Search Results (11)

Crystal violet (CV) is an organic chloride salt and a triphenylmethane dye commonly used in the textile processing industry, also being used as a disinfectant and a biomedical stain. Although CV is widely used, it is carcinogenic to humans and is retained by industrial-produced effluent for an extended period. The different types of metal oxide (MO_x) have impressive photocatalytic properties, allowing them to be utilized for pollutant degradation. The role of the photocatalyst is to facilitate oxidation and reduction processes by trapping light energy. In this study, we investigated different types of metal oxides, such as titanium dioxide (TiO₂), zinc oxide (ZnO), zirconium dioxide (ZrO₂), iron (III) oxide (Fe₂O₃), copper (II) oxide (CuO), copper (I) oxide (Cu₂O), and niobium pentoxide (Nb₂O₅) for the CV decomposition reaction at ambient conditions. For characterization, BET and Raman spectroscopy were applied, providing findings showing that the surface area of the anatase TiO₂ and ZnO were 5 m²/g and 12.1 m²/g, respectively. The activity tests over TiO₂ and ZnO catalysts revealed that up to ~98% of the dye could be decomposed under UV irradiation in <2 h. The decomposition of CV is directly influenced by various factors, such as the types of MO_x, the band gap–water splitting relationship, and the recombination rate of electron holes. Full article

The research of starch as a matrix material for manufacturing biodegradable films has been gaining popularity in recent years, indicating its potential and possible limitations. To compete with conventional petroleum-based plastics, an enhancement of their low resistance to water and limited mechanical properties is essential. This review aims to discuss the various types of nanofillers and additives that have been used in plasticized starch films including nanoclays (montmorillonite, halloysite, kaolinite, etc.), poly-saccharide nanofillers (cellulose, starch, chitin, and chitosan nanomaterials), metal oxides (titanium dioxide, zinc oxide, zirconium oxide, etc.), and essential oils (carvacrol, eugenol, cinnamic acid). These reinforcements are frequently used to enhance several physical characteristics including mechanical properties, thermal stability, moisture resistance, oxygen barrier capabilities, and biodegradation rate, providing antimicrobial and antioxidant properties. This paper will provide an overview of the development of starch-based nanocomposite films and coatings applied in food packaging systems through the application of reinforcements and additives. Full article

The progress in nanotechnology has effectively tackled and overcome numerous global issues, including climate change, environmental contamination, and various lethal diseases. The nanostructures being a vital part of nanotechnology have been synthesized employing different physicochemical methods. However, these methods are expensive, polluting, eco-unfriendly, and produce toxic byproducts. Green chemistry having exceptional attributes, such as cost-effectiveness, non-toxicity, higher stability, environment friendliness, ability to control size and shape, and superior performance, has emerged as a promising alternative to address the drawbacks of conventional approaches. Plant extracts are recognized as the best option for the biosynthesis of nanoparticles due to adherence to the environmentally benign route and sustainability agenda 2030 of the United Nations. In recent decades, phytosynthesized nanoparticles have gained much attention for different scientific applications. Eucalyptus globulus (blue gum) is an evergreen plant belonging to the family Myrtaceae, which is the targeted point of this review article. Herein, we mainly focus on the fabrication of nanoparticles, such as zinc oxide, copper oxide, iron oxide, lanthanum oxide, titanium dioxide, magnesium oxide, lead oxide, nickel oxide, gold, silver, and zirconium oxide, by utilizing Eucalyptus globulus extract and its essential oils. This review article aims to provide an overview of the synthesis, characterization results, and biomedical applications of nanoparticles synthesized using Eucalyptus globulus. The present study will be a better contribution to the readers and the students of environmental research. Full article

