Search Results (9)

The development and research of physically superior multi-principal element alloy (MPEA) binders as cemented carbide binders is a hot topic. In this work, we fabricated a new type of MPEA binder-cemented carbide using the powder metallurgy method and investigated the effects of ball milling parameters and sintering temperature on the microstructure and mechanical properties of the cemented carbide. The results are compared with those of cobalt binder samples under the same conditions. The results show that the ball milling parameters for low-speed long ball milling time are superior to those for high-speed low ball milling time. Compared with the pure cobalt binder, MPEA binder-cemented carbide significantly slows down the growth of WC grains, improves the mechanical properties of cemented carbide, and achieves a combination of TRS of 2741.5 MPa and Rockwell hardness of 91.1 HRA. The multi-principal element alloy (MPEA) binder has the potential to become an excellent substitute for Co. Full article

In this study, an AlCoCrFeNi HEA coating with a 10% mass fraction of WC particles was fabricated on the surface of 316L stainless steel by laser cladding technology. WC powders were formed by the partial or total dissolution of the initial WC particles with different sizes in the AlCoCrFeNi HEA coating. Micron WC particles were dispersed in the coating homogeneously, and millimeter WC particles were deposited on the bottom of coating because of their high density. The addition of the WC powers prompted Columnar dendritic and cellular grains, observed in the bottom and top regions of the coating, respectively. Additionally, this led to a higher micro-hardness and better corrosion resistance than that of the pure HEA coating. Full article

The paper presents results of investigations on the binderless nanostructured tungsten carbide (WC) cutting tools fabrication and performance. The scientific novelty includes the description of some regularities of the powder consolidation under electric current and the subsequent possibility to utilize them for practical use in the fabrication of cutting tools. The sintering process of WC nanopowder was performed with the electroconsolidation method, which is a modification of spark plasma sintering (SPS). Its advantages include low temperatures and short sintering time which allows retaining nanosize grains of ca. 70 nm, close to the original particle size of the starting powder. In respect to the application of the cutting tools, pure WC nanostructure resulted in a smaller cutting edge radius providing a higher quality of TiC/Fe machined surface. In the range of cutting speeds, v_c = 15–40 m/min the durability of the inserts was 75% of that achieved by cubic boron nitride ones, and more than two times better than that of WC-Co cutting tools. In additional tests of machining 13CrMo4 material at an elevated cutting speed of v_c = 100 m/min, binderless nWC inserts worked almost three times longer than WC-Co composites. Full article

The spark plasma sintering (SPS) method is of great interest to the powder and powder metallurgy industry and material researchers of academia for both product manufacturing and advanced material research and development. Today in Japan, a number of SPS products for different industries have already been realized. Today’s fifth-generation SPS systems are capable of producing parts of increasing size, offering improved functionality, reproducibility, productivity, and cost. For instance, pure nano-Tungsten Carbide WC powder (no additives) is fully densified with a nano-grain-sized structure for glass lens application in the optics industry. The SPS is now moving from scientific academia and/or R&D proto-type materials level usage to practical industry use product stage utilizing in the field of electronics, automotive, mold and die, cutting tools, fine ceramics, clean energy, biomaterials industries, and others. This paper reviews and introduces the peculiar phenomenon of SPS and the progress of SPS technology, method, development of SPS systems, and its industrial product applications. Full article

The aim of the research was to disclose the performance of ceramic-metal composites, in particular TiC-based cermets and WC-Co hardmetals, as tool materials for friction stir welding (FSW) of aluminium alloys, stainless steels and copper. The model tests were used to study the wear of tools during cutting of metallic workpiece materials. The primary focus was on the performance and degradation mechanism of tool materials during testing under conditions simulating the FSW process, in particular the welding process temperature. Carbide composites were produced using a common press-and-sinter powder metallurgy technique. The model tests were performed on a universal lathe at the cutting speeds enabling cutting temperatures comparable the temperatures of the FSW of aluminium alloys, stainless steels and pure copper. The wear rate of tools was evaluated as the shortening of the length of the cutting tool nose tip and reaction diffusion tests were performed for better understanding of the diffusion-controlled processes during tool degradation (wear). It was concluded that cermets, in particular TiC-NiMo with 75–80 wt.% TiC, show the highest performance in tests with counterparts from aluminium alloy and austenitic stainless steel. On the other hand, in the model tests with copper workpiece, WC-Co hardmetals, in particular composites with 90–94 wt.% WC, outperform most of TiC-based cermet, including TiC-NiMo. Tools from ceramic-metal composites wear most commonly by mechanisms based on adhesion and diffusion. Full article

