Search Results (107)

The article discusses the design, fabrication, and experimental evaluation of a large-area vertical grating coupler (VGC) enabling simultaneous coupling of multiple input optical beams. The presented VCG was fabricated by direct nanoimprinting of a grating pattern in a non-hardened SiO_X:TiO_Y waveguide (WG) film. The WG film was deposited on a glass substrate using a combination of the sol–gel method and the dip-coating technique. The fabrication process allowed precise control of the waveguide film thickness and refractive index, as well as the VGC geometry. The relevance of the process was proved by a demonstration of optical coupling of multiple quasi-parallel input beams via the VGC to the WG layer. To make this possible, a dedicated optical coupling system was designed, including a polymer microlens array and optical fiber array positioned in a V-groove. This opens promising perspectives on using the proposed structure for the fabrication of low-cost multichannel optical sensor chips, as highlighted in the article’s final section. Full article

Nanotopography refers to the intricate surface characteristics of materials at the sub-micron (<1000 nm) and nanometer (<100 nm) scales. These topographical surface features significantly influence the physical, chemical, and biological properties of biomaterials, affecting their interactions with cells and surrounding tissues. The development of nanostructured surfaces of polymeric nanocomposites has garnered increasing attention in the fields of tissue engineering and regenerative medicine due to their ability to modulate cellular responses and enhance tissue regeneration. Various top-down and bottom-up techniques, including nanolithography, etching, deposition, laser ablation, template-assisted synthesis, and nanografting techniques, are employed to create structured surfaces on biomaterials. Additionally, nanotopographies can be fabricated using polymeric nanocomposites, with or without the integration of organic and inorganic nanomaterials, through advanced methods such as using electrospinning, layer-by-layer (LbL) assembly, sol–gel processing, in situ polymerization, 3D printing, template-assisted methods, and spin coating. The surface topography of polymeric nanocomposite scaffolds can be tailored through the incorporation of organic nanomaterials (e.g., chitosan, dextran, alginate, collagen, polydopamine, cellulose, polypyrrole) and inorganic nanomaterials (e.g., silver, gold, titania, silica, zirconia, iron oxide). The choice of fabrication technique depends on the desired surface features, material properties, and specific biomedical applications. Nanotopographical modifications on biomaterials’ surface play a crucial role in regulating cell behavior, including adhesion, proliferation, differentiation, and migration, which are critical for tissue engineering and repair. For effective tissue regeneration, it is imperative that scaffolds closely mimic the native extracellular matrix (ECM), providing a mechanical framework and topographical cues that replicate matrix elasticity and nanoscale surface features. This ECM biomimicry is vital for responding to biochemical signaling cues, orchestrating cellular functions, metabolic processes, and subsequent tissue organization. The integration of nanotopography within scaffold matrices has emerged as a pivotal regulator in the development of next-generation biomaterials designed to regulate cellular responses for enhanced tissue repair and organization. Additionally, these scaffolds with specific surface topographies, such as grooves (linear channels that guide cell alignment), pillars (protrusions), holes/pits/dots (depressions), fibrous structures (mimicking ECM fibers), and tubular arrays (array of tubular structures), are crucial for regulating cell behavior and promoting tissue repair. This review presents recent advances in the fabrication methodologies used to engineer nanotopographical microenvironments in polymeric nanocomposite tissue scaffolds through the incorporation of nanomaterials and biomolecular functionalization. Furthermore, it discusses how these modifications influence cellular interactions and tissue regeneration. Finally, the review highlights the challenges and future perspectives in nanomaterial-mediated fabrication of nanotopographical polymeric scaffolds for tissue engineering and regenerative medicine. Full article

The development of eco-friendly paint formulations is part of the transition process to more sustainable materials, which involves many industries such as offshore and shipbuilding, where the deterioration of steel in seawater is a key factor. This article aims to produce innovative coatings and test their protective action on DH 36 steel plates. SiO₂ and TiO₂ were modified with amino groups and iron sites to be used as filler for the design of ecological paint formulations The antimicrobial features of both NH₂ groups and iron ionic species were combined with the chemical and mechanical stability of silica and titania, with silica-based powders showing increased efficacy. The surface properties of the resulting coatings were examined by determination of thickness, water wettability, roughness, and cross-cut adhesion tests (before and after a degradation test in seawater according to ASTM D870-97 standards). Preliminary tests of the microbiological activity of the iron amino functionalized materials were carried out to monitor, as proof of concept, the growth of some bacterial strains through measurements of optical density. The findings indicate that these coatings not only provide effective corrosion protection but are promising for enhancing the durability and environmental performance of steel surfaces exposed to marine environments. Full article

