Search Results (15)

The building sector plays a key role in the transition toward climate neutrality, with national regulations across the EU requiring the construction of nearly zero-energy buildings (nZEBs). However, while energy performance has been extensively studied, less attention has been given to the problem of ensuring user comfort—both indoors and in the surrounding outdoor areas—under nZEB design constraints. This gap raises two key research objectives: (1) to evaluate whether a well-designed nZEB with extensive glazing maintains acceptable indoor thermal comfort and (2) to assess whether residents experience greater outdoor thermal comfort and satisfaction in small, sun-exposed private gardens or in larger, shaded communal green spaces. To address these objectives, a newly built residential estate near Kraków (Poland) was analyzed. The investigation included simulation-based assessments during the design phase and in situ measurements during building operation, complemented by a user survey on spatial preferences. Indoor comfort was evaluated for rooms with large glazed façades, as well as rooms with standard-sized windows, while outdoor comfort was assessed in both private gardens and a shared green courtyard. Results show that shading the southwest-oriented glazed façade with an overhanging terrace provided slightly lower temperatures in ground-floor rooms compared to rooms with standard unshaded windows. Outdoors, users experienced lower thermal comfort in small, unshaded gardens than in the larger, vegetated communal area (pocket park), which demonstrated greater capacity for temperature moderation and thermal stress reduction. Survey responses further indicate that potential future residents prefer the inclusion of a shared green–blue infrastructure area, even at the expense of building some housing units in semi-detached form, instead of maximizing the number of detached units with unshaded individual gardens. These findings emphasize the importance of addressing both indoor and outdoor comfort in residential nZEB design, showing that technological efficiency must be complemented by user-centered design strategies. This integrated approach can improve the well-being of residents while supporting climate change adaptation in the built environment. Full article

This paper presents a multi-constraint topology optimization strategy for rudder structures, integrating additive manufacturing (AM)-related overhang angle and flutter-performance considerations. To the best of our knowledge, this is the first study to couple AM overhang control with mass center (flutter) steering in a single density-based formulation for flight control rudder structures. The approach incorporates constraints on structural volume fraction, overhang angle for AM, and mass center positioning to address multi-function design objectives—structural lightweighting, stiffness, aerodynamic stability, and manufacturability. A build-direction-aware projection filter and a smooth Heaviside mass center constraint are introduced to enforce these requirements during every optimization iteration. The resulting layout converges to a sandwich-type rudder with balanced mechanical performance and AM feasibility. Simulation results show that enforcing overhang constraints reduces support material usage by 46.9% and residual deformation by 14.2%, significantly enhancing AM feasibility. Additionally, introducing center-of-mass constraints improves flutter velocity from 3327 m s⁻¹ to 3759 m s⁻¹, indicating a 6.84% increase over conventional optimization and demonstrating improved dynamic stability. These simultaneous gains in manufacturability and aeroelastic safety, achieved without post-processing, underline the novelty and practical value of the proposed constraint set. The strategy thus offers a practical and efficient design method for high-performance, AM-friendly rudder structures with superior mechanical and aerodynamic characteristics, and it can be readily extended to other mission-critical AM components. Full article

This paper presents a comprehensive design approach for optimizing the pole configuration of a coaxial magnetic gear (CMG) structure with an overhang to enhance torque characteristics. Five CMG models were designed, and their characteristics were analyzed. A three-dimensional finite element method analysis was conducted to account for axial leakage flux. To efficiently explore the design space, we utilized an optimal Latin hypercube sampling method to generate experimental points and constructed a kriging-based metamodel owing to its low root-mean-square error. We analyzed torque characteristics across the design variables to identify characteristic trends and performed a parametric sensitivity analysis to evaluate the influence of each variable on the torque. We derived an optimal solution that satisfied the objective function and constraints using the design variables. The characteristics of the proposed model were validated through electromagnetic field analysis, fast Fourier transform analysis of the air-gap magnetic flux density, and structural analysis. The optimal model achieved an average torque of 61.75 Nm, representing a 21.15% improvement over the initial model, while simultaneously reducing the ripple factor by 0.41%. These findings indicate that the proposed CMG design with an overhang effectively enhances torque characteristics. Full article

