Next Article in Journal
Power Factor Adaptive DPWM Control Strategy for T-Type Three-Level Inverters
Next Article in Special Issue
Novel Adaptive Super-Twisting Sliding Mode Observer for the Control of the PMSM in the Centrifugal Compressors of Hydrogen Fuel Cells
Previous Article in Journal
A Transformer-Based Hybrid Neural Network Integrating Multiresolution Turbulence Intensity and Independent Modeling of Multiple Meteorological Features for Wind Speed Forecasting
Previous Article in Special Issue
General Principles of Combinations of Stator Poles and Rotor Teeth for Conventional Flux-Switching Brushless Machines with Prime Phase Numbers
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Experimental Validation of Manufacturable Edgewise Winding Solutions Considering Parallel Slot and Parallel Tooth Stator Structures

PEMC Research Institute, Jubilee Campus, University of Nottingham, Nottingham NG7 2GT, UK
*
Author to whom correspondence should be addressed.
Energies 2025, 18(17), 4572; https://doi.org/10.3390/en18174572
Submission received: 4 July 2025 / Revised: 8 August 2025 / Accepted: 9 August 2025 / Published: 28 August 2025
(This article belongs to the Special Issue Designs and Control of Electrical Machines and Drives)

Abstract

High-power-density electric machines play a key role in decarbonising transportation technologies. A critical component of the movement towards high-performance machines is the structure and manufacture of the windings, as this is the dominant source of machine loss. Manufacturing time is important to the effectiveness of the production line, with equivalent importance to the electromagnetic and thermal characteristics. Edgewise windings are increasingly considered to have high potential to be quickly and automatically manufactured. However, they are rarely studied considering all the aspects, these being electromagnetic, thermal, and manufacturing characteristics. This paper will experimentally assess the performance of edgewise machines compared to a stranded winding machine, covering all the aforementioned aspects. Two edgewise winding types are considered, parallel slot and parallel tooth. Firstly, a baseline 11 kW stranded winding machine will be introduced, then two edgewise type machines are proposed to be compared to the baseline machine. These comparisons will initially be made based on simulated torque and thermal performance, then the manufacturing time and quality are assessed for each of the coil structures, showing the achievable time reduction by using edgewise coil structures. Motorettes are used to validate thermal performance of the structures, which are used to calibrate simulation models and evaluate the performance of a full machine equivalent model. Under the thermal limit condition, it is shown that the edgewise parallel tooth windings can achieve a torque increase of 27.8% compared to stranded and 24% compared to edgewise parallel slot.

1. Introduction

The demand for high-power-density machines is increasing to meet the needs of transportation electrification and to achieve the 2050 zero carbon goal. Due to the dominance of winding loss, technology demand forecasts predict that increased production will be required across all operating regions, so enabling scalable production is essential [1]. Winding faults, particularly conductor faults, are a major source of machine failure [2]. Improving manufacturing quality is necessary for automotive production [3], as defects impact electrical, thermal, and mechanical performance, leading to increased losses, reduced lifetime, and machine failure [4,5].

1.1. Electromagnetic Characteristics

Different types of windings are available, such as stranded, hairpin, and edgewise. Hairpin conductors have high fill factors but suffer from high AC losses, whereas litz wire has good high-frequency performance but is complex to manufacture. These are not explored in depth at the current stage of research [6]. Edgewise conductors are rectangular bar conductors with large cross-sectional areas (CSA) and aspect ratios.
Stranded conductors typically achieve 0.4–0.5 slot fill due to poor geometric compatibility, while edgewise conductors reach up to 0.7 due to their rectangular CSA [7,8,9,10]. Edgewise windings also have shorter end windings, leading to lower resistance and, thus, lower DC loss [9]. At room temperature, stranded coil structures have been shown to have per unit DC resistance 2.3× higher than an edgewise coil equivalent [11].
On the other side, AC losses, while generally lower in small conductors, also suffer from proximity losses and vary with manufacturing precision. Stranded windings have high variability, in both build method and the resulting coils, while edgewise windings have higher manufacturing precision. However, edgewise windings experience skin effect losses due to high eddy current circulation, which can be reduced by optimising the aspect ratio [7,9,12,13]. Additionally, higher AC copper losses occur at the slot opening due to the large conductor volume and high leakage flux, this can be overcome with a higher number of conductors per slot and by reducing conductor size [14].
Due to differing loss characteristics, the AC/DC loss ratio varies considerably between the winding types. Stranded windings have AC/DC loss ratios ranging from 1.8 to 4 at 1.5 kHz operating frequency [15,16]. However, manufacturing variation can substantially affect this ratio. In one study, stranded coils showed AC/DC loss ratio from 3.5 to 6.3 at 1 kHz purely from manufacturing variation, leading to the rejection of one-third of the produced coils [17].
Conversely, edgewise windings, while offering lower DC losses, experience higher AC copper losses, resulting in an AC/DC loss ratio that increases rapidly with frequency [18]. Small edgewise conductors have been shown to have an AC/DC loss ratio of 4 at 1 kHz, whereas large edgewise conductors can have AC/DC loss ratios of up to 20 at the same frequency [18].
In general, AC copper losses represent a smaller proportion of total losses in stranded windings compared to edgewise. In one comparative case, AC copper losses accounted for 55.5% of the total losses in a stranded winding, whereas the edgewise equivalent had 76.5% of the total loss attributed to AC losses [11]. These impacts are summarised in Table 1.
With stringent design, considering conductor aspect ratio and slot position, the AC/DC loss ratio of edgewise windings can be reduced to be comparable to stranded windings. However, this typically requires large numbers of conductors and complex manufacturing [19,20].