Fibrous SiO₂-TiO₂ (FST) is one of the most promising materials for advancing photoelectrochemical water-splitting technology due to its cost-effectiveness and environmental friendliness. However, FST faces intrinsic limitations, including its low conductivity and wide bandgap. In this study, significant progress was made in modifying FST to overcome some of these limitations. This work involved synthesizing a new photoanode made of Ag-doped FST utilizing the microemulsion process. The Ag-doped FST was characterized using XRD, FTIR, UV–Vis, DRS, N₂ adsorption–desorption, FESEM, TEM, and XPS. The results confirmed the formation of a continuous concentric lamellar structure with a large surface area. The addition of Ag species into the FST matrix caused interactions that reduced the bandgap. The Ag-doped FST photoanode exhibited an impressive photocurrent density of 13.98 mA/cm² at 1.2 V (vs. RHE). This photocurrent density was notably higher than that of FST photoanodes, which was 11.65 mA/cm² at 1.2 V (vs. RHE). Furthermore, the conduction band of Ag-doped FST is positioned closer to the reduction potential of hydrogen compared to that of FST, SiO₂, and TiO₂, facilitating rapid charge transfer and enabling the spontaneous generation of H₂. The fabrication of Ag-doped FST provides valuable insights into the development of high-performance photoanodes for PEC water splitting. Full article

Developing a durable multifunctional superhydrophobic coating on polymeric films that can be industrially scalable is a challenge in the field of surface engineering. This article presents a novel method for a scalable technology using a simple single-step fabrication of a superhydrophobic coating on polymeric films that exhibits excellent water-repelling and UV-blocking properties, along with impressive wear resistance and chemical robustness. A mixture of titanium precursors, tetraethylorthosilicate (TEOS), hydrophobic silanes and silica nano/micro-particles is polymerized directly on a corona-treated polymeric film which reacts with the surface via siloxane chemistry. The mixture is then spread on polymeric films using a Mayer rod, which eliminates the need for expensive equipment or multistep processes. The incorporation of silica nanoparticles along with titanium precursor and TEOS results in the formation of a silica–titania network around the silica nanoparticles. This chemically binds them to the activated surface, forming a unique dual-scale surface morphology depending on the size of the silica nanoparticles used in the coating mixture. The coated films were shown to be superhydrophobic with a high water contact angle of over 180° and a rolling angle of 0°. This is due to the combination of dual-scale micro/nano roughness with fluorinated hydrocarbons that lowered the surface free energy. The coatings exhibited excellent chemical and mechanical durability, as well as UV-blocking capabilities. The results show that the coatings remain superhydrophobic even after a sandpaper abrasion test under a pressure of 2.5 kPa for a distance of 30 m. Full article

Mesoporous titania nanoparticles (NPs) can be used for encapsulation polyphenols, with applications in the food industry, cosmetics, or biomedicine. TiO₂ NPs were synthesized using the sol-gel method combined with solvothermal treatment. TiO₂ NPs were characterized through X-ray diffraction, FTIR spectroscopy, the N₂ adsorption method, scanning and transmission electron microscopy, and thermal analysis. The sample prepared using Pluronic F127 presented a higher surface area and less agglomerated NPs than the samples synthesized with Pluronic P123. Grape marc (GM), a by-product from wine production, can be exploited for preparing extracts with good antioxidant properties. In this regard, we prepared hydroethanolic and ethanolic GM extracts from two cultivars, Feteasca Neagra (FN) and Pinot Noir. The extract components were determined by spectrometric analyses and HPLC. The extract with the highest radical scavenging activity, the hydroethanolic FN extract, was encapsulated in titania (FN@TiO₂) and compared with SBA-15 silica support. Both resulting materials showed biocompatibility on the NCTC fibroblast cell line in a 50–300 µg/mL concentration range after 48 h of incubation and even better radical scavenging potential than the free extract. Although titania has a lower capacity to host polyphenols than SBA-15, the FN@TiO₂ sample shows better cytocompatibility (up to 700 µmg/mL), and therefore, it could be used for skin-care products. Full article

