Search Results (7)

Intumescent coatings are widely used to enhance the fire resistance of structural steel. In contrast to traditional fire protection methods, this novel flexible intumescent protection offers several key advantages: universal compatibility with other coatings (via non-contact wrapping), resistance to extreme temperatures (−60 °C to +90 °C), all-weather usability, and suitability for light-gauge cold-formed thin-walled steel structures. This paper describes the development and investigation of these fire-protective, flexible intumescent coatings based on eco-friendly binders (silicone polymers and acrylic resins) with varying intercalated graphite (IG) content from 0% to 40%. An IG content of 25–40% enables a steel I-section with a section factor of 294 mm⁻¹ to reach its limit state at 44 min (compared to 15 min for unprotected steel). Fire tests on steel beams with a section factor of 172 mm⁻¹ demonstrated that samples reached the deflection limit state at the 64th and 66th minutes, respectively. Thermogravimetric analysis (TGA) was used to determine the temperature ranges for the thermal decomposition and expansion of the IG. Mechanical property studies revealed the influence of IG on the elastic modulus and tensile strength. Accelerated climatic testing in moderately cold conditions and salt spray chamber tests confirmed that the intumescent roll coating has no negative impact on the steel substrates. Full article

The curing quality of epoxy resin at wind turbine blade joint seams critically affects blade integrity and service reliability, yet conventional metallic heating systems often suffer from poor temperature uniformity, limited flexibility, and slow thermal response. In this study, a flexible and lightweight heating blanket based on carbon nanotube (CNT) electrothermal film was developed for blade reinforcement and in situ curing applications. The device employs a multilayer composite architecture consisting of a CNT heating layer, a nano-aerogel thermal insulation layer, a thermoplastic polyurethane electrical insulation layer, and a silicone-coated glass fiber protective layer, together with an intelligent temperature control system. The resulting blanket, with a total thickness of 3.85 mm, exhibited rapid and stable heating performance, increasing from 25 to 120 °C within 8 min. Under resin-curing conditions, it achieved an initial heating rate of 7.2 °C min⁻¹ and a temperature uniformity of ±2.6 °C, markedly outperforming a conventional Ni@Cr alloy heating blanket. Accelerated aging tests further demonstrated stable electrothermal performance under the tested condition. Those results indicate that the proposed CNT-based heating blanket provides an efficient and reliable thermal management strategy for large curved composite structures. Full article

Benzoxazine resins are gaining attention for their impressive thermal stability, low water uptake, and strong mechanical properties. In this work, two new bio-based benzoxazine monomers were developed using renewable arbutin: one combined with 3-(2-aminoethylamino) propyltrimethoxysilane (AB), and the other with furfurylamine (AF). Both were synthesized using a simple Mannich-type reaction and verified through FT-IR and ¹H-NMR spectroscopy. By blending these monomers in different ratios, copolymers with adjustable thermal, dielectric, and surface characteristics were produced. Thermal analysis showed that the materials had broad processing windows and cured effectively, while thermogravimetric testing confirmed excellent heat resistance—especially in AF-rich blends, which left behind more char. The structural changes obtained during curing process were monitored using FT-IR, and XPS verified the presence of key elements like carbon, oxygen, nitrogen, and silicon. SEM imaging revealed that AB-based materials had smoother surfaces, while AF-based ones were rougher; the copolymers fell in between. Dielectric testing showed that increasing AF content raised both permittivity and loss, and contact angle measurements confirmed that surfaces ranged from water-repellent (AB) to water-attracting (AF). Overall, these biopolymers (AB/AF copolymers) synthesized from arbutin combine environmental sustainability with customizability, making them strong candidates for use in electronics, protective coatings, and flame-resistant composite materials. Full article

To enhance protection against corrosion and ice on iron metal material in frigid zones, an organic silicone resin coating was prepared using four monomers. Its structure and performance was analyzed via infrared spectroscopy (FTIR), nuclear magnetic resonance (NMR), gel permeation chromatography (GPC), and thermal analysis (TG). Corrosion resistance of coating was tested by saltwater resistance and salt spray resistance and assessed using an electrochemical workstation, alongside anti-icing tests. The results showed that the organic silicone resin was successfully synthesized. The coatings could delay freezing onset by one-third compared to controls in low temperatures, with a detachment time also reduced by one-third, indicating excellent corrosion and ice resistance. The methylphenyl silicone resin had good anti-corrosion and anti-ice properties, with a low corrosion current density (i_corr) of 0.8793 μA/cm² and a high charge transfer resistance (R_ct) of 24,930 Ω·cm² in saline. Full article

As a bridge between the coating and the substrate, the primer has a direct impact on the adhesion performance of silicone resin thermal protection coating. In this paper, the synergistic effects of an aminosilane coupling agent on the adhesion performance of silane primer were investigated. The results show that silane primer containing N-aminoethyl-3-aminopropylmethyl-dimethoxysilane (HD-103) formed a continuous and uniform film on the surface of the substrate. Two amino groups of HD-103 were conducive to moderate and uniform hydrolysis of the silane primer system, and the introduction of dimethoxy groups was more conducive to the improvement of interfacial layer density and the formation of the planar surface structure, thus enhancing the bond strength at the interface. When the content was 13 wt%, it exhibited excellent synergistic effects on adhesive properties, and the adhesive strength reached 1.53 MPa. The possible morphology and composition of the silane primer layer were investigated by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). A thermogravimetric infrared spectrometer (TGA-IR) was used to analyze the thermal decomposition of the silane primer layer. The results showed that the alkoxy groups in the silane primer were first hydrolyzed to form Si-OH, and then the dehydration and condensation reactions between Si-OH and the substrate formed a firm network structure. Full article

Silicone resins are widely applied as coating materials due to their unique properties, especially those related to very good heat resistance. The most important effect on the long-term heat resistance of the coating is connected with the type of resin. Moreover, this structure is stabilized by a chemical reaction between the hydroxyl groups from the organoclay and the silicone resin. The novel trends in application of silicone resins in intumescent paints used mostly for protection of steel structures against fire will be presented based on literature review. Some examples of innovative applications for fire protection of other materials will be also presented. The effect of silicone resin structure and the type of filler used in these paints on the properties of the char formed during the thermal decomposition of the intumescent paint will be discussed in detail. The most frequently used additives are expanded graphite and organoclay. It has been demonstrated that silicate platelets are intercalated in the silicone matrix, significantly increasing its mechanical strength and resulting in high protection against fire. Full article

This article reviews the applications of silicone resins as ceramic precursors. The historical background of silicone synthesis chemistry is introduced to explain the production costs and supply availability of various silicones. Thermal degradation processes of silicones are classified in terms of the main chain structure and cyclic oligomer expulsion process, which determine the resulting ceramic yield and the chemical composition. The high temperature decomposition of Si-O-C beyond 1,400 °C in an inert atmosphere and formation of a protective silica layer on material surfaces beyond 1,200 °C in an oxidative atmosphere are discussed from the viewpoints of the wide chemical composition of the Si-O-C materials. Applications of the resins for binding agents, as starting materials for porous ceramics, matrix sources with impregnation, fiber spinning and ceramic adhesions are introduced. The recent development of the process of filler or cross-linking agent additions to resin compounds is also introduced. Such resin compounds are useful for obtaining thick coatings, MEMS parts and bulk ceramics, which are difficult to obtain by pyrolysis of simple organometallic precursors without additives. Full article