1.2. Thermal Characteristics

Edgewise conductors also offer high thermal conductivity due to favourable surface-area-to-volume ratios, high surface contact area, and high effective slot thermal conductivity from high fill factor. These characteristics make them ideal for thermally constrained, or cost-sensitive applications, as they can reduce the cooling requirements.
Flat-wire structures have demonstrated equivalent slot thermal conductivities of 1.4–2.83 W/mK for standard fill factors [20,21,22] and up to 5.41 W/mK in compact, high-fill designs [21,23]. In comparison, a typical stranded winding ranges from 0.25–0.96 W/mK [21,24,25], with highly compact designs achieving up to 2.1 W/mK [21].
This improved thermal conductivity in edgewise windings allows for the use of lower conductor volume with increased thermal conductivity, reduced requirements on insulation thermal limits, or extended lifespans due to lower operating temperatures [26].
Table 1. Electromagnetic performance parameters for conductor types.
Table 1. Electromagnetic performance parameters for conductor types.
ParameterWinding TypeRef.
StrandedEdgewise
Fill factor0.45–0.550.7–0.75[7,8,27]
DC lossHighLow[12,28]
AC lossMediumMedium-High[29]

1.3. Mechancial and Manufacturing Characteristics

Mechanically, stranded wires face constraints like limited end winding bend radius and susceptibility to NVH-induced degradation, such as insulation sparking [30,31,32]. Edgewise conductors, are more robust and consistent with lower manufacturing variability, but are sensitive to bending and welding-induced strain, particularly from the high aspect ratio of the conductor [33,34,35]. Mechanical stress in edgewise designs can impact electrical conductivity, insulation, thermal resistance, and overall reliability and mean failure time [36].
Manufacturing processes have inherent tolerances, with manual methods showing higher variability that increases losses, faults, and labour costs [37]. Manual stranded winding is often required for complex structures [7,30], but causes performance loss due to placement sensitivity, leading to issues like partial discharge and insulation failure. Stranded windings can be made via automated needle, flyer, or linear winding techniques for concentrated coils. For distributed coils, insert methods can be implemented where the coil is wound onto an insertion tool in the slot, which is later removed. This technique is used in vehicles like the BMW i-series and Tesla Model S [38]. However, there are still challenges such as high wire stress, position variability, long end windings, and limited fill factor [34,39].
Edgewise windings allow more predictable, automated manufacturing due to the large CSA [40]. Further, edgewise windings offer better robustness and scalability but have higher upfront costs and design constraints, such as slot structure and coil dimensions [35]. Typically, it is necessary to compromise electromagnetic performance to practically manufacture the winding; for example, the slot opening must be wide enough to fit the coil. Edgewise windings have higher initial investment due to tooling but are becoming more common [41]. These conclusions are summarised in Table 2.
The paper will provide a comprehensive view of both stranded and edgewise winding types, as well as experimentally validating the performance. The paper structure is as follows: Section 2 presents the baseline machine performance and simulation analysis; Section 3 shows the motorette manufacturing and experimental results. Finally, Section 4 concludes the research. The contribution of the paper is the development of a highly manufacturable edgewise winding structure without significant performance impact.

2. Simulation Analysis

2.1. Base Machine

The 11 kW base machine parameters used are shown in Table 3, the machine cross-section is shown in Figure 1, and the winding structures considered are outlined in Table 4. For each winding design, the narrowest part of the tooth, where the flux density is highest, is kept constant. The machine is cooled using a housing water jacket with 3 L/min glycol–water coolant.

2.2. Proposed Edgewise Windings Machine

Manufacturing factors such as reproducibility and ease of assembly are critical to design procedures. For edgewise windings, the slot–tooth geometry plays a key role, and so two types of edgewise windings are investigated, shown in Figure 2. The parallel slot (PS) stator has a constant slot width, leading to high fill factor, with trapezoidal teeth, leading to variable coil dimensions and tapered end windings, especially in multi-layer coils. In contrast, the parallel tooth (PT) structure features a fixed tooth width and trapezoidal slots, producing uniform coil dimensions across turns and slot depths. The change in these coil structures is shown in Figure 2. This uniformity simplifies manufacturing and reduces potential issues, ensuring consistent coil and end winding volumes throughout the machine.
A simulation case study has been undertaken to assess the impact of edgewise windings in PS and PT stators on electromagnetic and thermal characteristics [42]. The differences in the calculation method are illustrated in Figure 3 and the resultant end winding lengths and applied build factors are shown in Table 4.
The fill factor for the PT winding is reduced due to the change in slot width with stator radial depth, see Figure 2b. Structures where the conductor dimension changes with each turn to achieve the maximum fill factor are available, but these are challenging to manufacture, requiring additive manufacturing techniques or an intensively modular coil structure.

2.3. Simulation Results

The torque performance of each winding structure is evaluated using a current loading factor, which accounts for variations in conductor dimensions, current, and number of turns. Torque is proportional to volume and magnetic and electrical loading. Between all designs, the dimensions, the rotor, and the air gap length are kept the same to ensure the volume and magnetic loading are constant and only electrical loading is varying. Further, the numbers of slots and phases are kept constant between designs, so the change in current loading is represented by the number of turns and the current, and the change in current loading factor serves as a torque indicator [43]. This is shown in Equations (1)–(3). For Equation (1), T, V, B, and A represent torque, volume, magnetic loading, and electrical loading, respectively. For Equations (2) and (3), N p h , m, I, and D g represent the number of turns per phase, number of phases, current, and air gap diameter, respectively.
T   V B A
A = 2 m N p h I π D g
C u r r e n t   l o a d i n g   f a c t o r ,   A k = N p h I
Three simulated operating points are considered, a fixed current loading value, the thermal limit condition, and a fixed torque-speed operating point

2.3.1. Fixed Current Loading Operating Point

A value of 5000 Amp-turns is chosen to evaluate the machine performance with different winding types, while all structures remain within the thermal limit of 180 °C. Amp-turns means the current times the turns, which will provide fair comparison, as discussed in the previous section. Figure 4 shows that both edgewise solutions provide more torque for fixed current loading factor. The edgewise PT winding delivers 42.9 Nm, followed by edgewise PS with 42.1 Nm, then stranded with 42.05 Nm. The edgewise PT has a 0.8 Nm increase in torque, this is attributed to a 2.5% increase in air gap flux density.

2.3.2. Thermal Limit Condition

The structures are also assessed when current loaded to reach the thermal limit (180 °C), as shown in Table 5. The thermal limit condition is achieved by iteratively solving finite element electromagnetic and Lumped Parameter Thermal Network (LPTN) simulations until convergence is achieved. The results in Table 5 indicate that the edgewise PT winding has the highest current loading, which reflects the increase in maximum current due to the change in loss density. Consequently, this structure delivers the most torque. The edgewise PS and stranded structure have equal currents for the thermal limit. However, edgewise PS delivers higher torque, resulting in higher efficiency. Further, the edgewise PS structure has a lower current than the edgewise PT structure and lower phase resistance than the stranded structure, both of which act to reduce DC loss.