The development of scaffold-based nanofilms for the acceleration of wound healing and for maintaining the high level of the healthcare system is still a challenge. The use of naturally sourced polymers as binders to deliver nanoparticles to sites of injury has been highly suggested. To this end, chitosan (CS) was embedded with different nanoparticles and examined for its potential usage in wound dressing. In detail, chitosan (CS)-containing zinc sulfide (ZnS)/zirconium dioxide (ZrO₂)/graphene oxide (GO) nanocomposite films were successfully fabricated with the aim of achieving promising biological behavior in the wound healing process. Morphological examination by SEM showed the formation of porous films with a good scattering of ZnS and ZrO₂ nanograins, especially amongst ZnS/ZrO₂/GO@CS film. In addition, ZnS/ZrO₂/GO@CS displayed the lowest contact angle of 67.1 ± 0.9°. Optically, the absorption edge records 2.35 eV for pure chitosan, while it declines to 1.8:1.9 scope with the addition of ZnS, ZrO₂, and GO. Normal lung cell (WI-38) proliferation inspection demonstrated that the usage of 2.4 µg/mL ZnS/ZrO₂/GO@CS led to a cell viability % of 142.79%, while the usage of 5000 µg/ mL led to a viability of 113.82%. However, the fibroblast malignant cell line exposed to 2.4 µg/mL ZnS/ZrO₂/GO@CS showed a viability % of 92.81%, while this percentage showed a steep decline with the usage of 5000 µg/ mL and 2500 µg/mL, reaching 23.28% and 27.81%, respectively. Further biological assessment should be executed with a three-dimensional film scaffold by choosing surrounding media characteristics (normal/malignant) that enhance the selectivity potential. The fabricated scaffolds show promising selective performance, biologically. Full article

The emergence of mixed matrix membranes (MMMs) or nanocomposite membranes embedded with inorganic nanoparticles (NPs) has opened up a possibility for developing different polymeric membranes with improved physicochemical properties, mechanical properties and performance for resolving environmental and energy-effective water purification. This paper presents an overview of the effects of different hydrophilic nanomaterials, including mineral nanomaterials (e.g., silicon dioxide (SiO₂) and zeolite), metals oxide (e.g., copper oxide (CuO), zirconium dioxide (ZrO₂), zinc oxide (ZnO), antimony tin oxide (ATO), iron (III) oxide (Fe2O3) and tungsten oxide (WO_X)), two-dimensional transition (e.g., MXene), metal–organic framework (MOFs), covalent organic frameworks (COFs) and carbon-based nanomaterials (such as carbon nanotubes and graphene oxide (GO)). The influence of these nanoparticles on the surface and structural changes in the membrane is thoroughly discussed, in addition to the performance efficiency and antifouling resistance of the developed membranes. Recently, GO has shown a considerable capacity in wastewater treatment. This is due to its nanometer-sized holes, ultrathin layer and light and sturdy nature. Therefore, we discuss the effect of the addition of hydrophilic GO in neat form or hyper with other nanoparticles on the properties of different polymeric membranes. A hybrid composite of various NPs has a distinctive style and high-quality products can be designed to allow membrane technology to grow and develop. Hybrid composite NPs could be used on a large scale in the future due to their superior mechanical qualities. A summary and future prospects are offered based on the current discoveries in the field of mixed matrix membranes. This review presents the current progress of mixed matrix membranes, the challenges that affect membrane performance and recent applications for wastewater treatment systems. Full article

The photocatalytic degradation of Rhodamine 6G dye was achieved using a Ficus elastica (F. elastic) leaf extract mediated zinc oxide-zirconium dioxide nanocatalyst (ZnO-ZrO₂ NC) under stimulated solar light, resulting in a substantial increase in photocatalytic activity at the highest calcination temperature. The crystal phase and crystallite size were determined using an X-ray diffractometer (XRD), and the degree of crystallinity was observed to rise with increasing calcination temperature. Energy dispersive X-ray (EDX) was used to investigate the elemental composition and purity of ZnO-ZrO₂ NC. Scanning electron microscopy (SEM) was used to investigate the surface morphology, and the morphological characteristics were altered when the calcination temperature was varied. For the ZnO-ZrO₂ NC calcined at 100, 300, 600, and 900 °C, the average grain size determined from SEM images is 79.56 nm, 98.78 (2) nm, 54.86 (2) nm, and 67.43 (2) nm, respectively. Using diffuse reflectance spectroscopy (DRS) data, the optical band gap energy was calculated using a Tauc’s plot. The ZnO in ZnO-ZrO₂ NC calcined at 100, 300, 600, and 900 °C had band gap energies of 3.31, 3.36, 3.38, and 3.29 eV. Similarly, ZrO₂ in ZnO-ZrO₂ NC calcined at 100, 300, 600, and 900 °C had band gap energies of 3.96, 3.99, 3.97, and 4.01 eV, respectively. Fourier transform infrared (FTIR) spectroscopy was used to identify the presence of various functional groups. The photocatalytic activity was also examined in relation to calcination temperature, pH, starting concentration, and catalyst dosage. Enhanced photocatalytic activity was observed at pH 11 and 15 ppm initial concentration with a catalyst dose of 25 mg. The photocatalytic activity of the sample calcined at 900 °C was the highest, with 98.94 percent of the dye mineralized in 330 min at a degradation rate of 0.01261/min. Full article