This study examines the combination of overhang constraints and Reliability-Based Topology Optimization (RBTO) in additive manufacturing (AM). AM offers intricate component production but faces challenges due to support structures. Incorporating overhang constraints in topology optimization enables self-supporting structures. RBTO addresses uncertainties in design variables to enhance reliability. This research investigates build direction parameter solutions using deterministic and RBTO algorithms. Topological properties, compliance, sensitivity, and density filters are assessed, alongside optimization techniques like Method of Moving Asymptotes (MMA) criterion and Optimality Criteria (OC). In numerical experiments on the MBB beam, the AM-RBTO algorithm reduced 3D printing time by approximately 18.3% and improved structural performance by lowering the objective function value by 1.85% compared to conventional RBTO. Results contribute to merging overhang constraints and RBTO in AM topology optimization, improving design by considering uncertainties. The study enhances computational efficiency and stability in optimizing build direction parameters, offering valuable insights for future AM applications. Full article

This study introduced a systematic framework to develop practical design guidelines specifically for filament-based material extrusion of metals (MEX/M), an additive manufacturing (AM) process defined by ISO/ASTM 52900. MEX/M provides a cost-efficient alternative to conventional manufacturing methods, which is particularly valuable for rapid prototyping. Although AM offers significant design flexibility, the MEX/M process imposes distinct geometric and process constraints requiring targeted optimization. The research formulates and validates design guidelines tailored for the MEX/M using an austenitic steel 316L (1.4404) alloy filament. The feedstock consists of a uniform blend of 316L stainless steel powder and polymeric binder embedded within a thermoplastic matrix, extruded and deposited layer by layer. Benchmark parts were fabricated to examine geometric feasibility, such as minimum printable wall thickness, feature inclination angles, borehole precision, overhang stability, and achievable resolution of horizontal and vertical gaps. After fabrication, the as-built (green-state) components undergo a two-step thermal post-processing treatment involving binder removal (debinding), followed by sintering at elevated temperatures to reach densification. Geometric accuracy was quantitatively assessed through a 3D scan by comparing the manufactured parts to their original CAD models, allowing the identification of deformation patterns and shrinkage rates. Finally, the practical utility of the developed guidelines was demonstrated by successfully manufacturing an impeller designed according to the established geometric constraints. These design guidelines apply specifically to the machine and filament type utilized in this study. Full article

Qinghai Province urgently requires the development of adaptive energy-efficient rural housing construction to address resettlement needs arising from hydropower projects, given the region’s characteristic combination of high solar irradiance resources and severe cold climate conditions. This research establishes localized retrofit strategies through systematic field investigations and Rhinoceros modeling simulations of five representative rural residences across four villages. The key findings reveal that comprehensive building envelope retrofits achieve an 80% reduction in energy consumption. South-facing sunspaces demonstrate effective thermal buffering capacity, though their spatial depth exhibits negligible correlation with heating energy requirements. An optimized hybrid shading system combining roof overhangs and vertical louvers demonstrates critical efficacy in summer overheating mitigation, with vertical louvers demonstrating superior thermal and luminous regulation precision. Architectural orientation analysis identifies an optimal alignment within ±10° of true south, emphasizing the functional zoning principle of positioning primary living spaces in south-oriented ground floor areas while locating auxiliary functions in northeastern/northwestern zones. The integrated design framework synergizes three core components: passive solar optimization, climate-responsive shading mechanisms, and performance-enhanced envelope systems, achieving simultaneous improvements in energy efficiency and thermal comfort within resettlement housing constraints. This methodology establishes a replicable paradigm for climate-resilient rural architecture in high-altitude, solar-intensive cold regions, effectively reconciling community reconstruction needs with low-carbon development imperatives through context-specific technical solutions. Full article