2.3.3. Fixed Torque-Speed Operating Point

This section evaluates the performance while torque and speed are kept constant for the machines with different winding types. At a fixed operating point of 2500 RPM and 60 Nm (Table 6), the stranded winding needs the highest current loading and, consequently, DC losses to meet the torque requirement. The edgewise PS structure needs a 1 A increase in current to achieve the torque requirement compared to edgewise PT, reflected by the reduction in torque constant. The edgewise PT winding has the lowest DC losses, however, has higher iron losses due to the stator, which has a lower steel area for the same flux, leading to higher flux density compared to edgewise PS and higher iron losses. Edgewise PT has the highest efficiency due to DC loss dominance at the operating point.
At 2500 RPM, the operating frequency is 166.67 Hz, so the stranded winding avoids AC loss challenges from skin depth, but the AC copper loss remains high due to proximity loss. Proximity losses are generated when exposed to external magnetic fields from parallel strands [15], so this results from high flux density, reflected in the iron loss, as well as the large number of conductors. The stranded iron loss indicates an increase in flux density compared to edgewise PS, attributed to the increase in current. Stranded windings can use partially closed slot openings to reduce air gap flux variation and improve torque ripple, but this advantage does not match the performance of prefabricated conductors. Edgewise windings require wider slots to fit larger coils, resulting in a slot opening that is wider than ideal.

3. Experimental Validation

This section validates simulation results with experimental testing on motorettes. An overview of the test conditions and motorette design are provided, followed by experimental results for the coil manufacturing process, and thermal performance with DC current. DC current is used to evaluate the cooling performance between different segments and the values of DC losses can be accurately quantified during the tests.

3.1. Motorettes

Motorettes with stranded windings, and edgewise windings in PS and PT stators, are manufactured in six-slot sections, representing ¼ of the machine. The structure ensures realistic tangential heat generation; additionally, using this number of slots allows for incorporation of end winding connections. For simplicity, the stator core is aluminium and iron loss is not considered at this stage [44]. Motorettes are chosen over a full machine to reduce costs and allow for multiple prototype variants at reduced build time [45].
Each motorette is equipped with 15 thermocouples. The critical in-slot thermocouple arrangement is shown in Figure 5. Thermocouple 1 (TC1) measures the hotspot temperature, while TC2 and TC3 capture temperature distribution within the slot. Thermocouples also monitor the end windings, and the same TC1–3 layout is applied through different slots and axial lengths.

3.2. Manufacturing Process Analysis

The stranded coils are manually wound for the experimental prototypes. In contrast, the manufacturing of edgewise coils reduces each layer to a series of turn angles and length projections. This process is completed using the LJU Bending Winding System (BWS), which forms part of the DER winding line at the PEMC Research Institute at the University of Nottingham. This system is shown in Figure 6, depicting the straightened wire being fed onto the central bending mandrel.
During manufacturing, the wire is fed through the counter bearing to the specified length and the turn angle is fabricated by pushing the fed-through wire around the bending mandrel. This process of feeding the wire through and creating the turn angles around the bending mandrel is repeated layer-by-layer until the full coil structure is realised. At this point, the coil is passed to the linear handling by the bobbin mandrel and fed through to the belt outlet where the wire is cut.
Production times for each prototype are measured to assess manufacturing efficiency. Using motorette prototypes that are easy to produce is key as this facilitates the testing and validation of manufacturing processes, assembly, and parameter calibration for simulations. Further, prototyping multiple variants helps reduce material and consumption and labour requirements, improving efficiency in early-stage testing.
For mass production of full-sized machines, some adjustments would be necessary. While the fundamental manufacturing and assembly remains consistent, the stranded winding motorettes would likely be produced using automated or semi-automated techniques such as needle or flyer winding. However, the BWS or similar systems would still be employed for producing edgewise coils for mass manufacturing. Additionally, the coil assembly process would become more complex as the motorettes do not include the full, per-phase end winding layout; instead, these are modified to form continuous windings for DC excitation.
Producing edgewise coils in PS stators is more complex and time-consuming due to variable end turn lengths and angles, resulting in increased tuning for tolerance for material spring-back [44]. The variation in dimensions is shown in Figure 2. In contrast, PT stators allow uniform turn dimensions, reducing design and manufacturing complexity. The edgewise coil structures are shown in Figure 7.
The “Initial coil” time describes the time taken to manufacture the first coil from the theoretical dimensions, and the “Subsequent coils” time reflects the average time taken to produce one additional coil with the same dimensions. Figure 8 shows that the manually wound stranded coils take substantially longer to manufacture, both for the initial coil and subsequent coils. Compared to edgewise PS, the more time-consuming edgewise structure, the stranded coils have 2.6 times higher initial coil time and 6.3 times higher subsequent coil time. Further, it is shown that the edgewise PT coils require 91% less initial design time and 80% less build time per coil than PS coils, due to fewer variable design points and easier tolerance management. The edgewise PS windings face construction challenges from cumulative tolerance and error, and this is reflected in the fact that the initial and subsequent coil build times for edgewise PS are higher than the stranded coils, which are manually wound. The continued gap between PT and PS per coil duplicate illustrates the challenges in accounting for cumulative error. It is shown that for situations where minimising manufacturing time and expense is a priority, the use of edgewise coils in the PT stator can substantially reduce the overall coil manufacturing time.