This study investigates the significant impact of metal–support interactions on catalytic reaction mechanisms at the interface of oxide-supported metal nanoparticles. The distinct and contrasting effects of SiO₂ and TiO₂ supports on reaction dynamics using NaBD₄ were studied and focused on the relative yields of [HD]/[H₂] and [D₂]/[H₂]. The findings show a consistent increase in HD yields with rising [BD₄⁻] concentrations. Notably, the sequence of HD yield enhancement follows the order of TiO₂-Au⁰-NPs < Au⁰-NPs < SiO₂-Au⁰-NPs. Conversely, the rate of H₂ evolution during BH₄^- hydrolysis exhibits an inverse trend, with TiO₂-Au⁰-NPs outperforming the others, followed by Au⁰-NPs and SiO₂-Au⁰-NPs, demonstrating the opposing effects exerted by the TiO₂ and SiO₂ supports on the catalytic processes. Further, the catalytic reduction of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP) confirms the catalytic mechanism, with TiO₂-Au⁰-NPs demonstrating superior activity. The catalytic activity observed aligns with the order of TiO₂-Au⁰-NPs > Au⁰-NPs > SiO₂-Au⁰-NPs, suggesting that SiO₂ donates electrons to Au⁰-NPs, while TiO₂ withdraws them. It is of interest to note that two very different processes, that clearly proceed via different mechanisms, are affected similarly by the supports. This study reveals that the choice of support material influences catalytic activity, impacting overall yield and efficiency. These findings underscore the importance of selecting appropriate support materials for tailored catalytic outcomes. Full article

Industrial activities generate enormous quantities of polluted effluents, necessitating advanced methods of wastewater treatment to prevent potential environmental threats. Thus, the design of a novel photocatalytic reactor for industrial water decontamination, purification, and reuse is proposed as an efficient advanced oxidation technology. In this work, the development of the active reactor components is described, utilizing a two-step sol–gel technique to prepare a silica-titania trilayer coating on 3D-printed polymeric filters. The initial dip-coated SiO₂ insulator further protects and enhances the stability of the polymer matrix, and the subsequent TiO₂ layers endow the composite architecture with photocatalytic functionality. The structural and morphological characteristics of the modified photocatalytic filters are extensively investigated, and their performance is assessed by studying the photocatalytic degradation of the Triton X-100, a common and standard chemical surfactant, presented in the contaminated wastewater of the steel metal industry. The promising outcomes of the innovative versatile reactor pave the way for developing scalable, cost-effective reactors for efficient water treatment technologies. Full article

Advanced oxidation processes, including photocatalysis, have been proven effective at organic dye degradation. Tailored porous materials with regulated pore size, shape, and morphology offer a sustainable solution to the water pollution problem by acting as support materials to grafted photocatalytic nanoparticles (NPs). This research investigated the influence of pore and particle sizes of photocatalytic MICROSCAFS^® on the degradation of methyl orange (MO) in aqueous solution (10 mg/L). Photocatalytic MICROSCAFS^® are made of binder-less supported P25 TiO₂ NPs within MICROSCAFS^®, which are silica–titania microspheres with a controlled size and interconnected macroporosity, synthesized by an adapted sol–gel method that involves a polymerization-induced phase separation process. Photocatalytic experiments were performed both in batch and flow reactors, with this latter one targeting a proof of concept for continuous transformation processes and real-life conditions. Photocatalytic degradation of 87% in 2 h (batch) was achieved, using a calibrated solar light simulator (1 sun) and a photocatalyst/pollutant mass ratio of 23. This study introduces a novel flow kinetic model which provides the modeling and simulation of the photocatalytic MICROSCAFS^® performance. A scavenger study was performed, enabling an in-depth mechanistic understanding. Finally, the transformation products resulting from the MO photocatalytic degradation were elucidated by high-resolution mass spectrometry experiments and subjected to an in silico toxicity assessment. Full article

Shape memory and self-healing polymer nanocomposites have attracted considerable attention due to their modifiable properties and promising applications. The incorporation of nanomaterials (polypyrrole, carboxyl methyl cellulose, carbon nanotubes, titania nanotubes, graphene, graphene oxide, mesoporous silica) into these polymers has significantly enhanced their performance, opening up new avenues for diverse applications. The self-healing capability in polymer nanocomposites depends on several factors, including heat, quadruple hydrogen bonding, π–π stacking, Diels–Alder reactions, and metal–ligand coordination, which collectively govern the interactions within the composite materials. Among possible interactions, only quadruple hydrogen bonding between composite constituents has been shown to be effective in facilitating self-healing at approximately room temperature. Conversely, thermo-responsive self-healing and shape memory polymer nanocomposites require elevated temperatures to initiate the healing and recovery processes. Thermo-responsive (TRSMPs), light-actuated, magnetically actuated, and Electrically actuated Shape Memory Polymer Nanocomposite are discussed. This paper provides a comprehensive overview of the different types of interactions involved in SMP and SHP nanocomposites and examines their behavior at both room temperature and elevated temperature conditions, along with their biomedical applications. Among many applications of SMPs, special attention has been given to biomedical (drug delivery, orthodontics, tissue engineering, orthopedics, endovascular surgery), aerospace (hinges, space deployable structures, morphing aircrafts), textile (breathable fabrics, reinforced fabrics, self-healing electromagnetic interference shielding fabrics), sensor, electrical (triboelectric nanogenerators, information energy storage devices), electronic, paint and self-healing coating, and construction material (polymer cement composites) applications. Full article

