Search Results (16,115)

The conducted study was focused on the development of a new type of polymer blends intended for additive manufacturing applications, in particular, the material extrusion method (MEX). The developed materials were prepared from recycled poly(ethylene terephthalate) and amorphous copolymers poly(ethylene terephthalate-glycol) (PETG), and poly(cyclohexylenedimethyl terephthalate-glycol) (PCTG). The basic blend systems were additionally modified with POE-g-GMA impact modifier (IM) during the reactive extrusion process. The main aim of the work was to assess the effectiveness of using composite additives and their influence on the mechanical and thermomechanical parameters of the tested systems. To prepare the composites, selected polymer blends were modified with 10% of talc (T) and carbon fibers (CF). The properties evaluation includes the mechanical/thermomechanical testing, thermal analysis and structural observations. The accuracy of printing was measured using optical scanning methods. The test results indicate that even the relatively small amount of the CF filler could lead to a significant increase in tensile modulus from reference 1.6 GPa to 2.9 GPa; the same improvement applies to strength values, where the CF-modified materials reached 45 MPa, compared to the reference 31 MPa. The heat deflection tests (0.455 MPa) after annealing revealed the maximum HDT of around 170 °C for both types of CF-modified materials. The Vicat test results were also favorable for annealed materials. Considering that the Vicat/HDT results after the 3D-printing process usually reach around 70 °C, the performed heat treatment strongly enhanced the heat resistance for most of the prepared blends. The performed studies revealed that for most of the prepared materials, the brittleness was a common drawback for both MEX-printed and injection-molded materials. Full article

The present work aims to investigate the microstructure and mechanical properties of laser beam spot welds in the superalloy Nimonic 80 A. Considering the importance of this innovative process in the manufacturing of engineering components for high-security industries, it is necessary to study the influence of the welding thermal cycle on the microstructure and mechanical properties of welded joints. The rapid heating/cooling, melting, and re-solidification phenomena that occur during welding modify the metallurgical characteristics of the weld compared with the microstructure of the base metal. Because the energy density is high and the process duration is very short, the microstructure obtained after solidification is fine dendritic in the central area of the joint and columnar in the weld–base metal transition zone. For the same reasons, the heat-affected zone (HAZ) is slightly extended. The increase in the size of the crystalline grains in the HAZ is negligible due to the low diffusivity of the nickel-based γ solid solution matrix, which inhibits the rapid migration of grain boundaries during the welding process. Metallographic analyses were performed using optical microscopy and scanning electron microscopy. The microhardness values, 152–168 HV0.05 in the weld and 180–190 HV0.05 in the base metal, together with the tensile–shear strength values (760–780 N/mm²) obtained at room temperature, demonstrate that the proposed welding process is appropriate and feasible for engineering applications involving Nimonic 80A superalloys. Full article

Over the past two decades, organic semiconductors have attracted significant research interest due to their advantageous features, including low-cost fabrication, lightweight properties, and portability, for photonic device applications. In this study, nickel sulfide doped with cobalt $(\mathrm{N}\mathrm{i}\mathrm{S}/\mathrm{C}\mathrm{o})$ nanocomposites were successfully synthesized via a wet-chemical processing technique and used as a dopant in the active layer of thin-film organic solar cells (TFOSCs). The poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PC61BM) blend was used as the active layer in this investigation. The devices were fabricated with $\mathrm{N}\mathrm{i}\mathrm{S}/\mathrm{C}\mathrm{o}$ nanocomposites at 1 wt%, 2 wt%, and 3 wt% in the active layer to determine the optimal dopant concentration. However, the experimental evidence clearly showed that the solar cell’s performance depends on the concentration of the $\mathrm{N}\mathrm{i}\mathrm{S}/\mathrm{C}\mathrm{o}$ nanocomposites. As a result, the highest power conversion efficiency (PCE) recorded in this experimental work was 6.11% at a 1% doping concentration, compared with 2.48% for the pristine reference device under AM 1.5G illumination (100 mW/cm²) in ambient conditions. The optical and electrical properties of the active layers are found to be strongly influenced by the inclusion of $\mathrm{N}\mathrm{i}\mathrm{S}/\mathrm{C}\mathrm{o}$ nanocomposites in the medium. However, the device doped with 1 wt% $\mathrm{N}\mathrm{i}\mathrm{S}/\mathrm{C}\mathrm{o}$ nanocomposite exhibits the highest absorption intensity, consistent with the better performance observed in this study, which can be attributed to the localized surface plasmon resonance (LSPR) effect. The optical and morphological characteristics of the synthesized $\mathrm{N}\mathrm{i}\mathrm{S}/\mathrm{C}\mathrm{o}$ nanocomposites were comprehensively analyzed using high-resolution transmission electron microscopy (HRTEM), high-resolution scanning electron microscopy (HRSEM), and additional complementary techniques. Full article