3.3. Thermal Analysis

The DC resistance and the variation between the coils in the sample set is assessed, and the measurements are given in Table 7. The original calculation overestimates the resistance by around 2% for the edgewise coils compared to a 24% underestimation for the stranded coil. The stranded coils calculation is an underestimation as they are required to give substantial clearance for end winding bending and the bend radii used in practice are not accurately known. Further, the overlap between conductors results in substantial variations in end winding length for stranded layouts. For the edgewise coils, the calculation method accounts analytically for the end winding bend radii that occur during manufacturing. In this case, the allowance for bend radius is slightly higher than the measured result, resulting in a smaller resistance. The measured data shows that edgewise PT coils have lower DC resistance, which is expected due to lower path length. There is variation between different sets of coils, for example, 0.6% is shown for PT coils and 6.5% for PS coils, reflecting PT coils having better manufacturing consistency and alignment with simulation.
This section evaluates the thermal performance of windings with DC currents, focusing on temperature rise and distribution. The tests use a housing water jacket with controlled coolant flow and monitored temperature. DC current is supplied until reaching thermal equilibrium, which is defined as less than 1 °C temperature change over 10 min. The process is repeated at increasing currents until insulation limits are reached. Results are used to calibrate simulations and support conclusions. The test rig is shown in Figure 9.
Table 8 presents the temperatures measured at thermocouple nodes under maximum steady-state current loading, representing the thermal limit without exceeding 180 °C. If the temperature exceeds this limit, the rig is shut down to prevent damage. Consequently, the current is increased in set intervals, and the highest interval where the system could reach thermal steady state without exceeding 180 °C is used for comparison.
For the stranded segment, the difference between the maximum and minimum temperatures (temperature variation) within the slot is 74.4 °C at a current loading of 3685 Amp-turns, representing a 42% temperature difference. This is the largest thermal variation among the tested segments. This is partly due to the lower copper-to-insulation ratio in the round wire, as insulation has much lower thermal conductivity, reducing the overall heat transfer. Additionally, the fill factor is lower, and manufacturing variability leads to uneven conductor placement and greater temperature variation [46]. The stranded segment also shows lower temperatures in the active region at its thermal limit due to lower axial thermal conductivity compared to edgewise. As a result, different axial positions reach the insulation thermal limit at varying rates, restricting the maximum current loading factor to 3685 Amp-turns for a 180 °C thermal limit.
For the same thermal limit, 4896 Amp-turns can be applied to edgewise windings. The edgewise PS structure showed a maximum slot temperature variation of 30.7 °C at 4896 Amp-turns, equivalent to an 18.2% difference in temperature across the slot distribution, meaning that the maximum and minimum temperatures are closer to the average temperature. The reduction in variation compared to the stranded winding is due to a higher copper-to-insulation ratio, which enhances radial and tangential thermal conductivity. Edgewise PS also shows higher temperatures at the centre of the winding, reflecting improved axial thermal conductivity.
The edgewise PT structure has maximum slot temperature variation of 35.4 °C at 4896 Amp-turns, which is a 20.8% temperature shift in the slot. Although it has the same copper-to-insulation ratio as the PS structure, geometric factors like reduced contact area and more resin restrict thermal conductivity and cause greater temperature differences within the slot. The steady-state temperature rise per current loading factor operating point is shown in Figure 10.
Overall, the edgewise segments achieve higher current loading factor than the stranded segment. Although the stranded winding has a higher number of turns per phase, the small CSA limits the current capacity due to the temperature rise. The stranded winding reaches a maximum current loading of 3685 Amp-turns, with a temperature rise of 110 °C. In comparison, edgewise windings at similar current loadings have 35 °C and 39 °C temperature increases for PS and PT, respectively. For equal temperature rise of 115 °C, the stranded winding reaches a current loading factor of 3413 Amp-turns, compared to 4570 Amp-turns for edgewise PS and 4861 Amp-turns for edgewise PT, representing an increase in current loading factor of 1157 Amp-turns and 1448 Amp-turns, respectively, compared to the stranded control motorette, corresponding to an increase of 25.3% and 42.4%. At the same current loading factor of 4608 Amp-turns for the edgewise windings with PS and PT structures, the edgewise PT windings show a 13.8 °C lower operating temperature than the PS winding, equal to a current of 51 A in the edgewise structures.

3.4. Comparison

From a manufacturing perspective, the edgewise winding structures are quicker to manufacture, with low variation in performance compared to stranded windings, which are manually wound. This leads to an increase in manufacturing efficiency and costs, with a per-coil manufacturing time reduction of 84% moving from stranded to the edgewise PS structure. Further, by considering the stator slot–tooth geometry, the manufacturing complexity of the edgewise structures can be further reduced by 80% by implementing PT stator structures to simplify the geometry of edgewise coils. This further reduces manufacturing time and complexity, resulting in reduced costs, as well as increased precision in the manufactured coils.
From an electromagnetic perspective, this increase in precision results in more predictable DC resistance characteristics, with 6.5% variation in DC resistance for edgewise PS and 0.6% variation for edgewise PT. This leads to increased confidence in DC loss performance and more predictable electromagnetic performance for edgewise PT.
The experimental validation of losses and thermal performance is used to determine key performance parameters at the thermal limit. The equivalent slot thermal conductivity for each structure is determined through calibrating an equivalent LPTN. Simulations are completed with the updated thermal conductivity and resistance parameters. These results are summarised in Table 9.
For the current experimental set up, in which the in-slot gaps are filled with resin and the cooling is provided by a housing water jacket, the equivalent thermal conductivity of each winding structure is evaluated. The stranded winding has a moderate improvement compared to the simulation, at 0.63 W/mK. In comparison, the edgewise structures demonstrate significantly higher values than the stranded winding due to increased copper volume and a higher copper-to-insulation ratio. However, the edgewise PT structure shows a reduction in equivalent thermal conductivity relative to edgewise PS, which is due to the larger volume of resin required to fill the in-slot gaps, reducing the overall thermal conductivity.
As the edgewise windings have higher equivalent thermal conductivity, the maximum current loading achievable while remaining under the thermal limit is higher than the stranded windings. As with the pre-experimental simulations, the stranded structure achieves slightly higher current density despite having slightly lower current due to the change in turn CSA. This impacts the loss density in the slot, as is also seen with the change in current. There is a relatively small change from stranded to edgewise PS, this is due to higher slot volume for the stranded layout, which reduces the in-slot loss density, so despite the lower thermal conductivity, the dissipation area is higher, resulting in higher achievable current density. This change is further highlighted by the large increase in potential current for the edgewise PT layout. Despite the thermal conductivity being slightly lower than edgewise PS, the slot area is larger and, consequently, the maximum allowable current increases considerably, a 30% increase from the stranded winding. Consequently, the achievable torque is higher for the edgewise PT winding, 27.8% higher than stranded and 24% higher than edgewise PS.
Therefore, it is concluded that the implementation of edgewise PT winding structures can increase the manufacturability beyond that of a conventional stranded winding but also improve manufacturability compared to edgewise PS structures. Further, this edgewise PT structure allows for increased current loading while maintaining the same thermal limit, leading to higher torque production in a full machine equivalent.