Thin, supported inorganic mesoporous membranes are used for the removal of salts, small molecules (PFAS, dyes, and polyanions) and particulate species (oil droplets) from aqueous sources with high flux and selectivity. Nanofiltration membranes can reject simple salts with 80–100% selectivity through a space charge mechanism. Rejection by size selectivity can be near 100% since the membranes can have a very narrow size distribution. Mesoporous membranes have received particular interest due to their (potential) stability under operational conditions and during defouling operations. More recently, membranes with extreme stability became interesting with the advent of in situ fouling mitigation by means of ultrasound emitted from within the membrane structure. For this reason, we explored the stability of available and new membranes with accelerated lifetime tests in aqueous solutions at various temperatures and pH values. Of the available ceria, titania, and magnetite membranes, none were actually stable under all test conditions. In earlier work, it was established that mesoporous alumina membranes have very poor stability. A new nanofiltration membrane was made of cubic zirconia membranes that exhibited near-perfect stability. A new ultrafiltration membrane was made of amorphous silica that was fully stable in ultrapure water at 80 °C. This work provides details of membrane synthesis, stability characterization and data and their interpretation. Full article

This work explicitly demonstrates a semi-analytical effective index approximation (EIA) approach for the description of the propagation properties of rib and ridge waveguides. By using the example of waveguides realized on a low-cost silica-titania (SiO₂:TiO₂) technological platform, we present that EIA may be successfully applied for the approximate determination of modal effective indices and single mode propagation conditions. All obtained results have been confirmed to be convergent with the finite element method (FEM) simulations at low relative error. Due to the tremendously fast execution time of EIA simulations in comparison with the FEM solver, we believe that the presented approach may be applied in a preliminary step of designing functional blocks in new and existing photonic integrated circuit technologies, which often require complex and multi-parameter calculations. Full article

Quantum dots (QDs), with their exceptional optical properties, have emerged as promising candidates to replace traditional phosphors in lighting and display technologies. This study delves into the integration strategies of QDs within glass and polymer matrices to engineer advanced quantum dot color converters (QDCCs) at the industrial scale for practical applications. To achieve enhancements in the photostability and thermal stability of QDCCs, we explore two distinct approaches: the dispersion of QDs in a hydrophilic glass matrix via a sol–gel process and the incorporation of QDs into a non-polar acrylate monomer to formulate QD/polymer nanocomposites. This research further investigates the optical behaviors of these composites, focusing on their light-scattering and propagation mechanisms, which are critical for optimizing light extraction efficiency in QDCCs. Additional optical film and light-scattering particles can improve color conversion efficiency by ~140%. These advancements present a significant step forward in the development of high-performance, energy-efficient, QD-based lighting and display systems. Full article

The analysis reported in this paper shows that the homogeneous sensitivity of both fundamental rib waveguide modes, HE₀₀ and EH₀₀, can slightly exceed the sensitivity of the optimized parent slab waveguide. The most crucial difference in the behavior of these two polarizations is that the sensitivity of the HE₀₀ mode is the maximum for strip waveguides. In contrast, the sensitivity of the EH₀₀ mode can either decrease monotonically or not-monotonically with increasing rib height or behave like a homogeneous sensitivity characteristic of the slab waveguide’s EH₀ mode. The second important conclusion comes from comparing the sensitivity characteristics with the distributions of the fundamental mode’s optical power. Namely, the homogeneous sensitivity of the rib waveguide is at the maximum if, due to a slight variance in the cover refractive index, a variation in the weighted optical power carried by the mode is the maximum. Full article

Environmental pollution remains one of the most challenging problems facing society worldwide. Much of the problem has been caused by human activities and increased usage of various useful chemical agents that inadvertently find their way into the environment. Triclosan (TCS) and related phenolic compounds and derivatives belong to one class of such chemical agents. In this work, we provide a mini review of these emerging pollutants and an outlook on the state-of-the-art in nanostructured adsorbents and photocatalysts, especially nanostructured materials, that are being developed to address the problems associated with these environmental pollutants worldwide. Of note, the unique properties, structures, and compositions of mesoporous nanomaterials for the removal and decontamination of phenolic compounds and derivatives are discussed. These materials have a great ability to scavenge, adsorb, and even photocatalyze the decomposition of these compounds to mitigate/prevent their possible harmful effects on the environment. By designing and synthesizing them using silica and titania, which are easier to produce, effective adsorbents and photocatalysts that can mitigate the problems caused by TCS and its related phenolic derivatives in the environment could be fabricated. These topics, along with the authors’ remarks, are also discussed in this review. Full article