 2484

Letizia, Joshua; Chalivendra, Vijaya; Li, Dapeng

doi:10.3390/polym14153195

Open AccessCorrection

Correction: Chalivendra et al. Effect of Shear Angle and Printing Orientation on Shear Constitutive Response of Additively Manufactured Acrylonitrile Butadiene Styrene. Polymers 2022, 14, 2484

by

Joshua Letizia

¹,

Vijaya Chalivendra

^1,*

and

Dapeng Li

²

¹

Department of Mechanical Engineering, University of Massachusetts, Dartmouth, MA 02747, USA

²

Department of Bioengineering, University of Massachusetts, Dartmouth, MA 02747, USA

^*

Author to whom correspondence should be addressed.

Polymers 2022, 14(15), 3195; https://doi.org/10.3390/polym14153195

Submission received: 7 July 2022 / Accepted: 25 July 2022 / Published: 5 August 2022

Download

Browse Figure

Versions Notes

In the original publication [1], there was a mistake in Figure 12 as published. Figure 8 was accidentally inserted instead of Figure 12 during the proofreading stage. We have modified the figure caption by deleting the following part “Zoomed in 0° filaments are in orange; 90° filaments are in red” because it is not necessary and adds confusion. Also, we added “of 0° filament” at the end of last line of the figure caption for clarity. The corrected Figure 12 and legend appears below. The authors apologize for any inconvenience caused and state that the scientific conclusions are unaffected. This correction was approved by the Academic Editor. The original publication has also been updated.

Reference

Letizia, J.; Chalivendra, V.; Li, D. Effect of Shear Angle and Printing Orientation on Shear Constitutive Response of Additively Manufactured Acrylonitrile Butadiene Styrene. Polymers 2022, 14, 2484. [Google Scholar] [CrossRef] [PubMed]

Figure 12. Scanning electron microscope snapshot of shear zone in the 0°/90° orientation with a 20.83° shear angle (left). Close up of shear zone of 0° filament (right).

Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

© 2022 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (https://creativecommons.org/licenses/by/4.0/).

Share and Cite

MDPI and ACS Style

Letizia, J.; Chalivendra, V.; Li, D. Correction: Chalivendra et al. Effect of Shear Angle and Printing Orientation on Shear Constitutive Response of Additively Manufactured Acrylonitrile Butadiene Styrene. Polymers 2022, 14, 2484. Polymers 2022, 14, 3195. https://doi.org/10.3390/polym14153195

AMA Style

Letizia J, Chalivendra V, Li D. Correction: Chalivendra et al. Effect of Shear Angle and Printing Orientation on Shear Constitutive Response of Additively Manufactured Acrylonitrile Butadiene Styrene. Polymers 2022, 14, 2484. Polymers. 2022; 14(15):3195. https://doi.org/10.3390/polym14153195

Chicago/Turabian Style

Letizia, Joshua, Vijaya Chalivendra, and Dapeng Li. 2022. "Correction: Chalivendra et al. Effect of Shear Angle and Printing Orientation on Shear Constitutive Response of Additively Manufactured Acrylonitrile Butadiene Styrene. Polymers 2022, 14, 2484" Polymers 14, no. 15: 3195. https://doi.org/10.3390/polym14153195

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Menu

Correction: Chalivendra et al. Effect of Shear Angle and Printing Orientation on Shear Constitutive Response of Additively Manufactured Acrylonitrile Butadiene Styrene. Polymers 2022, 14, 2484

Reference

Share and Cite

Article Metrics

Article Access Statistics

Further Information

Guidelines

MDPI Initiatives

Follow MDPI