4. Conclusions

High-performance electrical machines are at the core of the transportation electrification sectors to achieve the 2050 zero carbon target. Windings are key components of electrical machines, including stranded, hairpin, and edgewise windings, but are rarely reported on in terms of all the multidomain aspects. This paper has assessed edgewise windings with both PS and PT structures, from electromagnetic, thermal, and manufacturing perspectives, in comparison to stranded windings. It has been shown that with similar current loading factors, the decrease in DC losses is 53% for the edgewise windings compared to the stranded ones. For a comparable temperature rise of around 110 °C, the increase in current for the edgewise windings compared to the stranded windings results in a 50% increase in torque production when applied to the full machine. With motorettes manufactured and experimentally tested, it is shown that edgewise PS windings reduce manufacturing time per coil by 85% compared to stranded windings, and edgewise PT structures can reduce the per coil manufacturing time by a further 80%, with improved manufacturing consistency and repeatability compared to both stranded windings and edgewise PS windings. Further, the average operating temperature at the highest load operating point is 13.8 °C lower for an edgewise parallel tooth than the parallel slot equivalent, however, it has 1.9 °C higher hot spot temperatures. Calibrated simulation results show that by operating at the thermal limit condition, edgewise parallel tooth windings can achieve a torque increase of 27.8% compared to stranded windings and 24% compared to the edgewise parallel slot. Overall, this leads to a recommendation for the usage of edgewise PT coil structures for manufacturability and thermal performance.
To further improve the thermal performance, the unused slot space in the PT design offers potential for improved cooling and higher current loading, which will be explored in future work.

Author Contributions

Writing—original draft, E.G.; writing—review and editing, A.W. and F.Z.; review and editing, G.V. and C.G. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by ABB.