Aluminum and aluminum alloys have the advantage of a high strength-to-weight ratio, but their low hardness and poor wear resistance often cause wear damage. In the present study, the cladding layer was prepared using argon-shielded arc cladding of CuZn40-WC powders which were pre-coated on a pure aluminum substrate. The effects of WC proportion on the morphology, microstructure, and properties of cladding layers were investigated in detail. The results indicated that the optimal WC proportion in CuZn40-WC powders was 60 wt.%. With the increase of WC proportion, although the morphology of the cladding layer became slightly worse, the surface quality of the cladding layer was acceptable for industrial application until the WC proportion was 80 wt.%. Meanwhile, the top width and maximum depth of the cladding layer decreased. The maximum microhardness and optimal wear resistance of the cladding layer were 4.5 and 2.5 times that of the aluminum substrate, respectively. The increased microhardness and wear resistance were mainly attributed to the formation of Al₄W in the cladding layer. The wear scar of the high wear resistance specimen was smoother and some bulk Al₄W compounds were clearly observed on the wear surface. Full article

In this study, the laser metal deposition (LMD) of the Inconel 625–tungsten carbide (WC) metal matrix composite was investigated. The composite coating was deposited on Inconel 625 substrate by powder method. A powder mixture containing 10 wt% of WC (5 µm) was prepared by wet mixing with dextrin binder. Coating samples obtained by low-power LMD were pore- and crack-free. Ceramic reinforcement was distributed homogenously in the whole volume of the material. Topologically close-packed (TCP) phases were formed at grain boundaries between WC and Inconel 625 matrix as a result of partial dissolution of WC in a nickel-based alloy. Line analysis of the elements revealed very small interference of the coating in the substrate material when compared to conventional coating methods. The average Vickers hardness of the coating was about 25% higher than the hardness of pure Inconel 625 reference samples. Full article

Near-net shape forming of metallic components from metallic powders produced in situ from reduction of corresponding pure metal oxides has not been explored to a large extent. Such a process can be probably termed in short as the “Reduction-Sintering” process. This methodology can be especially effective in producing components containing refractory metals. Additionally, in situ production of metallic powder from complex oxides containing more than one metallic element may result in in situ alloying during reduction, possibly at lower temperatures. With this motivation, in situ reduction of complex oxides mixtures containing more than one metallic element has been investigated intensively over a period of years in the department of materials science, KTH, Sweden. This review highlights the most important features of that investigation. The investigation includes not only synthesis of intermetallics and refractory metals using the gas solid reaction route but also study the reaction kinetics and mechanism. Environmentally friendly gases like H₂, CH₄ and N₂ were used for simultaneous reduction, carburization and nitridation, respectively. Different techniques have been utilized. A thermogravimetric analyzer was used to accurately control the process conditions and obtain reaction kinetics. The fluidized bed technique has been utilized to study the possibility of bulk production of intermetallics compared to milligrams in TGA. Carburization and nitridation of nascent formed intermetallics were successfully carried out. A novel method based on material thermal property was explored to track the reaction progress and estimate the reaction kinetics. This method implies the dynamic measure of thermal diffusivity using laser flash method. These efforts end up with a successful preparation of nanograined intermetallics like Fe-Mo and Ni-W. In addition, it ends up with simultaneous reduction and synthesis of Ni-WN and Ni-WC from their oxide mixtures in single step. Full article

The Al-alloying treated tungsten carbide (WC)-Co tool was subjected to grinding using a jaw crusher and planetary mill followed by three wet chemical treatment steps to establish an effective recycling process for WC scraps, especially those generated as bulky and hard scrap. This alloyed WC tool was readily ground to a powder of 1 mm or less and divided into two portions that were 150 µm in size. The wet chemical treatments enabled us to recover W to 69.44% from the under-sized 150 µm and also obtain WC powders from the over-sized 150 µm with a high purity of 98.9% or more. Full article