The zinc oxide–zirconium dioxide (ZnO-ZrO₂) heterojunction was prepared by a green method using rubber leaves as reducing and capping agents. Various physicochemical techniques were used to study the chemical composition and the structural and optical properties of the synthesized nanocomposite. The nature of the heterojunction was confirmed through X-ray diffraction and the average sizes of ZnO and ZrO₂ crystallites were found to be 70 and 24 nm, respectively. The photocatalytic potential of the ZnO-ZrO₂ heterojunction was examined against rhodamine 6G (Rh-6G), and 97.30 percent of the dye was degraded due to the synergistic effect of the light and the catalyst. The commercial ZnO nanopowder was used as a reference catalyst and 86.32 percent degradation was noted under the same reaction conditions. The in vitro antioxidant activity was also performed to scavenge the 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) free radicals, where the activity of the ZnO-ZrO₂ heterojunction was found to be higher than the ascorbic acid. Full article

The elimination of antibiotics occurring in the natural environment has become a great challenge in recent years. Among other techniques, the photocatalytic degradation of this type of pollutant seems to be a promising approach. Thus, the search for new photoactive materials is currently of great importance. The present study concerns the sol–gel synthesis of mono, binary and ternary TiO₂-based materials, which are used as active photocatalysts. The main goal was to evaluate how the addition of selected components—zirconium dioxide (ZrO₂) and/or zinc oxide (ZnO)—during the synthesis of TiO₂-based materials and the temperature of thermal treatment affect the materials’ physicochemical and photocatalytic properties. The fabricated mixed oxide materials underwent detailed physicochemical analysis, utilizing scanning-electron microscopy (SEM), X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), energy-dispersive X-ray spectroscopy (EDS), low-temperature N₂ sorption (BET model), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). The synthesized mixed oxide materials were used as photocatalysts in the heterogeneous photodegradation of tetracycline (TC). The physicochemical properties of the fabricated photocatalysts, including morphology, crystalline and textural structure, as well as the pH of the reaction system in the photocatalytic tests, were taken into account in determining their photo-oxidation activity. LC–MS/MS analysis was used to identify the possible degradation products of the selected antibiotic. Full article

Shellac is a natural varnish still known as one of the most elegant finishes for furniture and musical instruments, and currently used for restoration and refinishing of wooden antiques. However, it displays some limitations such as (i) sensitivity to alcoholic solvents (ii) softness of the coating, and (iii) considerable weathering due to photo- and bio-degradation. Hence, the main aim of this study was to improve the properties of shellac-based finish by introducing functionalized nanoparticles. Two inorganic nano-sized materials were considered: ZnO that was expected to reduce photo- and bio-degradation problems, and ZrO₂ that was expected to improve the hardness of the varnish. Nanoparticles were synthesized and treated with a bifunctional silane coupling agent. Both plain and functionalized nanoparticles were extensively characterized using different experimental techniques. Functionalized nanoparticles were grafted on shellac through a reaction involving the epoxy-rings introduced on their surface. The resulting modified varnishes were applied on maple wood specimens according to traditional procedures. Different instrumental techniques and testing methods were used to characterize both nano-sized materials and the corresponding nanocomposites, as well as to evaluate the performance of the new coatings. The investigated composite materials display the same aesthetic appearance as plain shellac, while some other properties were improved. In particular, both nanocomposites are distinctly less soluble in alcohols than plain shellac and display antifungal properties. Moreover, coating containing functionalized ZnO nanoparticles displays photo-protection behavior, while shellac modified with ZrO₂ nanoparticles exhibits a higher hardness when compared to the traditional varnish. Full article