Data Availability Statement

The original contributions presented in this study are included in the article. Further inquiries can be directed to the corresponding author.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. APC UK. Electrical Machines. In Technology Roadmap; APC UK: Warwick, UK, 2020. [Google Scholar]
  2. Alewine, K.; Chen, W. A review of electrical winding failures in wind turbine generators. IEEE Electr. Insul. Mag. 2012, 28, 8–13. [Google Scholar] [CrossRef]
  3. Farnsworth, M.; Tiwari, D.; Zhang, Z.; Jewell, G.W.; Tiwari, A. Augmented classification for electrical coil winding defects. Int. J. Adv. Manuf. Technol. 2022, 119, 6949–6965. [Google Scholar] [CrossRef]
  4. Singh, G.; Sundaram, K. Manufacturing deformation impact on the performance of electrical generator for the wind turbine application. Wind Eng. 2021, 45, 1193–1205. [Google Scholar] [CrossRef]
  5. Zhang, H.; Zhang, M.; Wang, X. Fracture failure analysis of insulation with initial crack defect for stator end-winding in induction motor by using magnetic-structural coupling model. Eng. Fail. Anal. 2023, 149, 107239. [Google Scholar] [CrossRef]
  6. George, L.; Walker, A.; Zhang, F.; Vakil, G.; Gerada, C. Comparison of V-shaped IPM Machines Winding Topologies for Heavy-duty EV Applications. In Proceedings of the 2023 IEEE International Conference on Electrical Systems for Aircraft, Railway, Ship Propulsion and Road Vehicles & International Transportation Electrification Conference (ESARS-ITEC), Venice, Italy, 29–31 March 2023; pp. 1–7. [Google Scholar] [CrossRef]
  7. Selema, A.; Ibrahim, M.N.; Sergeant, P. Development of Novel Semi-Stranded Windings for High Speed Electrical Machines Enabled by Additive Manufacturing. Appl. Sci. 2023, 13, 1653. [Google Scholar] [CrossRef]
  8. Schiefer, M.; Doppelbauer, M. Indirect slot cooling for high-power-density machines with concentrated winding. In Proceedings of the 2015 IEEE International Electric Machines & Drives Conference (IEMDC), Coeur d’Alene, ID, USA, 10–13 May 2015; pp. 1820–1825. [Google Scholar] [CrossRef]
  9. Okada, T.; Matsumori, H.; Kosaka, T.; Matsui, N. Hybrid Excitation Flux Switching Motor with Permanent Magnet Placed at Middle of Field Coil Slots Employing High Filling Factor Windings. In Proceedings of the 2018 IEEE Energy Conversion Congress and Exposition (ECCE), Portland, OR, USA, 23–27 September 2018; pp. 4268–4274. [Google Scholar] [CrossRef]
  10. Tom, L.; Khowja, M.R.; Ramanathan, R.K.; Vakil, G.; Gerada, C.; Benarous, M. Investigation of Slot Shape and Associated Winding Configuration for Aerospace Actuator Motor. In Proceedings of the 2023 IEEE International Electric Machines & Drives Conference (IEMDC), San Francisco, CA, USA, 15–18 May 2023; pp. 1–7. [Google Scholar] [CrossRef]
  11. Selema, A.; Gulec, M.; Ibrahim, M.N.; Sprangers, R.; Sergeant, P. Selection of Magnet Wire Topologies With Reduced AC Losses for the Windings of Electric Drivetrains. IEEE Access 2022, 10, 121531–121546. [Google Scholar] [CrossRef]
  12. REO. REO Edge-Winding. Available online: https://www.reo.co.uk/reo-edge-winding/ (accessed on 25 May 2022).
  13. Rocca, A.L.; Zou, T.; Moslemin, M.; Gerada, D.; Gerada, C.; Cairns, A. Thermal Modelling of a Liquid Cooled Traction Machine with 8-layer Hairpin Windings. In Proceedings of the IECON 2021—47th Annual Conference of the IEEE Industrial Electronics Society, Toronto, ON, Canada, 13–16 October 2021; pp. 1–6. [Google Scholar] [CrossRef]
  14. Yan, Y.; Mao, C.; Li, C.; Ren, H. Analysis and Optimization of the Winding Loss of Flat-Wire Motors. Electronics 2024, 13, 3115. [Google Scholar] [CrossRef]
  15. Bardalai, A.; Gerada, D.; Golovanov, D.; Xu, Z.; Zhang, X.; Li, J.; Zhang, H.; Gerada, C. Reduction of Winding AC Losses by Accurate Conductor Placement in High Frequency Electrical Machines. IEEE Trans. Ind. Appl. 2020, 56, 183–193. [Google Scholar] [CrossRef]
  16. Bardalai, A.; Gerada, D.; Zou, T.; Degano, M.; Zhang, C.; Gerada, C. Comparison of AC Losses in the Winding of Electrical Machines with Fixed Strands Positions, Fixed Conductor Shapes and Random Winding. Energies 2022, 15, 5701. [Google Scholar] [CrossRef]
  17. Mellor, P.; Hoole, J.; Simpson, N. Computationally efficient prediction of statistical variance in the AC losses of multi-stranded windings. In Proceedings of the 2021 IEEE Energy Conversion Congress and Exposition (ECCE), Vancouver, BC, Canada, 10–14 October 2021; pp. 3887–3894. [Google Scholar] [CrossRef]
  18. Du, G.; Ye, W.; Zhang, Y.; Wang, L.; Pu, T.; Huang, N. Comprehensive Analysis of the AC Copper Loss for High Speed PM Machine With Form-Wound Windings. IEEE Access 2022, 10, 9036–9047. [Google Scholar] [CrossRef]
  19. Yu, W.; Hua, W.; Wang, P.; Xia, W. Comparative Analysis of AC Loss with Round Copper Wire and Flat Copper Wire of High-Speed Stator PM Flux-Switching Machine: Comparative Analysis of AC Loss of HS-SPMFS Machine. In Proceedings of the 2021 IEEE 4th International Electrical and Energy Conference (CIEEC), Wuhan, China, 28–30 May 2021; pp. 1–5. [Google Scholar] [CrossRef]
  20. Zhu, S.; Paciura, K.; Barden, R. Application of Flat Rectangular Wire Concentrated Winding for AC loss Reduction in Electrical Machines. In Proceedings of the 2021 IEEE Energy Conversion Congress and Exposition (ECCE), Vancouver, BC, Canada, 10–14 October 2021; pp. 4619–4623. [Google Scholar] [CrossRef]
  21. Ayat, S.; Wrobel, R.; Goss, J.; Drury, D. Estimation of equivalent thermal conductivity for impregnated electrical windings formed from profiled rectangular conductors. In Proceedings of the 8th IET International Conference on Power Electronics, Machines and Drives (PEMD 2016), Glasgow, UK, 19–21 April 2016; pp. 1–6. [Google Scholar] [CrossRef]
  22. Shen, Q.; Xi, X.; Zhu, H.; An, P.; Zeng, Y.; Zhong, Y.; He, L. Design of Spray Cooling System for Yasa Afpm Flat Wire Winding Motors. 2025. Available online: https://ssrn.com/abstract=5364071 (accessed on 15 July 2025).
  23. Ahmad, Z.; Wrobel, R.; Werner, T.C.; Odhano, S.; Pickert, V. An Accurate Experimental Approach for Deriving Equivalent Thermal Conductivity of Impregnated Electrical Windings. In Proceedings of the 2023 IEEE Energy Conversion Congress and Exposition (ECCE), Nashville, TN, USA, 29 October–2 November 2023; pp. 3810–3817. [Google Scholar] [CrossRef]
  24. Verbeek, N.; Favresse, S.; Baudart, F.; Dehez, B. Estimation of Equivalent Thermal Conductivity of PCB Airgap Windings. In Proceedings of the 2022 International Conference on Electrical Machines (ICEM), Valencia, Spain, 5–8 September 2022; pp. 1362–1368. [Google Scholar] [CrossRef]
  25. Tang, Z.; Wang, Y.; Yu, F.Y.; Shi, D.; Shen, J.X. Estimation of Equivalent Thermal Conductivity for Electric Machine Windings Using Conformal Mapping Method. IEEE Trans. Transp. Electrif. 2025, 11, 7662–7672. [Google Scholar] [CrossRef]
  26. Kampen, D. Future Winding for Next Power Electronic Generation. In Proceedings of the PCIM Europe 2018; International Exhibition and Conference for Power Electronics, Intelligent Motion, Renewable Energy and Energy Management, Nuremberg, Germany, 5–7 June 2018. [Google Scholar]
  27. Wrobel, R.; Ayat, S.; Baker, J.L. Analytical methods for estimating equivalent thermal conductivity in impregnated electrical windings formed using Litz wire. In Proceedings of the 2017 IEEE International Electric Machines and Drives Conference (IEMDC), Miami, FL, USA, 21–24 May 2017; pp. 1–8. [Google Scholar] [CrossRef]
  28. Okada, T.; Matsumori, H.; Kosaka, T.; Matsui, N. Hybrid excitation flux switching motor with permanent magnet placed at middle of field coil slots and high filling factor windings. CES Trans. Electr. Mach. Syst. 2019, 3, 248–258. [Google Scholar] [CrossRef]
  29. Väisänen, V.; Hiltunen, J.; Nerg, J.; Silventoinen, P. AC resistance calculation methods and practical design considerations when using litz wire. In Proceedings of the IECON 2013—39th Annual Conference of the IEEE Industrial Electronics Society, Vienna, Austria, 10–13 November 2013; pp. 368–375. [Google Scholar] [CrossRef]
  30. Arumugam, P.; Hamiti, T.; Gerada, C. Fault tolerant winding design—A compromise between losses and fault tolerant capability. In Proceedings of the 2012 XXth International Conference on Electrical Machines, Marseille, France, 2–5 September 2012; pp. 2559–2565. [Google Scholar] [CrossRef]
  31. Stone, G.C.; Wu, R. Examples of stator winding insulation deterioration in new generators. In Proceedings of the 2009 IEEE 9th International Conference on the Properties and Applications of Dielectric Materials, Harbin, China, 19–23 July 2009; pp. 180–185. [Google Scholar] [CrossRef]
  32. Sedding, H.G.; Chan, C.; Sasic, M.; Stone, G.C. Assessment of Stator Winding Insulation Condition Based on Absolute Partial Discharge Magnitude. In Proceedings of the 2023 INSUCON—14th International Electrical Insulation Conference (INSUCON), Birmingham, UK, 18–20 April 2023; pp. 19–23. [Google Scholar]
  33. Al-Timimy, A.; Giangrande, P.; Degano, M.; Galea, M.; Gerada, C. Investigation of AC Copper and Iron Losses in High-Speed High-Power Density PMSM. In Proceedings of the 2018 XIII International Conference on Electrical Machines (ICEM), Alexandroupoli, Greece, 3–6 September 2018; pp. 263–269. [Google Scholar] [CrossRef]