This study systematically investigated the characterization of 2Fe-CDs/12Mn-CeO₂ composites and the colorimetric sensing properties of H₂O₂, glucose (Glu), and glutathione (GSH). The morphology, structure, and optical properties of the 2Fe-CDs/12Mn-CeO₂ composite were analyzed in detail by XRD, FT-IR, SEM, TEM, XPS, and Raman spectroscopy, and its formation was supported by multiple complementary characterization techniques. The catalytic efficiency (kcat/Km) of the nanozyme is 152-fold higher than natural HRP under optimal conditions and remains 59-fold higher even after temperature normalization to 25 °C. In the colorimetric sensing experiments, the detection limits of Fe-CDs/Mn-CeO₂ were 0.21 μM, 2.7 μM, and 0.63 μM for H₂O₂, Glu, and GSH, respectively. Rapid and accurate determination of the concentrations of these biomolecules can be achieved by observing the color changes after Fe-CDs/Mn-CeO₂ reaction with the objects to be measured. The experimental results show that Fe-CDs/Mn-CeO₂ have high sensitivity and selectivity for H₂O₂, Glu, and GSH, which provides a solid theoretical and experimental basis for the application of Fe-CDs/Mn-CeO₂ in the field of biosensing and medical diagnosis. Full article

Epoxy resin (E-51) exhibits excellent adhesion and is widely used in the preparation of functional composite coatings. However, its smooth surface lacking micro/nano composite structures limits its self-cleaning capability and optical properties. Direct incorporation of organic silicone or inorganic fillers often faces severe phase separation and filler agglomeration issues, resulting in defects in coating durability and weather resistance. To address these challenges, this study developed a synergistic modification strategy integrating surface energy modulation with the architectural design of micro/nano-structures. Amino-terminated PDMS undergoes ring-opening addition reactions with epoxy groups in the epoxy resin, while functionalized barium sulfate nanoparticles modified with dual silane coupling agents are incorporated to enhance optical properties. This synergistic approach not only resolved interfacial compatibility but also endowed the PDMS@EP-BaSO₄ coating with outstanding comprehensive properties; the water contact angle increased to 123.5°, demonstrating an easy-to-clean benefit. Visible light reflectance reached 95%, and emissivity rose to 90%. Furthermore, when applied to metal surfaces, the coating exhibited excellent stability against acid–alkali–salt corrosion, extreme temperatures, and ultrasonic agitation. This work provided a novel approach for developing protective coatings that integrated high reflectance, high emissivity, and long-term anti-soiling properties. Full article

This study analyses the influence of yarn composition and knitted macrostructure on the structural and functional performance of passive smart knitted fabrics with optical functionalities. Twelve knitted macrostructures were produced using folded composite yarns combining cotton, reflective, and photoluminescent components and different stitch patterns. Thickness, air permeability, and reflectance under UV and visible illumination were experimentally evaluated. The results indicate that knitted macrostructure primarily controls thickness and air permeability, whereas optical response is governed by yarn composition. Variations in stitch pattern enable regulation of air permeability independent of optical behaviour, while UV-responsive yarn components dominate reflectance performance. The findings support independent optimisation of structural and optical properties through combined yarn and macrostructural design. Full article

Nickel-oxide-based anodic electrochromic materials are extensively utilized as counter electrodes in smart window systems due to their reversible optical response during ion insertion and extraction. This study systematically investigates the influence of substrate temperature on the electrochromic properties of sputtered nickel-tungsten oxide thin films. The deposited thin films exhibit an amorphous structure. An increase in substrate temperature results in a decrease in nickel-vacancy concentration. Raman spectroscopy verifies the amorphous nature. Films deposited at lower substrate temperatures exhibit superior electrochromic performance, characterized by improved optical contrast of 64% and rapid coloration (2.21 s) and bleaching (0.93 s) dynamics. The enhanced performance is ascribed to the disordered amorphous structure and the existence of enough nickel vacancies, which collectively facilitate efficient and reversible lithium-ion transfer. This study illustrates that meticulous regulation of substrate temperature is an effective method for adjusting the microstructure and defect chemistry of nickel–tungsten oxide thin films, rendering them appropriate as effective counter electrodes for energy-efficient smart window applications. Full article

In this study, rice-husk fiber (RHF) extracted via alkali hydrolysis was used as a reinforcing material (0–10 wt%) in a pectin-sodium alginate (PE/SA) matrix to develop biofilms by the casting method. These biofilms were characterized by using FTIR, XRD, TGA, and DSC. The thickness, moisture content, water solubility, swelling behavior, water-contact angle, water-vapor permeability, optical transparency, and mechanical properties of biofilms were investigated. It was observed that the PE/SA/RHF film loaded with 5% RHF had better visual attributes, and a further increase in reinforcement was not found to be as favorable. The addition of 10 wt% RHF significantly enhanced the thickness from 0.094 to 0.127 mm, water solubility from 49.25 to 56.13%, water-contact angle from 48.4 to 62.6°, and tensile strength from 4.17 to 10.23 MPa. However, decreases in water-vapor permeability from 1.94 × 10⁻⁹ to 1.32 × 10⁻⁹ g·m⁻¹·Pa⁻¹·s⁻¹ and in elongation at break from 19.24 to 2.87% were observed in the biofilms. Structurally, FTIR confirmed intermolecular hydrogen bonding between components. XRD revealed that the films remained predominantly amorphous, without significant crystalline alterations. Furthermore, thermal stability improved with the addition of RHF. Finally, these PE/SA/RHF composite films may be potential eco-friendly biodegradable packaging candidates for food industry applications. Full article

The full symmetry group is found for a system of nonlinear schrödinger equations describing the propagation of optical pulses in an isotropic media. It is shown, in particular, that the six-dimensional symmetry group found is composed of a scaling transformation and a rotation of the four-dimensional space, thereby proving that the symmetry group preserves the shape of solutions. A symmetry classification of one-dimensional subalgebras of the Lie algebra is performed and yields, in particular, the symmetry reduction to the most general system of equations satisfied by the solitary waves of the equation. Explicit soliton solutions of the equation are found by largely autonomous technics. The found solitons are used to recursively generate two new ones by means of two iterations using the symmetry group. Other properties of the system are also highlighted, as well as the possible connections between the theories of symmetry groups and Darboux transformations inspired by this study. Full article

CAD/CAM polymer-based dental materials are increasingly used as metal-free alternatives for fixed and implant-supported restorations. High-performance polymers such as polyetheretherketone (PEEK), fiber-reinforced composites, and graphene-reinforced polymers have been introduced to improve material stability; however, evidence regarding the effects of thermal aging on their physicochemical and biological properties remains limited. In this study, PEEK, a fiber-reinforced composite (FRC), and a graphene-reinforced PMMA-based polymer (G-CAM) were evaluated. Twenty-seven disc-shaped specimens (10 × 2 mm; n = 9 per material) were fabricated and subjected to 10,000 thermal cycles between 5 and 55 °C. Color change (ΔE₀₀), surface roughness (Ra), and Vickers microhardness (VHN) were measured before and after aging. Chemical stability was assessed using FTIR and Raman spectroscopy, surface morphology by SEM analysis, and biological safety by cytotoxicity testing. Material-dependent differences were observed in color stability, surface roughness, and microhardness after thermal aging (p < 0.05). Microhardness decreased in the fiber-reinforced and graphene-reinforced materials, whereas PEEK showed no significant change. Spectroscopic analyses indicated preserved chemical structure, and all materials demonstrated acceptable cytocompatibility. Thermal aging influenced material behavior while chemical stability and biological safety were maintained, highlighting the importance of considering aging behavior during material selection for prosthetic restorations. Full article

Mechanochromism is a phenomenon in which mechanical stimuli change the optical properties of a material, such as its color and emission properties. Various materials exhibiting this behavior have been intensively studied. Mechanochromic materials that exploit liquid crystals have been previously reported. Using liquid crystals, properties different from those of conventional materials, such as anisotropic response and multicolored luminescence due to intermediate aggregation phase stabilization, can be expected. Recently, we reported the preparation and evaluation of the optical properties of liquid-crystalline mechanochromic dyes with cholesterol terminals. The dyes formed gels in some solvents, changed their emission color, and exhibited a friable response without reaching a crystalline state. In addition, film-forming properties, processability, and responsiveness were improved in thin films mixed with polymers. However, the mechanical and thermal stabilities of the gels were low. In this study, a compound similar to the polymerizable unit was synthesized to produce tougher gels. In addition, triblock polymers with a mechanoresponsive dye in the hard segment were synthesized. The xerogel film prepared from the monomer showed an irreversible blue shift in photoluminescent color by mechanical grinding and also exhibited linearly polarized photoluminescence by uniaxial grinding due to force-induced alignment. On the other hand, the xerogel film prepared from the triblock copolymer showed a blue shift in photoluminescent color that can approximately revert to the initial state by thermal annealing, though it showed no anisotropy by uniaxial grinding, indicating that polymerization partially preserves mechanical responsiveness. Full article

Traditional soil management in vineyards and olive groves of semi-arid regions relies on repeated tillage, which accelerates soil organic matter (SOM) oxidation and limits long-term carbon storage. In the context of carbon-neutral agricultural strategies, understanding how alternative practices influence SOM stocks, redistribution, and stabilization is essential. We sampled six paired sites in central Spain (three vineyards and three olive groves), each comprising adjacent plots under conventional tillage or continuous cover cropping, at 0–10 and 10–30 cm depths. We analyzed water-extractable organic carbon (WEOC), optical properties of water-extractable organic matter (WEOM; specific UV absorbance at 254 nm (SUVA₂₅₄) and the absorbance ratio E4/E6), β-glucosidase activity, and the SOC/clay ratio as a proxy for mineral-associated SOC stabilization. Depth was the main factor structuring SOC and biological activity, with higher values in the topsoil. Management effects on bulk SOC were limited although cover cropping increased aboveground biomass and influenced WEOC dynamics. Vertical contrasts (30–10 cm) showed a positive association between WEOC and SOC/clay, suggesting that increased WEOC at depth co-varies with stabilization potential. Partial least squares analysis for 10–30 cm showed that SOC/clay was associated with WEOC, E4/E6, and β-glucosidase activity. These results suggest that subsoil carbon stabilization in semi-arid conditions may be linked to DOC availability and microbial processing rather than directly to surface biomass inputs. Full article

Circularly polarized (CP) organic light-emitting diodes (CP-OLEDs) have attracted considerable attention due to their promising applications in next-generation display systems, optical data transmission, and quantum computing, and their potential roles in medical devices. Achieving efficient and tunable CP emission remains a significant challenge, prompting the development of various strategies that leverage organic semiconductors. Notably, certain classes of materials now consistently deliver CP polarization at levels suitable for technological applications. Among these, conjugated polymers, particularly the copolymer poly(9,9-dialkylfluorene-alt-benzothiadiazole) (PFBT), stand out for their exceptional optoelectronic properties, ease of processing, and adaptability to produce CP emission. PFBT has played diverse roles within CP-OLED devices, enabling innovative architectural solutions. This review explores principal strategies for integrating PFBT into CP-OLED architectures, drawing upon findings from the recent scientific literature. By consolidating current knowledge and identifying unresolved issues, this work aims to inspire further research into the development of solution-processable, high-performance and tunable CP-OLEDs based on PFBT and conjugated polymers in general. Full article

In high-power laser systems, extrinsic impurities—particularly Ce introduced during conventional ring polishing—have been identified as critical contributors to the degradation of laser-induced damage resistance in fused silica optical components. This study systematically investigates the effects of cerium substitutional doping on the electronic structure and optical properties of fused silica, integrating first-principles density functional theory calculations with experimental characterizations. The results demonstrate that substitutional incorporation of cerium atoms into the fused silica framework introduces deep-level defect states within the band gap, resulting in band gap narrowing and absorption edge redshift of the material. The energy position of the defect states depends on the Ce doping configuration. Among them, the Ce-4f orbital constitutes the dominant component of the defect state’s electronic structure, while the neighboring atomic orbitals such as O-2p and Si-3s/3p participate in bonding through hybridization, thereby determining the depth and distribution characteristics of the defect levels. The optical absorption edge of cerium-doped fused silica undergoes a significant redshift from the intrinsic value of 222 nm to 468 nm in the dual-Ce adjacent-site doping configuration, thereby endowing the material with substantial optical absorption capability at a wavelength of 355 nm. μ-UVPL spectroscopy combined with μ-XRD and other characterization analyses confirmed that the characteristic emission peak at 450 nm on the surface region of fused silica originated from Ce-related defect centers; this spectral feature was consistent with the defect state electronic structure predicted by the diatomic nearest-neighbor doping model. LIDT tests further indicated that the Ce-contaminated area significantly weakened the material’s laser damage resistance under 355 nm laser irradiation. This study further explained the mechanism by which traditional polishing-induced Ce element doping causes the low laser damage threshold of fused silica optical components, providing a theoretical basis for improving their performance. Full article

Effects of gastric acid and antiacid medications on the surface and optical properties of resin-based restorative materials were evaluated. A hybrid-CAD/CAM block, a 3D-printed resin, a paste-type composite, and a flowable composite were investigated (n = 9). Samples were prepared (1 mm thickness) and polished. All samples were exposed to gastric acid for 6 days, followed by a second exposure to distilled water, antiacid medication, or gastric acid for 56 min. Surface roughness, translucency, and fluorescence were assessed at baseline (T₀), after gastric acid exposure (T₁), and after the second exposure (T₂). Surface morphology was examined by scanning electron microscopy. Data were analyzed with a significance level of p < 0.05. Gastric acid exposure caused a significant increase in surface roughness and a significant reduction in translucency in all materials (p < 0.05). CAD/CAM and paste-type composites exhibited significantly higher roughness values than the 3D-printed and flowable composites (p < 0.001). Fluorescence changes were observed in all groups, but the highest ΔE₀₀ values were observed in the 3D-printed and flowable composites (p < 0.001). Gastric acid adversely affected the surface and optical properties of resin-based restorative materials, while antiacid medication showed limited, material-dependent protective effects. Full article