With the emergence of additive manufacturing technology, patient-specific cranial implants using 3D printing have massively influenced the field. These implants offer improved surgical outcomes and aesthetic preservation. However, as additive manufacturing in cranial implants is still emerging, ongoing research is investigating their reliability and sustainability. The long-term biomechanical performance of these implants is critically influenced by factors such as implant material, anticipated loads, implant-skull interface geometry, and structural constraints, among others. The efficacy of cranial implants involves an intricate interplay of these factors, with fixation playing a pivotal role. This study addresses two critical concerns: determining the ideal number of fixation points for cranial implants and the optimal curvilinear distance between those points, thereby establishing a minimum threshold. Employing finite element analysis, the research incorporates variables such as implant shapes, sizes, materials, the number of fixation points, and their relative positions. The study reveals that the optimal number of fixation points ranges from four to five, accounting for defect size and shape. Moreover, the optimal curvilinear distance between two screws is approximately 40 mm for smaller implants and 60 mm for larger implants. Optimal fixation placement away from the center mitigates higher deflection due to overhangs. Notably, a symmetric screw orientation reduces deflection, enhancing implant stability. The findings offer crucial insights into optimizing fixation strategies for cranial implants, thereby aiding surgical decision-making guidelines. Full article

To analyze the impact of different objective functions and additive manufacturing (AM) constraints on structural topology optimization, it is necessary to perform an in-depth comparative study. This analysis should consider specific structural design factors, such as compliance, volume, or stress minimization, and assess their effects on the topology optimization for AM. In addition, the inclusion of AM constraints can have a significant influence on various aspects, including optimal part geometry, part volume, support structure volume, and structural performance. Thus, it is essential to investigate and compare these factors to determine the optimal part design for AM. This study focuses on comparing topology optimization results obtained using compliance, stress, or multi-objective minimization, with and without AM constraints. A comparative analysis was conducted in the study, utilizing three structural design examples: cantilever beam, bridge-shaped structure, and L-shaped beam. The comparison results provide insights into the effects of build orientation, AM constraints such as overhang, and different design objectives on the structural topology optimization for AM. Full article

In multi-axis fused deposition modeling (FDM) printing systems, support-free curved layer fabrication is realized by continuous transition of the printer nozzle orientation. However, the ability to print 3D models with complex geometric (e.g., high overhang) and topological (e.g., high genus) features is often restricted by various manufacturability constraints inherent to a curved layer design process. The crux in a multi-axis printing process planning pipeline is to design feasible curved layers and their tool paths that will satisfy both the support-free condition and other manufacturability constraints (e.g., collision-free). In this paper, we propose a volumetric curved layer decomposition method that strives to not only minimize (if not prevent) collision-inducing local shape features of layers, but also enable adaptive layer thickness to comply with a new volumetric error-based surface quality criterion. Our method computes an optimal Radial Basis Functions (RBF) field to modify the fabrication sequence field, from which, the iso-surface layers are extracted to design the corresponding multi-axis printing tool paths. A method to fine-tune variable nozzle orientations on each resulting curved layer is then proposed to overcome possible collisions in high-genus geometries. To validate the concept and exhibit its potential, several support-free fabrication experiments and comparisons with the conventional geodesic field-based slicing are presented, and the results give a preliminary confirmation of the feasibility and advantages of the proposed method. Full article

Additive manufacturing with the DED-arc process offers limited freedom in terms of the geometric shape of work pieces. The process and fabrication systems restrict the part geometry producible, which must be taken into account during design already. For this reason, a design process was investigated in which geometry generation is based on a self-organizing system. The aim of using a self-organizing system is the possibility to directly control the geometry-defining points. Next to load cases, the design method considers geometric boundary conditions from the production process when generating the geometry. In order to identify these geometrical constraints from production experimentally, a concept of Case Study Demonstrators was applied. This was used to investigate how path planning and production can be carried out for specific geometrical features and to identify restraints of the process and the manufacturing system, e.g., smallest producible wall thickness and overhangs. Subsequently, the obtained restraints were considered as boundary conditions for the design process and were included in the modification of an example geometry. By applying the presented design method, it was possible to maintain a minimum wall thickness throughout the structure while generating a topologically optimized geometry. In contrast to compliance with the minimum wall thickness, no satisfactory behavioral rule could be found for limiting the overhang. Full article