  34. Selema, A.; Ibrahim, M.N.; Sergeant, P. Electrical Machines Winding Technology: Latest Advancements for Transportation Electrification. Machines 2022, 10, 563. [Google Scholar] [CrossRef]
  35. Naderiallaf, H.; Degano, M.; Gerada, C. Assessment of Edgewise Insulated Wire Bend Radius Impact on Dielectric Properties of Turn-to-Turn Insulation through Thermal Ageing. IEEE Trans. Dielectr. Electr. Insul. 2023, 31, 419–428. [Google Scholar] [CrossRef]
  36. Linnemann, M.; Bach, M.; Psyk, V.; Werner, M.; Gerlach, M.; Schubert, N. Resource-efficient, innovative coil production for increased filling factor. In Proceedings of the 2019 9th International Electric Drives Production Conference (EDPC), Esslingen, Germany, 3–4 December 2019; pp. 1–5. [Google Scholar] [CrossRef]
  37. Herrmann, P.; Gerngroß, M.; Endisch, C.; Stenzel, P.; Uhlmann, P. Automated contacting technology for needle winding applications with distributed windings. In Proceedings of the 2017 7th International Electric Drives Production Conference (EDPC), Wuerzburg, Germany, 5–6 December 2017; pp. 1–8. [Google Scholar] [CrossRef]
  38. Fleischer, J. Quo Vadis Winding Technology? Technical Report; Karlsruhe Institute of Technology: Karlsruhe, Germany, 2017. [Google Scholar]
  39. Grosse, T.; Hagedorn, J.; Hameyer, K. Needle winding technology for symmetric distributed windings. In Proceedings of the 2014 4th International Electric Drives Production Conference (EDPC), Nuremberg, Germany, 30 September–1 October 2014. [Google Scholar]
  40. Born, H.C.; Schaffrath, M.; Tege, D.; Brans, F.; Dorn, B.; Heimes, H.; Kampker, A. Analysis of the Influence of Various Bending Parameters on the Resulting Electrical Properties of Bent Hairpins. In Proceedings of the 2023 13th International Electric Drives Production Conference (EDPC), Regensburg, Germany, 29–30 November 2023; pp. 1–8. [Google Scholar] [CrossRef]
  41. Kajita, K.; Takao, T.; Maeda, H.; Yanagisawa, Y. Degradation of a REBCO conductor due to an axial tensile stress under edgewise bending: A major stress mode of deterioration in a high field REBCO coil’s performance. Supercond. Sci. Technol. 2017, 30, 074002. [Google Scholar] [CrossRef]
  42. George, E.; Walker, A.; Zhang, F.; Vakil, G.; Gerada, C. Highly Manufacturable Edgewise Winding Design Integrating Cooling Solutions for High Power Density Applications. In Proceedings of the 2024 IEEE Vehicle Power and Propulsion Conference (VPPC), Washington, DC, USA, 7–10 October 2024; pp. 1–5. [Google Scholar] [CrossRef]
  43. Sadowski, N.; Lefèvre, Y.; Lajoie-Mazenc, M.; Cros, J. Finite element torque calculation in electrical machines while considering the movement. IEEE Trans. Magn. 1992, 28, 1410–1413. [Google Scholar] [CrossRef]
  44. Wirth, F.; Nguyen, C.; Hofmann, J.; Fleischer, J. Characterization of Rectangular Copper Wire Forming Properties and Derivation of Control Concepts for the Kinematic Bending of Hairpin Coils. Procedia Manuf. 2020, 47, 678–685. [Google Scholar] [CrossRef]
  45. Godbehere, J.; Wrobel, R.; Drury, D.; Mellor, P.H. Experimentally calibrated thermal stator modelling of AC machines for short-duty transient operation. In Proceedings of the 2016 XXII International Conference on Electrical Machines (ICEM), Lausanne, Switzerland, 4–7 September 2016; pp. 1721–1727. [Google Scholar] [CrossRef]
  46. Dong, T.; Zhu, C.; Zhang, X.; Zhou, F. Hybrid-Strand Winding Topology With Improved Power Density in Automotive Electric Machines. IEEE Trans. Ind. Electron. 2022, 69, 6036–6045. [Google Scholar] [CrossRef]
Figure 1. V-shaped interior permanent magnet machine cross-sectional layout.
Figure 1. V-shaped interior permanent magnet machine cross-sectional layout.
Energies 18 04572 g001
Figure 2. Edgewise coil structures with end winding profile comparison: (a) edgewise coil profile in parallel slot stator; (b) edgewise coil profile in parallel tooth stator.
Figure 2. Edgewise coil structures with end winding profile comparison: (a) edgewise coil profile in parallel slot stator; (b) edgewise coil profile in parallel tooth stator.
Energies 18 04572 g002
Figure 3. Analytical evaluation of end winding length: (a) stranded winding; (b) edgewise winding.
Figure 3. Analytical evaluation of end winding length: (a) stranded winding; (b) edgewise winding.
Energies 18 04572 g003
Figure 4. Torque delivery per winding structure at fixed current loading factor of 5000 Amp-Turns.
Figure 4. Torque delivery per winding structure at fixed current loading factor of 5000 Amp-Turns.
Energies 18 04572 g004
Figure 5. Thermocouple node locations: (a) stranded coil in parallel tooth stator; (b) edgewise coil in parallel slot stator; (c) edgewise coil in parallel tooth stator.
Figure 5. Thermocouple node locations: (a) stranded coil in parallel tooth stator; (b) edgewise coil in parallel slot stator; (c) edgewise coil in parallel tooth stator.
Energies 18 04572 g005
Figure 6. Edgewise winding facility at University of Nottingham.
Figure 6. Edgewise winding facility at University of Nottingham.
Energies 18 04572 g006
Figure 7. Manufactured motorette with edgewise coils: (a) edgewise coil in parallel slot stator; (b) edgewise coil in parallel tooth stator (Manufactured at University of Nottingham, Nottingham, UK).
Figure 7. Manufactured motorette with edgewise coils: (a) edgewise coil in parallel slot stator; (b) edgewise coil in parallel tooth stator (Manufactured at University of Nottingham, Nottingham, UK).
Energies 18 04572 g007
Figure 8. Initial and “per duplicate” manufacturing times per coil structure.
Figure 8. Initial and “per duplicate” manufacturing times per coil structure.
Energies 18 04572 g008
Figure 9. Experimental rig for motorette DC current.
Figure 9. Experimental rig for motorette DC current.
Energies 18 04572 g009
Figure 10. Steady-state temperature rise per current loading factor for stranded and edgewise PS/PT segment tests.
Figure 10. Steady-state temperature rise per current loading factor for stranded and edgewise PS/PT segment tests.
Energies 18 04572 g010
Table 2. Summary of comparison between stranded and edgewise conductor types.
Table 2. Summary of comparison between stranded and edgewise conductor types.
ParameterStrandedEdgewise
Fill factor0.45–0.550.7–0.75
End winding lengthLongShort
AC loss magnitudeLowMedium
AC loss designStrand size/numberDimensions/aspect ratio
AC/DC loss ratioMediumHigh
Slot equivalent thermal conductivityLowHigh
Manufacturing maturityMatureLower maturity
Upfront costLowHigh
Manufacturing variationHigh Low
Automation potentialMediumHigh
Design optionsHighMedium
Table 3. Base machine geometric and cooling parameters.
Table 3. Base machine geometric and cooling parameters.
Machine Parameters
Outer diameter (mm)245Thermal limit (°C)180
Active length (mm)110CoolingSpiral water jacket
Slots/poles24/8CoolantGlycol–water
Operating speed (RPM)2500Flow rate (LPM)3
Table 4. Comparison of winding parameters.
Table 4. Comparison of winding parameters.
ParameterStrandedEdgewise PSEdgewise PT
StructureEnergies 18 04572 i001Energies 18 04572 i002Energies 18 04572 i003
Turns per coil241212
Turns per phase969696
Parallel paths211
Layers222
Strands in hand211
Fill factor0.4650.7580.564
End winding length (mm)77.8674.6864.24
Available slot area (mm2)318.4235.5318.4
Conductor CSA (mm2)1.32766
Conductors per slot962424
Table 5. Simulated operating point comparison at thermal limit.
Table 5. Simulated operating point comparison at thermal limit.
ParameterStrandedEdgewise PSEdgewise PT
Current (A) 8181103
Current density (A/mm2)15.313.517.2
Torque (Nm)70.67390.9
Current loading (Amp-turns)777677769888
Machine efficiency (%)84.688.886.3
Torque ripple (%)6.26.44.0
Table 6. Simulated operating point comparison at 2500 RPM and 60 Nm.
Table 6. Simulated operating point comparison at 2500 RPM and 60 Nm.
ParameterStrandedEdgewise PSEdgewise PT
Current (A)676665
Current loading (Amp-turns)643263366240
Torque constant 0.6420.6450.662
Efficiency (%)90.692.493.5
Copper losses (DC (W)/AC (W))1491/591199/8.81012/7.5
DC resistance (Ω)0.1110.0920.080
Iron losses (W)84.373.385.9
Table 7. DC resistance measured and calculated comparison.
Table 7. DC resistance measured and calculated comparison.
DC Resistance (mΩ)StrEW-PSEW-PT
Calculated1479.69.0
Measured (peak-to-peak coil variation * %)193.949.384 (6.46)8.815 (0.57)
* The coil variation refers to the difference between the maximum and minimum measured coil resistance among the sample set.
Table 8. Per node temperature rise distribution for maximum steady state current loading factor.
Table 8. Per node temperature rise distribution for maximum steady state current loading factor.
ParameterStrEW-PSEW-PT
Current (A)12.45151
Turns per phase2989696
Current loading factor (Amp-turns)368548964896
TC1 (°C)132.6155.5167.5
TC2 (°C)102.7151.5134.6
TC3 (°C)108.1137.4136.9
End winding (°C)128.6155.6164.8
Hot spot (°C)177.1168.1170.0
Table 9. Stranded and edgewise PS/PT final comparison.
Table 9. Stranded and edgewise PS/PT final comparison.
StrandedEdgewise PSEdgewise PT
Slot equivalent thermal conductivity (W/mK)0.631.711.62
Current (A)8384108
Current density (A/mm2)15.61418
Torque (Nm)74.176.194.7
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Share and Cite