Since there is no potential, effective vaccine available, treatment is the only controlling option against hydatid cyst or cystic echinococcosis (CE). This study was designed to systematically review the in vitro, in vivo, and ex vivo effects of nanoparticles against hydatid cyst. The study was carried out based on the 06- PRISMA guideline and registered in the CAMARADES-NC3Rs Preclinical Systematic Review and Meta-analysis Facility (SyRF) database. The search was performed in five English databases, including Scopus, PubMed, Web of Science, EMBASE, and Google Scholar without time limitation for publications around the world about the protoscolicdal effects of all the organic and inorganic nanoparticles without date limitation in order to identify all the published articles (in vitro, in vivo, and ex vivo). The searched words and terms were: “nanoparticles”, “hydatid cyst”, “protoscoleces”, “cystic echinococcosis”, “metal nanoparticles”, “organic nanoparticles”, “inorganic nanoparticles, “in vitro”, ex vivo”, “in vivo”. Out of 925 papers, 29 papers including 15 in vitro (51.7%), 6 in vivo (20.7%), ex vivo 2 (6.9%), and 6 in vitro/in vivo (20.7%) up to 2020 met the inclusion criteria for discussion in this systematic review. The results demonstrated the most widely used nanoparticles in the studies were metal nanoparticles such as selenium, silver, gold, zinc, copper, iron nanoparticles (n = 8, 28.6%), and metal oxide nanoparticles such as zinc oxide, titanium dioxide, cerium oxide, zirconium dioxide, and silicon dioxide (n = 8, 28.6%), followed by polymeric nanoparticles such as chitosan and chitosan-based nanoparticles (n = 7, 25.0%). The results of this review showed the high efficacy of a wide range of organic and inorganic NPs against CE, indicating that nanoparticles could be considered as an alternative and complementary resource for CE treatment. The results demonstrated that the most widely used nanoparticles for hydatid cyst treatment were metal nanoparticles and metal oxide nanoparticles, followed by polymeric nanoparticles. We found that the most compatible drugs with nanoparticles were albendazole, followed by praziquantel and flubendazole, indicating a deeper understanding about the synergistic effects of nanoparticles and the present anti-parasitic drugs for treating hydatid cysts. The important point about using these nanoparticles is their toxicity; therefore, cytotoxicity as well as acute and chronic toxicities of these nanoparticles should be considered in particular. As a limitation, in the present study, although most of the studies have been performed in vitro, more studies are needed to confirm the effect of these nanoparticles as well as their exact mechanisms in the hydatid cyst treatment, especially in animal models and clinical settings. Full article

Recently, wastewater treatment by photocatalytic oxidation processes with metal oxide nanomaterials and nanocomposites such as zinc oxide, titanium dioxide, zirconium dioxide, etc. using ultraviolet (UV) and visible light or even solar energy has added massive research importance. This waste removal technique using nanostructured photocatalysts is well known because of its effectiveness in disintegrating and mineralizing the unsafe organic pollutants such as organic pesticides, organohalogens, PAHs (Polycyclic Aromatic Hydrocarbons), surfactants, microorganisms, and other coloring agents in addition to the prospect of utilizing the solar and UV spectrum. The photocatalysts degrade the pollutants using light energy, which creates energetic electron in the metal oxide and thus generates hydroxyl radical, an oxidative mediator that can oxidize completely the organic pollutant in the wastewater. Altering the morphologies of metal oxide photocatalysts in nanoscale can further improve their photodegradation efficiency. Nanoscale features of the photocatalysts promote enhance light absorption and improved photon harvest property by refining the process of charge carrier generation and recombination at the semiconductor surfaces and in that way boost hydroxyl radicals. The literature covering semiconductor nanomaterials and nanocomposite-assisted photocatalysis—and, among those, metal oxide nanofibers—suggest that this is an attractive route for environmental remediation due to their capability of reaching complete mineralization of organic contaminants under mild reaction conditions such as room temperature and ambient atmospheric pressure with greater degradation performance. The main aim of this review is to highlight the most recent published work in the field of metal oxide nanofibrous photocatalyst-mediated degradation of organic pollutants and unsafe microorganisms present in wastewater. Finally, the recycling and reuse of photocatalysts for viable wastewater purification has also been conferred here and the latest examples given. Full article