Permanent magnet synchronous machines (PMSMs) with an overhang structure can increase power density by compensating for the increased magnetic energy of permanent magnets. To analyze the overhang structure, a three-dimensional (3D) analysis of PMSMs is essential. However, 3D analysis takes a long time and the modeling process is complicated in the initial design stage. To overcome these problems, a magnetic equivalent circuit technique is applied to the 2D model. In this paper, an optimal design method for PMSMs with an overhang structure is proposed based on the semi 3D magnetic equivalent circuit (MEC) and random walk method. By using semi 3D MEC, it is possible to quickly analyze PMSM and obtain accurate electromagnetic analysis results considering the overhang effect. Moreover, the volume and weight of PMSM can be minimized by optimizing the rotor’s four design parameters using a random walk algorithm. To obtain high efficiency, the objective function is selected so that copper loss is minimized under the same constraints. The validity of the proposed design technique is verified by comparing the analysis results of semi 3D MEC and 3D finite element method for the derived optimal model. Full article

Although additive manufacturing (AM) enables designers to develop products with a high degree of design freedom, the manufacturing constraints of AM restrict design freedom. One of the key manufacturing constraints is the use of support structures for overhang features, which are indispensable in AM processes, but increase material consumption, manufacturing costs, and build time. Therefore, controlling support structure generation is a significant issue in fabricating functional products directly using AM. The goal of this paper is to propose a knowledge-based design algorithm for reducing support structures whilst considering printability and as-printed quality. The proposed method consists of three steps: (1) AM ontology development, for characterizing a target AM process, (2) Surrogate model construction, for quantifying the impact of the AM parameters on as-printed quality, (3) Design and process modification, for reducing support structures and optimizing the AM parameters. The significance of the proposed method is to not only optimize process parameters, but to also control local geometric features for a better surface roughness and build time reduction. To validate the proposed algorithm, case studies with curve-based (1D), surface-based (2D), and volume (3D) models were carried out to prove the reduction of support generation and build time while maintaining surface quality. Full article

Metal powder bed-based Additive Manufacturing (AM) technologies, such as Electron Beam-Melting (EBM) and Laser Powder Bed Fusion (LPBF), are established in several industries due to the large design freedom and mechanical properties. While EBM and LPBF have similar operating steps, process-specific characteristics influence the component design. The differences in the energy coupling lead to differing solidification conditions, microstructures, and, thus, mechanical properties. The surface finish and geometrical accuracy are also affected. As opposed to LPBF, EBM powder layers are preheated prior to selective melting. In this study, similar volume energy densities in LPBF and EBM were used to manufacture Ti6Al4V test geometries to assess the process transferability. Since the energy coupling of LPBF and EBM differ, heat source absorption was considered when calculating the volume energy density. Even when a similar volume energy density was used, significant differences in the component quality were found in this study due to specific respective process constraints. The extent of these constrains was investigated on voluminous samples and support-free overhanging structures. Overhang angles up to 90° were manufactured with LPBF and EBM, and characterized with regard to the relative density, surface roughness, and geometric compliance. Full article

This paper investigates the impact of the wire selection on the performance of induction motors for automotive applications. The section of wire and the material are evaluated at a high speed of 200 kW in an induction motor designed for premium vehicle applications. The proposed solutions have the same electromagnetic and thermal constraints, as well as the same final encumbrance. The various wire and winding types differ in terms of slot design, phase resistance, end-winding overhanging portion, skin and proximity effects, and equivalent slot thermal conductivity. Their impacts are analyzed in terms of the operating area motor efficiency and they are tested in an automotive drive cycle, highlighting the advantages and disadvantages of each configuration. Full article

The potential of Additive Manufacturing (AM) is high, with a whole new set of manufactured parts with unseen complexity being offered. However, the process has limitations, and for the sake of economic competitiveness, these should also be considered. Therefore, a computational methodology, capable of including the referenced limitations and providing initial solid designs for Selective Laser Melting (SLM) is the subject of the present work. The combination of Topology Optimization (TO) with the simplified fabrication model is the selected methodology. Its formulation, implementation, and integration on the classic TO algorithm is briefly discussed, being capable of addressing the minimum feature size and the overhang constraint limitations. Moreover, the performance and numerical stability of the methodology is evaluated, and numerical variables, such as the accuracy of structural equilibrium equations and the material interpolation model, are considered. A comparative study between these variables is presented. The paper then proposes an enhanced version of the selected methodology, with a better convergence towards a discrete solution. Full article