MDPI and ACS Style

George, E.; Walker, A.; Zhang, F.; Vakil, G.; Gerada, C. Experimental Validation of Manufacturable Edgewise Winding Solutions Considering Parallel Slot and Parallel Tooth Stator Structures. Energies 2025, 18, 4572. https://doi.org/10.3390/en18174572

AMA Style

George E, Walker A, Zhang F, Vakil G, Gerada C. Experimental Validation of Manufacturable Edgewise Winding Solutions Considering Parallel Slot and Parallel Tooth Stator Structures. Energies. 2025; 18(17):4572. https://doi.org/10.3390/en18174572

Chicago/Turabian Style

George, Ellis, Adam Walker, Fengyu Zhang, Gaurang Vakil, and Chris Gerada. 2025. "Experimental Validation of Manufacturable Edgewise Winding Solutions Considering Parallel Slot and Parallel Tooth Stator Structures" Energies 18, no. 17: 4572. https://doi.org/10.3390/en18174572

APA Style

George, E., Walker, A., Zhang, F., Vakil, G., & Gerada, C. (2025). Experimental Validation of Manufacturable Edgewise Winding Solutions Considering Parallel Slot and Parallel Tooth Stator Structures. Energies, 18(17), 4572. https://doi.org/10.3390/en18174572

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop